
User's Guide
Machine type(s):
Models:
036, 037, 096, 336, 337, 388, 396, 836


Conventions
Different types of caution statements include:
Safety information 7

CAUTION—POTENTIAL INJURY: Do not cut, twist, bind, crush, or place heavy objects on the power cord. Do not subject the power cord to abrasion or stress. Do not pinch the power cord between objects such as furniture and walls. If any of these things happen, a risk of fire or electrical shock results. Inspect the power cord regularly for signs of such problems. Remove the power cord from the electrical outlet before inspecting it.
CAUTION—SHOCK HAZARD: To avoid the risk of electrical shock, if you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
Safety information 8

This product is designed, tested, and approved to meet strict global safety standards with the use of specific manufacturer's components. The safety features of some parts may not always be obvious. The manufacturer is not responsible for the use of other replacement parts.
Refer service or repairs, other than those described in the user documentation, to a service representative.
This product uses a printing process that heats the print media, and the heat may cause the media to release emissions. You must understand the section in your operating instructions that discusses the guidelines for selecting print media to avoid the possibility of harmful emissions.
This product may produce small amounts of ozone during normal operation, and may be equipped with a filter designed to limit ozone concentrations to levels well below the recommended exposure limits. To avoid high ozone concentration levels during extensive usage, install this product in a well-ventilated area and replace the ozone and exhaust filters if instructed to do so in the product maintenance instructions. If there are no references to filters in the product maintenance instructions, then there are no filters requiring replacement for this product.
SAVE THESE INSTRUCTIONS.
Safety information 9

Learning about the printer 10
Finding information about the printer

Learning about the printer 11

When selecting a location for the printer, leave enough room to open trays, covers, and doors and to install hardware options.

Learning about the printer 12


Learning about the printer 13
You can configure your printer by adding optional 250‑, 550‑, or 2100‑sheet trays. For more information, see “Installing the 250‑ or 550‑sheet tray” on page 252 or “Installing the 2100‑sheet tray” on page 253.

1 Automatic document feeder (ADF) tray
5 Standard 550‑sheet tray

Learning about the printer 14

1 Optional 2100‑sheet tray
3 Optional 250‑ or 550‑sheet trays
When using optional trays:
2 Caster base

Learning about the printer 15

1 Power cord socket Connect the printer to a properly grounded electrical outlet.
2 USB printer port Connect the printer to a computer.
3 Ethernet port Connect the printer to a network.
4 USB port Attach a keyboard or any compatible option.
5 LINE port Connect the printer to an active telephone line through a standard wall jack (RJ‑11), DSL filter, or VoIP adapter, or any other adapter that allows you to access the telephone line to send and receive faxes.

2 Home button Go to the home screen.
Use the To · Use the To

Learning about the printer 16
3 Power button • Turn on or turn off the printer.
4 Keypad Enter numbers or symbols in an input field.
5 Pause button Place a dial pause in a fax number.
6 Start button Start a job, depending on which mode is selected.
7 Clear all or Reset button Reset the default settings of a function such as copying, faxing, or scanning.
8 Stop or Cancel button Stop the current job.
9 Backspace button Move the cursor backward and delete a character in an input field.
10 Indicator light Check the status of the printer.
11 Volume buttons Adjust the volume of the headset or speaker.
12 Headset or speaker port Attach a headset or speaker.

Off The printer is off or in Hibernate mode.
Off The printer is off, ready, or processing data.
Use the To

Setting up and using the home screen applications 17
Using the home screen

1 Copy Make copies.
2 E‑mail Send e‑mails.
3 Settings Access the printer menus.
4 Fax Send fax.
5 Address Book Manage a contact list that other applications on the printer can access.
8 Job Queue Show all the current print jobs.
9 Held Jobs Show the print jobs that are held in the printer memory.
10 Shortcut Center Organize all shortcuts.
11 App Profiles Access application profiles.
Touch To

Setting up and using the home screen applications 18
12 Scan Profiles Scan and save documents directly to the computer.
13 FTP Scan and save documents directly to an FTP server.
14 Bookmarks Organize all bookmarks.
15 Change Language Change the language on the display.
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Settings > Device > Visible Home Screen Icons.
3 Select the icons that you want to appear on the home screen.
4 Apply the changes.
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Apps > Card Copy > Configure.
3 Apply the changes.
Touch To

Setting up and using the home screen applications 19
1 From the home screen, touch Shortcut Center, and then select a printer function.
2 Touch Create Shortcut, and then configure the settings.
3 Touch Save, and then type a unique shortcut name.
4 Apply the changes.
Before using the application, make sure to do the following:
1 From the Screen Saver and Slideshow Images section, add, edit, or delete an image.
2 Apply the changes.
1 From the home screen, touch Change Wallpaper.
2 Select an image to use.
3 Apply the changes.
1 Insert a flash drive into the USB port.
2 From the home screen, touch Slideshow.
Images appear in alphabetical order.
1 From the home screen, touch Scan Center.
2 Select and create a destination, and then configure the settings.

Setting up and using the home screen applications 20
3 Apply the changes.
We recommend logging in to the printer before you create a profile. To enable a login method, see the Embedded Web Server ‑ Security Admin Guide.
1 From the home screen, touch Cloud Connector.
2 Select a cloud service provider.
3 Touch Create a Profile or .
4 Type a unique profile name.
5 If necessary, enter a PIN.
6 Touch Create, and then take note of the authorization code.
7 Open a web browser, and then go to https://lexmark.cloud-connect.co.
8 Click Next, and then accept the Terms of Use.
9 Enter the authorization code, and then click Connect.
10 Log in to your cloud service provider account.
11 Grant permissions.
You may need administrative rights to access the application.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Apps > Device Quotas > Configure.
3 From the User Accounts section, add or edit a user, and then set the user quota.
4 Apply the changes.

Setting up and using the home screen applications 21
You may need administrative rights to access the application.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Apps > QR Code Generator > Configure.
4 Apply the changes.
1 From the home screen, touch Eco‑Settings.
2 Configure the Eco‑Mode settings or schedule a power-saving mode.
3 Apply the changes.
1 From the home screen, touch Customer Support.
2 Print or e‑mail the information.
Use bookmarks to print frequently accessed documents that are stored in servers or on the web.
1 Open a web browser, and then type the printer IP address in the address field.

Setting up and using the home screen applications 22
2 Click Bookmark Setup > Add Bookmark, and then type a unique name for the bookmark.
To limit access to the bookmark, enter a PIN.
4 Click Save.
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Bookmark Setup > Add Folder, and then type a unique name for the folder.
3 Click Save.
1 Open a web browser, and then type the printer IP address in the address field.

Setting up and using the home screen applications 23
2 Click Address Book.
3 From the Contacts section, add a contact.
4 If necessary, specify a login method to allow application access.
5 Apply the changes.
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Address Book.
3 From the Contact Groups section, add a group name.
4 Apply the changes.
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Address Book.
4 Apply the changes.
1 Open a web browser, and then type the printer IP address in the address field.

Setting up and using the home screen applications 24
2 Click Address Book.

Setting up and using the accessibility features 25
Activating Voice Guidance
1 Press and hold the 5 key until you hear a voice message.
2 Select OK.
1 Press and hold the 5 key until you hear a voice message.
2 Press Tab to navigate the focus cursor to the OK button, and then press Enter.
Double‑tap Select an option or item on the screen.
Triple‑tap Zoom in or zoom out text and images.
Swipe right or swipe down Move to the next item on the screen.
Swipe left or swipe up Move to the previous item on the screen.
Pan Access parts of the zoomed image that are beyond the limits of the screen.
Swipe up then left Exit an application and return to the home screen.
Swipe up then down Repeat a spoken prompt.
Gesture Function

Setting up and using the accessibility features 26
1 From the control panel, press and hold the 5 key until you hear a voice message.
2 Select Magnification mode.
3 Select OK.
For more information on navigating a magnified screen, see “Navigating the screen using gestures” on page 25.
1 From the home screen, select Settings > Device > Accessibility > Speech Rate.
2 Select the speech rate.
Do one or more of the following:
1 From the home screen, select Settings > Device > Accessibility > Speak Passwords/PINs.
2 Enable the setting.

Loading paper and specialty media 27
Setting the size and type of the specialty media
The trays automatically detect the size of plain paper. For specialty media like labels, card stock, or envelopes, do the following:
1 From the home screen, navigate to:
Settings > Paper > Tray Configuration > Paper Size/Type > select a paper source
2 Set the size and type of the specialty media.
1 From the home screen, touch Settings > Paper > Media Configuration > Universal Setup.
2 Configure the settings.
1 Remove the tray.

2 Adjust the guides to match the size of the paper that you are loading.

Loading paper and specialty media 28

3 Flex, fan, and align the paper edges before loading.

4 Load the paper stack with the printable side facedown, and then make sure that the side guides fit snugly against the paper.


Loading paper and specialty media 29

One‑sided printing Two‑sided printing


One‑sided printing Two‑sided printing



5 Insert the tray.
6 From the control panel, set the paper size and paper type to match the paper loaded.

Loading paper and specialty media 30
1 Pull out the tray.
2 Adjust the guides.
a Pull up and slide the width guide to the position for A5.


Loading paper and specialty media 31
b Squeeze and slide the length guide to the position for A5 until it clicks into place.

c Remove the A5 length guide from its holder.

d Insert the guide into its designated slot, and then press until it clicks into place.


Loading paper and specialty media 32
Loading A4‑, letter‑, legal‑, oficio‑, and folio‑size paper
a Pull up and slide the width guide to the correct position for the size of the paper being loaded.

b If the A5 length guide is still attached, then remove it. If the guide is not attached, then proceed to step
d on page 33.

c Place the A5 length guide in its holder.


Loading paper and specialty media 33
d Squeeze, and then slide the length guide to the correct position for the size of the paper being loaded.

3 Flex, fan, and align the paper edges before loading.
4 Load the paper stack with the printable side facedown. • When loading letterhead, do either of the following:
One‑sided printing Two‑sided printing



Loading paper and specialty media 34
One‑sided printing Two‑sided printing


5 Insert the tray.

6 From the printer control panel, set the paper size and paper type from the control panel to match the paper loaded.
1 Open the multipurpose feeder.


Loading paper and specialty media 35
2 Adjust the guide to match the size of the paper that you are loading.

3 Flex, fan, and align the paper edges before loading.
4 Load paper with the printable side faceup. • When loading letterhead, do either of the following:
One‑sided printing Two‑sided printing


One‑sided printing Two‑sided printing


5 From the control panel, set the paper size and paper type to match the paper loaded.
1 Open a web browser, and then type the printer IP address in the address field.

Loading paper and specialty media 36
2 Click Settings > Paper > Tray Configuration.
3 Set the same paper size and paper type for the trays that you are linking.
4 Save the settings.
5 Click Settings > Device > Maintenance > Configuration Menu > Tray Configuration.
6 Set Tray Linking to Automatic.
7 Save the settings.
To unlink trays, make sure that no trays have the same paper size and paper type settings.

Supported paper sizes

Paper size Standard 550‑sheet tray, optional 250‑ or 550‑sheet tray
Optional 2100‑sheet tray Multipurpose feeder Two‑sided printing
105 x 148 mm (4.1 x 5.8 in.) to 216 x 356 mm (8.5 x 14 in.)
1 A5 long edge feed (LEF) is recommended over A5 short edge feed (SEF).
2 Envelopes wider than 101.6 mm (4.5 in.) may crease. This paper type must be tested for acceptability.
Paper support 37


Paper size Standard 550‑sheet tray, optional 250‑ or 550‑sheet tray
Optional 2100‑sheet tray Multipurpose feeder Two‑sided printing
98.4 x 162 mm (3.9 x 6.4 in.) to 176 x 250 mm (6.9 x 9.8 in.)
1 A5 long edge feed (LEF) is recommended over A5 short edge feed (SEF).
2 Envelopes wider than 101.6 mm (4.5 in.) may crease. This paper type must be tested for acceptability.

Paper type Standard 550‑sheet tray, optional 250‑ or 550‑sheet tray
Optional 2100‑sheet tray Multipurpose feeder Two‑sided printing
1 To prevent transparencies from sticking together, print up to 20 pages only. Print the succeeding pages after three minutes.
2 Supported only in the Lexmark MX725 printer model.
Paper support 38


Paper type Standard 550‑sheet tray, optional 250‑ or 550‑sheet tray
Optional 2100‑sheet tray Multipurpose feeder Two‑sided printing
1 To prevent transparencies from sticking together, print up to 20 pages only. Print the succeeding pages after three minutes.
2 Supported only in the Lexmark MX725 printer model.

Paper type and weight Standard 550‑sheet tray, optional
60–176 g/m² grain long (16–47‑lb bond)
203 g/m² grain long (125‑lb bond)
199 g/m² grain long (110‑lb bond)
176 g/m² grain long (65‑lb bond)
1 Grain short is preferred for paper over 176 g/m² (47 lb).
2Pressure‑sensitive area must enter the printer first.
3 28‑lb bond envelopes are limited to 25% cotton content.
Paper support 39

Paper type and weight Standard 550‑sheet tray, optional
Optional 2100‑sheet tray
Multipurpose feeder Two‑sided printing
250‑ or 550‑sheet tray
138–146 g/m² grain long (37–39‑lb bond)
180 g/m² (48‑lb bond) X
140–175 g/m² (37–47‑lb bond)
75–135 g/m² (20–36‑lb bond)
60–105 g/m² (16–28‑lb bond)
1 Grain short is preferred for paper over 176 g/m² (47 lb).
2Pressure‑sensitive area must enter the printer first.
3 28‑lb bond envelopes are limited to 25% cotton content.

Printing from a computer
1 From the document that you are trying to print, open the Print dialog.
2 If necessary, adjust the settings.
3 Print the document.
LexmarkTM Mobile Print allows you to send documents and images directly to a supported Lexmark printer.
1 Open the document, and then send or share the document to Lexmark Mobile Print.
2 Select a printer.
3 Print the document.
Google Cloud PrintTM is a printing service that allows you to print to any Google Cloud Print‑ready printer.
Before you begin, make sure that:
1 From your AndroidTM mobile device, open a document or select a document from your file manager.
> Print.
3 Select a printer, and then tap .
Mopria® Print Service is a mobile printing solution for mobile devices running on Android version 4.4 or later. It allows you to print directly to any Mopria‑certified printer.
Printing 41 · 2 Tap

1 From the home screen of your mobile device, launch a compatible application.
2 Tap Print, and then select the printer.
3 Send the print job.
AirPrint is a mobile printing solution that allows you to print directly from Apple devices to an AirPrint‑certified printer.
1 From the home screen of your mobile device, launch a compatible application.
2 Select an item to print, and then tap the share icon.
3 Tap Print, and then select the printer.
4 Send the print job.
1 Insert the flash drive.

2 From the display, touch the document that you want to print.
If necessary, configure other print settings.
3 Send the print job.
Printing 42

To print another document, touch USB Drive.

– The printer supports high‑speed USB flash drives with full‑speed standard. – USB flash drives must support the File Allocation Table system (FAT16/32).
Documents:
Printing 43

1 From the control panel, navigate to:
Settings > Security > Confidential Print Setup
2 Configure the settings.
Max Invalid PIN Set the number of times an invalid PIN can be entered.
Set the expiration time for confidential print jobs.
Repeat Job Expiration Set the expiration time for a repeat print job.
Verify Job Expiration Set the expiration time that the printer prints a copy before printing the remaining copies.
Reserve Job Expiration Set the expiration time that the printer stores print jobs.
Require All Jobs to be Held
Set the printer to hold all print jobs.
Set the printer to print all documents with the same file name.
1 With a document open, click File > Print.
2 Click Properties, Preferences, Options, or Setup.
3 Click Print and Hold.
4 Select Use Print and Hold, and then assign a user name.
5 Select the print job type (Confidential, Repeat, Reserve, or Verify).
If the print job is confidential, then enter a four‑digit PIN.
6 Click OK or Print.

1 With a document open, choose File > Print.
If necessary, click the disclosure triangle to see more options.
2 From the print options or Copies & Pages menu, choose Job Routing.
3 Select the print job type (Confidential, Repeat, Reserve, or Verify).
If the print job is confidential, then assign a user name and a four‑digit PIN.
4 Click OK or Print.
1 From the home screen, touch Cloud Connector.
2 Select a cloud service provider, and then select a profile.
3 Select a file.
4 If necessary, change the settings.
5 Touch Print.
1 From the home screen, touch Settings > Reports > Print > Print Fonts.
2 Touch PCL Fonts or PostScript Fonts.
From the home screen, touch Settings > Reports > Print > Print Directory.
Printing 45

Using the automatic document feeder and scanner glass
Automatic document feeder (ADF) Scanner glass


1 Load an original document into the ADF tray or on the scanner glass.
2 From the home screen, touch Copy, and then specify the number of copies.
If necessary, adjust the copy settings.
3 Copy the document.
1 Place a photo on the scanner glass.
2 From the home screen, navigate to:
Copy > Content > Content Type > Photo
3 In the Content Source menu, select the setting that best matches the original photo.
4 Copy the photo.
Copying 46

1 Load an original document into the ADF tray or on the scanner glass.
2 From the home screen, touch Copy, and then specify the size of the original document.
3 Touch Copy to, and then select the tray that contains the specialty media.
If you are loading the specialty media into the multipurpose feeder, then navigate to:
Multipurpose Feeder > select the size of the specialty media > Letterhead
4 Send the copy job.
1 Load an original document into the ADF tray or on the scanner glass.
2 From the home screen, touch Copy > Paper Setup.
3 Adjust the settings.
4 Copy the document.
1 Load an original document into the ADF tray or on the scanner glass.
2 From the home screen, navigate to:
Copy > Scale > specify a scale value
3 Copy the document.
1 Load an original document into the ADF tray or on the scanner glass.
2 From the home screen, touch Copy, and then set Collate to On.
3 Copy the document.
1 Load an original document into the ADF tray or on the scanner glass.
2 From the home screen, touch Copy > Separator Sheets.
3 Adjust the settings.
4 Send the copy job.
Copying 47

1 Load an original document into the ADF tray or on the scanner glass.
2 From the home screen, touch Copy > Pages per Side.
3 Adjust the settings.
4 Copy the document.
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Shortcuts > Add Shortcut.
3 From the Shortcut Type menu, select Copy, and then configure the settings.
4 Apply the changes.
Copying 48

Using the automatic document feeder and scanner glass
Automatic document feeder (ADF) Scanner glass
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Settings > E‑mail > E‑mail Setup.
3 Configure the settings.
4 Apply the changes.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > E-mail.
E-mailing 49

3 Enter the needed information.
4 Apply the changes.
1 Load an original document into the ADF tray or on the scanner glass.
2 From the home screen, touch E-mail, and then enter the needed information.
3 If necessary, configure the output file type settings.
4 Send the e-mail.
1 From the control panel, press #, and then enter the shortcut number using the keypad.
2 Send the e‑mail.
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Shortcuts > Add Shortcut.
3 From the Shortcut Type menu, select E‑mail, and then configure the settings.
4 Apply the changes.
E-mailing 50

Using the automatic document feeder and scanner glass
Automatic document feeder (ADF) Scanner glass

Faxing 51

1 From the home screen, touch Settings > Device > Preferences > Run Initial Setup.
2 Turn off the printer, wait for about 10 seconds, and then turn it back on.
3 From the Before You Begin screen, select Change the Settings and Continue with the Wizard.
4 From the Fax/Email Server Setup screen, enter the needed information.
5 Finish the setup.
Faxing 52


1 Connect one end of the telephone cable to the line port of the printer.
2 Connect the other end of the cable to an active analog wall jack.
Faxing 53

Connected to different wall jacks

1 Connect one end of the telephone cable to the line port of the printer.
2 Connect the other end of the cable to an active analog wall jack.
Setting up fax in countries or regions with different telephone wall jacks and plugs
Faxing 54

The standard wall jack adopted by most countries or regions is RJ11. If the wall jack or equipment in your facility is not compatible with this type of connection, then use a telephone adapter. An adapter for your country or region may not come with your printer, and you may need to purchase it separately.
There may be an adapter plug installed in the telephone port of the printer. Do not remove the adapter plug from the telephone port of the printer if you are connecting to a serial or cascaded telephone system.
Part name Part number
Lexmark adapter plug 40X8519

Faxing 55

1 Connect one end of the telephone cable to the line port of the printer.
2 Connect the other end of the cable to the RJ11 adapter, and then connect the adapter to the wall jack.
3 If you want to connect another device with a non‑RJ11 connector to the same wall jack, then connect it directly to the telephone adapter.
The German wall jack has two kinds of ports. The N ports are for fax machines, modems, and answering machines. The F port is for telephones. Connect the printer to any of the N ports.

1 Connect one end of the telephone cable to the line port of the printer.
2 Connect the other end of the cable to the RJ11 adapter, and then connect the adapter to an N port.
3 If you want to connect a telephone and answering machine to the same wall jack, then connect the devices as shown.
Faxing 56

A distinctive ring service lets you have multiple telephone numbers on one telephone line. Each telephone number is assigned a different ring pattern.
1 From the home screen, touch Settings > Fax > Analog Fax Setup > Fax Receive Settings > Admin Controls > Answer On.
2 Select the ring pattern.
3 Apply the changes.
1 From the home screen, touch Settings > Device > Preferences > Date and Time > Configure.
2 Configure the settings.
1 From the home screen, touch Settings > Device > Preferences > Date and Time > Configure.
2 In the Time Zone menu, select Custom.
3 Configure the settings.
1 Load the original document into the ADF tray or on the scanner glass.
2 From the home screen, touch Fax, and then enter the needed information.
3 If necessary, configure other fax settings.
4 Send the fax job.
1 With a document open, click File > Print.
2 Select the printer, and then click Properties, Preferences, Options, or Setup.
3 Click Fax > Enable fax, and then enter the recipient number.
4 If necessary, configure other fax settings.
5 Send the fax job.
Faxing 57

1 With a document open, choose File > Print.
2 Select the printer and enter the recipient number.
3 If necessary, configure other fax settings.
4 Send the fax job.
1 Load the original document into the ADF tray or on the scanner glass.
2 From the home screen, navigate to:
Fax > enter the fax number > Send Time
3 Configure the date and time to send the fax.
4 If necessary, configure other fax settings.
5 Send the fax job.
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Shortcuts > Add Shortcut.
3 From the Shortcut Type menu, select Fax, and then configure the settings.
4 Apply the changes.
1 Load an original document into the ADF tray or on the scanner glass.
2 From the home screen, touch Fax, and then enter the needed information.
3 Adjust the Resolution setting.
4 Send the fax job.
Faxing 58

1 Load an original document into the ADF tray or on the scanner glass.
2 From the home screen, touch Fax, and then enter the needed information.
3 Adjust the Darkness setting.
4 Send the fax job.
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Settings > Reports > Fax.
3 Click Fax Job Log or Fax Call Log.
1 From the home screen, touch Settings > Fax > Analog Fax Setup > Fax Receive Settings > Admin Controls > Block No Name Fax.
2 Apply the changes.
1 From the home screen, touch Settings > Fax > Analog Fax Setup > Fax Receive Settings > Holding Faxes.
2 Select a mode.
1 From the home screen, touch Settings > Fax > Analog Fax Setup > Fax Receive Settings > Admin Controls.
2 Configure the Fax Forwarding, Forward To, and Forward to Shortcut settings.
3 Apply the changes.
Faxing 59

Using the automatic document feeder and scanner glass
Automatic document feeder (ADF) Scanner glass
1 Load the original document into the ADF tray or on the scanner glass.
2 From the home screen, touch FTP, and then enter the needed information.
3 If necessary, configure other FTP settings.
4 Send the FTP job.
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Shortcuts > Add Shortcut.
3 From the Shortcut Type menu, select FTP, and then configure the settings.
4 Apply the changes.
Scanning 60

1 Load an original document into the ADF tray or on the scanner glass.
2 Insert the flash drive.
3 Touch Scan to USB and adjust the settings if necessary.
4 Scan the document.
Scanning 61

1 Load an original document into the ADF tray or on the scanner glass.
2 From the home screen, touch Scan Center, and then from the list of destinations, select Fax.
3 Select a fax destination.
4 Scan the document.
1 Load an original document into the ADF tray or on the scanner glass.
2 From the home screen, touch Scan Profiles > Scan To Computer.
3 Select the scan profile where you want to save the document.
1 Load the document into the ADF tray or on the scanner glass.
2 From the home screen, touch Cloud Connector.
3 Select a cloud service provider, and then select a profile.
4 If necessary, select a folder.
5 Touch Scan.
6 If necessary, change the scan settings.
7 Touch Scan.
Scanning 62

Understanding the printer menus 63
Menu map
Copy Copy Defaults · FTP FTP Defaults

Understanding the printer menus 64
Set the language of the text that appears on the display.
Identify the country or region where the printer is configured to operate.
[List of countries or regions]
Run the setup wizard.
Select a language as a keyboard type.
Specify the information to appear on the home screen.
Display Text 1 [IP Address*] Display Text 2 [Date/Time*] Custom Text 1 Custom Text 2
Configure the printer date and time.
Current Date and Time Manually Set Date and Time Date Format [MM‑DD‑YYYY*] Time Format [12 hour A.M./P.M.*] Time Zone [GMT*]

Understanding the printer menus 65
Configure the settings for Network Time Protocol (NTP).
Enable NTP [On*] NTP Server Enable Authentication
Specify the unit of measurement for paper sizes.
U.S.* Metric
20–100% (100*) Adjust the brightness of the display.
Enable access to the flash drive.
Specify whether background removal is allowed.
Allow Custom Job scans
Scan multiple jobs to one file.
One Page Flatbed Scanning
Set copies from the scanner glass to only one page at a time.
Enable audio feedback for button presses, panel interactions, paper loaded prompts, and error notifications.
Adjust the volume of the printer speakers.
10–300 (60*) Set the idle time in seconds before the display shows the home screen, or before the printer logs off a user account automatically.

Understanding the printer menus 66
Connect an external Virtual Network Computing (VNC) client to the remote control panel.
Set the authentication type when accessing the VNC client server.
Set the indicator light to come on when a printer error occurs.
Enable a sound when loading paper into the ADF.
Set the number of times that the alarm sounds when the printer requires user intervention.
Show the estimated status of the supplies.
Show estimates* Do not show estimates
Determine the unit that the printer uses to estimate supply usage and trigger custom notifications when user intervention is required.
Set the number of times that the alarm sounds when the toner cartridge is low.
Configure notification settings when the printer requires user intervention.

Understanding the printer menus 67
E‑mail Alerts Setup Configure the printer to send e‑mail alerts to a list of contacts when the printer requires user intervention.
Set the printer to flush automatically blank pages or pages with partial prints after a jammed page is cleared.
Let the printer to continue processing or printing a job automatically after clearing certain attendance conditions.
Set the printer to restart when an error occurs.
Reboot when idle Reboot always* Reboot never
Set the number of automatic reboots that the printer can perform.
Set the number of seconds before the printer performs an automatic reboot.
Show a read‑only information of the reboot counter.
Reset the values of the Auto Reboot Counter.
Reset Auto Reboot Counter
Set the printer to show a message when a short paper error occurs.
Display Short Paper Error
On Auto‑clear*
Set the printer to process the entire page into the memory before printing it.

Understanding the printer menus 68
Set the printer to reprint jammed pages.
Specify how to restart a scan job after resolving a paper jam.
Job level Page level*
Allow printing with the display turned off.
Print With Display Off
Display on when printing Allow printing with display off*
Set the idle time before the printer begins operating in Sleep mode.
Set the time before the printer enters Hibernate mode.
Disabled 1 hour 2 hours 3 hours 6 hours 1 day 2 days 3 days* 1 week 2 weeks 1 month
Set the printer to Hibernate mode even when an active Ethernet connection exists.
Hibernate Timeout on Connection
Hibernate Do Not Hibernate*

Understanding the printer menus 69
Minimize the use of energy, paper, or specialty media.
Off* Energy Energy/Paper Paper
Schedule the printer when to enter Sleep or Hibernate mode.
Information Sent to Lexmark
Send printer usage and performance information to Lexmark.
Supplies and Page Usage (Anonymous) Device Performance (Anonymous) None of the Above
Start Time Stop Time
User Information ‑ Level
Anonymous Session Information Only* Session Information with Generic User Information Session Information with Actual User IDs
Duplicate Key Strike Interval
0–5 (0*) Set the interval in seconds during which the printer ignores duplicate key presses on an attached keyboard.
Key Repeat Initial Delay
0.25–5 (1*) Set the initial length of delay in seconds before a repeating key starts repeating.
0.5–30 (30*) Set the number of presses per second for a repeating key.

Understanding the printer menus 70
Let the user remain in the same location and reset the Screen Timeout timer when it expires instead of returning to the home screen.
1–10 (5*) Adjust the headphone volume.
Enable Voice Guidance When Headphone Is Attached
Enable Voice Guidance when a headphone is attached to the printer.
Set the printer to read out loud passwords or personal identification numbers.
Set the Voice Guidance speech rate.
Very Slow Slow Normal* Fast Faster Very Fast Rapid Very Rapid Fastest
Restore the printer factory default settings.
Restore all settings Restore printer settings Restore network settings Restore app settings

Understanding the printer menus 71
Change the USB driver mode of the printer to improve its compatibility with a personal computer.
Set whether the USB device driver enumerates as a USB Simple device (single interface) or as a USB Composite device (multiple interfaces).
USB Scan to Local
Set the USB port to run at full speed and disable its high‑speed capabilities.
Set the printer to link the trays that have the same paper type and paper size settings.
Show the Tray Insert message.
Show Tray Insert Message
Off Only for unknown sizes* Always
Specify the page orientation when loading A5‑size paper.
Short Edge* Long Edge
Set the paper source that the user fills when a prompt to load paper or envelope appears.
Auto* Multipurpose Feeder Manual Paper Envelope Prompts
Auto* Multipurpose Feeder Manual Envelope

Understanding the printer menus 72
Set the printer to resolve paper- or envelope-related change prompts.
Prompt user* Continue Use current
Print reports about printer menu settings, status, and event logs.
Menu Settings Page Event Log Event Log Summary
Supply Usage And Counters
Reset the supply page counter or view the total printed pages.
Clear Supply Usage History Reset Black Cartridge Counter Reset Black Imaging Unit Counter Reset Maintenance Counter
Set the printer to recognize and use the PPDS data stream.
Set the fax chip to enter low‑power mode whenever the printer determines that it should.
Fax Low Power Support
Disable Sleep Permit Sleep Auto*
Set a text point-size value below which the high‑frequency screens are used when printing font data.
For example, if the value is 24, then all fonts sized 24 points or less use the high‑frequency screens.
Adjust the toner density when printing or copying documents.
1–5 (3*) Copy Density
Set the printer to operate in Quiet Mode.
Enable access to the control panel menus.

Understanding the printer menus 73
Set the printer to operate in a special mode, in which it attempts to continue offering as much functionality as possible, despite known issues.
For example, when set to On and the duplex motor is nonfunctional, the printer performs one‑sided printing for a two‑sided print job.
Set the memory allocation for storing copy jobs.
Erase user‑defined strings for the Default or Alternate custom messages.
Erase messages that were remotely installed.
Clear all remotely‑installed messages
Show existing error messages on the display after the printer remains inactive on the home screen for a length of time equal to the Screen Timeout setting.
Automatically Display Error Screens
Enable the printer to use the Orientation setting under the Copy menu when sending quick copy jobs.
Honor orientation on fast path copy
Manually register the flatbed and ADF after replacing the ADF, scanner glass, or controller board.
Front ADF Registration Rear ADF Registration Flatbed Registration
Set the size, in millimeters, of the no‑print area around an ADF or flatbed scan job.
0–6 (3*) Flatbed Edge Erase
Disable the scanner if it is not working properly.
Enabled* Disabled ADF Disabled

Understanding the printer menus 74
Print a test page that shows the scanner margin settings.
Determine the byte order of a TIFF‑formatted scan output.
CPU Endianness* Little Endian Big Endian
Set the RowsPerStrip tag value of a TIFF‑formatted scan output.
Exact Tiff Rows Per Strip
Out of Service Erase
Show information on when the printer memory or hard disk was last sanitized.
Memory Last Sanitized Hard Disk Last Sanitized
Out of Service Erase
Clear all settings and applications that are stored in the printer memory or hard disk.
Sanitize all information on nonvolatile memory Sanitize all information on hard disk Erase all printer and network settings
Status/Supplies Job Queue Change Language Address Book Bookmarks Held Jobs USB App Profiles Display Customization Eco‑Settings
Specify which icons to show on the home screen.

Understanding the printer menus 75
Asset Tag Show the serial number of the printer.
Printer’s Location Identify the printer location. Maximum length is 63 characters.
Contact Personalize the printer name. Maximum length is 63 characters.
Export Configuration File to USB Export configuration files to a flash drive.
Export Compressed Logs to USB Export compressed log files to a flash drive.
Specify whether to print on one side or two sides of the paper.
1‑sided* 2‑sided
Determine which side of the paper (long edge or short edge) is bound when performing two‑sided printing.
Long Edge* Short Edge
Print blank pages that are included in a print job.
Print Do Not Print*
Keep the pages of a print job stacked in sequence, particularly when printing multiple copies of the job.
Off [1,1,1,2,2,2]* On [1,2,1,2,1,2]
Insert blank separator sheets when printing.
None* Between Copies Between Jobs Between Pages
Specify the paper source for the separator sheet.
Tray [x] (1*) Multipurpose Feeder

Understanding the printer menus 76
Print multiple page images on one side of a sheet of paper.
Off* 2 pages per side 3 pages per side 4 pages per side 6 pages per side 9 pages per side 12 pages per side 16 pages per side
Pages per Side Ordering
Specify the positioning of multiple page images when using Pages per Side.
Horizontal* Reverse Horizontal Vertical Reverse Vertical
Specify the orientation of a multiple‑page document when using Pages per Side.
Pages per Side Orientation
Pages per Side Border
Print a border around each page image when using Pages per Side.
1–9999 (1*) Specify the number of copies for each print job.
Set the printable area on a sheet of paper.
Normal* Fit to page Whole Page
Set the printer language.
PCL Emulation PS Emulation*
Preserve print jobs requiring supplies so that jobs not requiring the missing supplies can print.

Understanding the printer menus 77
0–255 (30*) Set the time in seconds that the printer waits for user intervention before it holds jobs that require unavailable resources and continues to print other jobs in the print queue.
Determine how the color imaging unit operates during printing.
Max Speed Max Yield*
Specify where to save all permanent resources, such as fonts and macros, that have been downloaded to the printer.
Determine what the printer does with downloaded resources, such as fonts and macros, when it receives a job that requires more than the available memory.
Specify the order in which held and confidential jobs are printed when Print All is selected.
Alphabetical* Newest First Oldest First
Set the resolution for the text and images on the printed output.
300 dpi 600 dpi* 1200 dpi 1200 Image Q 2400 Image Q

Understanding the printer menus 78
Enable more pixels to print in clusters for clarity, in order to enhance text and images.
Off* Fonts Horizontally Vertically Both directions Isolated
1–10 (8*) Determine the lightness or darkness of text images.
Enhance the printed output to have smoother lines with sharper edges.
Adjust the brightness of the printed output.
‑6 to 6 (0*)
0 to 5 (0*) Adjust the contrast of the printed output.
Adjust the contrast enhancement applied to images.
Set the printer to create a log of the print jobs that it receives.
Specify how often the printer creates a log file.
Log Action at End of Frequency
Specify how the printer responds when the frequency threshold expires.
None* E‑mail Current Log E‑mail & Delete Current Log Post Current Log Post & Delete Current Log

Understanding the printer menus 79
Log Near Full Level
Specify the maximum size of the log file before the printer executes the Log Action at Near Full.
Log Action at Near Full
Specify how the printer responds when the hard disk is nearly full.
None* E‑mail Current Log E‑mail & Delete Current Log E‑mail & Delete Oldest Log Post Current Log Post & Delete Current Log Post & Delete Oldest Log Delete Current Log Delete Oldest Log Delete All But Current Delete All Logs
Log Action at Full
Specify how the printer responds when disk usage reaches the maximum limit (100MB).
None* E‑mail & Delete Current Log E‑mail & Delete Oldest Log Post & Delete Current Log Post & Delete Oldest Log Delete Current Log Delete Oldest Log Delete All But Current Delete All Logs
URL to Post Log Specify where the printer posts job accounting logs.
E‑mail Address to Send Logs Specify the e‑mail address to which the printer sends job accounting logs.
Log File Prefix Specify the prefix for the log file name.
Print a test page that contains information on errors, including XML markup errors.
1–30 (2*) Set the minimum stroke width of any job printed in 1200 dpi.

Understanding the printer menus 80
Scale the page content to fit the selected paper size.
Specify whether to print annotations in the PDF.
Print Do Not Print*
Print a page that contains the PostScript error.
Lock PS Startup Mode
Disable the PostScript SysStart file.
Enhance the contrast and sharpness of low‑resolution images.
Set the printer to wait for more data before canceling a print job.
Disabled 15‑65535 (40*)
Select the source which contains the default font selection.
Resident* Disk Flash All
Select a font from the specified font source.
[List of available fonts] (Courier*)

Understanding the printer menus 81
Specify the symbol set for each font name.
[List of available symbol set] (10U PC‑8*)
0.08–100 (10*) Specify the pitch for fixed or monospaced fonts.
Specify the orientation of text and graphics on the page.
1–255 Specify the number of lines of text for each page printed through the PCL® datastream.
PCL5 Minimum Line Width
1–30 (2*) Set the initial minimum stroke width.
PCLXL Minimum Line Width
Set the width of the logical page on A4‑size paper.
198 mm* 203 mm
Auto CR after LF
Set the printer to perform a carriage return after a line feed control command.
Auto LF after CR
Set the printer to perform a line feed after a carriage return control command.
Configure the printer to work with a different print driver or custom application that uses a different set of source assignments to request a given paper source.
Assign MP Feeder Assign Tray [x] Assign Manual Paper Assign Manual Envelope
Choose from the following options:
0–199—A numeric value to assign a custom value to a paper source. 200—The printer uses the factory default paper source assignments. 201—The paper source ignores the Select Paper Feed command.
Show the factory default value assigned for each paper source.

Understanding the printer menus 82
Restore the tray renumber values to their factory defaults.
Set the printer to end a print job after it has been idle for the specified amount of time in seconds.
Set the font to use for HTML documents.
[List of fonts] (Times*)
1–255 (12*) Set the font size to use for HTML documents.
1–400% (100*) Scale HTML documents.
Set the page orientation for HTML documents.
8–255 mm (19*) Set the page margin for HTML documents.
Print background information or graphics for HTML documents.
Do Not Print Print*
Select the best available paper size and orientation setting for an image.
Invert bitonal monochrome images.

Understanding the printer menus 83
Adjust the image to fit the printable area.
Best Fit* Anchor Top Left Anchor Center Fit Height/Width Fit Height Fit Width
Specify the orientation of text and graphics on the page.
Portrait* Landscape Reverse Portrait Reverse Landscape
Set the paper source for all print jobs.
Tray [x] (1*) Multipurpose Feeder Manual Paper Manual Envelope
Specify the paper size or paper type loaded in each paper source.
Tray [x] Multipurpose Feeder Manual Paper Manual Envelope
Set the printer to substitute a specified paper size if the requested size is not loaded in any paper source.
Off Letter/A4 All Listed*

Understanding the printer menus 84
Set the printer when to pick paper loaded in the multipurpose feeder.
Specify the unit of measurement for the universal paper.
Set the portrait width of the universal paper.
3–52 inches (8.50*) 76–1321 mm (216*)
Set the portrait height of the universal paper.
3–52 inches (14*) 76–1321 mm (356*)
Set the printer to pick paper from the short edge or long edge direction.
Short Edge* Long Edge

Understanding the printer menus 85
Custom Scan Size [x]
Assign a scan size name and configure the scan settings.
Scan Size Name Width
1–8.50 inches (8.50*) 25–216 mm (216*) Height
1–14 inches (14*) 25–356 mm (297*) Orientation
Portrait* Landscape 2 scans per side Off* On
Plain Card Stock Transparency Recycled Labels Vinyl Labels Bond Envelope Rough Envelope Letterhead Preprinted Colored Paper Light Heavy Rough/Cotton Custom Type [x]
Specify the texture, weight, and orientation of the paper loaded.
Menu item Description · Menu item Description

Understanding the printer menus 86
Improve the output result based on the content of the original document.
Text Text/Photo* Photo Graphics
Improve the output result based on the source of the original document.
Black and White Laser* Color Laser Inkjet Photo/Film Magazine Newspaper Press Other
Specify the scanning behavior based on the original document.
1 sided to 1 sided* 1 sided to 2 sided 2 sided to 1 sided 2 sided to 2 sided
Specify whether to insert blank separator sheets when printing.
None* Between Copies Between Jobs Between Pages
Specify the paper source for the separator sheet.
Tray [x] (1*) Multipurpose Feeder
Specify the number of page images to print on one side of a sheet of paper.
Off* 2 Portrait pages 4 Portrait pages 2 Landscape pages 4 Landscape pages
Place a border around each image when printing multiple pages on a single page.

Understanding the printer menus 87
Print multiple copies in sequence.
Off [1,1,1,2,2,2] On [1,2,1,2,1,2]*
Copy from Size [List of paper sizes]
Set the paper size of the original document.
Specify the paper source for the copy job.
Tray [x] (1*) Multipurpose Feeder Auto Size Match
Adjust the darkness of the scanned image.
‑4 to 4 (0*)
1–9999 (1*) Specify the number of copies.
Apply a header or footer on the printed output.
Top left Top middle Top right Bottom left Bottom middle Bottom right
Specify the overlay text printed on each page of the copy job.
Confidential Copy Draft Urgent Custom Off*
Custom overlay Type a custom overlay text.

Understanding the printer menus 88
Specify which color to drop during scanning, and adjust the dropout setting for that color.
None* Red Green Blue
Specify the contrast of the output.
Best for Content* 0 1 2 3 4 5
Adjust the amount of background visible on a scanned image.
Align the content at the center of the page.
Create a mirror image of the original document.
Create a negative image of the original document.
Adjust the amount of shadow detail visible on a scanned image.
‑4 to 4 (0*)
Allow edge‑to‑edge scanning of the original document.
Scan Edge to Edge
1–5 (3*) Adjust the sharpness of a scanned image.

Understanding the printer menus 89
Insert a blank sheet between transparencies.
Interrupt a print job to copy a page or document.
Turn on scanning of custom jobs by default.
Allow Save as Shortcut
Save custom copy settings as shortcuts.
Sample Copy Print a sample copy.
Select a fax mode.
Analog* Fax Server Disabled
Fax Name Identify your fax machine.
Fax Number Identify your fax number.
Notify fax recipients of your fax name or fax number.
Fax Name Fax Number*

Understanding the printer menus 90
Set the printer to fax manually.
Set the amount of internal printer memory allocated for faxing.
All receive Mostly receive Equal* Mostly send All send
Cancel outgoing faxes before they are transmitted, or cancel incoming faxes before they finish printing.
Show the telephone number of the person sending the fax.
Specify the format for masking an outgoing fax number.
Off* From Left From Right
0–58 (0*) Specify the number of digits to mask in an outgoing fax number.
Enable Line Connected Detection
Determine whether a telephone line is connected to the printer.
Enable Line In Wrong Jack Detection
Determine whether a telephone line is connected to the correct port on the printer.

Understanding the printer menus 91
Enable Extension in Use Support
Determine whether a telephone line is used by another device such as another phone on the same line.
Optimize Fax Compatibility Configure the printer fax functionality for optimal compatibility with other fax machines.
Set the resolution of the scanned image.
Standard* Fine Super Fine Ultra Fine
Specify the size of the original document.
[List of paper sizes]
Specify the orientation of the original document.
Specify the page orientation of text and graphics when scanning a two‑sided document.
Off* Long Edge Short Edge
Improve the output result based on the content of the original document.
Text* Text/Photo Photo Graphics
Improve the output result based on the source of the original document.
Black and White Laser* Color Laser Inkjet Photo/Film Magazine Newspaper Press Other

Understanding the printer menus 92
Adjust the darkness of the scanned image.
‑4 to 4 (0*)
Set the printer to dial a fax number without waiting to recognize the dial tone.
Specify the dial mode for incoming or outgoing faxes.
Adjust the amount of toner used for each color.
‑4 to 4 (0*)
Specify which color to drop during scanning, and adjust the dropout setting for that color.
None* Red Green Blue
Set the contrast of the output.
Best for Content* 0 1 2 3 4 5
Adjust the amount of background visible on a scanned image.
Content‑based* Fixed Level
‑4 to 4 (0*)

Understanding the printer menus 93
Create a mirror image of the original document.
Create a negative image of the original document.
Adjust the amount of shadow detail visible on a scanned image.
‑4 to 4 (0*)
Allow edge‑to‑edge scanning of the original document.
Scan Edge to Edge
1–5 (3*) Adjust the sharpness of the scanned image.
Specify whether to generate a cooler or warmer output.
‑4 to 4 (0*)
0–9 (5*) Adjust the number of redial attempts based on the activity levels of recipient fax machines.
1–200 minutes (3*) Increase the time between redial attempts to increase the chance of sending fax successfully.
Activate Error Correction Mode (ECM) for fax jobs.
Fax documents that are scanned at the printer.
Allow the print driver to send fax.
Allow Save as Shortcut
Save fax numbers as shortcuts in the printer.

Understanding the printer menus 94
Set the maximum speed for sending fax.
33600* 14400 9600 4800 2400
Turn on scanning of custom jobs by default.
Show a preview of the scan on the display.
Enable Color Fax Scans
Enable color scans for fax.
Off by default* On by default Never use Always use
Auto Convert Color Faxes to Mono Faxes
Convert all outgoing color faxes to black and white.
Ask the user to confirm the fax number.
Dial Prefix Set a dialing prefix.
Establish a dialing prefix rule.
Remove fax jobs that request specific unavailable resources from the print queue.
None* Toner Toner and Supplies
1–25 (3*) Set the number of rings for incoming fax.

Understanding the printer menus 95
Scale incoming fax to fit on the page.
Set the paper source for printing incoming fax.
Tray [x] Multipurpose Feeder Auto*
Print on both sides of the paper.
Specify whether to insert blank separator sheets when printing.
None* Before Job After Job
Specify the paper source for the separator sheet.
Tray [x] (1*) Multipurpose Feeder
Specify the output bin for received faxes.
Print the transmission information at the bottom of each page from a received fax.
Fax Footer Time Stamp
Print the time stamp at the bottom of each page from a received fax.
Hold received faxes from printing until they are released.
Off* Always On Manual Scheduled
Set the printer to receive fax.

Understanding the printer menus 96
Show the number that is sending the incoming fax.
Block No Name Fax
Block incoming faxes sent from devices with no station ID or fax ID specified.
Specify the phone numbers that you want to block.
Set a distinctive ring pattern for incoming fax.
All Rings* Single Ring Only Double Ring Only Triple Ring Only Single or Double Rings Only Single or Triple Rings Only Double or Triple Rings Only
Set the printer to receive fax automatically.
0–9 (9*) Manually enter a code on the telephone number pad to begin receiving fax.
Specify how to forward received fax.
Print* Print and Forward Forward
Specify where to forward received fax.
Confirmation E‑mail Send a confirmation e‑mail when fax forwarding is successful.

Understanding the printer menus 97
Set the maximum speed for transmitting fax.
33600* 14400 9600 4800 2400
Configure the settings for the fax cover page.
Off by Default* On by Default Never Use Always Use
Message:

Understanding the printer menus 98
Print a log for successful fax transmission or transmission error.
Print log* Do Not Print Log Print Only For Error
Print a log for fax‑receive failures.
Print Never* Print on Error
Print all fax activity.
Specify the paper source for printing logs.
Tray [x] (1*) Multipurpose Feeder
Identify the sender by remote fax name or fax number.
Remote Fax Name* Dialed Number
View a summary of all fax jobs.
View a summary of fax dialing history.
Specify the output bin for printed logs.
Standard Bin* Bin [x]
Set the fax speaker mode.
Always Off Always On On until Connected*
Adjust the fax speaker volume.

Understanding the printer menus 99
Enable the ringer volume.
To Format Specify a fax recipient.
Reply Address Specify a reply address for sending fax.
Subject Specify the fax subject and message.
Set the printer to receive analog faxes.
Primary SMTP Gateway Type the IP address or host name of the primary Simple Mail Transfer Protocol (SMTP) server for sending e-mail.
Primary SMTP Gateway Port
1–65535 (25*) Enter the port number of the primary SMTP server.
Secondary SMTP Gateway Type the server IP address or host name of your secondary or backup SMTP server.
Secondary SMTP Gateway Port
1–65535 (25*) Enter the server port number of your secondary or backup SMTP server.
5–30 (30*) Set the time before the printer times out if the SMTP server does not respond.
Reply Address Specify a reply address for sending fax.
Always use SMTP default Reply Address
Specify the SMTP reply address for sending fax.

Understanding the printer menus 100
Specify whether to send fax using an encrypted link.
Specify a trusted certificate when accessing the SMTP server.
Set the authentication type for the SMTP server.
No authentication required* Login / Plain NTLM CRAM‑MD5 Digest‑MD5 Kerberos 5
Device‑Initiated E‑mail
Specify whether credentials are required for device‑initiated e‑mail.
None* Use Device SMTP Credentials
User‑Initiated E‑mail
Specify whether credentials are required for user‑initiated e‑mail.
None* Use Device SMTP Credentials Use Session User ID and Password Use Session E‑mail address and Password Prompt user
Use Active Directory Device Credentials
Enable user credentials and group destinations to connect to the SMTP server.
Device Userid Specify the user ID and password to connect to the SMTP server.
Kerberos 5 REALM Specify the realm for the Kerberos 5 authentication protocol.
NTLM Domain Specify the domain name for the NTLM security protocol.
Disable "SMTP server not set up" error
Hide the “SMTP server not set up” error message.

Understanding the printer menus 101
Specify the file format for the scanned image.
TIFF (.tif) PDF (.pdf)* XPS (.xps) TXT (.txt) RTF (.rtf) DOCX (.docx)
Improve the output result based on the content of the original document.
Text Text/Photo* Photo Graphics
Improve the output result based on the source of the original document.
Black and White Laser Color Laser* Inkjet Photo/Film Magazine Newspaper Press Other
Set the fax resolution.
Standard* Fine Super Fine Ultra Fine
1–9 (5*) Set the darkness of the output.
Specify the orientation of text and graphics on the page.
Set the paper size of the original document.
[List of paper sizes]
Use Multi‑Page TIFF
Choose between single‑ and multiple‑page TIFF files.

Understanding the printer menus 102
Primary SMTP Gateway Type the IP address or host name of the primary SMTP server for sending e- mail.
Primary SMTP Gateway Port
1–65535 (25*) Enter the port number of the primary SMTP server.
Secondary SMTP Gateway Type the server IP address or host name of your secondary or backup SMTP server.
Secondary SMTP Gateway Port
1–65535 (25*) Enter the server port number of your secondary or backup SMTP server.
5–30 seconds (30*) Set the time before the printer times out if the SMTP server does not respond.
Reply Address Specify a reply address in the e‑mail.
Always use SMTP default Reply Address
Always use the default reply address in the SMTP server.
Specify whether to send e‑mail using an encrypted link.
Require a trusted certificate when accessing the SMTP server.
Set the authentication type for the SMTP server.
No authentication required* Login / Plain NTLM CRAM‑MD5 Digest‑MD5 Kerberos 5
Device‑Initiated E‑mail
Specify whether credentials are required for device‑initiated e‑mail.
None* Use Device SMTP Credentials

Understanding the printer menus 103
User‑Initiated E‑mail
Specify whether credentials are required for user‑initiated e‑mail.
None* Use Device SMTP Credentials Use Session User ID and Password Use Session E‑mail address and Password Prompt user
Use Active Directory Device Credentials
Enable user credentials and group designations to connect to the SMTP server.
Device Userid Specify the user ID and password to connect to the SMTP server.
Kerberos 5 REALM Specify the realm for the Kerberos 5 authentication protocol.
NTLM Domain Specify the domain name for the NTLM security protocol.
Disable "SMTP server not set up" error
Hide the “SMTP server not set up” error message.
Subject Specify the e‑mail subject and message.
File Name Specify the file name for the scanned image.
Specify the file format for the scanned image.
PDF (.pdf)* TIFF (.tif) JPEG (.jpg) XPS (.xps) TXT (.txt) RTF (.rtf) DOC (.docx)

Understanding the printer menus 104
Configure the settings for optical character recognition (OCR).
Recognized Languages Auto Rotate Despeckle Auto Contrast Enhance
Set the PDF format of the scanned image.
1.3 1.4 1.5* 1.6 1.7 Archival Version
A‑1a* A‑1b Highly Compressed
Off* On Archival (PDF/A)
Improve the output result based on the content of the original document.
Text Text/Photo* Photo Graphics
Improve the output result based on the original document.
Black and White Laser* Color Laser Inkjet Photo/Film Magazine Newspaper Press Other

Understanding the printer menus 105
Specify the color when scanning an image.
Black and White Gray Color* Auto
Set the resolution of the scanned image.
75 dpi 150 dpi* 200 dpi 300 dpi 400 dpi 600 dpi
Adjust the darkness of the scanned image.
-4 to 4 (0*)
Specify the orientation of text and graphics on the page.
Set the paper size of the original document.
[List of paper sizes]
Specify the page orientation of text and graphics when scanning a two‑sided document.
Off* Long Edge Short Edge
Adjust the amount of toner being used for each color.
-4 to 4 (0*)
Specify which color to drop during scanning, and adjust the dropout setting for that color.
None* Red Green Blue Default Red Threshold
0–255 (128*) Default Green Threshold
0–255 (128*) Default Blue Threshold

Understanding the printer menus 106
Set the amount of color that the printer detects from the original document.
1–9 (5*) Area Sensitivity
Set the quality of a JPEG‑format scanned image.
Best for content* 5–95
Specify the contrast of the output.
Best for content* 0 1 2 3 4 5
Adjust the amount of background visible on a scanned image.
Content‑based* Fixed Level
‑4 to 4 (0*)
Create a mirror image of the original document.
Create a negative image of the original document.
Adjust the amount of shadow detail visible on a scanned image.
‑4 to 4 (0*)
Scan Edge to Edge
Allow edge‑to‑edge scanning of the original document.
1–5 (3*) Adjust the sharpness of a scanned image.
Specify whether to generate a cooler or warmer output.
‑4 to 4 (0*)

Understanding the printer menus 107
Specify whether to include blank pages.
Blank Page Removal Blank Page Sensitivity
Max E‑mail Size
0–65535 (0*) Set the allowable file size for each e‑mail.
Size Error Message Specify an error message that the printer sends when an e‑mail exceeds its allowable file size.
Limit Destinations Limit sending of e‑mail only to the specified list of domain names.
Send a copy of the e‑mail to yourself.
Send Me a Copy
Never appears* On by Default Off by Default Always On
Limit E‑mail Recipients
Limit the number of e‑mail recipients.
Use cc:/bcc:
Enable carbon copy and blind carbon copy in e‑mail.
Use Multi‑Page TIFF
Choose between single- and multiple‑page TIFF files.
Set a compression option for TIFF files.
5–95 (75*) Set the quality of text on a scanned image.
5–95 (75*) Set the quality of text or photo on a scanned image.
5–95 (50*) Set the quality of a photo on a scanned image.

Understanding the printer menus 108
E‑mail Bit Depth
Enable the Text/Photo mode to produce smaller file sizes by using 1‑bit image.
1 bit 8 bit*
Print a log for successful e‑mail transmission.
Print log* Do Not Print Log Print Only For Error
Specify the paper source for printing logs.
Tray [x] (1*) Multipurpose Feeder
Turn on scanning of custom jobs by default.
Show the scan preview on the display.
Allow Save as Shortcut
Save e-mail addresses as shortcuts.
E‑mail Images Sent As
Specify how to send the images in e‑mail.
Reset E-mail Information After Sending
Restore the default e-mail information after sending an e-mail.
Server Set the printer to send e‑mail as a web link.

Understanding the printer menus 109
Specify the file format for the scanned image.
PDF (.pdf)* TIFF (.tif) JPEG (.jpg) XPS (.xps) TXT (.txt) RTF (.rtf) DOCX (.docx)
Configure the settings for optical character recognition (OCR).
Recognized Languages Auto Rotate Despeckle Auto Contrast Enhance
Set the PDF format for the scanned image.
1.3 1.4 1.5* 1.6 1.7 Archival Version
A‑1a* A‑1b Secure
Off* On Archival (PDF/A)
Improve the output result based on the content of the original document.
Text Text/Photo* Graphics Photo

Understanding the printer menus 110
Improve the output result based on the source of the original document.
Black and White Laser Color Laser* Inkjet Photo/Film Magazine Newspaper Press Other
Specify the color when scanning an image.
Black and White Gray Color* Auto
Set the resolution of the scanned image.
75 dpi 150 dpi* 200 dpi 300 dpi 400 dpi 600 dpi
Adjust the darkness of the scanned image.
-4 to 4 (0*)
Specify the orientation of text and graphics on the page.
Set the paper size of the original document.
[List of paper sizes]
Specify the page orientation of text and graphics when scanning a two‑sided document.
Off* Long Edge Short Edge
File Name Specify the file name of the scanned image.

Understanding the printer menus 111
Adjust the amount of toner used for each color in scan output.
-4 to 4 (0*)
Specify which color to drop during scanning, and adjust the dropout setting for that color.
None* Red Green Blue Default Red Threshold
0–255 (128*) Default Green Threshold
0–255 (128*) Default Blue Threshold
Set the amount of color that the printer detects from the original document.
1–9 (5*) Area Sensitivity
Set the quality of a JPEG‑format image.
Best for content* 5–95
Specify the contrast of the output.
Best for content* 0 1 2 3 4 5
Adjust the amount of background visible on a scanned image.
Content‑based* Fixed Level
‑4 to 4 (0*)
Create a mirror image of the original document.

Understanding the printer menus 112
Create a negative image of the original document.
Adjust the amount of shadow detail visible on a scanned image.
‑4 to 4 (0*)
Allow edge‑to‑edge scanning of the original document.
Scan Edge to Edge
1–5 (3*) Adjust the sharpness of a scanned image.
Specify whether to generate a cooler or warmer output.
‑4 to 4 (0*)
Specify whether to include blank pages.
Blank Page Removal Blank Page Sensitivity
5–95 (75*) Set the quality of text on a scanned image.
5–95 (75*) Set the quality of text or photo image on a scanned image.
5–95 (50*) Set the quality of a photo image on a scanned image.
Use Multi‑Page TIFF
Choose between single- and multiple‑page TIFF files.
Set a compression option for TIFF files.
Print a log for successful FTP scan transmission.
Print Log* Do Not Print Log Print Only For Error
Specify the paper source for printing FTP logs.
Tray [x] (1*) Multipurpose Feeder

Understanding the printer menus 113
Enable the Text/Photo mode to have smaller file sizes by using 1‑bit image.
1 bit 8 bit*
Turn on scanning of custom jobs by default.
Show a preview of the scan on the display.
Allow Save as Shortcut
Save custom FTP settings as shortcuts.
Specify the file format for the scanned image.
PDF (.pdf)* TIFF (.tif) JPEG (.jpg) XPS (.xps)
Configure the settings for optical character recognition (OCR).
Recognized Languages Auto Rotate Despeckle Auto Contrast Enhance

Understanding the printer menus 114
Set the PDF format for the scanned image.
1.3 1.4 1.5* 1.6 1.7 Archival Version
A‑1a* A‑1b Secure
Off* On Archival (PDF/A)
Improve the output result based on the content of the original document.
Text Text/Photo* Graphics Photo
Improve the output result based on the source of the original document.
Black and White Laser Color Laser* Inkjet Photo/Film Magazine Newspaper Press Other
Specify the color when scanning an image.
Black and White Gray Color* Auto
Set the resolution of the scanned image.
75 dpi 150 dpi* 200 dpi 300 dpi 400 dpi 600 dpi

Understanding the printer menus 115
1–9 (5*) Adjust the darkness of the scanned image.
Specify the orientation of text and graphics on the page.
Set the paper size of the original document.
[List of paper sizes]
Specify the page orientation of text and graphics when scanning a two‑sided document.
Off* Long edge Short edge
File Name Specify the file name of the scanned image.
Color Balance Adjust the amount of toner used for each color.
Specify which color to drop during scanning, and adjust the dropout setting for that color.
None* Red Green Blue Default Red Threshold
0–255 (128*) Default Green Threshold
0–255 (128*) Default Blue Threshold
Set the amount of color that the printer detects from the original document.
1–9 (5*) Area Sensitivity

Understanding the printer menus 116
Set the quality of a JPEG‑format image.
Best for content* 5–95
Specify the contrast of the output.
Best for content* 0 1 2 3 4 5
Adjust the amount of background visible on a scanned image.
Content‑based* Fixed Level
‑4 to 4 (0*)
Create a mirror image of the original document.
Create a negative image of the original document.
Adjust the amount of shadow detail visible on a scanned image.
‑4 to 4 (0*)
Allow edge‑to‑edge scanning of the original document.
Scan Edge to Edge
1–5 (3*) Adjust the sharpness of a scanned image.
Specify whether to generate a cooler or warmer output.
‑4 to 4 (0*)
Specify whether to include blank pages.
Blank Page Removal Blank Page Sensitivity

Understanding the printer menus 117
5–95 (75*) Set the quality of text on a scanned image.
5–95 (75*) Set the quality of text or photo on a scanned image.
5–95 (75*) Set the quality of a photo on a scanned image.
Use Multi‑Page TIFF
Choose between single- and multiple‑page TIFF files.
Set the compression for TIFF files.
Enable the Text/Photo mode to have smaller file sizes by using 1‑bit image.
1 bit 8 bit*
Turn on scanning of custom jobs by default.
Show a preview of the scan on the display.
1–9999 (1*) Set the number of copies.
Set the paper source for the print job.
Tray [x] (1*) Multipurpose Feeder Manual Paper Manual Envelope
Print multiple copies in sequence.

Understanding the printer menus 118
Specify whether to print on one side or two sides of the paper.
1‑Sided* 2‑Sided
Determine which side of the paper (long edge or short edge) is bound when performing two‑sided printing.
Long Edge* Short Edge
Print multiple page images on one side of a sheet of paper.
Off* [n] pages per side
Pages per Side Ordering
Specify the positioning of multiple page images when using Pages per Side.
Horizontal* Reverse Horizontal Reverse Vertical Vertical
Pages per Side Orientation
Specify the orientation of a multiple‑page document when using Pages per Side.
Pages per Side Border
Print a border around each page image when using Pages per Side.
Specify whether to insert blank separator sheets when printing.
Off* Between Copies Between Jobs Between Pages
Specify the paper source for the separator sheet.
Tray [x] (1*) Multipurpose Feeder
Specify whether to print blank pages in a print job.
Do Not Print* Print

Understanding the printer menus 119
Specify how a network is connected.
Auto* Standard Network Wireless
Network Status Show the connection status of the printer network.
Display Network Status on Printer
Show the network status on the display.
Speed, Duplex Show the speed of the currently active network card.
IPv4 Show the IPv4 address.
All IPv6 Addresses Show all IPv6 addresses.
Reset Print Server Reset all active network connections to the printer.
Set the time before the printer cancels a network print job.
Off On* (90 seconds)
Print a banner page.
Scan to PC Port Range
9751:12000* Specify a valid port range for printers that are behind a port blocking firewall.
Setup Using Mobile App Configure the Wi‑Fi connection using Lexmark Mobile Assistant.

Understanding the printer menus 120
Configure the Wi‑Fi connection using the control panel.
Setup On Printer Panel
Choose Network Add Wi‑Fi Network
Network Name Network Mode
Infrastructure Wireless Security Mode
Disabled* WEP WPA2/WPA - Personal WPA2 - Personal 802.1x - RADIUS
Wi‑Fi Protected Setup
Establish a Wi‑Fi network and enable network security.
Start Push Button Method Start PIN Method
Set the network mode.
Enable Wi‑Fi Direct
Enable Wi-Fi Direct‑capable devices to connect directly to the printer.
Specify the standard for the Wi‑Fi network.
802.11b/g/n (2.4GHz)* 802.11a/b/g/n/ac (2.4GHz/5GHz) 802.11a/n/ac (5GHz)
Set the security mode for connecting the printer to Wi‑Fi devices.
Disabled* WEP WPA2/WPA-Personal WPA2-Personal 802.1x - RADIUS
Set the type of Wireless Encryption Protocol (WEP) for the printer.
Set WEP Key Specify a WEP password for secure Wi‑Fi connection.

Understanding the printer menus 121
Enable Wi‑Fi security through Wi-Fi Protected Access (WPA).
Set Pre‑Shared Key Set the password for secure Wi‑Fi connection.
Enable Wi‑Fi security through WPA2.
802.1x Encryption Mode WPA+ WPA2*
Enable Wi‑Fi security through 802.1x standard.
Enable Dynamic Host Configuration Protocol (DHCP) and configure static IP address.
On* Off Set Static IP Address
IP Address Netmask Gateway
Enable and configure IPv6 settings in the printer.
On* Off Enable DHCPv6
On Off* Stateless Address Autoconfiguration
On* Off DNS Server Address Manually Assigned IPv6 Address Manually Assigned IPv6 Router Address Prefix All IPv6 Addresses All IPv6 Router Addresses
View the network addresses.

Understanding the printer menus 122
Set the printer to switch automatically to PCL emulation when a print job requires it, regardless of the default printer language.
Set the printer to switch automatically to PS emulation when a print job requires it, regardless of the default printer language.
Temporarily store print jobs in the printer hard disk before printing.
Set the printer to process Macintosh binary PostScript print jobs.
Network Speed Show the speed of an active network adapter.
Enable Dynamic Host Configuration Protocol (DHCP).
Set the static IP address of your printer.
Set Static IP Address
IP Address Netmask Gateway
Enable IPv6 in the printer.
Enable DHCPv6 in the printer.

Understanding the printer menus 123
Set the network adapter to accept the automatic IPv6 address configuration entries provided by a router.
Specify the DNS server address.
Assign the IPv6 address.
Manually Assigned IPv6 Address
Assign the IPv6 address.
Manually Assigned IPv6 Router
Specify the address prefix.
Show all IPv6 addresses.
Show all IPv6 router addresses.
All IPv6 Router Addresses
Show the printer Media Access Control (MAC) addresses: Locally Administered Address (LAA) and Universally Administered Address (UAA).
Set the printer to switch automatically to PCL emulation when a print job requires it, regardless of the default printer language.
Set the printer to switch automatically to PS emulation when a print job requires it, regardless of the default printer language.
Temporarily store jobs on the printer hard disk before printing.
Set the printer to process Macintosh binary PostScript print jobs.

Understanding the printer menus 124
Reduce power consumption when the printer does not receive data from the Ethernet network.
Set Hostname Set the current TCP/IP host name.
Domain Name Set the domain name.
Allow DHCP/BOOTP to update NTP server
Allow the DHCP and BOOTP clients to update the NTP settings of the printer.
Zero Configuration Name Specify a service name for the zero configuration network.
Assign an IP address automatically.
DNS Server Address Specify the current Domain Name System (DNS) server address.
Backup DNS Address Specify the backup DNS server addresses.
Backup DNS Address 2
Backup DNS Address 3
Domain Search Order Specify a list of domain names to locate the printer and its resources that reside in different domains on the network.
Update the Dynamic DNS settings.
300‑31536000 (3600*) Specify the current DDNS settings.
5‑254 (254*)
300‑31536000 (604800*)
Update multicast DNS settings.

Understanding the printer menus 125
WINS Address Specify a server address for Windows Internet Name Service (WINS).
Allow the BOOTP to assign a printer IP address.
Restricted Server List Specify an IP address for the TCP connections.
Restricted Server List Options
Specify how the IP addresses in the list can access the printer functionality.
Block All Ports* Block Printing Only Block Printing and HTTP Only
256‑1500 (1500*) Specify a maximum transmission unit (MTU) parameter for the TCP connections.
1–65535 (9100*) Specify a raw port number for printers connected on a network.
Outbound Traffic Maximum Speed
Enable the printer maximum transfer rate.
Enable the SSLv2 protocol.
Enable the SSLv3 protocol.
Enable TLSv1.0
Enable the TLSv1.0 protocol.
Enable TLSv1.1
Enable the TLSv1.1 protocol.
SSL Cipher List Specify the cipher algorithms to use for the SSL or the TLS connections.

Understanding the printer menus 126
SNMP Versions 1 and 2c
Configure Simple Network Management Protocol (SNMP) versions 1 and 2c to install print drivers and applications.
Off On* Allow SNMP Set
Off On* Enable PPM MIB
Off On* SNMP Community
Configure SNMP version 3 to install and update the printer security.
Off On* Set Read/Write Credentials
User Name Password Set Read‑only Credentials
User Name Password Authentication Hash
MD5 SHA1* Minimum Authentication Level
No Authentication, No Privacy Authentication, No Privacy Authentication, Privacy* Privacy Algorithm
Enable Internet Protocol Security (IPSec).

Understanding the printer menus 127
Set the IPSec base configuration.
DH (Diffie‑Hellman) Group Proposal
Set the IPSec encryption.
modp2048 (14)* modp3072 (15) modp4096 (16) modp6144 (17)
Specify the encryption and authentication methods to connect to a network securely.
IKE SA Lifetime (Hours)
Set the amount of time before a new authentication key is generated.
1 2 4 8 24*
IPSec SA Lifetime (Hours)
1 2 4 8* 24
IPSec Device Certificate Specify an IPSec certificate.
Pre‑Shared Key Authenticated Connections
Configure the authenticated connections of the printer.

Understanding the printer menus 128
Let the printer join networks that require authentication before allowing access.
0–65535 seconds (90*) Set the time‑out value to stop the Line Printer Daemon (LPD) server from waiting indefinitely for hung or invalid print jobs.
Print a banner page for all LPD print jobs.
Print a trailer page for all LPD print jobs.
LPD Carriage Return Conversion
Enable carriage return conversion.
Access the Embedded Web Server to monitor and manage the printer.
Configure the Hypertext Transfer Protocol Secure (HTTPS) settings.

Understanding the printer menus 129
Force the printer to use the HTTPS connections.
Send files using FTP.
Local Domains Specify domain names for HTTP and FTP servers.
HTTP Proxy IP Address Configure the HTTP and FTP server settings.
HTTP Default IP Port
FTP Default IP Port
Timeout for HTTP/FTP Requests
Specify the amount of time before the server connection stops.
Retries for HTTP/FTP Requests
1–299 (3*) Set the number of retries to connect to the HTTP/FTP server.
Print using ThinPrint.
4000–4999 (4000*) Set the port number for the ThinPrint server.
100–1000000 (0*) Set the speed to transmit data in a ThinPrint environment.
0–64000 (0*) Set the packet size for data transmission.

Understanding the printer menus 130
Set the printer to switch to PCL emulation when a print job received through a USB port requires it, regardless of the default printer language.
Set the printer to switch to PS emulation when a print job received through a USB port requires it, regardless of the default printer language.
Temporarily store jobs on the printer hard disk before printing.
Set the printer to process Macintosh binary PostScript print jobs.
Enable the standard USB port.
Register the printer to the Google Cloud Print server.
Print directly from your Google account.
Enable Google Cloud Print
Allow the registered user and other users on the same subnet to send jobs to the printer locally.

Understanding the printer menus 131
Verify authenticity of the peer certificate to connect to your Google account.
Enable SSL Peer Verification
Set the printer to process PDF files as an image for faster printing.
Always Print As Image
SSID Specify the service set identifier (SSID) of the Wi‑Fi network.
Set Preshared Key Set the preshared key (PSK) to authenticate and validate users on a Wi‑Fi connection.
Show PSK on Setup Page
Show the PSK on the Network Setup Page.
Group Owner IP Address Specify the IP address of the group owner.
Auto‑Accept Push Button Requests
Accept requests to connect to the network automatically.

Understanding the printer menus 132
Control access to the printer functions.
Access Address Book in Apps Modify Address Book Manage Shortcuts Create Profiles Manage Bookmarks Flash Drive Print Flash Drive Color Printing Flash Drive Scan Copy Function Copy Color Printing Color Dropout E‑mail Function Fax Function FTP Function Release Held Faxes Held Jobs Access User Profiles Cancel Jobs at the Device Change Language Internet Printing Protocol (IPP) Initiate Scans Remotely B/W Print Color Print
Control access to the printer menu settings.
Security Menu Network/Ports Menu Paper Menu Reports Menu Function Configuration Menus Supplies Menu Option Card Menu SE Menu Device Menu
Menu item Description · Function Access · Administrative Menus

Understanding the printer menus 133
Control access to the printer management options.
Remote Management Firmware Updates Apps Configuration Operator Panel Lock Import/Export All Settings Out of Service Erase
Control access to printer applications.
New Apps Card Copy Scan Center Scan Center Custom 1 Scan Center Custom 2 Scan Center Custom 3 Scan Center Custom 4 Scan Center Custom 5 Scan Center Custom 6 Scan Center Custom 7 Scan Center Custom 8 Scan Center Custom 9 Scan Center Custom 10 Forms and Favorites
Control group or user access to the printer functions, applications, and security settings.
Function Access Administrative Menus Device Management Apps All Users
Function Access Administrative Menus Device Management Apps Admin

Understanding the printer menus 134
Create local accounts to manage access to the printer functions.
User Name/Password User Name Password PIN
Specify the default login method to access the control panel.
User Name/Password User Name Password PIN
Specify the default login method to access the browser.
User Name/Password User Name Password PIN
Schedule access to the USB ports.

Understanding the printer menus 135
Record the events in the secure audit log and remote syslog.
Send audit logs to a remote server.
Remote Syslog Server Specify the remote syslog server.
1–65535 (514*) Specify the remote syslog port.
Specify a syslog method to transmit logged events to a remote server.
Specify a facility code that the printer uses when sending log events to a remote server.
0 ‑ Kernel Messages 1 ‑ User‑Level Messages 2 ‑ Mail System 3 ‑ System Daemons 4 ‑ Security/Authorization Messages* 5 ‑ Messages Generated Internally by Syslogs 6 ‑ Line Printer Subsystem 7 ‑ Network News Subsystem 8 ‑ UUCP Subsystem 9 ‑ Clock Daemon 10 ‑ Security/Authorization Messages 11 ‑ FTP Daemon 12 ‑ NTP Subsystem 13 ‑ Log Audit 14 ‑ Log Alert 15 ‑ Clock Daemon 16 ‑ Local Use 0 (local0) 17‑ Local Use 1 (local1) 18 ‑ Local Use 2 (local2) 19 ‑ Local Use 3 (local3) 20 ‑ Local Use 4 (local4) 21 ‑ Local Use 5 (local5) 22 ‑ Local Use 6 (local6) 23 ‑ Local Use 7 (local7)

Understanding the printer menus 136
Severity of Events to Log
Specify the priority level cutoff for logging messages and events.
0 ‑ Emergency 1 ‑ Alert 2 ‑ Critical 3 ‑ Error 4 ‑ Warning* 5 ‑ Notice 6 ‑ Informational 7 ‑ Debug
Remote Syslog Non‑Logged Events
Send all events, regardless of severity level, to the remote server.
Admin’s E‑mail Address Send e‑mail notification of logged events to the administrator.
E‑mail Log Cleared Alert
Send e‑mail notification to the administrator when a log entry is deleted.
E‑mail Log Wrapped Alert
Send e‑mail notification to the administrator when the log becomes full and begins to overwrite the oldest entries.
Resolve log storage issues when the log fills its allotted memory.
Wrap Over Older Entries* E‑mail Log Then Delete All Entries
E‑mail % Full Alert
Send e‑mail notification to the administrator when the log fills its allotted memory.
% Full Alert Level
E‑mail Log Exported Alert
Send e‑mail notification to the administrator when a log is exported.
E‑mail Log Settings Changed Alert
Send e‑mail notification to the administrator when Enable Audit is set.
Specify how the log file terminates the end of each line.
LF (\n)* CR (\r) CRLF (\r\n)

Understanding the printer menus 137
Add a digital signature to each exported log file.
Clear Log Delete all audit logs.
Export a security log to a flash drive.
Syslog (RFC 5424) Syslog (RFC 3164) CSV
1–10 (3*) Specify the number of failed login attempts before the user gets locked out.
1–60 minutes (5*) Specify the time frame between failed login attempts before the user gets locked out.
1–60 minutes (5*) Specify the lockout duration.
1–120 minutes (10*) Specify the delay for a remote login before the user is logged off automatically.
2–10 Set the number of times an invalid PIN can be entered.
Set the expiration time for confidential print jobs.
Off* 1 Hour 4 Hours 24 Hours 1 Week

Understanding the printer menus 138
Set the expiration time for a print job that you want to repeat.
Off* 1 Hour 4 Hours 24 Hours 1 Week
Set the expiration time that the printer prints a copy for the user to examine its quality, before printing the remaining copies.
Off* 1 Hour 4 Hours 24 Hours 1 Week
Set the expiration time that the printer stores print jobs for printing later.
Off* 1 Hour 4 Hours 24 Hours 1 Week
Require All Jobs to be Held
Set the printer to hold all print jobs.
Set the printer to print other documents with the same file name without overwriting any of the print jobs.
Search the different servers in the domain for the logged-in user account.
Enable verification of LDAP certificates.

Understanding the printer menus 139
Determine whether Disk Encryption is enabled.
Start encryption Prevent the loss of sensitive data in case the printer or its hard disk is stolen.
Stored in onboard memory
Delete all files stored on the printer memory.
Enable AirPrint printing.
Show all the features that Function Access Control (FAC) protects regardless of the security permission that the user has.
Let the user log in before printing.
Default Print Permission Login Set the default login for Print Permission.

Understanding the printer menus 140
Specify the effect of using the security reset jumper.
Enable “Guest” access* No Effect
0–32 (0*) Specify the minimum characters that are allowed for a password.
Menu Settings Page Print a report that contains the printer preferences, settings, and configurations.
Device Information Print a report that contains information about the printer.
Device Statistics Print a report about printer usage and supply status.
Profile List Print a list of profiles that are stored in the printer.
Asset Report Print a report that contains the printer serial number and model name.
Print samples and information about the fonts that are available in each printer language.
PCL Fonts PS Fonts
Print Directory Print the resources that are stored in the flash drive or printer hard disk.

Understanding the printer menus 141
All Shortcuts Print a report that lists the shortcuts that are stored in the printer.
E‑mail Shortcuts
Fax Job Log Print a report about the last 200 completed fax jobs.
Fax Call Log Print a report about the last 100 attempted, received, and blocked calls.
Network Setup Page Print a page that shows the configured network and wireless settings on the printer.
Print All Guides Prints all the guides
Connection Guide Provides information about connecting the printer locally (USB) or to a network
Copy Guide Provides information about making copies and configuring the settings
E‑mail Guide Provides information about sending e‑mails and configuring the settings
Fax Guide Provides information about sending faxes and configuring the settings
FTP Guide Provides information about scanning documents and configuring the settings
Information Guide Provides more information sources about the printer
Media Guide Provides information about loading paper and specialty media
Mono Quality Guide Provides information about mono print quality settings

Understanding the printer menus 142
Moving Guide Provides information about moving, locating, or shipping the printer
Print Quality Guide Provides information about solving print quality issues
Supplies Guide Provides information about ordering supplies
Print Quality Test Pages Print sample pages to identify and correct print quality defects.
From the home screen, touch Settings > Reports > Menu Settings Page.
Menu item Description · Menu item Description

Securing the printer 143
Locating the security slot
The printer is equipped with a security lock feature. Attach a security lock compatible with most laptop computers in the location shown to secure the printer in place.

To erase volatile memory or buffered data in your printer, turn off the printer.
To erase non‑volatile memory or individual settings, device and network settings, security settings, and embedded solutions, do the following:
1 From the home screen, touch Settings > Device > Maintenance > Out of Service Erase.
2 Select the Sanitize all information on nonvolatile memory check box, and then touch ERASE.
3 Follow the instructions on the display.
1 From the home screen, touch Settings > Device > Maintenance > Out of Service Erase.
2 Select the Sanitize all information on hard disk check box, and then touch ERASE.
3 Follow the instructions on the display.
This process erases all contents in the hard disk. If necessary, back up important data from the printer before starting the encryption.
1 From the home screen, touch Settings > Security > Disk Encryption > Start encryption.
2 Follow the instructions on the display.

Securing the printer 144
From the home screen, touch Settings > Device > Restore Factory Defaults > Restore Settings > Restore all settings > RESTORE > Start.
For more information, see “Erasing printer memory” on page 143.
Type of memory Description
Volatile memory The printer uses standard random access memory (RAM) to buffer temporarily user data during simple print and copy jobs.
Non-volatile memory The printer may use two forms of non-volatile memory: EEPROM and NAND (flash memory). Both types are used to store the operating system, printer settings, network information, scanner and bookmark settings, and embedded solutions.
Hard disk memory Some printers may have a hard disk drive installed. The printer hard disk is designed for printer-specific functionality. The hard disk lets the printer retain buffered user data from complex print jobs, form data, and font data.
Erase the content of any installed printer memory in the following circumstances:

Maintaining the printer 145
The speaker volume will reset to default value after the session is logged out, when the printer wakes from Sleep or Hibernate mode, or after a power‑on reset.
1 From the control panel, navigate to:
Settings > Device > Preferences > Audio Feedback
2 Select the volume.
1 From the home screen, touch Settings > Fax > Analog Fax Setup > Speaker Settings.
1 From the home screen, navigate to:
Settings > Network/Ports > Wireless
2 Select Setup On Printer Panel and then follow the instructions on the display.

Maintaining the printer 146
1 Depending on your mobile device, download the Lexmark Mobile Assistant application from either the Google Play store or App Store online store.
2 From the control panel, navigate to:
Settings > Network/Ports > Wireless > Setup Using Mobile App > Continue for Printer ID
3 From your mobile device, launch the application, and then accept the Terms of Use.
4 Grant permissions.
5 Tap Start Wi-Fi Setup, and then select the printer.
6 Select a Wi-Fi network, and then enter your credentials.
7 Tap Finish Wi-Fi Setup.
Connecting the printer to a wireless network using Wi‑Fi Protected Setup (WPS)
Before you begin, make sure that:
1 From the control panel, navigate to:
Settings > Network/Ports > Wireless > Wi‑Fi Protected Setup > Start Push Button Method
2 Follow the instructions on the display.
1 From the control panel, navigate to:
Settings > Network/Ports > Wireless > Wi‑Fi Protected Setup > Start PIN Method
2 Copy the eight‑digit WPS PIN.
3 Open a Web browser, and then type the IP address of your access point in the address field.
4 Access the WPS settings. For more information, see the documentation that came with your access point.
5 Enter the eight‑digit PIN, and then save the changes.

Maintaining the printer 147
1 Open the printers folder.
2 From the shortcut menu of the printer with the new ISP, open the printer properties.
3 Configure the port from the list.
4 Update the IP address.
5 Apply the changes.
1 From System Preferences in the Apple menu, navigate to the list of printers, and then select + > IP.
2 Type the IP address in the address field.
3 Apply the changes.
1 From the home screen, touch Settings > Network/Ports > Network Overview > Active Adapter > Standard Network.
2 Follow the instructions on the display.
1 Set the parameters in the printer. a From the control panel, navigate to the menu for the port settings. b Locate the menu for the serial port settings, and then adjust the settings, if necessary.
c Apply the changes.
2 From your computer, open the printers folder, and then select your printer.
3 Open the printer properties, and then select the COM port from the list.
4 Set the COM port parameters in Device Manager.

Maintaining the printer 148
1 Turn off the printer, and then unplug the power cord from the electrical outlet.
2 Remove paper from the standard bin and multipurpose feeder.
3 Remove any dust, lint, and pieces of paper around the printer using a soft brush or vacuum.
4 Wipe the outside of the printer with a damp, soft, lint‑free cloth.
5 Connect the power cord to the electrical outlet, and then turn on the printer.
1 Open the scanner cover.


Maintaining the printer 149
2 Using a damp, soft, lint-free cloth, wipe the following areas: • ADF glass





Maintaining the printer 150
3 Open door E.

4 Using a damp, soft, lint-free cloth, wipe the following areas: • ADF glass pad in door E


5 Close door E, and then close the scanner cover.

Maintaining the printer 151
To order parts and supplies in the U.S., contact Lexmark at 1-800-539-6275 for information about Lexmark authorized supplies dealers in your area. In other countries or regions, go to www.lexmark.com or contact the place where you purchased the printer.
1 From the home screen, touch Status/Supplies.
2 Select the parts or supplies that you want to check.
Your Lexmark printer is designed to function best with genuine Lexmark parts and supplies. Use of third-party supplies or parts may affect the performance, reliability, or life of the printer and its imaging components. It can also affect warranty coverage. Damage caused by the use of third-party parts and supplies is not covered by the warranty. All life indicators are designed to function with Lexmark parts and supplies, and may deliver unpredictable results if third-party parts and supplies are used. Imaging component usage beyond the intended life may damage your Lexmark printer or its associated components.
Item United States and
Asia Pacific Latin America
Rest of Europe, Middle East,
Return Program toner cartridge
High yield Return Program toner cartridge
1 Available only for contract‑managed printers. For more information, contact your Lexmark representative or system administrator.
2 Supported only in Lexmark MX722 and MX725 printer models.

Maintaining the printer 152

Extra high yield Corporate Return Program toner cartridge1,2
Ultra high yield Corporate Return Program toner cartridge1,2
1 Available only for contract‑managed printers. For more information, contact your Lexmark representative or system administrator.
2 Supported only in Lexmark MX722 and MX725 printer models.


Maintaining the printer 153

Asia Pacific Latin America Rest of Europe, Middle East,

1 Supported only in the Lexmark MX721 printer model.
2 Supported only in the Lexmark MB2770 printer model.
3 Supported only in Lexmark MX722 and MX725 printer models.
Extremely low print coverage for extended periods of time may cause imaging unit parts to fail before the toner exhaustion.

Item Lexmark Return Program Corporate Return Program* Regular
* This imaging unit is available only for contract‑managed printers. For more information, contact your Lexmark representative or system administrator.
To identify the supported fuser type, open door A, and then remove the toner cartridge and the imaging unit. Find the two‑digit fuser type in front of the fuser, for example, 00 or 01.

Maintaining the printer 154
Regular fuser maintenance kits
Roller maintenance kit
Printer engine roller maintenance kit

Maintaining the printer 155
ADF maintenance kit 41X2351
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Settings > Device > Notifications.
3 From the Supplies menu, click Custom Supply Notifications.
4 Select a notification for each supply item.
5 Apply the changes.
1 Open door A.

Item Part number

Maintaining the printer 156
2 Remove the used toner cartridge.

3 Unpack the new toner cartridge, and then shake it to redistribute the toner.

4 Insert the new toner cartridge.

5 Close the door.
1 Open door A.

Maintaining the printer 157
2 Remove the toner cartridge.

3 Remove the used imaging unit.

4 Unpack the new imaging unit, and then shake it to redistribute the toner.


Maintaining the printer 158

5 Remove the packing material.
6 Insert the new imaging unit.

7 Insert the toner cartridge.
8 Close the door.
1 Open door C.

Maintaining the printer 159

2 Unlock the fuser.

3 Remove the used fuser.

4 Unpack the new fuser.

Maintaining the printer 160
5 Insert the new fuser until it clicks into place.

6 Lock the fuser.

7 Close the door.

Maintaining the printer 161
1 Remove the standard bin cover.

2 Open door C.

Maintaining the printer 162
3 Unlock the hot roll fuser.

4 Remove the used hot roll fuser.

5 Unpack the new hot roll fuser.
6 Insert the new hot roll fuser until it clicks into place.

7 Lock the hot roll fuser.

8 Close the door.

Maintaining the printer 163
9 Install the standard bin cover.

1 Open door A.

Maintaining the printer 164
2 Remove the toner cartridge.
3 Remove the imaging unit.

4 Remove the used transfer roller.


Maintaining the printer 165
5 Unpack the new transfer roller.
6 Insert the new transfer roller until it clicks into place.

7 Insert the imaging unit.
8 Insert the toner cartridge.
9 Close the door.

Maintaining the printer 166
1 Remove the tray.
2 Remove the used pick roller.

3 Unpack the new pick roller.

Maintaining the printer 167
4 Install the new pick roller.

5 Insert the tray.
1 Open the multipurpose feeder.


Maintaining the printer 168
2 Remove the used pick roller.

3 Unpack the new pick roller.

Maintaining the printer 169
4 Install the new pick roller.

5 Close the multipurpose feeder.
1 Turn off the printer.
2 Open door D.

Maintaining the printer 170

3 Remove the ADF pick roller cover.

4 Remove the used ADF pick roller.


Maintaining the printer 171
5 Unpack the new ADF pick roller.
6 Insert the new ADF pick roller until it clicks into place.


Maintaining the printer 172
7 Insert the ADF pick roller cover until it clicks into place.

8 Close the door.
9 Turn on the printer.
1 Turn off the printer.
2 Open door D.

Maintaining the printer 173
3 Remove the ADF pick roller cover.
4 Remove the used ADF feed roller.

5 Unpack the new ADF feed roller.

Maintaining the printer 174
6 Insert the new ADF feed roller until it clicks into place.


Maintaining the printer 175
7 Insert the ADF pick roller cover until it clicks into place.
8 Close the door.
9 Turn on the printer.
1 Turn off the printer.
2 Open door D.

Maintaining the printer 176
3 Remove the ADF separator roller cover.

4 Remove the used ADF separator roller.

5 Unpack the new ADF separator roller.

Maintaining the printer 177
6 Insert the new ADF separator roller until it clicks into place.

7 Insert the ADF separator roller cover until it clicks into place.


Maintaining the printer 178
8 Close the door.
9 Turn on the printer.
1 Turn off the printer.
2 Open door D.
3 Remove the ADF separator roller cover.
4 Remove the ADF separator roller.

Maintaining the printer 179

5 Remove the used ADF torque limiter.

6 Unpack the new ADF torque limiter.
7 Insert the new ADF torque limiter.


Maintaining the printer 180
8 Insert the ADF separator roller until it clicks into place.
9 Insert the ADF separator roller cover until it clicks into place.

Maintaining the printer 181
10 Close the door.
11 Turn on the printer.
For shipping instructions, go to http://support.lexmark.com or contact customer support.

Maintaining the printer 182
1 From the home screen, touch Settings > Device > Power Management > Eco‑Mode.
2 Select a setting.
1 From the home screen, touch Settings > Device > Power Management > Timeouts > Sleep Mode.
2 Specify the amount of time that the printer stays idle before it enters Sleep mode.
1 From the home screen, touch Settings > Device > Power Management > Timeouts > Hibernate Timeout.
2 Select the amount of time that the printer stays idle before it enters Hibernate mode.
1 From the home screen, touch Settings > Device > Preferences > Screen Brightness.
2 Adjust the setting.
To return Lexmark products for recycling:
1 Go to www.lexmark.com/recycle.
2 Select the product you want to recycle.
Eco‑Mode

Maintaining the printer 183
Lexmark continually strives to minimize packaging. Less packaging helps to ensure that Lexmark printers are transported in the most efficient and environmentally sensitive manner and that there is less packaging to dispose of. These efficiencies result in fewer greenhouse emissions, energy savings, and natural resource savings. Lexmark also offers recycling of packaging components in some countries or regions. For more information, go to www.lexmark.com/recycle, and then choose your country or region. Information on available packaging recycling programs is included with the information on product recycling.
Lexmark cartons are 100% recyclable where corrugated recycling facilities exist. Facilities may not exist in your area.
The foam used in Lexmark packaging is recyclable where foam recycling facilities exist. Facilities may not exist in your area.
When you return a cartridge to Lexmark, you can reuse the box that the cartridge came in. Lexmark recycles the box.
The Lexmark Cartridge Collection Program allows you to return used cartridges for free to Lexmark for reuse or recycling. One hundred percent of the empty cartridges returned to Lexmark are either reused or demanufactured for recycling. The boxes used to return the cartridges are also recycled.
To return Lexmark cartridges for reuse or recycling, do the following:
1 Go to www.lexmark.com/recycle.
2 Select the product that you want to recycle.

Avoiding jams
Correct loading of paper Incorrect loading of paper



Clearing jams 184


Clearing jams 185

6 Automatic document feeder
1 Remove the tray.

2 Remove the jammed paper.

3 Insert the tray.
1 Open door A.

2 Remove the toner cartridge.
3 Remove the imaging unit.

Clearing jams 187

4 Pull out the duplex unit.

5 Remove the jammed paper.

6 Insert the duplex unit.
Clearing jams 188

7 Insert the imaging unit.
8 Insert the toner cartridge.
9 Close the door.
1 Open door C.
2 Remove the jammed paper from any of the following areas:
Clearing jams 189




3 Close the door.
Remove the jammed paper.
Clearing jams 190


1 Remove paper from the multipurpose feeder.

2 Remove the jammed paper.
3 Flex, fan, and align the paper edges before loading.
4 Reload paper.

Clearing jams 191

1 Remove all original documents from the ADF tray.
2 Open door D.
3 Remove the jammed paper.

4 Close door D.
5 Open the scanner cover.
Clearing jams 192

6 Open door E.

7 Remove the jammed paper.

8 Close door E, and then close the scanner cover.
Clearing jams 193

Network connection problems
Step 1 Check if you are using a supported browser:
Go to step 2. Install a supported browser.
Is your browser supported?
Go to step 3. Type the correct printer IP address in the address field.
Make sure that the printer IP address is correct.
View the printer IP address:
Is the printer IP address correct?
Go to step 4. Turn on the printer.
Check if the printer is on.
Is the printer on?
Step 4 Check if the network connection is working.
Go to step 5. Contact your administrator.
Is the network connection working?
Go to step 6. Secure the cable connections.
Make sure that the cable connections to the printer and print server are secure.
For more information, see the setup documentation that came with the printer.
Are the cable connections secure?

Go to step 7. Contact your administrator.
Check if the web proxy servers are disabled.
Are the web proxy servers disabled?
Step 7 Access the Embedded Web Server.
The problem is solved.
Contact customer support.
Did the Embedded Web Server open?
Go to step 2. Wait for the printer to finish processing the other job.
Check if the printer is not busy processing another print, copy, scan, or fax job.
Is the printer ready?
Go to step 3. Insert the flash drive into the correct port.
Check if the flash drive is inserted into the front USB port.
Is the flash drive inserted into the correct port?
Go to step 4. Insert a supported flash drive.
Check if the flash drive is supported. For more information, see “Supported flash drives and file types” on page 43.
Is the flash drive supported?
The problem is solved.
Contact customer support.
a Check if the USB port is enabled. For more information, see
“Enabling the USB port” on page 195. b Remove, and then insert the flash drive.
Does the printer recognize the flash drive?
From the home screen, touch Settings > Network/Ports > USB > Enable USB Port.

1 From the home screen, touch Settings > Reports > Network > Network Setup Page.
2 Check the first section of the network setup page, and confirm that the status is connected.
If the status is not connected, then the LAN drop may be inactive, or the network cable may be malfunctioning. Contact your administrator for assistance.
Step 1 Turn off the printer, wait for about 10 seconds, and then turn on the printer.
The problem is solved.
Go to step 2.
Does the internal option operate correctly?
Step 2 Print the Menu Settings Page, and then check if the internal option appears in the Installed Features list.
Go to step 4. Go to step 3.
Is the internal option listed in the menu settings page?
The problem is solved.
Go to step 4.
Check if the internal option is installed properly into the controller board.
a Turn off the printer, and then unplug the power cord from the
electrical outlet. b Make sure that the internal option is installed in the appropriate
connector in the controller board. c Connect the power cord to the electrical outlet, and then turn
on the printer.
Does the internal option operate correctly?
Troubleshooting 196 · Action Yes No · Step 3

The problem is solved.
Contact customer support.
a Check if the internal option is available in the print driver.
Does the internal option operate correctly?
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
To correct this problem, purchase a cartridge with the correct region that matches the printer region, or purchase a worldwide cartridge.
Troubleshooting 197 · Action Yes No · Step 4

Worldwide or Undefined region 0
North America (United States, Canada) 1
European Economic Area, Western Europe, Nordic countries, Switzerland 2
Rest of Europe, Middle East, Africa 5
Australia, New Zealand 6
The printer has detected a non‑Lexmark supply or part installed in the printer.
Your Lexmark printer is designed to function best with genuine Lexmark supplies and parts. Use of third- party supplies or parts may affect the performance, reliability, or life of the printer and its imaging components.
All life indicators are designed to function with Lexmark supplies and parts and may deliver unpredictable results if third-party supplies or parts are used. Imaging component usage beyond the intended life may damage your Lexmark printer or associated components.
To accept any and all of these risks and to proceed with the use of non-genuine supplies or parts in your printer, from the control panel, press and hold X and # simultaneously for 15 seconds.
If you do not want to accept these risks, then remove the third-party supply or part from your printer and install a genuine Lexmark supply or part. For more information, see “Using genuine Lexmark parts and supplies” on page 151.
If the printer does not print after pressing and holding X and # simultaneously for 15 seconds, then reset the supply usage counter.
1 From the control panel, navigate to:
Settings > Device > Maintenance > Configuration Menu > Supply Usage And Counters
2 Select the part or supply that you want to reset, and then select Start.
3 Read the warning message, and then select Continue.
4 Press and hold X and # simultaneously for 15 seconds to clear the message.

Go to step 2. The problem is solved.
a Use an envelope that has been stored in a dry environment.
Does the envelope seal when printing?
Contact customer support.
The problem is solved.
a Make sure that paper type is set to Envelope.
From the control panel, navigate to: Settings > Paper > Tray Configuration > Paper Size/Type b Send the print job.
Does the envelope seal when printing?
The problem is solved.
Go to step 2.
a From the home screen, touch Settings > Print > Layout >
Collate. b Set Collate to On.
c Print the document.
Are the pages collated correctly?
The problem is solved.
Go to step 3.
a From the document that you are trying to print, open the Print
dialog, and then select Collate. b Print the document.
Are the pages collated correctly?
The problem is solved.
Contact customer support.
a Reduce the number of pages to print. b Print the document.
Are the pages collated correctly?

The problem is solved.
Go to step 2.
a Check if the trays contain the same paper size and paper type. b Check if the paper guides are positioned correctly.
c Print the document.
Do the trays link correctly?
The problem is solved.
Go to step 3.
a From the control panel, navigate to:
Settings > Paper > Tray Configuration > Paper Size/Type b Set the paper size and paper type to match the paper loaded
in the linked trays. c Print the document.
Do the trays link correctly?
The problem is solved.
Contact customer support.
a Make sure that Tray Linking is set toAutomatic. For more
information, see “Linking trays” on page 35. b Print the document.
Do the trays link correctly?
Go to step 2. The problem is solved.
a Remove the tray. b Check if paper is loaded correctly.
Do paper jams occur frequently?

Go to step 3. The problem is solved.
a From the control panel, navigate to:
Settings > Paper > Tray Configuration > Paper Size/Type b Set the correct paper size and type.
c Print the document.
Do paper jams occur frequently?
Contact customer support.
The problem is solved.
a Load paper from a fresh package.
Do paper jams occur frequently?
a From the home screen, touch Settings > Device > Notifications
The problem is solved.
Contact customer support.
> Jam Content Recovery. b Select On or Auto.
c Apply the changes.
Are the jammed pages reprinted?

Settings > Troubleshooting > Print Quality Test Pages. For non‑touch‑screen printer models, press to navigate through the settings.

Go to step 2. The problem is solved.
a Check if the printer is using a genuine and supported Lexmark
toner cartridge.
Is the printer printing blank or white pages?
Go to step 3. The problem is solved.
a Remove any packing material that is left on the imaging unit.
1 Remove the toner cartridge, and then remove the imaging unit.
Is the printer printing blank or white pages?
Go to step 5. Go to step 4.
Check the transfer roller for proper installation.
Is the transfer roller installed properly?
Go to step 5. The problem is solved.
a Remove, and then insert the transfer roller. b Print the document.
Is the printer printing blank or white pages?
Contact customer support.
The problem is solved.
a Replace the imaging unit. b Print the document.
Is the printer printing blank or white pages?


Settings > Troubleshooting > Print Quality Test Pages. For non‑touch‑screen printer models, press to navigate through the settings.
Go to step 2. The problem is solved.
a Check if the printer is using a genuine and supported Lexmark
toner cartridge.
Is the print dark?
Go to step 3. The problem is solved.
a Turn off the printer, wait for about 10 seconds, and then turn on
the printer. b Reduce toner darkness. From the control panel, navigate to:
Settings > Print > Quality c Print the document.
Is the print dark?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type
from the Printing Preferences or Print dialog.
Is the print dark?
Step 4 Check if the paper has texture or rough finishes.
Go to step 5. Go to step 6.
Are you printing on textured or rough paper?

Go to step 6. The problem is solved.
a Replace textured paper with plain paper. b Print the document.
Is the print dark?
Go to step 7. The problem is solved.
a Load paper from a fresh package.
Is the print dark?
Go to step 8. The problem is solved.
a Remove, and then insert the imaging unit.
Is the print dark?
Contact customer support.
The problem is solved.
a Replace the imaging unit. b Print the document.
Is the print dark?

Settings > Troubleshooting > Print Quality Test Pages. For non‑touch‑screen printer models, press to navigate through the settings.

Go to step 2. The problem is solved.
a Check if the printer is using a genuine and supported Lexmark
toner cartridge.
Are fine lines not printed correctly?
Contact customer support.
The problem is solved.
a Adjust the print quality settings.
1 From the control panel, navigate to: Settings > Print > Quality > Pixel Boost > Fonts 2 Adjust Toner Darkness to 7. From the control panel, navigate to: Settings > Print > Quality b Print the document.
Are fine lines not printed correctly?

Settings > Troubleshooting > Print Quality Test Pages. For non‑touch‑screen printer models, press to navigate through the settings.
Go to step 2. The problem is solved.
a Check if the printer is using a genuine and supported Lexmark
toner cartridge.
Is the paper folded or wrinkled?

Go to step 3. The problem is solved.
a Load paper from a fresh package.
Is the paper folded or wrinkled?
Contact customer support.
The problem is solved.
a Depending on your operating system, specify the paper type
from the Printing Preferences or Print dialog.
Is the paper folded or wrinkled?

Settings > Troubleshooting > Print Quality Test Pages. For non‑touch‑screen printer models, press to navigate through the settings.
Go to step 2. The problem is solved.
a Turn off the printer, wait for 10 seconds, and then turn on the
printer. b Decrease toner darkness.
From the control panel, navigate to:
Settings > Print > Quality c Print the document.
Does gray background appear on prints?

Go to step 3. The problem is solved.
a Check if the printer is using a genuine and supported Lexmark
toner cartridge.
Does gray background appear on prints?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type
from the Printing Preferences or Print dialog.
Does gray background appear on prints?

Go to step 5. The problem is solved.
a Remove the imaging unit.

Does gray background appear on prints?
Contact customer support.
The problem is solved.
a Replace the imaging unit. b Print the document.
Does gray background appear on prints?


The problem is solved.
Go to step 2.
a Adjust the paper guides to the correct position for the paper
loaded. b Print the document.
Are the margins correct?
The problem is solved.
Contact customer support.
a Depending on your operating system, specify the paper size
from the Printing Preferences or Print dialog.
Are the margins correct?

Settings > Troubleshooting > Print Quality Test Pages. For non‑touch‑screen printer models, press to navigate through the settings.

Go to step 2. The problem is solved.
a Check if the printer is using a genuine and supported Lexmark
toner cartridge.
Is the print light?
Go to step 3. The problem is solved.
a Turn off the printer, wait for about 10 seconds, and then turn on
the printer. b Increase toner darkness. From the control panel, navigate to:
Settings > Print > Quality c Print the document.
Is the print light?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type
from the Printing Preferences or Print dialog.
Is the print light?
Go to step 5. The problem is solved.
Check if the print resolution is set to 600 dpi.
a From the control panel, navigate to:
Settings > Print > Quality > Print Resolution b Print the document.
Is the print light?

Go to step 6. The problem is solved.
a Remove the toner cartridge, and then remove the imaging unit.
c Firmly shake the imaging unit to redistribute the toner, and then
insert it. d Insert the toner cartridge. e Turn off the printer, wait for 10 seconds, and then turn on the
printer. f Print the document.
Is the print light?
Go to step 7. The problem is solved.
a If the issue happens after installing a new maintenance kit, then
check whether the transfer roller included with the kit is installed.
Is the print light?
Step 7 Check the status of the imaging unit. From the control panel, navigate to: Status/Supplies > Supplies
Go to step 8. Contact customer support.
Is the imaging unit near end of life?
Contact customer support.
The problem is solved.
a Replace the imaging unit. b Print the document.
Is the print light?


Settings > Troubleshooting > Print Quality Test Pages. For non‑touch‑screen printer models, press to navigate through the settings.
Go to step 2. The problem is solved.
a Check if the printer is using a genuine and supported Lexmark
toner cartridge.
Is the print mottled?
Go to step 3. Contact customer support.
Check the printer for leaked toner contamination.
Is the printer free of leaked toner?
Step 3 Check the status of the imaging unit. From the control panel, navigate to: Status/Supplies > Supplies
Go to step 4. Contact customer support.
Is the imaging unit near end of life?
Contact customer support.
The problem is solved.
a Replace the imaging unit. b Print the document.
Is the print mottled?


Settings > Troubleshooting > Print Quality Test Pages. For non‑touch‑screen printer models, press to navigate through the settings.
Go to step 2. The problem is solved.
a Check if the printer is using a genuine and supported Lexmark
toner cartridge.
Is the paper curled?
Go to step 3. The problem is solved.
a Adjust the guides in the tray to the correct position for the paper
loaded. b Print the document.
Is the paper curled?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper size
and paper type from the Printing Preferences or Print dialog.
Is the paper curled?
Go to step 5. The problem is solved.
a Remove paper from the tray, and then turn over the paper. b Print the document.
Is the paper curled?

Go to step 6. The problem is solved.
a Load paper from a fresh package.
Is the paper curled?
Contact customer support.
The problem is solved.
a Check if the paper loaded is supported.
Is the paper curled?

Settings > Troubleshooting > Print Quality Test Pages. For non‑touch‑screen printer models, press to navigate through the settings.
Go to step 2. The problem is solved.
a Adjust the guides in the tray to the correct position for the paper
loaded. b Print the document.
Is the print crooked or skewed?
Go to step 3. The problem is solved.
a Check if the paper loaded is supported.
Is the print crooked or skewed?

Contact customer support.
The problem is solved.
a Check the pick tire in the tray for signs of damage and
contamination, and replace if necessary. b Print the document.
Is the print crooked or skewed?

Settings > Troubleshooting > Print Quality Test Pages. For non‑touch‑screen printer models, press to navigate through the settings.
Go to step 2. The problem is solved.
a Check if the printer is using a genuine and supported Lexmark
toner cartridge.
Is the printer printing solid black pages?
Go to step 3. The problem is solved.
a Remove, and then insert the imaging unit.
Is the printer printing solid black pages?

Go to step 4. The problem is solved.
a Remove the imaging unit.
Is the printer printing solid black pages?
Contact customer support.
Go to step 5.
Check the imaging unit for signs of damage.
Is the imaging unit free from damage?
Contact customer support.
The problem is solved.
a Replace the imaging unit. b Print the document.
Is the printer printing solid black pages?


Settings > Troubleshooting > Print Quality Test Pages. For non‑touch‑screen printer models, press to navigate through the settings.
Go to step 2. The problem is solved.
a Check if the printer is using a genuine and supported Lexmark
toner cartridge.
Are text or images cut off?
Go to step 3. The problem is solved.
a Remove, and then insert the imaging unit.
Are text or images cut off?

Go to step 4. The problem is solved.
a Remove the imaging unit.
Are text or images cut off?
Contact customer support.
The problem is solved.
a Replace the imaging unit. b Print the document.
Are text or images cut off?


Settings > Troubleshooting > Print Quality Test Pages. For non‑touch‑screen printer models, press to navigate through the settings.
Go to step 2. The problem is solved.
a Check if the printer is using a genuine and supported Lexmark
toner cartridge.
Does toner easily rub off?
Go to step 3. The problem is solved.
a Depending on your operating system, specify the paper type
from the Printing Preferences or Print dialog.
Does toner easily rub off?
Contact customer support.
The problem is solved.
a Remove, and then insert the fuser. b Print the document.
Does toner easily rub off?


Settings > Troubleshooting > Print Quality Test Pages. For non‑touch‑screen printer models, press to navigate through the settings.
Go to step 2. The problem is solved.
a Check if the printer is using a genuine and supported Lexmark
toner cartridge.
Do horizontal light bands appear on prints?
Contact customer support.
The problem is solved.
a Turn off the printer, wait for about 10 seconds, and then turn on
the printer. b Print the document.
Do horizontal light bands appear on prints?

Settings > Troubleshooting > Print Quality Test Pages. For non‑touch‑screen printer models, press to navigate through the settings.

a Check if the printer is using a genuine and supported Lexmark
Contact customer support.
The problem is solved.
toner cartridge.
Do vertical light bands appear on prints?

Settings > Troubleshooting > Print Quality Test Pages. For non‑touch‑screen printer models, press to navigate through the settings.
Go to step 2. The problem is solved.
a Check if the printer is using a genuine and supported Lexmark
toner cartridge.
Do vertical white lines appear on prints?
Go to step 3. The problem is solved.
Fix slow printing problems. For more information, see “Slow printing” on page 229.
Do vertical white lines appear on prints?
Contact customer support.
The problem is solved.
a Replace the imaging unit. b Print the document.
Do vertical white lines appear on prints?


Settings > Troubleshooting > Print Quality Test Pages. For non‑touch‑screen printer models, press to navigate through the settings.
Go to step 2. The problem is solved.
a Check if the printer is using a genuine and supported Lexmark
toner cartridge.
Do vertical dark bands appear on prints?
Go to step 3. The problem is solved.
a Remove the toner cartridge, and then remove the imaging unit.
c Print the document.
Do vertical dark bands appear on prints?

Go to step 4. The problem is solved.
a Remove the imaging unit.
Do vertical dark bands appear on prints?
Contact customer support.
The problem is solved.
a Check if a bright light enters the right side of the printer, and
move the printer if necessary. b Print the document.
Do vertical dark bands appear on prints?


Settings > Troubleshooting > Print Quality Test Pages. For non-touch-screen printer models, press to navigate through the settings.
Go to step 2. Go to step 3.
Using a blank sheet of paper, make a two‑sided copy using the ADF.
Do vertical dark lines or streaks appear on prints?
Go to step 3. The problem is solved.
Using a damp, soft, lint-free cloth, wipe the following areas:


Do vertical dark lines or streaks appear on prints?

Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type
from the Printing Preferences or Print dialog.
Do vertical dark lines or streaks appear on prints?
Go to step 5. The problem is solved.
a Load paper from a fresh package.
Do vertical dark lines or streaks appear on prints?
Contact customer support.
The problem is solved.
a Remove, and then insert the imaging kit.
Do vertical dark lines or streaks appear on prints?

Settings > Troubleshooting > Print Quality Test Pages. For non‑touch‑screen printer models, press to navigate through the settings.

Go to step 2. The problem is solved.
a Remove the imaging unit.
Do vertical dark streaks with missing images appear on prints?
Contact customer support.
The problem is solved.
a Check if the printer is using a genuine and supported Lexmark
toner cartridge.
Do vertical dark streaks with missing images appear on prints?


Settings > Troubleshooting > Print Quality Test Pages. For non‑touch‑screen printer models, press to navigate through the settings.
Go to step 2. Take note of the distance, and then contact customer support.
Using the Print Quality Test Pages, check if the distance between the repeating defects is equal to any of the following:
Does the distance between the repeating defects match any of the measurements?
Contact customer support.
The problem is solved.
a Replace the imaging unit. b Print the document.
Do the repeating defects appear?
The problem is solved.
Go to step 2.
a From the control panel, check if the documents appear in the
Held Jobs list.
Are the documents printed?

The problem is solved.
Go to step 3.
The print job may contain a formatting error or invalid data.
Are the documents printed?
Step 3 If you are printing from the Internet, then the printer may be reading the multiple job titles as duplicates.
The problem is solved.
Go to step 4.
a Open the Printing Preferences dialog. b From the Print and Hold section, select Keep duplicate
documents. c Enter a PIN. d Resend the print job.
a Save and name each job differently. b Send the job individually.
Are the documents printed?
The problem is solved.
Go to step 5.
a Delete some held jobs to free up printer memory. b Resend the print job.
Are the documents printed?
The problem is solved.
Contact customer support.
a Add printer memory. b Resend the print job.
Are the documents printed?

Go to step 2. The problem is solved.
Make sure that the printer cable is securely connected to the printer and to the computer, print server, option, or other network device.
Is the printer printing slow?
Go to step 3. The problem is solved.
a Make sure that the printer is not in Eco‑Mode or Quiet Mode.
Settings > Device > Power Management > Eco‑Mode • From the control panel, navigate to:
Settings > Device > Maintenance > Configuration Menu > Device Operations > Quiet Mode
For non‑touch‑screen printer models, press to navigate through the settings. b Print the document.
Is the printer printing slow?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the print
resolution from the Printing Preferences or Print dialog. b Set the resolution to 600 dpi.
c Print the document.
Is the printer printing slow?
Go to step 5. The problem is solved.
a From the control panel, navigate to:
Settings > Print > Quality > Print Resolution
For non‑touch‑screen printer models, press to navigate through the settings. b Set the resolution to 600 dpi.
c Print the document.
Is the printer printing slow?

Go to step 6. The problem is solved.
a Depending on your operating system, specify the paper type
from the Printing Preferences or Print dialog.
Is the printer printing slow?
Go to step 7. The problem is solved.
a Make sure that the printer settings for Texture and Weight
match the paper being loaded.
Is the printer printing slow?
Go to step 8. The problem is solved.
Remove held jobs.
Is the printer printing slow?
Go to step 9. The problem is solved.
a Make sure that the printer is not overheating.
Is the printer printing slow?
Contact customer support.
The problem is solved.
a Add more printer memory. b Print the document.
Is the printer printing slow?

The problem is solved.
Go to step 2.
a From the document that you are trying to print, open the Print
dialog, and then check if you selected the correct printer. b Print the document.
Is the document printed?
The problem is solved.
Go to step 3.
a Check if the printer is on. b Resolve any error messages that appear on the display.
c Print the document.
Is the document printed?
The problem is solved.
Go to step 4.
a Check if the ports are working, and if the cables are securely
connected to the computer and the printer.
For more information, see the setup documentation that came with the printer. b Print the document.
Is the document printed?
The problem is solved.
Go to step 5.
a Turn off the printer, wait for about 10 seconds, and then turn it
back on. b Print the document.
Is the document printed?
The problem is solved.
Contact customer support.
a Remove, and then reinstall the printer software.
Is the document printed?

The problem is solved.
Go to step 2.
Check if the power cord is connected to the electrical outlet.
Is the printer responding?
Turn on the switch or reset the breaker.
Go to step 3.
Check if the electrical outlet is turned off by a switch or breaker.
Is the electrical outlet turned off by a switch or breaker?
Go to step 4. Turn on the printer.
Check if the printer is on.
Is the printer on?
Press the power button to wake the printer.
Go to step 5.
Check if the printer is in Sleep or Hibernate mode.
Is the printer in Sleep or Hibernate mode?
Go to step 6. Insert the cables to the correct ports.
Check if the cables connecting the printer and the computer are inserted to the correct ports.
Are the cables inserted to the correct ports?
The problem is solved.
Go to step 7.
Turn off the printer, install the hardware options, and then turn on the printer.
For more information, see the documentation that came with the option.
Is the printer responding?
The problem is solved.
Go to step 8.
Install the correct print driver.
Is the printer responding?
Step 8 Turn off the printer, wait for about 10 seconds, and then turn on the printer.
The problem is solved.
Contact customer support.
Is the printer responding?

1 From the home screen, touch Settings > Print > Quality.
2 Adjust the toner darkness.
3 Apply the changes.
Go to step 2. Load the correct paper size and paper type.
a Check if you are printing on the correct paper. b Print the document.
Is the document printed on the correct paper?
The problem is solved.
Go to step 3.
a Depending on your operating system, specify the paper size
and paper type from the Printing Preferences or Print dialog.
c Print the document.
Is the document printed on the correct paper?
The problem is solved.
Contact customer support.
a Check if the trays are linked.
For more information, see “Linking trays” on page 35. b Print the document.
Is the document printed from the correct tray?

The problem is solved.
Go to step 2.
Resolve any error messages that appear on the display.
Can you send or receive a fax?
The problem is solved.
Go to step 3.
Make sure that the cable connections for the following equipment are secure:
Can you send or receive a fax?
Go to step 5. Go to step 4.
Check for a dial tone.
Can you hear a dial tone?
The problem is solved.
Go to step 5.
Check the telephone wall jack.
a Connect the analog telephone directly to the wall jack. b Listen for a dial tone.
c If you do not hear a dial tone, then use a different telephone
cable. d If you still do not hear a dial tone, then connect the analog
telephone to a different wall jack. e If you hear a dial tone, then connect the printer to that wall jack.
Can you send or receive a fax?

The problem is solved.
Go to step 6.
Check if the printer is connected to an analog phone service or to the correct digital connector.
Can you send or receive a fax?
The problem is solved.
Go to step 7.
Temporarily disconnect other equipment and disable other telephone services.
a Disconnect other equipment (such as answering machines,
computers, modems, or telephone line splitters) between the printer and the telephone line. b Disable call waiting and voice mail. For more information,
contact your telephone company.
Can you send or receive a fax?
The problem is solved.
Contact customer support.
Scan the original document one page at a time.
a Dial the fax number. b Scan the document.
Can you send or receive a fax?

The problem is solved.
Go to step 2.
Load the original document properly into the ADF tray or on the scanner glass.
Can you send faxes?
The problem is solved.
Contact customer support.
Set up the shortcut number properly.
Can you send faxes?
Step 1 Make sure that the tray or multipurpose feeder is not empty.
The problem is solved.
Go to step 2.
Can you receive faxes?
The problem is solved.
Go to step 3.
Check the ring count delay settings.
a From the home screen, touch Settings > Fax > Analog Fax
Setup > Fax Receive Settings > Rings to Answer. b If necessary, configure the setting.
Can you receive faxes?
The problem is solved.
Contact customer support.
Replace the toner cartridge. For more information, see the instruction sheet that came with the supply.
Can you receive faxes?

The problem is solved.
Go to step 2.
Make sure that there are no print quality defects.
a From the control panel, navigate to Settings > Troubleshooting
> Print Quality Test Pages. b Correct any print quality defects. For more information, see
“Print quality is poor” on page 201.
Is the fax print quality satisfactory?
Step 2 Decrease the incoming fax transmission speed.
The problem is solved.
Contact customer support.
a From the control panel, navigate to:
Settings > Fax > Analog Fax Setup > Fax Receive Settings > Admin Controls b In the Max Speed menu, select a lower transmission speed.
Is the fax print quality satisfactory?
The problem is solved.
Go to step 2.
a Turn off the printer, wait for about 10 seconds, and then turn it
back on. b Resend the scan job.
Can you send the scan job?
The problem is solved.
Contact customer support.
a Make sure that the cables between the printer and the print
server are secure. For more information, see the setup documentation that came with the printer. b Resend the scan job.
Can you send the scan job?


a Make sure that the document or photo is loaded facedown on
the upper left corner of the scanner glass. b Copy the document or photo.
a Match the paper size setting and the paper loaded in the tray. b Copy the document or photo.

a Using a damp, soft, lint-free cloth, wipe the scanner glass and
the ADF glass. b Make sure that the document or photo is loaded facedown on
the upper-left corner of the scanner glass. c Copy the document or photo.
a Check the quality of the original document or photo. b Adjust the scan quality settings.
ABCDE ABCDE ABCDE
Troubleshooting 238 · Leading edge · Trailing edge

Go to step 2. The problem is solved.
a Open the scanner cover. b Using a damp, soft, lint‑free cloth, wipe the ADF glass pad (A)
and ADF glass (B).
c Close the scanner cover.
Do vertical streaks appear on scanned documents?
Contact customer support.
The problem is solved.
a Open the scanner cover. b Using a damp, soft, lint‑free cloth, wipe the ADF glass (A) and
ADF glass pad (B) in door E.
c Close the scanner cover.
Do vertical streaks appear on scanned documents?

The problem is solved.
Go to step 2.
Check the cable connections.
a Make sure that the Ethernet or USB cable is securely connected
to the computer and the printer. b Resend the scan job.
Is the scan job successful?
The problem is solved.
Go to step 3.
Check the file you want to scan.
a Make sure that the file name is not already used in the
destination folder. b Make sure that the document or photo you want to scan is not
open in another application. c Resend the scan job.
Is the scan job successful?
The problem is solved.
Contact customer support.
a Make sure that the Append time stamp or the Overwrite
existing file check box is selected in the destination configuration settings. b Resend the scan job.
Is the scan job successful?
Remove obstructions that keep the scanner unit open.
The problem is solved.
Contact customer support.
Did the scanner unit close correctly?
Close all applications that are interfering with the scan.
Contact customer support.
The problem is solved.
Does scanning take too long or freeze the computer?

The problem is solved.
Go to step 2.
a Check if the printer is turned on. b Resolve any error messages that appear on the display.
c Copy or scan the document.
Is the scanner responding?
The problem is solved.
Go to step 3.
a Check if the power cord is connected properly to the printer
and the electrical outlet.
Is the scanner responding?
The problem is solved.
Contact customer support.
a Turn off the printer, wait for about 10 seconds, and then turn it
back on. b Copy or scan the document.
Is the scanner responding?
1 From the home screen, touch Settings > Device > Maintenance > Configuration Menu > Scanner Configuration > Scanner Manual Registration.
2 In the Print Quick Test menu, touch Start.
3 Place the Print Quick Test page on the scanner glass, and then touch Flatbed Registration.
4 In the Copy Quick Test menu, touch Start.
5 Compare the Copy Quick Test page with the original document.
6 Repeat step 4 and step 5 until the margins of the Copy Quick Test page closely match the original document.
1 From the home screen, touch Settings > Device > Maintenance > Configuration Menu > Scanner Configuration > Scanner Manual Registration.
2 In the Print Quick Test menu, touch Start.

3 Place the Print Quick Test page on the ADF tray.
4 Touch Front ADF Registration or Rear ADF Registration.
5 In the Copy Quick Test menu, touch Start.
6 Compare the Copy Quick Test page with the original document.
7 Repeat step 5 and step 6 until the margins of the Copy Quick Test page closely match the original document.
Before contacting customer support, make sure to have the following information:
Go to http://support.lexmark.com to receive e‑mail or chat support, or browse through the library of manuals, support documentation, drivers, and other downloads.
Technical support via telephone is also available. In the U.S. or Canada, call 1-800-539-6275. For other countries or regions, go to http://support.lexmark.com.
Troubleshooting 242

Upgrading and migrating 243
Hardware
CAUTION—SHOCK HAZARD: To avoid the risk of electrical shock, if you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet, and then from the printer.
3 Using a flat-head screwdriver, open the controller board access cover.

Upgrading and migrating 244

4 Install any supported internal options. For more information, see the documentation that came with the option.
5 Close the access cover.
6 Connect the power cord to the printer, and then to the electrical outlet.
7 Turn on the printer.
CAUTION—SHOCK HAZARD: To avoid the risk of electrical shock, if you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet, and then from the printer.
3 Using a flat‑head screwdriver, open the controller board access cover.

Upgrading and migrating 245
4 Unpack the memory card.
5 Insert the memory card until it clicks into place.

6 Close the access cover.
7 Connect the power cord to the printer, and then to the electrical outlet.
8 Turn on the printer.

Upgrading and migrating 246
CAUTION—SHOCK HAZARD: To avoid the risk of electrical shock, if you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet, and then from the printer.
3 Using a flat‑head screwdriver, open the controller board access cover.
4 Unpack the optional card.
5 Push the card firmly into place.


Upgrading and migrating 247
6 Close the access cover.
7 Connect the power cord to the printer, and then to the electrical outlet.
8 Turn on the printer.
CAUTION—SHOCK HAZARD: To avoid the risk of electrical shock, if you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet, and then from the printer.
3 Using a flat‑head screwdriver, open the controller board access cover.
4 Unpack the hard disk.

Upgrading and migrating 248
5 Attach the hard disk, and then connect the hard disk interface cable to the controller board.

6 Close the access cover.
7 Connect the power cord to the printer, and then to the electrical outlet.
8 Turn on the printer.
CAUTION—SHOCK HAZARD: To avoid the risk of electrical shock, if you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Turn off the printer, and then unplug the power cord from the electrical outlet.
2 Using a flat‑head screwdriver, open the controller board access cover.

Upgrading and migrating 249
3 Unpack the internal solutions port (ISP) kit.


2 Mounting bracket · 3 Thumbscrews

Upgrading and migrating 250
4 If necessary, remove the printer hard disk.
5 Insert the bracket into the board until it clicks into place.

6 Attach the ISP to the bracket.


Upgrading and migrating 251
7 If necessary, attach the hard disk to the ISP. a Remove the hard disk bracket.

b Connect the hard disk to the ISP.

Upgrading and migrating 252

8 Close the access cover.
9 Connect the power cord to the electrical outlet, and then turn on the printer.
CAUTION—SHOCK HAZARD: To avoid the risk of electrical shock, if you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.

Upgrading and migrating 253
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet, and then from the printer.
3 Unpack the optional tray, and then remove all packing material.
4 Align the printer with the optional tray, and then lower the printer until it clicks into place.

5 Connect the power cord to the printer, and then to the electrical outlet.
6 Turn on the printer.
Add the tray in the print driver to make it available for print jobs. For more information, see “Adding available options in the print driver” on page 256.
CAUTION—SHOCK HAZARD: To avoid the risk of electrical shock, if you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet, and then from the printer.

Upgrading and migrating 254
3 Unpack the tray, and then remove all packing material.
4 Install the tray on the caster base.

5 Align the printer with the tray, and then lower the printer until it clicks into place.

Upgrading and migrating 255

6 Connect the power cord to the printer, and then to the electrical outlet.
7 Turn on the printer.
Add the tray in the print driver to make it available for print jobs. For more information, see “Adding available options in the print driver” on page 256.

Upgrading and migrating 256
2 Run the installer, and then follow the instructions on the computer screen.
3 For Macintosh users, add the printer.
1 Open the printers folder.
3 Navigate to the Configuration tab, and then select Update Now ‑ Ask Printer.
4 Apply the changes.
1 From System Preferences in the Apple menu, navigate to your printer, and then select Options & Supplies.
2 Navigate to the list of hardware options, and then add any installed options.
3 Apply the changes.
You can export the configuration settings of your printer into a text file, and then import the file to apply the settings to other printers.
1 Open a web browser, and then type the printer IP address in the address field.
2 Export or import a configuration file for one or multiple applications.

Upgrading and migrating 257
a From the Embedded Web Server, click Apps > the application that you want > Configure. b Click Export or Import.
a From the Embedded Web Server, click Export Configuration or Import Configuration. b Follow the instructions on the screen.
Some applications require a minimum device firmware level to operate correctly.
For more information on updating the device firmware, contact your Lexmark representative.
1 From the Embedded Web Server, click Settings > Device > Update Firmware.
2 Browse to locate the required flash file.
3 Apply the changes.

Product name:
Lexmark MB2770adwhe; Lexmark MX721ade, Lexmark MX721adhe; Lexmark MX722ade, Lexmark MX722adhe; Lexmark MX725adve, Lexmark XM5365, Lexmark XM5370 MFPs
Machine type:
Model(s):
036, 037, 096, 336, 337, 388, 396, 836
The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.
References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.
For Lexmark technical support, go to http://support.lexmark.com.
For information on Lexmark's privacy policy governing the use of this product, go to www.lexmark.com/privacy.
For information on supplies and downloads, go to www.lexmark.com.
© 2018 Lexmark International, Inc.
All rights reserved.
The Software Program and any related documentation are "Commercial Items," as that term is defined in 48 C.F.R. 2.101, "Computer Software" and "Commercial Computer Software Documentation," as such terms are used in 48 C.F.R. 12.212 or 48 C.F.R. 227.7202, as applicable. Consistent with 48 C.F.R. 12.212 or 48 C.F.R. 227.7202-1 through 227.7207-4, as applicable, the Commercial Computer Software and Commercial Software
December 2018

Documentation are licensed to the U.S. Government end users (a) only as Commercial Items and (b) with only those rights as are granted to all other end users pursuant to the terms and conditions herein.
Lexmark and the Lexmark logo are trademarks or registered trademarks of Lexmark International, Inc. in the United States and/or other countries.
Google Cloud Print and Google Chrome are trademarks of Google Inc. Android and Google Play are trademarks of Google LLC.
Macintosh, Mac, App Store, and Safari are trademarks of Apple Inc. AirPrint and the AirPrint logo are trademarks of Apple, Inc.
Microsoft, Windows, and Internet Explorer are either registered trademarks or trademarks of the Microsoft group of companies in the United States and other countries.
Mopria®, the Mopria® logo, and the Mopria® Alliance logo are registered trademarks and service marks of Mopria Alliance, Inc. in the United States and other countries. Unauthorized use is strictly prohibited.
PCL® is a registered trademark of the Hewlett-Packard Company. PCL is Hewlett-Packard Company’s designation of a set of printer commands (language) and functions included in its printer products. This printer is intended to be compatible with the PCL language. This means the printer recognizes PCL commands used in various application programs, and that the printer emulates the functions corresponding to the commands.
PostScript is a registered trademark of Adobe Systems Incorporated in the United States and/or other countries.
All other trademarks are the property of their respective owners.
All licensing notices associated with this product can be viewed from the CD:\NOTICES directory of the installation software CD.
The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.
1-meter average sound pressure, dBA
Printing One-sided: 57 (MB2770, MX721, MX722, XM5365, XM5370); 56 (MX725) Two-sided: 56 (MX721, XM5365); 57 (MB2770, MX722, XM5370); 55 (MX725)
Scanning 56 (MB2770, MX721, MX722, XM5365, XM5370); 57 (MX725)

1-meter average sound pressure, dBA
Copying 60 (MB2770, MX721, MX722, XM5365, XM5370); 59 (MX725)
Ready 14 (MB2770, MX721, MX722, XM5365, XM5370); 28 (MX725)
Values are subject to change. See www.lexmark.com for current values.
The WEEE logo signifies specific recycling programs and procedures for electronic products in countries of the European Union. We encourage the recycling of our products.
If you have further questions about recycling options, visit the Lexmark Web site at www.lexmark.com for your local sales office phone number.
This product complies with the India E-Waste (Management and Handling) Rules, 2011, which prohibit use of lead, mercury, hexavalent chromium, polybrominated biphenyls, or polybrominated diphenyl ethers in concentrations exceeding 0.1% by weight and 0.01% by weight for cadmium, except for the exemption set in Schedule II of the Rules.
Do not dispose of the printer or supplies in the same manner as normal household waste. Consult your local authorities for disposal and recycling options.

This symbol identifies static-sensitive parts. Do not touch the areas near these symbols without first touching a metal surface in an area away from the symbol.
To prevent damage from electrostatic discharge when performing maintenance tasks such as clearing paper jams or replacing supplies, touch any exposed metal frame of the printer before accessing or touching interior areas of the printer even if the symbol is not present.
Any Lexmark product bearing the ENERGY STAR® emblem on the product or on a start-up screen is certified to comply with Environmental Protection Agency (EPA) ENERGY STAR requirements as configured when shipped by Lexmark.
Operating temperature and relative humidity 10 to 32.2°C (50 to 90°F) and 15 to 80% RH 15.3 to 32.2°C (60 to 90°F) and 8 to 15% RH Maximum wet bulb temperature: 22.8°C (73°F) Printer / cartridge / imaging unit long- term storage1
Printer / cartridge / imaging unit short-term shipping
-40 to 43.3°C (-40 to 110°F)
1 Supplies shelf life is approximately 2 years. This is based on storage in a standard office environment at 22°C (72°F) and 45% humidity.
2 Wet-bulb temperature is determined by the air temperature and the relative humidity.
The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR, Chapter I, Subchapter J for Class I (1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements of IEC 60825-1: 2014.
Class I laser products are not considered to be hazardous. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance,

or prescribed service conditions. The printer has a non-serviceable printhead assembly that contains a laser with the following specifications:
The following table documents the power consumption characteristics of the product.
Mode Description Power consumption (Watts)
Printing The product is generating hard‑copy output from electronic inputs.
One-sided: 800 (MX721, XM5365); 850 (MB2770, MX722, XM5370); 750 (MX725) Two-sided: 580 (MX721, XM5365); 640 (MB2770, MX722, XM5370); 570 (MX725)
Copy The product is generating hard‑copy output from hard‑copy original documents.
830 (MX721, XM5365); 890 (MB2770, MX722, XM5370)); 810 (MX725)
Scan The product is scanning hard‑copy documents. 75 (MX721, XM5365); 73 (MB2770, MX722, XM5370);
Ready The product is waiting for a print job. Higher power usage: 41.5 (MX721, XM5365); 42 (MB2770, MX722, XM5370); 118 (MX725) Lower power usage: 31 (MX721, XM5365); 32 (MB2770, MX722, XM5370); 94 (MX725)
Sleep Mode The product is in a high‑level energy‑saving
mode.
Hibernate The product is in a low‑level energy‑saving mode.
Off The product is plugged into an electrical outlet, but the power switch is turned off.
The power consumption levels listed in the previous table represent time-averaged measurements. Instantaneous power draws may be substantially higher than the average.
Values are subject to change. See www.lexmark.com for current values.
This product is designed with an energy-saving mode called Sleep Mode. The Sleep Mode saves energy by lowering power consumption during extended periods of inactivity. The Sleep Mode is automatically engaged after this product is not used for a specified period of time, called the Sleep Mode Timeout.
Factory default Sleep Mode Timeout for this product (in minutes): 15

By using the configuration menus, the Sleep Mode Timeout can be modified between 1 minute and 120 minutes. Setting the Sleep Mode Timeout to a low value reduces energy consumption, but may increase the response time of the product. Setting the Sleep Mode Timeout to a high value maintains a fast response, but uses more energy.
This product is designed with an ultra‑low power operating mode called Hibernate mode. When operating in Hibernate Mode, all other systems and devices are powered down safely.
The Hibernate mode can be entered in any of the following methods:
Factory default Hibernate Timeout for this product in all countries or regions 3 days
The amount of time the printer waits after a job is printed before it enters Hibernate mode can be modified between one hour and one month.
If this product has an off mode which still consumes a small amount of power, then to completely stop product power consumption, disconnect the power supply cord from the electrical outlet.
It is sometimes helpful to calculate the total product energy usage. Since power consumption claims are provided in power units of Watts, the power consumption should be multiplied by the time the product spends in each mode in order to calculate energy usage. The total product energy usage is the sum of each mode's energy usage.
This section contains regulatory information pertaining to products that contain the analog facsimile card:
Lexmark Regulatory Type/Model Number:
Notice to users of the US telephone network: FCC requirements
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the Administrative Council for Terminal Attachments (ACTA). On the back of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to your telephone company.
This equipment uses the RJ-11C Universal Service Order Code (USOC) jack.
A plug and jack used to connect this equipment to the premises’ wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. Use a compliant telephone cord

(RJ-11) that is 26 AWG or larger when connecting this product to the public switched telephone network. See your setup documentation for more information.
The Ringer Equivalence Number (REN) is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact your local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (for example, 03 is a REN of 0.3). For earlier products, the REN is shown separately on the label.
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify the customer as soon as possible. You will also be advised of your right to file a complaint with the FCC.
The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of this equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.
If you experience trouble with this equipment, for repair or warranty information, contact Lexmark International, Inc. at www.lexmark.com or your Lexmark representative. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
This equipment contains no user serviceable parts. For repair and warranty information, contact Lexmark International, Inc. See the previous paragraph for contact information.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission, or corporation commission for information.
If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including fax machines, to send any message unless said message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message, and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges.)
See your user documentation in order to program this information into your fax machine.
This product meets the applicable Industry Canada technical specifications.
The Ringer Equivalence Number (REN) indicates the maximum number of devices allowed to be connected to a telephone interface. The termination of an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices not exceed five. The REN is located on the product label.
This equipment uses CA11A telephone jacks.

Ce produit est conforme aux spécifications techniques d’Industrie Canada.
Le numéro REN (ringer equivalence number : numéro d’équivalence de sonnerie) indique le nombre maximum d'appareils pouvant être connectés à l’interface téléphonique. En bout de ligne, le nombre d’appareils qui peuvent être connectés n’est pas directement limité, mais la somme des REN de ces appareils ne doit pas dépasser cinq. Le numéro REN est indiqué sur l'étiquette produit.
Cet équipement utilise des prises de téléphone CA11A.
The following are special conditions for the Facsimile User Instructions. The grant of a telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom's network services.
This equipment shall not be set up to make automatic calls to the Telecom “111” Emergency Service.
This equipment may not provide for the effective hand-over of a call to another device connected to the same line.
This equipment should not be used under any circumstances that may constitute a nuisance to other Telecom customers.
This equipment is not capable, under all operating conditions, of correct operation at the higher speeds for which it is designed. Telecom will accept no responsibility should difficulties arise in such circumstances.
The decadic (or pulse) dialing on this device is unsuitable for use on the Telecom network in New Zealand.
For correct operation, the total of all the Ringer Equivalence Numbers (RENs) of all parallel devices connected to the same telephone line may not exceed 5. The REN of this device is located on the label.
This device uses an RJ-11C modular connector. Contact your point of purchase if a BT adapter is required. The Lexmark part number is 80D1873.
Some parameters required for compliance with Telecom's telepermit requirements are dependent on the equipment associated with this device. The associated equipment shall be set to operate within the following limits for compliance to Telecom's specifications:
The installed optional modem is in compliance with Japanese Telecommunication Law and has been Certified by JATE, with Certification Number A11-0160001.

Lexmark International, Inc.
A11-0160001JP
Using this product in Switzerland
This product requires a Swiss billing tone filter (Lexmark part number 80D1877) to be installed on any line which receives metering pulses in Switzerland.
Cet appareil nécessite l’utilisation d’un filtre de tonalité de facturation suisse (nº de référence Lexmark : 80D1877) devant être installé sur toute ligne recevant des impulsions de comptage en Suisse.
Für dieses Produkt muss ein schweizerischer Billing Tone Filter zur Zählzeichenübertragung (Lexmark Teilenummer 80D1877) für jede Leitung installiert werden, über die in der Schweiz Zeitsteuertakte übertragen werden.
Questo prodotto richiede un filtro toni Billing svizzero, (codice Lexmark 80D1877) da installare su tutte le linee che ricevono impulsi remoti in Svizzera.
This section contains regulatory information that applies only to wireless models.
If in doubt as to whether your model is a wireless model, go to http://support.lexmark.com.
Wireless‑equipped models contain the following modular component(s):

The radiated output power of this device is far below the radio frequency exposure limits of the FCC and other regulatory agencies. A minimum separation of 20 cm (8 inches) must be maintained between the antenna and any persons for this device to satisfy the RF exposure requirements of the FCC and other regulatory agencies.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that necessary for successful communication.
This device complies with Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
To prevent radio interference to the licensed service and to reduce the potential for harmful interference to co- channel mobile satellite systems, this device is intended to be operated indoors and away from windows to provide maximum shielding.
High-power radars are allocated as primary users (i.e., priority users) of the bands 5250–5350MHz and 5650– 5850MHz. These radars could cause interference and/or damage to LE-LAN devices.
Selon la réglementation d'Industrie Canada, l'émetteur radio ne fonctionne qu'avec une antenne dont le type et le gain maximal (ou inférieur) ont été approuvés par Industrie Canada. Pour réduire les interférences radio potentielles auprès d'autres utilisateurs, le type d'antenne et son gain doivent être choisis de telle sorte que la puissance isotrope rayonnée équivalente (PIRE) ne soit pas supérieure à ce qui est nécessaire pour assurer la réussite de la communication.
Cet appareil est conforme aux normes RSS exemptes de licence d'Industrie Canada. Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interférences et (2) il doit accepter toutes les interférences, y compris les celles qui peuvent entraîner un fonctionnement indésirable.
Afin de prévenir les interférences radio des services sous licence et pour réduire le risque d'interférences nuisibles aux systèmes de satellites mobiles utilisant les mêmes canaux, cet appareil est destiné à être utilisé à l’intérieur et loin des fenêtres afin de fournir une protection maximale.
Les radars à haute puissance sont définis comme les utilisateurs principaux (p. ex., utilisateurs prioritaires) dans les bandes de 5250-5350 MHz et 5650-5850 MHz. Ces radars peuvent causer des interférences ou des dommages aux appareils RELOC-EL.
This product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The FCC Class A limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
The manufacturer is not responsible for any radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment.
Any questions regarding this compliance information statement should be directed to:
Director of Lexmark Technology & Services Lexmark International, Inc. 740 West New Circle Road Lexington, KY 40550 Telephone: (859) 232–3000 E-mail: regulatory@lexmark.com
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Standard ICES-003.
Cet appareil numérique de classe A est conforme aux exigences de la norme canadienne relative aux équipements pouvant causer des interférences NMB-003.

This product is in conformity with the protection requirements of EC Council directive 2014/53/EU on the approximation and harmonization of the laws of the Member States relating to radio equipment.

The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY. A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative or may be obtained at www.lexmark.com/en_us/about/regulatory-compliance/european-union-declaration-of-conformity.html.
Compliance is indicated by the CE marking:
This radio equipment is restricted to indoor use only. Outdoor use is prohibited. This restriction applies to all the countries listed in the table below:

AT BE BG CH CY CZ DE DK EE
EL ES FI FR HR HU IE IS IT
LI LT LU LV MT NL NO PL PT
EU statement of radio transmitter operational frequency bands and maximum RF power
This radio product transmits in either the 2.4GHz (2.412–2.472 GHz in the EU) or 5GHz (5.15–5.35, 5.47–5.725 in the EU) bands. The maximum transmitter EIRP power output, including antenna gain, is ≤ 20dBm for both bands.
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Standard ICES-003.
Cet appareil numérique de classe A est conforme aux exigences de la norme canadienne relative aux équipements pouvant causer des interférences NMB-003.

Este produto não é apropriado para uso em ambientes domésticos, pois poderá causar interferências eletromagnéticas que obrigam o usuário a tomar medidas necessárias para minimizar estas interferências.
This product is in conformity with the protection requirements of EC Council directives 2014/30/EU, 2014/35/EU, and 2011/65/EU on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits, and on the restrictions of use of certain hazardous substances in electrical and electronic equipment.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY. A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative or may be obtained at www.lexmark.com/en_us/about/regulatory-compliance/european-union-declaration-of-conformity.html.
This product satisfies the Class A limits of EN 55022 and EN55032 and safety requirements of EN 60950‑1 or EN 62368-1.
This is a product that complies with the emission requirements of EN55022 and EN55032 Class A limits and immunity requirements of EN55024. This product is not intended to be used in residential/domestic environments.
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
STATEMENT OF LIMITED WARRANTY FOR LEXMARK LASER PRINTERS, LEXMARK LED PRINTERS, AND LEXMARK MULTIFUNCTION LASER
This limited warranty applies to the United States and Canada. For customers outside the U.S., refer to the country-specific warranty information that came with your product.
This limited warranty applies to this product only if it was originally purchased for your use, and not for resale, from Lexmark or a Lexmark Remarketer, referred to in this statement as “Remarketer.”
Lexmark warrants that this product:
—Is manufactured from new parts, or new and serviceable used parts, which perform like new parts

—Is, during normal use, free from defects in material and workmanship
If this product does not function as warranted during the warranty period, contact a Remarketer or Lexmark for repair or replacement (at Lexmark's option).
If this product is a feature or option, this statement applies only when that feature or option is used with the product for which it was intended. To obtain warranty service, you may be required to present the feature or option with the product.
If you transfer this product to another user, warranty service under the terms of this statement is available to that user for the remainder of the warranty period. You should transfer proof of original purchase and this statement to that user.
The warranty period starts on the date of original purchase as shown on the purchase receipt and ends 12 months later provided that the warranty period for any supplies and for any maintenance items included with the printer shall end earlier if it, or its original contents, are substantially used up, depleted, or consumed. Fuser Units, Transfer/Transport Units, Paper Feed items, if any, and any other items for which a Maintenance Kit is available are substantially consumed when the printer displays a “Life Warning” or “Scheduled Maintenance” message for such item.
To obtain warranty service you may be required to present proof of original purchase. You may be required to deliver your product to the Remarketer or Lexmark, or ship it prepaid and suitably packaged to a Lexmark designated location. You are responsible for loss of, or damage to, a product in transit to the Remarketer or the Lexmark designated location.
When warranty service involves the exchange of a product or part, the item replaced becomes the property of the Remarketer or Lexmark. The replacement may be a new or repaired item.
The replacement item assumes the remaining warranty period of the original product.
Replacement is not available to you if the product you present for exchange is defaced, altered, in need of a repair not included in warranty service, damaged beyond repair, or if the product is not free of all legal obligations, restrictions, liens, and encumbrances.
As part of your warranty service and/or replacement, Lexmark may update the firmware in your printer to the latest version. Firmware updates may modify printer settings and cause counterfeit and/or unauthorized products, supplies, parts, materials (such as toners and inks), software, or interfaces to stop working. Authorized use of genuine Lexmark products will not be impacted.
Before you present this product for warranty service, remove all print cartridges, programs, data, and removable storage media (unless directed otherwise by Lexmark).
For further explanation of your warranty alternatives and the nearest Lexmark authorized servicer in your area contact Lexmark on the World Wide Web.
Remote technical support is provided for this product throughout its warranty period. For products no longer covered by a Lexmark warranty, technical support may not be available or only be available for a fee.
Lexmark does not warrant uninterrupted or error-free operation of any product or the durability or longevity of prints produced by any product.
Warranty service does not include repair of failures caused by:
—Modification or unauthorized attachments

—Accidents, misuse, abuse or use inconsistent with Lexmark user’s guides, manuals, instructions or guidance
—Unsuitable physical or operating environment
—Maintenance by anyone other than Lexmark or a Lexmark authorized servicer
—Operation of a product beyond the limit of its duty cycle
—Use of printing media outside of Lexmark specifications
—Refurbishment, repair, refilling or remanufacture by a third party of products, supplies or parts
—Products, supplies, parts, materials (such as toners and inks), software, or interfaces not furnished by Lexmark
TO THE EXTENT PERMITTED BY APPLICABLE LAW, NEITHER LEXMARK NOR ITS THIRD PARTY SUPPLIERS OR REMARKETERS MAKE ANY OTHER WARRANTY OR CONDITION OF ANY KIND, WHETHER EXPRESS OR IMPLIED, WITH RESPECT TO THIS PRODUCT, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND SATISFACTORY QUALITY. ANY WARRANTIES THAT MAY NOT BE DISCLAIMED UNDER APPLICABLE LAW ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. NO WARRANTIES, EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD. ALL INFORMATION, SPECIFICATIONS, PRICES, AND SERVICES ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE.
Your sole remedy under this limited warranty is set forth in this document. For any claim concerning performance or nonperformance of Lexmark or a Remarketer for this product under this limited warranty, you may recover actual damages up to the limit set forth in the following paragraph.
Lexmark's liability for actual damages from any cause whatsoever will be limited to the amount you paid for the product that caused the damages. This limitation of liability will not apply to claims by you for bodily injury or damage to real property or tangible personal property for which Lexmark is legally liable. IN NO EVENT WILL LEXMARK BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, INCIDENTAL DAMAGE, OR OTHER ECONOMIC OR CONSEQUENTIAL DAMAGES. This is true even if you advise Lexmark or a Remarketer of the possibility of such damages. Lexmark is not liable for any claim by you based on a third party claim.
This limitation of remedies also applies to claims against any Suppliers and Remarketers of Lexmark. Lexmark's and its Suppliers' and Remarketers' limitations of remedies are not cumulative. Such Suppliers and Remarketers are intended beneficiaries of this limitation.
Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or limitation of incidental or consequential damages, so the limitations or exclusions contained above may not apply to you.
This limited warranty gives you specific legal rights. You may also have other rights that vary from state to state.






Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.