
User Manual
Machine type(s):
Models:
330, 335, 530


Safety information 6
Conventions
LET OP: Note indicates a potentially dangerous situation that can cause personal injury.
Examples of such warnings are:
PLEASE NOTE: RISK OF INJURY: Danger of injury.
NOTE: DANGER OF ELECTRIC SHOCKS: Risk of electric shock.
NOTE: HOT SURFACE: Risk of burning in contact.
NOTE: TILT RISK: - Smell danger.
PLEASE NOTE: RISK OF INJURY: To avoid the risk of electric shocks or fire, you need to connect the power cord directly to a grounded outlet close to the product and which is easily accessible.
PLEASE NOTE: RISK OF INJURY: You must not use this product with extension cords, plug boxes, distributors or UPS devices. The power capacity of this type of accessories can be easily exceeded by a laser printer, which can lead to poor printer performance, property damage or fire.
PLEASE NOTE: RISK OF INJURY: For this product, only use a Lexmark overvoltage protection that is correctly connected between the printer and the supplied power cord. Using non-Lexmark span protections can lead to poor printer performance, property damage or fire.
NOTE: DANGER OF ELECTRIC SHOCKS: To avoid the risk of electric shocks, do not place or use this product near water or damp locations.
PLEASE NOTE: RISK OF INJURY: This product uses a laser. The use of other modes, methods or procedures than those mentioned in the User's Manual may result in exposure to hazardous radiation.
This product uses a printing process that heats the print material. The heat can cause the printing material to release certain substances. Study the section in the operating instructions that discuss guidelines for selecting printing materials to prevent harmful emissions.
PLEASE NOTE: RISK OF INJURY: The lithium battery in this product should not be replaced. If the lithium battery is not properly replaced, there is an explosion risk. A lithium battery shall not be recharged, disassembled or incinerated. Dispose of used lithium batteries as instructed by the manufacturer and keep in mind local regulations.

Safety information 7
PLEASE NOTE: RISK OF INJURY: Follow these guidelines when moving the printer to prevent injury or damage of your printer:
PLEASE NOTE: RISK OF INJURY: Use only the power cord supplied with this product or a replacement component approved by the manufacturer to prevent fire or electric shocks.
NOTE: HOT SURFACE: The inside of the printer can be hot. To avoid injury, you should cool a hot surface before touching it.
NOTE: DANGER OF ELECTRIC SHOCKS: If you want to access the controller card or install optional hardware or memory devices after setting up the printer, turn off the printer and pull the plug before continuing. If you have other devices connected to the printer, turn it off and unplug the cables from the printer.
NOTE: DANGER OF ELECTRIC SHOCKS: To avoid the risk of electric shocks, make sure that all external connections (such as Ethernet and telephone system connections) are correctly placed in the marked ports.
This product has been developed, tested and approved together with specific components of the manufacturer according to strict safety standards applicable worldwide. The safety features of certain components are not always clearly visible. The manufacturer shall not be responsible for the use of other replacement parts.
PLEASE NOTE: RISK OF INJURY: You should not cut, rotate, tie, pinch or place heavy objects on the cord. Make sure that no abrasions can occur on the power cord or pressure is placed on the cable. Make sure the power cord doesn't get entangled between two objects, like a piece of furniture and a wall. If any of these things happen, there's a chance of fire or electric shocks. Check the power cord regularly for such problems. Pull the power cord plug out of the socket before checking the power cable.
Have maintenance and repair operations not described in the user documentation carried out by a service representative.
NOTE: DANGER OF ELECTRIC SHOCKS: To avoid the risk of electric shocks, pull the power cord plug out and unplug all cables connected to the printer before cleaning the outside of the printer.

Safety information 8
PLEASE NOTE: RISK OF INJURY: Make sure to place paper separately in each tray to prevent equipment instability. Keep all other drawers closed until you need them.
NOTE: DANGER OF ELECTRIC SHOCKS: During thunderstorm, you should not install this product and do not build electrical connections for example for the fax function or connect cables and wires such as a power cord or telephone cable.
KEEP THESE INSTRUCTIONS.

Dealing with the printer 9
Use of this manual
This User's Guide contains general and specific information about the use of the printer models listed on the front page.
The following chapters contain information applicable to all printer models:
Find instructions for your printer:

Dealing with the printer 10

Dealing with the printer 11
When placing the printer, take into account space for opening drawers, valves and doors. If you plan to install optional hardware parts, you should also keep enough space for this. The following is important:
Ambient temperature 16 to 32 °C
Temperature for storage -20 to 40 °C

PLEASE NOTE: RISK OF INJURY: Make sure to place paper separately in each tray to prevent equipment instability. Keep all other drawers closed until you need them.

Dealing with the printer 12
You can customize the printer by adding an optional tray for 250 or 550 sheets. See "Install optional loading" on page 17 for instructions to install the optional drawer.


1 Control Panel · 9 Front valve

Dealing with the printer 13

4 Unlock button on front valve
5 Access valve of the controller card
6 Standard drawer for 250 sheets
7 Optional tray for 250 or 550 sheets
8 Universe charger for 50 sheets

Setup additional printer 14
Install Internal Options
NOTE: DANGER OF ELECTRIC SHOCKS: If you want to access the controller card or install optional hardware or memory devices after setting up the printer, turn off the printer and pull the plug before continuing. If you have connected other devices to the printer, disable them and unplug the cables from the printer.
NOTE: DANGER OF ELECTRIC SHOCKS: If you want to access the controller card or install optional hardware or memory devices after setting up the printer, turn off the printer and pull the plug before continuing. If you have other devices connected to the printer, turn it off and unplug the cables from the printer.
1 Open the access valve of the controller card.

2 Check where the memory card connection is located.

Configure Extra Printer 15


NOTE: DANGER OF ELECTRIC SHOCKS: If you want to access the controller card or install optional hardware or memory devices after setting up the printer, turn off the printer and pull the plug before continuing. If you have connected other devices to the printer, disable them and unplug the cables from the printer.
1 Open the controller card access panel.
See 'Get Access to the Controller Card' on page 14 for more information.
2 Remove the optional card from the package.

Configure Extra Printer 16
3 Hold the card at the sides and place pins (1) on the bottom of the chart at an equal height with the recesses (2) in the controller card.


4 Press the card firmly in place as shown on the image.


Configure Extra Printer 17
5 Close the access valve to the controller card.
NOTE: DANGER OF ELECTRIC SHOCKS: If you want to access the controller card or install optional hardware or memory devices after setting up the printer, turn off the printer and pull the plug before continuing. If you have connected other devices to the printer, disable them and unplug the cables from the printer.
1 Turn off the printer with the switch on/off and pull the plug out of the socket.


2 Unpack the drawer and remove the packaging material.
3 Remove the drawer from base unit.


Configure Extra Printer 18
4 Take the packaging material out of the drawer.
5 Move the drawer into base unit.
6 Place the drawer near the printer.
7 Line the printer with the drawer and slowly lower the printer in place.

8 Connect the power cord to the printer, plug it into a grounded outlet and switch on the current.
Connect the printer to your computer with a parallel or USB cable or on the network using an Ethernet cable.
Make sure the following items match:

Configure Extra Printer 19

1 USB port Connecting an optional wireless network adapter.
2 USB printer port Connect the printer to a computer.
3 Ethernet port Connect the printer to a network.
4 Parallel port Connect the printer to a computer.
5 On-off switch Turn on or off the printer.
6 Connection of the printer's power cable
Connect the printer to an outlet.
7 Secure lock Attach a lock that holds the printer in place.
2 Run the installer and follow the instructions on the computer's screen.
3 For Macintosh users: add the printer.
Function component

Configure Extra Printer 20
1 Open the printer folder.
3 Navigate to the Configuration tab and then select Update now - Printer questions.
4 Apply the changes.
1 Navigate via System Preferences in the Apple menu to your printer and then select Options and supplies.
2 Navigate to the list of hardware options and then add any installed options.
3 Apply the changes.
If you want to configure the printer for an Ethernet network, you need to collect the following data before starting:
You need an Ethernet cable to connect the printer to the network and a available network port that will physically connect the printr to the system. Use a new network cable to prevent problems with damaged cables.

Setup additional printer 21
Make sure you have the following data at hand before configuring your printer for a wireless network:
Some ad hoc networks also require the Auto setting. If you are not sure about the channel to select, consult your system administrator. • Security method: there are four options for the security method: – WEP Key
If your network uses multiple WEP keys, you can specify up to four keys in the appropriate locations. Select the key currently used on the network by selecting the default WEP transmission key. – Pre-shared key/password for WPA/WPA2
WPA contains encryption as an additional security level. You can choose from AES or TKIP. Encryption must be set on the router and printer for the same type otherwise the printer cannot communicate on the network. – 802.1X3ADDITIVES
If you install the printer on an 802.1X network, you may need the following data:
If your wireless network does not use security, you will have no security information.
– If you do not know the SSID of the network to which the computer is connected, start the utility
for the wireless network adapter of the computer and search for its network name. Please refer to the documentation at the access point or contact your system administrator if you cannot find SSID or security information from your network. – Please refer to the documentation or Embedded Web Server of the access point or contact us
with the system administrator to find out the pre-shared key or password for WPA/WPA2 for the wireless network.

Configure Extra Printer 22
Check the following before you start:
> Institutions > > Network/Ports > > Active NIC > > Auto >
1 Browse the control panel to:
> Institution > > Network/ports > > Network [x] > > Configure Network [x] > >
Wireless > > Set Wireless Connection >
2 Select a wireless connection setting method.
Find Networks Show available wireless connections.
Enter a network name Manually enter the SSID.
Wi-Fi Protected Setup Printer Connect to a wireless network via Wi-FI Protected Set up (WPS).
3 Follow the instructions on the display.
Check the following before connecting your printer to a wireless network:
Use button configuration method
1 Browse the printer's control panel to:
> Network/Ports > > Network [x] > > Network Settings [x] > > Wireless > >
Wi‑Fi Protected Setup > > Start a push-button method >
2 Follow the instructions on the display.
Option To

Configure Extra Printer 23
Use PIN configuration method
1 Browse the printer's control panel to:
> Network/Ports > > Network [x] > > Configure Network [x] > > Wireless > >
Wi‑Fi Protected Setup > > Start PIN method >
2 Copy the eight-digit WPS PIN.
3 Open a web browser and enter the IP address of the access point in the address bar.
4 Open the WPS settings. Please refer to the documentation at your access point for more information.
5 Enter the eight-digit PIN and save the setting.
Check the following before connecting the printer to a wireless network:
Use button configuration method
1 Browse the control panel to:
> Institutions > > Networks/ports > > Network [x] > > Configure Network [x] >
> Wireless > > Set Wireless Connection > > Wi‑Fi Protected Setup > >
Start a push-button method >
2 Follow the instructions on the display.
Use PIN configuration method
1 Browse the control panel to:
> Institutions > > Networks/ports > > Network [x] > > Configure Network [x] >
> Wireless > > Set Wireless Connection > > Wi‑Fi Protected Setup > >
Start PIN method >
2 Copy the eight-digit WPS PIN.
3 Open a web browser and type the IP address of the access point in the address bar.

Setup additional printer 24
4 Open the WPS settings. For more information, please refer to the documentation provided at the access point.
5 Enter the eight-digit PIN and save the setting.
1 Check that the printer software is already installed.
2 Use the Search command in the Start menu to find the printer home page.
3 Open the printer home page and then click Institutions > Wireless Setup Utility.
4 Follow the instructions on the computer screen.
With the Wireless Configuration Assistant you can do the following:
Install wireless configuration assistant
1 Go to the Lexmark website for support on http://support.lexmark.com.
2 Download the latest Wi-Fi Configuration Assistant.
3 Double-click on the downloaded installation package.
4 Follow the instructions on the screen.
Open wireless configuration assistant

Configure Extra Printer 25
1 Browse the Finder to:
Programmes > select the printer folder
2 Double-click on Wireless Configuration Assistant and follow the instructions on the screen.
? if problems occur during the execution of the application.
Check the following before you start:
1 Open a web browser and type the printer IP address in the address bar.
2 Click on Institutions > Network/Ports > Wireless.
3 Adjust the settings to match the setting of the access point (wireless router).
4 Click on Send.
5 Turn off the printer and then unplug Ethernet cable. Then wait at least five seconds before you turn the printer back on.
6 You can check if the printer is connected to a network by printing a page with network settings. Then check the Network Map [x] section to see if the status is connected.
Print a page with menu settings to view the current menu configuration and check that printer options are installed correctly.

Configure additional printer 26
Note: If you have not made any changes to the settings of the menu items, all default settings will be displayed on the Menu Settings page. When you have selected and saved other settings in the menus, default settings are replaced by user's default setting. A default setting chosen by the user will remain in force until you re-open, select another value and save it.
Browse the printer's control panel to:
> Reports > > Page Menu Settings >
If the printer is connected to a network, you can check the network connection by printing a network configuration page. This page also contains information that is important in the configuration of printing over a network.
1 Browse the printer's control panel to:
> Reports > > Network Configuration Page >
2 Check the first part of the network configuration page to check if Status indicates that the printer is connected.
If Status indicates that the printer is not connected, it may be that the LAN connection point is not active or that the network cable is not functioning properly. Ask the system administrator for a solution to this problem and then print another page with network settings.
Print a page with menu settings to view the current menu configuration and check that printer options are installed correctly.
Browse the printer's control panel to:
> Institutions > Reports > > Page with menu settings >

Configure Extra Printer 27
If the printer is connected to a network, you can check your network connection by printing a network configuration page. This page also contains information that is important in the configuration of printing over a network.
1 Browse the printer's control panel to:
> Institutions > Reports > > Network Configuration Page >
2 Check the first part of the page with network settings to see if Status indicates that the printer is connected.
If Status indicates that the printer not connected, it is possible that the LAN connection point is not active or that the network cable is not functioning properly. Ask the system administrator for a solution to this problem and then print another page with network settings.

Use MS312 and MS317 28
Use the printer's control panel

4 5 6 7 8
1 Menus, button Opens the menus.
2 Print screen options and display status and error messages.
3 Enable sleep button Sleep mode or slumber mode.
Function component

Use MS312 and MS317 29
8 Button Back Return to the previous screen.
9 Determining the status of the printer.
The colors of the sleep button and indicator lights on the control panel indicate a certain printer status or state.
The printer is disabled or the printer's slumber mode is active.
Blinking green The printer is warming up, processing data or printing.
Brandt green The printer is on, but not active.
Blinking red The printer requires intervention by the user.
Sleep Button, Printer Status Light
The printer is disabled, not active or ready to go.
Brandt orange The printer is in sleep mode.
Flick orange The slumber mode of the printer is switched on or off.
Flashes orange according to a slow pattern where the button burns for 0.1 seconds and goes out 1.9 seconds.
The printer's slumber mode is active.
1 Go http://support.lexmark.com and download the software.
2 Double-click on the installation package.
3 Select an installation type and click Install.
4 Click on Install to start the installation.
5 Click on Agreed to agree with the license agreement.
6 Click on Continue and follow the directions on your computer.
Function component · Printer status indicator lamp

Use MS312 and MS317 30
1 Open the local printer settings utility in the application list or Start menu to adjust the printer setting.
2 Save changes via the Actions menu.

Use MS315, MS415 and MS417 31
Use the control panel

1 Display Printer status and messages. Configure and operate the printer.
9 Button Back (Back) This lets you go back to the previous screen.
The colors of the sleep button and indicator lights indicate a certain printer status or state.

Use MS315, MS415 and MS417 32
The printer is disabled or the printer's slumber mode is active.
Blinking green The printer is warming up, processing data or printing.
Brandt green The printer is on, but not active.
Blinking red The printer requires intervention by the user.
Sleep button light Printer status
The printer is disabled, not active or ready to go.
Brandt orange The printer is in sleep mode.
Flick orange The slumber mode of the printer is switched on or off.
Flashes orange according to a slow pattern where the button burns for 0.1 seconds and goes out 1.9 seconds.
The printer's slumber mode is active.
The Embedded Web Server is the printer's web page that allows you to view and configure remote printer settings when you are not near the printer.
2 Open a web browser and type the printer IP address in the address bar.
3 Press Enter.
Indication lamp Printer status

Place paper and special printing material 33
MS312 and MS317: Set paper size and type
1 Browse the printer's control panel to:
> Paper Menu > > Paper Size/Species >
2 Select Tray [x] Format or Tray [x] Species and press on.
3 Change the paper size or type and press .
The universal paper format is a user-defined setting that allows you to print on paper formats that are not preset in the printer menus.
Browse the control panel to:
> Paper Menu > > Universal Settings > > Units of measurement > > select the unit of measurement
1 Browse the control panel to:
> Paper Menu > > Universal Settings > > Units of measurement > > select the
2 Press the arrow keys until Height Standing or Width Standing is displayed and press .
> · unit of measurement >

Paper and special printing material 34
3 Change the settings and press .
1 Browse the printer's control panel to:
> Institutions > > Paper Menu > > Paper Size/Species >
2 Browse with the arrow up or down to the paper drawer or input tray and press .
3 Browse with the arrow up or down to paper size and press .
4 Browse with the arrow up or down to the type of paper and press to change the settings.
The universal paper format is a user-defined setting that allows you to print on paper formats that are not preset in the printer menus.
1 Browse the control panel to:
> Institutions > > Paper Menu > > Universal Settings > > Units of measurement >
> and select a unit of measure. >
2 Select Standing width or Standing height and press on.
3 Press the arrow to the left or right to change the setting and press .
The standard drawer can contain up to 150 sheets of 75 g/m2 paper. Prints are delivered with the print side down. The standard drawer contains a paper stopper that prevents paper from slipping out of the front of the drawer when stacked.

Place paper and special printing material 35
If you want to open the paperstop, pull on the papertop so that it folds forward.

PLEASE NOTE: RISK OF INJURY: Make sure to place paper separately in each tray to prevent equipment instability. Keep all other drawers closed until you need them.
1 Pull the drawer out completely.


Paper and special printing material 36
2 Press the width guide and slide it to the right position for the size of paper you place in the drawer


LGL
B5
EXEC
A5
3 Press the length guide and move it to the right position for the size of paper you place in the drawer.


LGL
B5
EXEC
A5

Paper and special printing material 37



LTR/LGL EXEC
A5
4 Bend the sheets a few times and fan them out. Do not fold or wrinkle the paper. Straighten the pile on a flat surface.


Paper and special printing material 38
5 Place the paper pile in the printer.


Paper and special printing material


6 Place the drawer.

7 Specify the type and size of paper in the tray from the Paper menu on the printer control panel.

Paper and special printing material 40
Use the universal charger when printing on different paper sizes and types or special printing materials, such as cardboard, transparencies, paper labels and envelopes. You can also use the universal charger for single-sided printing tasks on letterhead paper.
1 Open the universal charger.


a Remove the extension of the universal charger.

b Gently pull the extension until the universal loader is fully pulled out and opened.


Paper and special printing material
2 Press the tab on the left width guide and move the conductors to the right position for the size paper you place in the drawer


3 Prepare the paper or special printing material to place it. • Bend the sheets a few times to untie them and then fan them out. Do not fold or wrinkle the paper. Straighten the pile on a flat surface.

4 Place the paper or special material.

Paper and special printing material 42




Paper and special printing material places 43


5 In the Paper menu on the printer control panel, specify the paper size and type corresponding to the paper or special printing material in the universal loader.

Place paper and special printing material 44
The printer connects loading when the specified paper size and the given type of paper are the same. If one of the connected drawers becomes empty, then the next linked drawer will be automatically used. If you do not want loading to be linked, give the type of paper a unique name.
Use Embedded Web Server
1 Open a web browser and type the printer IP address in the address bar.
2 Click on Institutions > Paper Menu.
4 Click on Send.
Use printer settings on the computer
Depending on your operating system, you can open the Paper menu via the Local Printer Settings Tool or through Printer Sets.
Use Embedded Web Server
1 Open a web browser and type the printer IP address in the address bar.

Place paper and special printing material 45
2 Click on Institutions > Paper Menu > Custom species.
3 Select a custom paper type name and then select a custom document type.
4 Click on Send.
Use printer settings on the computer
Depending on your operating system, you can access the Custom menu via the Local Printer Settings Tool or through Printer Sets.
Use Embedded Web Server
1 Open a web browser and type the printer IP address in the address bar.
2 Click on Institutions > Paper Menu.
3 Select a paper source in the Loading Configuration section and then select an adapted type of paper from the Paper Type column.
4 Click on Send.
Use printer settings on the computer
Depending on your operating system, you can open the Paper menu via the Local Printer Settings Tool or through Printer Sets.
1 Open a web browser and type the printer IP address in the address bar.

Paper and special printing material 46
2 Click on Institutions > Paper Menu.
4 Click on Send.
Use Embedded Web Server
1 Open a web browser and type the printer IP address in the address bar.
2 Click on Institutions > Paper Menu > Custom Names.
3 Select a custom name and then type a new modified paper type name.
4 Click on Send.
5 Click on Custom species and check that the new modified paper type name has replaced the custom name.
Use the printer's control panel
1 Browse the printer's control panel to:
> Institutions > > Paper Menu > > Custom Names
2 Select a custom name and then type a new modified paper type name.

Paper and special printing material
3 Press it.
4 Press Custom species and check that the new modified paper type name has replaced the custom name.
Use Embedded Web Server
1 Open a web browser and type the printer IP address in the address bar.
2 Click on Institutions > Paper Menu > Custom species.
3 Select a custom paper type name and then select a paper type.
4 Click on Send.
Use the printer's control panel
1 Browse the printer's control panel to:
> Institutions > > Paper Menu > > Custom species
2 Select a custom paper type name and then select a paper type.
3 Press it.

Manual for paper and special printing material 48
Guidelines for paper
The following paper properties affect the printing quality and reliability of the printer. Please take these characteristics into account when considering a new type of paper.
The printer drawers can automatically enter paper weighing up to 90 g/m2 with the length-long fiber. The universal charger can automatically enter paper weighing up to 163 g/m2 with the length-long fiber. Paper lighter than 60 g/m2 may not be sturdy enough to enter correctly, allowing paper failures. The best result is with 75 g/m2 paper and the length-long fiber. For paper smaller than 182 x 257 mm (7.2 x 10.1 inches) it is best to use 90 g/m2 or more.
Curlying is the tendency of paper to bend at the edges. This can cause input problems. Paper can curl up after it has been passed through the printer and is exposed to high temperatures. If you keep paper outside the packaging or in its drawers under hot, damp, cold or dry conditions, it may curl over before printing. This can cause input problems.
The smoothness of paper directly affects the printing quality. If paper is too rough, toner is not fixed properly. Too smooth paper can cause input problems or print quality issues. Use paper with a smoothness between 100 and 300 Sheffield points. However, a smoothness between 150 and 250 Sheffield points gives the best print quality.
The amount of moisture in paper affects the printing quality and also determines whether it can be passed through the printer. Leave the paper in the original package until you start using it. The paper is not then exposed to the negative influence of changes in humidity.
Allow the paper to acclimatize in its original packaging and environments for 24-48 hours before printing. Extend this period by a few days if the storage or transport environment differs considerably from the printer environment. Thick paper may need a longer acclimatisation period.
The direction of fibre refers to the alignment of paper fibres into a sheet of paper. Fibres are either longitudinally oriented or in the direction of latitude.

Manual for paper and special printing material 49
For a weight of 60-90 g/m2, it is best to use paper with the length-long fiber.
High quality xerographic paper is usually 100% chemically treated wood pulp. This wood pulp content provides a high degree of stability to the paper, reducing import problems and improving print quality. If paper contains other fibres, for example cotton, this may lead to problems in processing.
The use of the following paper types in the printer is not recommended:
Using the right paper prevents malfunctions and ensures that you can print without any problems.
You can prevent paper failures and poor printing quality as follows:
Please follow the following guidelines when choosing preprinted forms and letterhead paper:

Manual for paper and special printing material 50
Use paper printed with heat resistant ink that is suitable for copiers. The ink must be resistant to temperatures of 230 C without melting or releasing harmful substances. Do not use ink that is affected by the resin in the toner. Water or oil-based ink should meet these requirements. However, Latex ink could cause problems. If in doubt, please contact your paper supplier.
Preprinted paper, such as letterhead paper, must be resistant to temperatures up to 225 °C without melting or releasing dangerous substances.
Lexmark is an environmentally conscious company and therefore encourages the use of recycled paper that has been specially produced for use in laser printers (electrophotographic).
Although it cannot be stated by definition that all types of recycled paper can be correctly imported, Lexmark continuously tests paper varieties falling into the category of custom cut recycling paper for copiers available worldwide. These expert tests are performed extremely accurately and methodically. Many factors are considered, both in themselves and in combination, including the following:
Wrapping paper has a better quality than ever. However, the amount of recycled material in paper affects the management of unwanted effects. And although the use of recycled paper is a good way to print in an environmentally conscious manner, this method is not perfect. The energy needed to remove ink and process additives such as colours and 'glue' often produces higher carbon emissions than the production of normal paper. However, overall the use of recycled paper improves resource management.
Lexmark is involved in responsible paper use generally, based on the assessment of life cycles of its products. To gain a better understanding of the environmental impact of printers, the company carried out a number of life cycle assessments and concluded that paper makes the largest contribution (maximum 80%) to carbon emissions during the lifetime of an appliance (from design up to end-of-life). The reason for this is that paper production processes consume a lot of energy.
That's why Lexmark is looking for ways to inform customers and partners about minimising the influence of paper. The use of recycled paper is one way. Avoiding excessive and unnecessary paper consumption is another way. Lexmark has the right resources to help customers minimise their required amount of print and copy material. In addition, the company encourages customers to buy paper from suppliers who want to contribute to sustainable forestry.

Manual for paper and special printing material 51
Lexmark does not make recommendations about certain suppliers, but maintains a list of similar products for special applications. If you use the following paper choice guidelines, limit the impact of printing on the environment:
1 Minimize paper consumption.
2 Be critical of the origin of wood fibre. Buy paper from suppliers who have certifications as FSC (Forestry Stewardship Council) or PEFC (Program for the Endorsement of Forest Certification). These certifications ensure that the paper supplier uses wood pulp from forest owners who apply sustainable and socially responsible forest management and reforestation.
3 Choose the right paper for your printing needs: normally certified 75 or 80 g/m2 paper with a lower paper weight or recycled paper.
Research results indicate that the following paper types are not suitable for use in a laser printer:
Go to the Lexmark website on www.lexmark.com for more information. General information on sustainability can be found via the link Sustainability.
Keep the following paper storage guidelines to ensure regular printing quality and prevent any paper failures.

Manual for paper and special printing material 52
Cardboard is a heavy, single layer special printing material. Many variable characteristics, such as moisture content, thickness and structure, can significantly influence the print quality. Before purchasing large quantities of cardboard, make some test prints.
When printing cardboard, note the following:
First, make some proofs before purchasing large quantities of envelopes.
– easy curling; – sticking together or damaged; – contain windows, holes, perforations, cut-outs or relief; – containing metal clips, bows or folding clamps; – are folded together; – containing stamps; – have a (partially) uncovered adhesive strip when the valve side is closed or pasted; – have curved angles; – have a rough, folded or laminated finish. • Adjust the width guides so that they match the width of the envelopes.

Manual for paper and special printing material 53
Before purchasing large quantities of labels, make some proofs.
Please refer to the Card Stock & Label Guide on http://support.lexmark.com for more information on printing, labelling characteristics and design.
When printing labels, note the following:
– Labels cannot be attached to a 240°C exposure and stick, curling
do not wrinkle or give off hazardous substances at these temperatures. – Label adhesive, front (printed material) and coating are resistant to 172 kPa (25 psi) pressure
– 'Fill Loads' on page 35 – 'Fill the universal charger' on page 40

Manual for paper and special printing material 54
For information about cardboard and labels, please refer to the Card Stock & Label Guide on http://support.lexmark.com.
Paper Size Standard Drawer Optional tray for 250 or 550 sheets
Univer & seellader Mode for double-sided printing
A4 210 x 297 mm (8,3 x 11,7 inch)
148 x 210 mm (5.8 x 8.3 inches)
105 x 148 mm (4.1 x 5.8 inches)
182 x 257 mm (7,2 x 10.1 inch)
216 x 279 mm (8,5 x 11 inches)
216 x 356 mm (8,5 x 14 inches)
Executive 184 x 267 mm (7,3 x 10,5 inch)
1 With this format setting, the page is arranged according to dimensions 216 x 356 mm (8.5 x 14 inches), unless another size is specified in the application.
2 Universal is only supported in the standard tray if the paper size has at least 105 x 148 mm (4,1 x 5.8 inches). Universal is only supported in the optional tray for 250 or 550 sheets if the paper size has at least 148 x 210 mm (5,8 x 8.3 inches). Universal is only supported in double-sided printing mode if the paper has a width of 210 mm (8.3 inches) and a length of 279 mm (11 inches). The smallest supported format for Universal can only be placed in the universal charger.
Letter · Legal

Manual for paper and special printing material 55
Paper Size Standard Drawer Optional tray for 250 or 550 sheets
Univer & Seellader Mode for double-sided printing
Oficio (Mexico) 216 x 340 mm (8,5 x 13.4 inch)
216 x 330 mm (8,5 x 13 inches)
Statement 140 x 216 mm (5,5 x 8.5 inches)
From 76.2 x 127 mm (3 x 5 inches) to 216 x 356 mm (8.5 x 14 inches).
7 3/4 envelope (Monarch) 98 x 191 mm (3.9 x 7.5 inches) X X X
Envelope No. 9 98 x 225 mm (3.9 x 8.9 inches)
Envelope No. 10
105 x 241 mm (4.7 x 9.5 inches)
Envelope DL 110 x 220 mm (4.3 x 8.7 inches)
162 x 229 mm (6.4 x 9 inches)
Envelope B5 176 x 250 mm (6.9 x 9.8 inches)
229 x 356 mm (9 x 14 inches)
1 With this format setting, the page is arranged according to dimensions 216 x 356 mm (8.5 x 14 inches), unless another size is specified in the application.
2 Universal is only supported in the standard tray if the paper size has at least 105 x 148 mm (4,1 x 5.8 inches). Universal is only supported in the optional tray for 250 or 550 sheets if the paper size has at least 148 x 210 mm (5,8 x 8.3 inches). Universal is only supported in double-sided printing mode if the paper has a width of 210 mm (8.3 inches) and a length of 279 mm (11 inches). The smallest supported format for Universal can only be placed in the universal charger.
The standard drawer supports paper weights of 60.09.90 g/m2. The optional tray supports paper weights of 60. The universal loader supports paper weights of 60 .a.163 g/m2.

Manual for paper and special printing material 56

1 The printer supports occasional use of single sided paper labels designed for laser printers. You should print no more than 20 pages with paper labels per month. Vinyl labels, pharmacies' labels and double-sided labels are not supported.
2 Bank note and heavy paper are supported in double-sided mode up to a paper weight of 90 g/m2.

Print a document
1 Open the Print dialog from the document you want to print.
2 Adjust the settings if necessary.
3 Send the print job.
Use Embedded Web Server
1 Open a web browser and type the printer IP address in the address bar.
2 Click on Institutions > Print Settings > Quality Menu > Toner intensity.
3 Adjust the setting for toner intensity.
4 Click on Send.
Use printer settings on the computer
Depending on your operating system, you can adjust toner intensity settings via the Local Printer Settings Tool or through Printer Sets.
Use the printer's control panel
1 Browse the printer's control panel to:
> Institutions > > Print Settings > > Quality Menu > > Toner intensity >
2 Adjust the toner intensity.
3 Press it.
Print 57

Use Embedded Web Server
1 Open a web browser and type the printer IP address in the address bar.
2 Click on Institutions > Print Settings > Quality Menu > Toner intensity.
3 Adjust toner intensity and click Submit.
Use the printer's control panel
1 Browse the printer's control panel to:
> Institutions > > Print Settings > > Quality Menu > > Toner intensity
2 Adjust toner intensity and press .
Mopria® Print Service is a mobile printing solution, designed for mobile devices with Android 4.4 or later. You can directly print on any printer that is compatible with Mopra.
1 Launch a compatible application from the home screen of your mobile device.
2 Tap Print and select the printer.
3 Send the print job.
Print 58

Google Cloud PrintTM is a mobile printing solution that allows you to print on printers compatible with Googo Cloud printer using enabled applications on mobile devices.
1 Launch a enabled application from the home screen of your mobile device.
2 Tap Print and select the printer.
3 Send the print job.
AirPrint is a mobile printing solution that allows you to print directly from Apple devices on printers compatible with AirPrint.
1 Launch a compatible application from the home screen of your mobile device.
2 Select an item to print and then tap the Share icon.
3 Tap Print and select a printer.
4 Print the document.
LexmarkTM Mobile Print allows you to send documents and images directly to a supported Lex mark printer.
1 Open the document and send or share it to Lexmark Mobile Print.
2 Select a printer.
3 Print the document.
1 Browse the printer's control panel to:
> Security > Secure Printing
2 Select a type of job.
Print 59

Time-protected task Hold print jobs on the computer until you enter the PIN through the printer's control panel.
Max. invalid PIN Limit the number of times that an invalid Pin code can be entered.
Reset time repeated task Print and save print jobs in printer memory.
Save lost job Print jobs so you can print them at a later time.
Checking for decay task Print one copy of a job and hold the remaining copies. This allows you to check that the quality of the first copy is as desired.
3 Press it.
For more information about printing a page with menu settings or network installation page, see:
Browse the printer's control panel to one of the following settings:
> Reports > > Print fonts > > PCL fonts >
Print 60 · Option To · or

> Reports > > Print fonts > > PostScript Fonts >
1 Browse the printer's control panel to:
> Institutions > > Reports > > Print fonts
2 Press the arrow up or down to select a setting.
3 Press it.
Browse the control panel to:
> Institutions > Reports > > Print Directory >
> on the control panel.
2 Select the job you want to cancel.
Print 61 · Press

Saving money and helping the environment 62
Lexmark strives for sustainability and is constantly developing printers in such a way that the environmental burden of the printers is reduced. We design with the environment in mind and we devise packaging that requires as little raw materials as possible, and we offer collection and recycling programmes. For more information, see:
You can probably further limit the environmental burden of your printer when choosing your printer's settings and tasks. This chapter summarises the institutions and tasks that can bring a greater environmental benefit.
Research has shown that up to eighty percent of the ecological footprint of a printer is related to paper consumption. You can significantly reduce your ecological footprint by using recycled paper and following print suggestions, such as double-sided printing and multi-page printing on a single sheet of paper.
See "Use Eco mode" on page 67 for MS312 or "Use ecomodus" on pages 70 for MS315 and MS415 to learn how you can quickly save paper and energy by using one printer setting.
Lexmark is an environmentally conscious company and encourages the use of business recycled paper that has been specially produced for laser printers. See "Use paper on the circular wallet and other office papers" page 50 for more information about recycled paper that you can use in your printer.
Lexmark provides collection programme service and progressive, sustainable recycling approaches. For more information, see:

Saving money and helping the environment 63
You return Lexmark products for reuse as follows:
1 Go www.lexmark.com/recycle.
2 Select the product you want to recycle.
Lexmark is constantly aiming at minimising the packaging material. Using less packaging material guarantees that Lexmark printers are transported as efficiently and environmentally friendly as possible, and fewer packing materials need to be discarded. These efficiencys lead to fewer greenhouse gases and the saving of energy and natural resources.
Lexmark boxes are 100% recyclable in places where corrugated board recycling facilities are available. Such facilities may not be present in your area.
The foam used in Lexmark packaging material is recyclable at places where foam recycling facilities are present. Such facilities may not be present in your area.
If you send a cartridge back to Lexmark, use the carton in which the cartridge is delivered. Lexmark will recycle the box.
With the Lexmark Cartridge Collection Program, you can return used cartridges to Lex Mark for free for reuse or recycling. One hundred percent of empty cartridges returned to Lexmark are reused or processed for recycling. The boxes used to return the cartridges are also recycled.
Lexmark cartridges can be returned for reuse or recycling as follows:
1 Go www.lexmark.com/recycle.
2 Select the product you want to recycle.

Display advanced network information and admin information
This chapter describes general support management tasks carried out with the Embedded Web Server. For information on advanced system support tasks in Lexmark's Support Website, please see the Network Manual on CD Software and Documentation or Admin Guide for Embedded Web Server. http://support.lexmark.com.
1 Open a web browser and type the printer IP address in the address bar.
2 Click on Copy Printer Settings.
3 To change the language, select the desired language in the drop-down list and click Click here to set the language.
4 Click on Printer Settings (Printer settings).
5 Type the IP address of the source and target printer in the fields specified for this purpose.
6 Click on Copy Printer Settings.
You can specify how to receive notifications when supplies are almost empty, empty or very empty, or when the end of supply life is reached. To do this, set the selectable notifications.
Manage Printer 64

1 Open a web browser and type the printer IP address in the address bar.
2 Click on Institutions > Print Settings > Supplies notifications.
3 In the dropdown menu for each supply, select one of the following notification options:
The normal printer behaviour for all supplies takes place.
Only SNMP The printer generates a Simple Network Management Protocol (SNMP) when the supply status is reached. The status of the supply is displayed on the menu page and status page.
Email only The printer generates an email when the supply status is reached. The status of the supply is displayed on the menu page and status page.
Stop possible resumption1 When supply status is reached, the printer stops processing tasks and the user can press a button to continue printing.
Stop without a possible resumption1,2
The printer stops when the supply status is reached. The supply must be replaced before the user can continue printing.
1 The printer generates an email about the supply status when notifications of supplies are enabled.
2 When some supplies are empty, the printer stops to prevent damage.
4 Click on Send.
With the printer's external control panel displayed on your computer screen, you can operate the printer control panel even if you are not near the network printer. You can view the printer status from your screen and perform other printer related tasks.
1 Open a web browser and type the printer IP address in the address bar.
Manage printer 65 · Messages Description

2 Press Enter to open the web page of your printer.
3 Click on External Control Panel > Enable external control panel.
You can view a number of reports from the Embedded Web Server. These reports are useful for determining the status of the printer, network and supplies.
1 Open a web browser and type the printer IP address in the address bar.
2 Click on Reports and then click on the type of report you want to view.
If you want to keep a list of the current menu settings for reference purposes, print out a page with menu configuration before restoring factory settings. See Print page with menu settings on page 25 for more information.
If you want a more extensive method of restoring the default factory settings, run the Clear All Settings option. See 'Remove non-volatile memory' on page 76 for more information.
Browse the printer's control panel to:
> Institutions > > General Settings > > Factory Settings > > Recover Now
The Pincode Protection control panel allows you to restrict access to the menus on the printer's operating panel. To restrict access to the menus, create a PIN and assign it to each of the menu's.
1 Open a web browser and type the printer IP address in the address bar.
Manage printer 66 · >

2 Click on Institutions > Security > Pincode protection control panel.
3 Enter in the Create User PIN section or Create Administrator PIN.
4 Click on Modify (Change).
5 Select User PIN Secured, Administrator PIN Secure or Secure administrator and user pin code in a menu in the Managing Menus, Management or Access to Functions section.
6 Click on Send.
If you want to open a PIN-protected menu on the printer's control panel, please specify the PIN code.
Use Eco mode to quickly choose one or more ways to reduce the environmental impact of your printer.
1 Browse the printer's control panel to:
> Institutions > > General Settings > > Ecomode > > select the desired setting
Use Ecomode defaults for all settings. This setting supports the performance specifications for your printer.
Power Berke the energy consumption, especially when the printer is inactive.
Energy/paper Use all energy and paper saving settings.
Manage printer 67 · Option To

2 Press it.
In the dormancy mode, the printer uses almost no power.
1 Browse the control panel to:
> Institutions > > General Settings >
2 Press Press Sleep Button or Keep the sleep button pressed and then on .
3 Press Sleep Mode > .
With the time-out for slumber mode, you can set after how many minutes the save mode is enabled after a print job has been processed.
Use Embedded Web Server
1 Open a web browser and type the printer IP address in the address bar.
2 Click on Institutions > General Settings > Time-outs.
3 In the Time-out slumber mode menu, select the number of hours, days, weeks or months that the printer has to wait before switching to saving mode.
4 Click on Send.
Use printer settings on the computer
Depending on your operating system, you can use the Time-Out slumber mode menu via the Local Printer Settings Tool or through Printer Sets.
Manage printer 68

With Planning power mode, the user can set up when the printer switches to a saving position or to the Ready position.
Use Embedded Web Server
1 Open a web browser and type the printer IP address in the address bar.
2 Click on Institutions > General Settings > Planning current mode.
3 Select the current mode from the Action menu.
4 Select the time from the Time menu.
5 Select the day or days from the Day menu.
6 Click on Add.
Use printer settings on the computer (Windows only)
1 Open a web browser and type the printer IP address in the address bar.
2 Check that the virtual display is displayed in the upper left corner of the screen.
The virtual display works just like a real display on the printer's control panel.
1 Open a web browser and type the printer IP address in the address bar.
Manage Printer 69

2 Click on the tab Institutions > Security > Settings Secure Print.
4 Save the modified settings.
Use Ecomode to quickly choose one or more ways to reduce the environmental impact of your printer.
1 Browse the printer's control panel to:
> Institutions > Institutions > > General Settings > > Ecomode > > select the desired setting
Use Ecomode settings from Default values for all settings. This setting supports the performance specifications for your printer.
Limit current Energy consumption, especially when the printer is inactive.
Energy/paper Use all energy and paper saving settings.
2 Press it.
Manage printer 70 · Option Function

Use Silent mode to reduce printer noise.
1 Browse the printer's control panel to:
> Institutions > Institutions > > General Settings > > Silent Mode >
2 Select the desired setting.
From Limit the sound of the printer.
To use Default Settings.
3 Press it.
In the dormancy mode, the printer uses almost no power.
1 Browse the control panel to:
> Institutions > > Institutions > > General Settings >
2 Select Press Sleep Button or Keep the sleep button pressed and then press .
3 Press Sleep Mode > .
With the time-out for slumber mode, you can set after how many minutes the save mode is enabled after a print job has been processed.
Use Embedded Web Server
1 Open a web browser and type the printer IP address in the address bar.
Manage Printer 71 · Option To

2 Click on Institutions > General Settings > Time-outs.
3 In the Time-out slumber mode menu, select the number of hours, days, weeks or months that the printer has to wait before switching to saving mode.
4 Click on Send.
1 Browse the control panel to:
> Institutions > > Institutions > > General Settings > > Time-outs > >
2 Select the time when the printer waits after a print job is processed before setting slumber mode.
3 Press it.
Planning power mode allows you to set when the printer switches to a savings position or to the Ready Position.
Use Embedded Web Server
1 Open a web browser and type the printer IP address in the address bar.
2 Click on Institutions > General Settings > Planning current mode.
3 Select the current mode from the Action menu.
4 Select the time from the Time menu.
5 Select the day or days from the Day menu.
6 Click on Add.
Manage printer 72 · Use the control panel · Sleep timeout >

If you want to save energy or cannot read the display correctly, adjust the brightness settings.
Use Embedded Web Server
1 Open a web browser and type the printer IP address in the address bar.
2 Click on Institutions > General Settings.
3 In the Brightness box, specify the desired percentage for the display.
4 Click on Send.
If you want to keep a list of the current menu settings for reference purposes, print out a page with menu configuration before restoring factory settings. See 'Print page with menu settings' on page 26 for more information.
If you want a more extensive method of restoring the default factory settings, run the Clear All Settings option. See 'Remove non-volatile memory' on page 76 for more information.
Browse the control panel to:
> Institutions > Institutions > > General Settings > > Factory Settings > > Now
Save energy by reducing the number of minutes that the printer waits before switching to sleep mode.
1 Browse the control panel to:
> Institutions > > General Settings > > Time-outs > > Sleep Mode >
2 Select the number of minutes that the printer is waiting for before switching to sleep mode.
Manage printer 73 · recover >

3 Apply the changes.
Manage Printer 74

Use the locking function
The printer has a locking function. At the specified location, confirm a security lock compatible with most laptops to lock the printer in place.


The printer contains different types of memory that can store device and network settings and user data.
Volatile Memory The printer uses standard RAM (Random Access Memory) to buffer user data during simple printing and copying tasks.
The printer may use two types of non-volatile memory: EEPROM and NAND (flash-remember). Both types are used to store the operating system, device settings and network data.
In the following cases, you must delete the contents of your printer memory:
A power source is needed to store information in the printer's volatile memory (RAM). Disable the printer if you want to delete the buffered data.
Secure printer 75 · Memory Type Description · Non-volatile memory

1 Turn off the printer.
2 Hold the control panel and arrow pressed to the right while turning on the printer. Do not release the buttons until the Configuration menu appears.
3 Press the arrow keys until Clear All Settings is displayed and press .
During this process, the printer will be restarted several times.
4 Press the arrow keys until Exit Config Menu (Close Menu Configuration) appears and press
then on .
The printer will be switched off and turned on again and returns to normal operating mode.
Perform the following steps to clear individual settings, device and network settings and security settings as well as embedded solutions:
1 Turn off the printer.
2 Hold 2 and 6 press the keypad while you enable the printer. Do not release the buttons until the screen is displayed with the progress bar.
The printer executes the boot cycle, after which the Configuration menu is displayed. When the printer is fully heated, a list of functions appears on the printer display.
3 Press the arrow up or down to Clear All Settings is displayed.
During this process, the printer will be restarted several times.
4 Go to:
Prev > Quit Configuration Menu
The printer will be switched off and turned on again and returns to normal operating mode.
Secure Printer 76

In environments where highly sensitive information is used, additional measures may need to be taken to ensure that confidential data on the printer's hard drive are not accessible to unauthorised persons. For more information, please visit the Lexmark security web page or consult the administrator's manual Embedded Web Server, security on http://support.lexmark.com
Secure printer 77

Printer Menu Information 78
MS312 and MS317: menu overview
Paper Menu Reports Network/Ports
U-loader configuration Different size Paper structure
Network Settings Page1
Print preview Asset report Print example
Paper Settings Custom Types
Set date and time General settings Print Settings
1 Depending on the printer installation, this menu item is displayed as a page with network settings or Installation-page network [x].
2 Depending on the printer configuration, this menu option is displayed as a default network or Network [x].
Paper Menu Reports Network/Ports
Network Settings Page1
Other Size Paper Structure Paper Weight
Print fonts
Default parallel Settings SMTP

Printer Menu Information 79
Print confidentially Log file security checker
Print all manuals print quality
Set date and time
Help print Help print mat.
Print failure manual Menu Folder
Help transport Help with supplies
1 Depending on the printer installation, this menu item is displayed as a page with network settings or Installation-page network [x].
2 Depending on the printer configuration, this menu option is displayed as a default network or Network [x].
Set a default paper source for all printing tasks.
Loader [x] U-loader Manual paper input Manual envelope entry

Printer Menu Information 80
Specify the size of the paper in each tray.
A4 A5 A6 JIS-B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal
Specify the type of paper in each tray.
Normal paper Transparency Circuit Labels Bank post Letterhead Preprinted Coloured paper Light Paper Heavy Paper Raw/cotton Customized [x]
Specify the size of the paper in the universal loader.
A4 A5 A6 JIS B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal 7 3/4 -envelope 9-envelop DL -enfold C5 envelope B5 envelope Other envelope

Printer Menu Information 81
Specify the type of paper in the universal charger.
Normal Paper Cardboard Transparency Circuit Labels Bank Post Envelope Raw Envelopes Preprinted Coloured paper Light Paper Heavy Paper Crude/cotton Customized [x]
Paper size handm. import
Specify the paper format to be placed manually.
A4 A5 A6 JIS B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal
Paper type handm. import
Specify the type of paper to be placed manually.
Normal Paper Cardboard Transparency Circuit Labels Bank post Letterhead Preprinted Coloured paper Light Paper Heavy Paper Raw/cotton Customized [x]
Select Function · Type of U-loader

Printer Menu Information 82
Envelope size handm. import
Specify the envelope format you are manually placing.
7 3/4 -Envelope 9-envelope 10-enfold DL -Enfold C5-enpack B5-Envelopes Other Envelope
Envelope type of handm. import
Specify the type of envelope you need to be placed manually.
Envelope Raw Envelopes Custom [x]
Set a default paper source for all printing tasks.
Loader [x] Universe charger Manual paper input Manual envelope entry
Specify the size of the paper in each tray.
A4 A5 A6 JIS B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal

Printer Menu Information 83
Specify the type of paper in each tray.
Normal paper Transparency Circuit Labels Bank post Letterhead Preprinted Coloured paper Light Paper Heavy Paper Raw/cotton Customized [x]
Specify the paper format in multifunctional input.
A4 A5 A6 JIS B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal 7 3/4 envelope 9-envelope 10-enfold DL Envelope C5 Envelop B5 Enfold Other
Option To · Type of tray [x] · Universal charger format

Printer Menu Information 84
Specify the type of paper in the universal charger.
Normal Paper Cardboard Transparency Circuit Labels Bank Post Envelope Raw Envelopes Preprinted Coloured paper Light Paper Heavy Paper Crude/cotton Customized [x]
Paper size handm. import
Specify the paper format to be placed manually.
A4 A5 A6 JIS B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal
Paper type handm. import
Specify the type of paper you manually place.
Normal Paper Cardboard Transparency Circuit Labels Bank post Letterhead Preprinted Coloured paper Light Paper Heavy Paper Raw/cotton Customized [x]
Option To · Universal Charger Type

Printer Menu Information 85
Envelope size handm. import
Specify the envelope format you are manually placing.
7 3/4 envelope 9-envelope 10-enfold DL Envelope C5 Envelopes B5 Enfolding Other
Envelope type of handm. import
Specify the type of envelope you manually place.
Envelope Raw Envelopes Custom [x]
Determine when the printer must select paper that is placed in the universal loader.
Replace a specified paper format if the desired paper size is not available.
From Statement/A5 Letter/A4 All in List
Specify the relative structure of the placed normal paper.

Printer Menu Information 86
Specify the relative structure of the placed cardboard.
Specify the relative structure of the placed transparents.
Strick. kollen. pap.
Specify the relative structure of the placed recycled paper.
Specify the relative structure of the labels placed.
Specify the relative structure of the placed bank note.
Specify the relative structure of the envelopes placed.
Specify the relative structure of raw envelopes.
Specify the relative structure of the letterhead paper placed.
Specify the relative structure of the preprinted paper placed.
Specify the relative structure of the placed coloured paper.
Specify the relative structure of the paper placed.

Printer Menu Information 87
Specify the relative structure of the paper placed.
Specify the relative structure of the cotton paper placed.
Specify the relative structure of the attached paper.
Specify the relative weight of the normal paper placed.
Specify the relative weight of the cardboard placed.
Specify the relative weight of the placed transparencies.
Weight kringl.dap.
Specify the relative weight of the recycled paper placed.
Specify the relative weight of the labels placed.
Specify the relative weight of the bank note issued.
Specify the relative weight of the envelopes placed.

Printer Menu Information 88
Specify the relative weight of the rough envelopes placed.
Specify the relative weight of the letterhead paper placed.
Specify the relative weight of the preprinted paper placed.
Specify the relative weight of the coloured paper placed.
This indicates that the weight of the paper placed is light.
This indicates that the weight of the paper placed is heavy.
This gives you the relative weight of the cotton paper or raw paper placed.
Specify the relative weight of the adjusted paper placed.
Kringl.dap. places
Determine and set that all printing tasks are printed in double-sided form using Kringlooppaper.

Printer Menu Information 89
Determine and set that all printing tasks are printed in two sides with Bankpost as paper type.
Determine and set that all printing tasks are printed double-sided with Letterhead as paper type.
Determine and set that all printing tasks are printed double-sided with Pre-printed paper.
Determine and set that all printing tasks are printed with Colored as paper type double-sided.
Determine and set that all printing tasks are printed with Light as paper type double-sided.
Determine and set that all printing tasks are printed double-sidedly with Heavy paper.
Determine and set that all printing tasks are printed double-sided using Custom [x] as a paper type.
Linking a type of paper or special material to an appropriate name [x].
Paper Cardboard Transparent Raw/cotton Labels Envelope

Printer Menu Information 90
Specify a type of paper as in other menus the circle paper setting is selected.
Paper Cardboard Transparent Raw/cotton Labels Envelope Cotton
Give up the unit of measurement.
Set the width of the upright direction.
Set the height of the upright direction.
Specify the input direction if paper can be loaded in both directions.
Short Side Long Side

Printer Menu Information 91
Print report with information about the paper in the loading, installed memory, total number of pages, alarms, time-outs, language on the control panel, TCP/IP address, supply status, network connection status, and other information.
Print report with printer statistics, such as data on supplies and printed pages.
Pag. Network setup. Print a report with information about the network printer settings, such as TCP/IP address.
Profile List A list of profiles prints stored on this printer.
Print a report of all available fonts for the printer language currently set in the printer.
Print Directory Print a list of all sources stored on an optional flash memory card.
Assets report Print a report with printer asset data, including the serial number and model name.
Print a report with a summary of all recorded events.
The menus in this section are only displayed on network printers or printers connected to print servers.
Automatically [list of available network cards]
![Page 92 of the Lexmark MS415 user manual — Default Network or Network Menu [x]](/cdn/reader/11/11c90aaaab7020db2ca4325302eeffdfad3e10338dfcaae2d5335733926fabfc/images/page-92.webp?w=400)
Information about the printer menus 92
This configures the printer to automatically switch to PCL emulation if required by a printing job, regardless of default printer language.
This configures the printer to automatically switch to PS emulation if required by a printing job, regardless of default printer language.
Set whether the printer should perform the special processing for bidirectional communication, as defined in the specifications of the NPA protocol.
Set the size of the network input buffer.
Disabled Automatic 3 KB to [maximum allowed size]
Set printer to process binary PostScript printing tasks for Macintosh.

Printer Menu Information 93
Set default network setting or Network [x]
Display and configure the printer's network settings.
Reports Network Card TCP/IP IPv6 Wireless AppleTalk
You can open the menu as follows:
Printer setting page Print a report with information about the network printer's settings, such as
TCP/IP address.
You can open the menu in one of the following ways:
Specify network mode.
Specify the wireless network usage standard for the wireless.
802.11b/g 802.11b/g/n
Choose Network Select a available network for the printer.
Display signal strength Display the quality of wireless connection.
Display security mode Display the wireless network encryption method.
![Page 94 of the Lexmark MS415 user manual — Menus Default Network or Network [x]](/cdn/reader/11/11c90aaaab7020db2ca4325302eeffdfad3e10338dfcaae2d5335733926fabfc/images/page-94.webp?w=400)
Information about the printer menus 94
This sets the Ethernet connection of the printer to a saving mode.
This configures the printer to automatically switch to PCL emulation if required by a printing job, regardless of default printer language.
This configures the printer to automatically switch to PS emulation if required by a printing job, regardless of default printer language.
Set whether the printer should perform the special processing for bidirectional communication, as defined in the specifications of the NPA protocol.
Set the size of the network input buffer.
Automatically 3 KB to [maximum allowed size]

Information about the printer menus 95
Set printer to process binary PostScript printing tasks for Macintosh.
Set default network setting or Network [x]
Display and configure the printer's network settings.
Reports Network Card TCP/IP IPv6 Wireless AppleTalk
Printer setting page Print a report with information about the network printer's settings, such as
TCP/IP address.
Wi‑Fi Protected Setup (WPS)
Set up a wireless network and enable network security.
Start method with push button Starting method with pincode
Automatically determine which connection method uses an access point with WPS: Start a pushbutton or start a PIN.
Specify network mode.

Information about the printer menus 96
Specify the wireless network usage standard for the wireless.
802.11b/g 802.11b/g/n
Choose Network Select a available network for the printer.
Display signal strength Display the quality of wireless connection.
Display the wireless network encryption method.
Display the connection status of the network card.
Show map speed Display the speed of an active network card.
Show the network addresses.
Timeout for task Set 0-255 seconds After how many seconds a print job specified over the network can be cancelled.
Enable the front pages.
Set host name Set the host name.

Information about the printer menus 97
IP Address View or modify the current TCP/IP address.
Netmask View or modify the current TCP/IP netmask.
Gateway View or modify the current TCP/IP gateway.
Specify the DHCP address and parameter allocation.
Specify the network zero configuration setting.
Enable the built-in FTP server, which allows you to send files to the printer via file transfer protocol.
Enable the built-in web server (Embedded Web Server). If enabled, the printer can be remotely checked and managed via a web browser.
WINS Server Address View or change the current WINS server address.
View or modify the current DDNS setting.
View or modify the current mDNS setting.
DNS Server Address View or modify the current DNS server address.
Backup DNS server address View or modify the backup DNS server address.
View or modify the current HTTPS setting.
You can open the menu in one of the following ways:

Printer Menu Information 98
Enable IPv6 (Internet protocol version 6) on the printer. IPv6 uses larger numbers to create IP addresses.
Set whether the network adapter accepts IPv6 addresses automatically configured by a router.
Set hostname* Set the host name.
Show Address* Display the current IPv6 addresses.
Show router address* Display the current router address.
Enable DHCPv6 on the printer.
* You can only change these settings via the Embedded Web Server.
Set the printer to automatically switch to PCL emulation if required by a print job on the USB port, regardless of default printer language.
Set the printer to automatically switch to PS emulation if required by a print job on the USB port, regardless of default printer language.
Set whether the printer should perform the special processing for bidirectional communication, as defined in the specifications of the NPA protocol.

Printer Menu Information 99
Set the size of the USB input buffer.
Disabled Automatic 3 kB to [maximum allowed size]
Set printer to process binary PostScript printing tasks for Macintosh.
Set up network address data for an external print server.
yyy.yyy, yy, yo
Set up network mask data for an external print server.
yyy.yyy, yy, yo
Set up gateway data for an external print server.
yyy.yyy, yy, yo
Set printer to automatically switch to PCL emulation if required by a printing job on a serial port, regardless of the default printer language.

Printer Menu Information 100
Set printer to automatically switch to PS emulation if required by a printing job on a serial port, regardless of the default printer language.
Set whether the printer should perform the special processing for bidirectional communication, as defined in the specifications of the NPA protocol.
Set the parallel input buffer size.
Disabled Automatic 3 KB to [maximum allowed size]
This enables you to switch on bidirectional communication via the parallel port.
Set protocol for the parallel port.

Printer Menu Information 101
Determine whether the printer honours printer hardware initialization requests from the computer.
Determine how the parallel port data is sampled at the front or back of the strobe.
Set printer to process binary PostScript printing tasks for Macintosh.
Set up network address data for an external print server.
yyy.yyy, yy, yo
Set up network mask data for an external print server.
yyy.yyy, yy, yo
Set up gateway data for an external print server.
yyy.yyy, yy, yo
You can open the menu as follows:
Toggle support for AppleTalk.
Show Name Display the assigned AppleTalk name.
Show Address Display the assigned AppleTalk address.
Display a list of AppleTalk zones available on the network.
[list of zones available on the network]

Printer Menu Information 102
Primary SMTP gateway Specify data for the SMTP server gateway and port.
5.7.330 Specify after how many seconds the server ends an attempt to send email.
Answer Address Specify a reply address of up to 128 characters in email messages sent by the printer.
Set printer to use SSL for additional security when connecting to the SMTP server.
Specify which type of user authentication is required for print permissions.
No authentication required Login/Normal CRAM-MD5 Digest-MD 5 NTLM Kerberos 5
E-mail initiated by the device
Specify which references are used when communicating with the SMTP server. Some SMTP servers require references to send email.
Use None SMTP References for Device

Printer Menu Information 103
Max. invalid PIN
Limit the number of times an invalid PIN code can be entered.
Limit the duration of a secure printing job remaining in the printer before removing the task.
From 1 hour 4 hours 24 hours 1 week
Time-limit for repeated tasks
Set a time limit for saving print jobs.
From 1 hour 4 hours 24 hours 1 week
Time-limit for controlled tasks
Set a time limit for storing print jobs that require verification.
From 1 hour 4 hours 24 hours 1 week
Time-out for reserved tasks
Set a time limit for saving print jobs that are printed at a later date.
From 1 hour 4 hours 24 hours 1 week
Option To · Uit 2–10 · False time secure task

Information about printer menus 104
Specify whether or not to delete control log files.
Remove Now Do Not Delete
Please specify whether or not to create control log files and how they are created.
Yes No To create external system log
No Yes External system log for viewing
0.0.lo23 Ernst of logging is done
Current date and time Display the current printer date and time settings.
Manual Date & Time Set
Give the date and time.
Select the time zone.
Set the printer to use the appropriate start and end time of summer time according to the printer's time zone setting.
Enable the network time protocol, which synchronizes devices' clocks in a network.

Printer Menu Information 105
Select the language of the text on the display.
English Francais Deutsch Italiano Espanol Dansk Norsk Dutch Swedish Portuguese Suomi Russian Polski Greek Magyar Turkce Cesky Simplified Chinese Traditional Chinese Korean Japanese
Display estimates of the supplies on the control panel, Embedded Web Server, menu settings and statistics reports from the device.
Show estimates Do not show estimates
Minimize the use of energy, paper or special printing material.
From Energy Energy/paper Paper
Minimize the printer's sound.
Run the installation wizard.

Printer Menus Information 106
This will specify the size units for paper formats.
VS. Metric
This will set after how many minutes the save mode is enabled after printing a print job.
Print a task while the display is disabled.
Print while the display is off
Print while the display is off Allow Display to be displayed during printing
Set the time to wait for the printer before setting the dormancy mode.
Disabled 1-3 hours 6 hours 1-3 days 1-2 weeks 1 month
Set the printer to slumber mode even if there is an active Ethernet connection.
Snooze timeout on connection
Do not enable sleep mode slumber
Set after how many seconds the control panel returns to working mode Done.

Information about the printer menus 107
This sets the time in seconds that the printer is waiting to receive a message for end task before the rest of the task is cancelled.
Set how many seconds the printer waits for further data before canceling the print job.
Set the printer to restart if an error occurs.
Restart at inactive mode Always restart Never restart Limit Auto restart
This will give the printer an automatic print order if certain offline situations are not resolved within the specified time frame.
Specify whether to reprint the printer's blocked pages.
Set the printer to automatically check if paper is stuck.

Printer Menu Information 108
Print a page that might not otherwise be printed.
Determine how the printer reacts in inactive mode when briefly pressing the sleep button.
Do nothing Sleeping Sleep
Determine how the printer reacts in inactive mode when pressing a long sleep button.
Do nothing Sleeping Sleep
Use the printer's default factory setting except for Network and Port menu settings.
Do Not Restore Now Recover
Select a custom homepage message that is displayed as alter native views of the printer status.
From IP address Hostname Contact person Location Name of configurationless program Custom text 1

Printer Menu Information 109
Select the language of the text on the display.
English Francais Deutsch Italiano Espanol Dansk Norsk Dutch Swedish Portuguese Suomi Russian Polski Greek Magyar Turkce Cesky Simplified Chinese Traditional Chinese Korean Japanese
Display estimates of the supplies on the control panel, Embedded Web Server, menu settings and statistics reports from the device.
Show estimates Do not show estimates
Minimize the use of energy, paper or special printing material.
From Energy Energy/paper Paper
Minimize the printer's sound.
Run the installation wizard.

Information about the printer menus 110
This will specify the size units for paper formats.
VS. Metric
Change the icons displayed in the start screen. Choose from the following options for each icon:
Change language Find wait jobs Watch tasks USB drive
This sets an alarm signal that is played when the user has to intervene.
Select one of the following options for individual alarms:
From One Time Continuous
This will set after how many minutes the save mode is enabled after printing a print job.
Print a task while the display is disabled.
Print while the display is off
Print while the display is off Allow Display to be displayed during printing
Set the time to wait for the printer before setting the dormancy mode.
Disabled 20 minutes 1-3 hours 6 hours 1-3 days 1-2 weeks 1 month

Printer Menu Information 111
Set the printer to slumber mode even if there is an active Ethernet or faxer binding.
Snooze timeout on connection
Do not enable sleep mode slumber
Set after how many seconds the control panel returns to working mode Done.
This sets the time in seconds that the printer is waiting to receive a message for end of task before canceling the rest of the print job.
Set how many seconds the printer waits for further data before canceling the print job.
Set the printer to restart if an error occurs.
Restart at inactive mode Always restart Never restart
Set the number of times auto restarting that the printer can run.
Auto Restart Limit
This will give the printer an automatic print order if certain offline situations are not resolved within the specified time frame.
Disabled 5-255 sec.
Specify whether to reprint the printer's blocked pages.

Printer Menu Information 112
Set the printer to automatically check if paper is stuck.
Print a page that might not otherwise be printed.
Information sent to Lexmark
Send anonymous information about the use of the device to Lexmark.
Use of supplies and pages (anonymous)
Information sent to Lexmark
Send anonymous information about the operation and errors of the device to Lexmark.
Information sent to Lexmark
Set the time to send anonymous information to Lexmark.
Start Sending Stop Sending
Determine how the printer reacts in inactive mode when briefly pressing the sleep button.
Do nothing Sleeping Sleep
Determine how the printer reacts in inactive mode when pressing a long sleep button.
Do nothing Sleeping Sleep
Restore the printer's default settings.
Do Not Restore Now Recover
Export configuration files to a flash drive.

Printer Menu Information 113
Set the default printer language.
Set the logical and physical printable area.
Set the storage location for downloads.
Specify what the printer should do with temporary downloads, such as fonts and macros stored in RAM when the printer gets a print job that requires more memory than is available.

Printer Menu Information 114
Configure or double-sided printing is used for all print jobs by default.
1 Click on Stock > Print. 2 Click on Properties, Preferences, Options or Set.
If you are using Macintosh:
1 Choose Archive > Print. 2 Adjust the settings via the Print dialog box and the pop-up menus.
Set how to bind and print double-sided printed pages.
Long Edge Short Edges (Short silk)
1 January 1999 Specify a standard number of copies for each job.
Set whether to insert empty pages into a print job.
Do Not Print
Keep the pages of a print job in order when printing multiple copies.
(1,1,1) (2,2,2) (1,2,3) (1,2,3)
Set whether to insert empty separation sheets.
On Between copies Between tasks Between pages
Specify the source of paper for the separation sheets.

Printer Menu Information 115
Multiple page images on one side of a sheet of paper printing.
At 2 per sheet 3 per sheet 4 per sheet 6 per sheet 9 per sheet 12 per sheet 16 per sheet
Specify the position of multiple page images when using Paper Saving.
Horizontal (Horizontal) Reverse horizon. Vertical Reverse
Set a multi-page document to print.
Print a border when paper saving is used.
Specify the quality of the scan in dpi (dots per inch).
300 dpi 600 dpi 1200 dpi Image quality 1200 Image quality 2400
This allows more pixels to print in clusters for better brightness, to improve images horizontally or vertically or to improve fonts.
From Fonts Horizontal Vertical Both directions
1-10 Make printing lighter or darker.

Printer Menu Information 116
Enable a printing mode specially designed for files with precise details, such as architectural drawings, maps, circuit diagrams and flow meters.
Automatically adjust the contrast enhancement applied to the printed images.
This makes printing lighter or darker. You can save toner by making lighter prints.
‐6 to 6
0-5 This adjusts the contrast of the printed objects.
Print a page with error information, including XML markup errors.
Print a page containing the PostScript error.
Disable the SysStart file.

Printer Menu Information 117
Set the order in which the printer searches fonts.
Format the flash memory.
Tracking the source of a printing problem.
Estimate the coverage rate for toner on a page. The estimate is printed on a separate page at the end of each print job.

Printer Menu Information 118
Set the font set used in the Font Name menu.
Resident Download Flash Memory All
Display a specific font and the option in which it was saved.
Display the symbol set for each font name.
Setl. PCL emulation
Change the point size of scalable, typographic fonts.
Setl. PCL emulation
Set font pitch for scalable fixed-tread fonts (monospaced).

Printer Menu Information 119
Setl. PCL emulation
Set the print mode of text and images on the page.
Setl. PCL emulation
Specify the number of lines printed on each page.
Setl. PCL emulation
Set the printer to A4 paper format.
198 mm 203 mm
Setl. PCL emulation
Specify whether the printer should automatically give a hard return (CR) after command to go to a new line (LF).
Automatic HR after NR
Setl. PCL emulation
Whether the printer automatically executes a new line (NR) after a hard return command (HR).
Automatic NR after HR
Tray No modify
Configure the printer to work with printer software or applications that have defined other loading as a paper source.
From No 0.0.2001 Value tray [x]
Out of No 0.0.2001 Value handm. import
From No 0.0.2001 Value envelope (handm.)

Printer Menu Information 120
Tray No modify
Display the default setting for each input tray.
U-loader standard inst. = 8 T1 Std. inst. = 1 T1 Std. inst. = 4 T1 Std. inst. = 5 T1 Std. inst. = 20 T1 Std. inst. = 21 Std. inst. env. = 6 Std. inst. hnd. inv. = 2 Std. inst. env.inv. = 3
Tray No modify
Reset all drawer and input allocations to the default factory settings.
Set whether the printer creates a log file for the received print tasks.
Task administration tools Print log files and delete or export them to a flash drive.
Set how often a log file is created.
Action log file at end of frequency
Set how the printer reacts at the end of the specified frequency.
No Current Log File Emailing and Delete Current Log file E-mailing and deleting Place current log file Post and delete current logfile
Log level almost full
Specify how large the log file can be before running action at Actionlog at almost full.
From 1-49 for optional flash memory cards

Printer Menu Information 121
Action log at almost full
Set how the printer reacts when flash memory is almost full.
No Current Log File Emails Current Log file email and delete Oldest log file email & remove Place current log file Place current Log file and delete oldest logfile Place and delete deleted existing log file Delete oldest logs file Delete all log files Delete everything except present log file
Set how the printer reacts when maximum flash memory is reached (100 MB).
No Current Log File Email and Remove Oldest log file email and delete Place and Delete Current Log file Post and Remove Newest logfile Delete current log file Delete oldest log files Delete all log files Remove everything except present log file
URL for place log files Set where the log files are placed by the printer.
Email address for sending log files Specify the email address to which the task-admini log files are sent.
Prefix logfile Specify the desired prefix for the name of the log file.
Format the flash memory.

Printer Menu Information 122
Tracking the source of a printing problem.
Estimate the coverage rate for toner on a page. The estimate is printed on a separate page at the end of each print job.
Customize page contents to the size of the selected paper.
Print notes in a PDF file.
Set the font set used in the Font Name menu.
Resident Download Flash Memory All
Display a specific font and the option in which it was saved.

Printer Menu Information 123
Display the symbol set for each font name.
Setl. PCL emulation
Change the point size of scalable, typographic fonts.
Setl. PCL emulation
Set font pitch for scalable fixed-tread fonts (monospaced).
Setl. PCL emulation
Set the print mode of text and images on the page.
Setl. PCL emulation
Specify the number of lines printed on each page.
Setl. PCL emulation
Set the printer to A4 paper format.
198 mm 203 mm

Printer Menu Information 124
Setl. PCL emulation
Specify whether the printer should automatically give a hard return (CR) after command to go to a new line (LF).
Automatic HR after NR
Setl. PCL emulation
Whether the printer automatically executes a new line (NR) after a hard return command (HR).
Automatic NR after HR
Tray No modify
Configure the printer to work with printer software or applications that have defined other loading as a paper source.
From No 0.0.2001 Value tray [x]
Out of No 0.0.2001 Value handm. import
From No 0.0.2001 Value envelope (handm.)
Tray No modify
Display the default setting for each input tray.
U-loader standard inst. = 8 T1 Std. inst. = 1 T2 Default Setting = 4 T3 Std.int. = 5 T4 Default Setting = 20 T5 Std. inst. = 21 Std. inst. env. = 6 Std. inst. hnd. inv. = 2 Std. inst. env.inv. = 3
Tray No modify
Reset all drawer and input allocations to the default factory settings.

Printer Menu Information 125
Joanna MT Letter Gothic Lubalin Graph Marigold MonaLisa Recut Monaco New CenturySbk New York Optima Oxford Palatino Stamp Garamond Taffy TimesNewRoman Univers Zapf Chancery NewSansMTCS NewSansMTCT New SansMTJA NewSensMTKO
Set the default font for HTML documents.
Albertus MT Antique Olive Apple Chancery Arial MT Avant Garde Bodoni Bookman Chicago Clarendon Cooper Black Copperplate Coronet Courier Eurostile Garamond Geneva Gill Sans Goudy Helvetica Hoefler Text Intl CG Times Intl Courier Intl Univers
1.1.7255 pt Set the default font size for HTML documents.
1.1.7400% Adjust the default font for HTML documents.
Set the print mode for HTML documents.
8.10.255 mm Set the page margin for HTML documents.

Printer Menu Information 126
Configure or print backgrounds in HTML documents.
Autom. change.
Select optimal values for paper size, scale and print mode.
Turn two-colored black and white images.
Adjust the image size so it fits the selected paper format.
Anchor Left Top corner Most Similar Center Anchors Height/width Match Adjust height Adjust width
Set image print position.
Standing facing standing facing facing facing face facing facing
The Help menu consists of a set of help pages stored in the printer as PDFs. These contain information about the printer usage and how to execute print jobs.
English, French, German and Spanish translations are stored on the printer. Other translations are available on http://support.lexmark.com.
Print all manuals Print All manuals.
Print quality Information on solving problems with print quality printing.
Print guide Information on the placement of paper and other special printing material.
Print Material Guide A list of supported paper formats for the different input loadings
prints.

Printer Menu Information 127
Print print failure guide Print printing error solving information.
Print a list of the menus and settings on the printer control panel.
Print information Help in searching for additional information.
Connecting Guide Print information about connecting the printer via USB (local) or a network.
Transport Manual Print instructions for moving the printer.
Help with supplies Print product numbers for ordering supplies.
Option To

Preventing paper failures
Paper is correctly placed Paper is not correctly placed

Resolve paper failures 128




Paper failures remedy 129

NOTE: HOT SURFACE: The inside of the printer can be hot. To avoid injury, you should cool a hot surface before touching it.
1 Open the front door.


2 Remove the toner cartridge.

3 Remove the image processing unit.

Paper failures remedy 130


4 Remove the stuck paper.


5 Place the image processing unit.

Resolve paper failures 131

6 Place the toner cartridge.


7 Close the front valve.
8 Press the control panel .
1 Open the tailgate.
NOTE: HOT SURFACE: The inside of the printer can be hot. To avoid injury, you should cool a hot surface before touching it.

2 Remove the stuck paper.
Paper failures remedy 132

3 Close the tailgate.
4 Press the control panel .
1 Remove the stuck paper.

2 Press the control panel .
Paper failures remedy 133

1 Remove the drawer.

2 Remove the stuck paper.


3 Put the drawer back.
Resolve paper failures 134

1 Remove the drawer.
2 Remove the stuck paper.

3 Put the drawer back.
4 Press the control panel .
1 Remove the stuck paper.
Resolve paper failures 135

2 Press the control panel .
Resolving paper failures 136

NOTE: DANGER OF ELECTRIC SHOCKS: To avoid the risk of electric shocks, pull the power cord plug out and unplug all cables connected to the printer before cleaning the outside of the printer.
1 Turn off the printer and pull the plug on the power cord of the printer from the socket.
2 Remove all the paper from the standard tray and multifunctional input.
3 Clean the printer with a soft brush or vacuum cleaner to remove dust, ink ribbon and pieces of paper inside and around the printer.
4 Wipe the outside of the printer with a damp, soft, lint-free cloth.
5 Connect the power cord plug to the socket and turn on the printer.
PLEASE NOTE: RISK OF INJURY: To avoid the risk of electric shocks or fire, you need to connect the power cord directly to a grounded outlet close to the product and which is easily accessible.
1 Open a web browser and type the printer IP address in the address bar.
2 Click on Device status.
Maintaining printer 137

Depending on the printer model, navigate to one of the following locations:
The estimated number of pages remaining is based on the printer's recent print history. The accuracy of the data can vary considerably and depends on many factors, such as actual document content, print quality settings and other printer settings.
The accuracy of the estimated number of pages remaining may decrease when actual printing consumption differs from past print consumption. Please take this variable accuracy level into account before purchasing or replacing supplies based on the estimate. Until adequate print history is obtained, the first estimates assume that supplies are consumed based on International Organization for Standardisation* and page content.
* Displayed average cartridge efficiency (black) according to ISO/IEC 19752.
In the U.S. Please call to order supplies +1-800-539-6275 for information about authorised dealers of Lexmark supplies in your area. In other countries or regions you will go to www.lexmark.com, or contact the store where you bought the printer.
Your Lexmark printer works best with original Lex Mark supplies and parts. Using supplies or components from manufacturers other than Lexmark may have a negative impact on the performance, reliability or lifetime of the printer and image processing parts of the device. The use of supplies or parts from other manufacturers may affect your warranty. Damage caused by the use of supplies or parts from other manufacturers is not covered by the warranty. All life indicators are designed to function with the supplies and parts Lexmark. If you use supplies or parts from other manufacturers, this may lead to unpredictable results. The use of image processing components longer than the intended life span can damage your Lexmark printer or its parts.
Maintaining printer 138


* This supply is only supported on the MS415 model.
Go www.lexmark.com/regions for more information on countries in the individual regions.

* This supply is only supported on the MS415 model.
Go www.lexmark.com/regions for more information on countries in the individual regions.

* This supply is only supported on the MS417.
Go www.lexmark.com/regions for more information on countries in the individual regions.
Printer maintenance 139

High-performance toner cartridge 51B0HA02
1 This supply is only supported on the printer model MS317.
2 This supply is only supported on the printer model MS417.
Go www.lexmark.com/regions for more information on countries in the individual regions.
Extremely low print coverage over a longer period can cause parts of the image processing unit to break before the toner is exhausted in the tone cartridge.
Please refer to the instructions at the supply for more information about replacing the image processing unit.
Article name Lexmark return programme for toner cartridges Normal
Store supplies in a cool, clean room. Supplies should always be stored upright in the original package until they are used.
Do not expose the printer's uploads to:

1 Press the button on the right side of the printer and open the front valve.
2 Pull the toner cartridge out of the handle.
3 Unpack the toner cartridge and remove all packaging material.
4 Shake the new cartridge to distribute the toner evenly.

5 Install the toner cartridge in the printer by aligning the arrows on the side of the cartridge with the arrow on the rails inside the printer.
Maintaining printer 141

6 Close the front valve.
1 Press the button on the right side of the printer and open the front valve.
2 Pull the toner cartridge out of the handle.
Maintaining printer 142

3 Lift the green handle and pull out the image processing unit.

4 Unpack the new image processing unit and shake it.

5 Remove all packaging material from the image processing unit.
Maintaining printer 143

6 Install the image processing unit in the printer by aligning the arrows on the side of the image handling unit with the arrow on the rails inside the printer.
7 Install the toner cartridge in the printer by aligning the arrows on the side of the cartridge with the arrow on the rails inside the printer.


8 Close the front valve.
PLEASE NOTE: RISK OF INJURY: The printer weighs more than 18 kg (40 lb) and must be lifted by two or more trained staff.
PLEASE NOTE: RISK OF INJURY: Use only the power cord supplied with this product or a replacement component approved by the manufacturer to prevent fire or electric shocks.
PLEASE NOTE: RISK OF INJURY: Follow these guidelines when moving the printer to prevent injury or damage of your printer:
Printer maintenance 144

If you want to transport the printer, use the original packaging or call the store where you bought the printer for the required packing materials.
Maintaining printer 145
![Page 146 of the Lexmark MS415 user manual — Change [paper source] to [adapted series] places [print mode]](/cdn/reader/11/11c90aaaab7020db2ca4325302eeffdfad3e10338dfcaae2d5335733926fabfc/images/page-146.webp?w=400)
Printer Messages
Executable drawer full. Remove paper.
Remove the paper stack from the standard drawer.
Try one or more of the following solutions:
Try one or more of the following solutions:
> Institutions > > Print Settings > > Extra Menu > > Format Flash >
> Yes > • Install additional printer memory.
Try one or more of the solutions:
Troubleshooting 146

Try one or more of the solutions:
Try one or more of the solutions:
Try one or more of the solutions:
Try one or more of the following solutions:
Try one or more of the following solutions:
Troubleshooting 147
![Page 148 of the Lexmark MS415 user manual — Network error, port [x]](/cdn/reader/11/11c90aaaab7020db2ca4325302eeffdfad3e10338dfcaae2d5335733926fabfc/images/page-148.webp?w=400)
Try one or more of the following solutions:
> Institutions > > Print Settings > > Extra Menu > > Format Flash >
> Yes > • Use a flash memory card with a larger capacity.
Try one or more of the following solutions:
Try one or more of the following solutions:
Try one or more of the solutions:
Troubleshooting 148
![Page 149 of the Lexmark MS415 user manual — Rear USB port disabled [56]](/cdn/reader/11/11c90aaaab7020db2ca4325302eeffdfad3e10338dfcaae2d5335733926fabfc/images/page-149.webp?w=400)
Try one or more of the solutions:
Try one or more of the following solutions:
Restart printer. Check last task.
Press the printer's control panel to delete the message and continue printing.
For more information, please visit http://support.lexmark.com or contact customer support.
Try one or more of the following solutions:
Solution 149
![Page 150 of the Lexmark MS415 user manual — Change [paper source] to [paper format] places [print mode]](/cdn/reader/11/11c90aaaab7020db2ca4325302eeffdfad3e10338dfcaae2d5335733926fabfc/images/page-150.webp?w=400)
1 Turn off the printer.
2 Pull the plug off the power cord from the socket.
3 Remove the extra drawers.
4 Put the power cord plug back in the socket.
5 Turn the printer back on.
Try one or more of the solutions:
Try one or more of the solutions:
Try one or more of the solutions:
Troubleshooting 150
![Page 151 of the Lexmark MS415 user manual — Incorrect paper format. Open [paper source] [34]](/cdn/reader/11/11c90aaaab7020db2ca4325302eeffdfad3e10338dfcaae2d5335733926fabfc/images/page-151.webp?w=400)
Try one or more of the solutions:
Try one or more of the following solutions:
Press the control panel to erase the message and continue printing.
Try one or more of the following solutions:
Try one or more of the solutions:
Solution of problems 151
![Page 152 of the Lexmark MS415 user manual — Insufficient memory, some tasks are currently removed [35]](/cdn/reader/11/11c90aaaab7020db2ca4325302eeffdfad3e10338dfcaae2d5335733926fabfc/images/page-152.webp?w=400)
Try one or more of the following solutions:
Try one or more of the following solutions:
Try one or more of the following solutions:
> Institutions > > Institutions > > Print Settings > > Extra Menu > > Flash
format > > Yes > • Install additional printer memory.
Press the printer's control panel to delete the message.
Solving problems 152
![Page 153 of the Lexmark MS415 user manual — Serial option [x] error [54]](/cdn/reader/11/11c90aaaab7020db2ca4325302eeffdfad3e10338dfcaae2d5335733926fabfc/images/page-153.webp?w=400)
Perform any of the following actions:
Try one or more of the solutions:
Try one or more of the following solutions:
Browse the printer's control panel to:
> Institutions > > Institutions > > Print Settings > > Extra Menu > > Flash
format > > Yes > • Use a flash memory card with a larger capacity.
The printer had to be restarted. The last task may not be completed.
Select Continue on the printer's control panel to close the message and continue printing.
For more information, please visit http://support.lexmark.com or contact customer service.
Remove the paper stack from the standard drawer.
Try one or more of the solutions:
Solving problems 153
![Page 154 of the Lexmark MS415 user manual — Too many flash options installed [58]](/cdn/reader/11/11c90aaaab7020db2ca4325302eeffdfad3e10338dfcaae2d5335733926fabfc/images/page-154.webp?w=400)
SMTP server is not set. Consult the system administrator.
Press the printer's control panel to delete the message.
Try one or more of the solutions:
Try one or more of the following solutions:
1 Turn off the printer.
2 Pull the plug off the power cord from the socket.
3 Remove the extra flash memory.
4 Plug the power cord into a well grounded outlet.
5 Turn the printer back on.
Troubleshooting 154
![Page 155 of the Lexmark MS415 user manual — Cartridge and image processing unit do not match [41.xy]](/cdn/reader/11/11c90aaaab7020db2ca4325302eeffdfad3e10338dfcaae2d5335733926fabfc/images/page-155.webp?w=400)
1 Turn off the printer.
2 Pull the plug off the power cord from the socket.
3 Remove the extra drawers.
4 Plug the power cord into a well grounded outlet.
5 Turn the printer back on.
Try one or more of the following solutions:
1 Turn off the printer.
2 Pull the plug off the power cord from the socket.
3 Remove the unsupported optional card from the printer controller card and replace it with a supported card.
4 Plug the power cord into a well grounded outlet.
5 Turn the printer back on.
Web link server not set. Consult the system administrator.
Press the printer's control panel to delete the message.
1 Check that the toner cartridge and image processing unit are both Lexmark-authorized MICR (Magnetic Ink Character Recognition) or non-MICR-supports.
2 Replace the toner cartridge or image processing unit so that both are MICR or non-MICR substitutes authorised by Lexmark.
Fixing problems 155
![Page 156 of the Lexmark MS415 user manual — Image processing unit is virtually empty. Estimated number of remaining pages is [x] [84.xy]](/cdn/reader/11/11c90aaaab7020db2ca4325302eeffdfad3e10338dfcaae2d5335733926fabfc/images/page-156.webp?w=400)
If necessary, press the printer's control panel to erase the message and continue printing.
You may need to order a toner cartridge. If necessary, press the printer's control panel to erase the message and continue printing.
You may need to replace a toner cartridge very soon. Please refer to the . . replace Supplies section in the User's Manual for more information.
If necessary, press the printer's control panel to erase the message and continue printing.
Close the front valve of the printer.
Reference invalid. Print job cancelled.
Enter the correct references or contact the system administrator.
If necessary, press the printer's control panel to erase the message and continue printing.
You may need to order an image processing unit. If necessary, press the printer's control panel to erase the message and continue printing.
You may need to replace the image processing unit very soon. Please refer to the . . replace Supplies section in the User's Manual for more information.
If necessary, press the printer's control panel to erase the message and continue printing.
Solution problems 156
![Page 157 of the Lexmark MS415 user manual — Place [paper size] [print position] in [paper source]](/cdn/reader/11/11c90aaaab7020db2ca4325302eeffdfad3e10338dfcaae2d5335733926fabfc/images/page-157.webp?w=400)
Place the indicated drawer in the printer.
Try one or more of the following solutions:
Try one or more of the following solutions:
Try one or more of the following solutions:
Solution of problems 157
![Page 158 of the Lexmark MS415 user manual — Place [paper size] [print mode] in multifunctional input](/cdn/reader/11/11c90aaaab7020db2ca4325302eeffdfad3e10338dfcaae2d5335733926fabfc/images/page-158.webp?w=400)
Try one or more of the following solutions:
Try one or more of the solutions:
Try one or more of the solutions:
Try one or more of the solutions:
Troubleshooting 158
![Page 159 of the Lexmark MS415 user manual — None [supplytype] of Lexmark, see User's Manual [33.xy]](/cdn/reader/11/11c90aaaab7020db2ca4325302eeffdfad3e10338dfcaae2d5335733926fabfc/images/page-159.webp?w=400)
Try one or more of the solutions:
Try one or more of the following solutions:
The printer has detected that a supply or part of a brand other than Lexmark is installed in the printer.
Your Lexmark printer works best with original Lex Mark supplies and parts. When you use supplies or parts of other manufacturers, this may have a negative impact on the performance, reliability or lifetime of the printer and image processing components of the device. See 'Using Official Lexmark parts and supplies' on page 138 for more information.
All life indicators are designed to function with the supplies and parts Lexmark. If you use supplies or parts from other manufacturers, this may lead to unpredictable results. The use of image processing components longer than the intended lifetime can damage your Lexmark printer or its parts.
If you want to accept these risks and continue using non-original supplies or
parts in your printer, keep them
and the button # Pressed simultaneously on the control panel for 15 seconds.
In printer models without touch screen, keep and
press the control panel simultaneously for 15 seconds to close the message and continue printing.
If you do not want to accept these risks, remove the supply or component of other manufacturers from your printer and replace it with an original supply or part of Lexmark.
Solution of problems 159
![Page 160 of the Lexmark MS415 user manual — Place missing or non-reacting cartridge back [31.xy]](/cdn/reader/11/11c90aaaab7020db2ca4325302eeffdfad3e10338dfcaae2d5335733926fabfc/images/page-160.webp?w=400)
Print count exceeded. Print job cancelled.
Contact the system support department.
Print count exceeded. Print job not completed.
Contact the system support department.
Try one or more of the solutions:
For more information about installing the toner cartridge, see the 'Replace supplies' section. • If the toner cartridge is installed, remove it and install the non-reactive toner cartridges again.
Troubleshooting 160

Try one or more of the solutions:
For more information on installing the image processing unit, see the "Replace supplies" section. • If the image processing unit is installed, remove it and install the non-responsive toner cartridge again.
Replace the toner cartridge to delete the message and continue printing. For more information, please refer to the instructions provided with the supply or replace the . .
Install a toner cartridge that matches the printer's region code. x is the value for the region of the printer. y is the value for the region of the cartridge. x and y may have the following values:
1 United States, Canada
2 European Economic Area (EEA), Switzerland
3 Southeast Asia, Australia, New Zealand
5 Africa, Middle East, rest of Europe
![Page 162 of the Lexmark MS415 user manual — Replace unsupported image processing unit [32.xy]](/cdn/reader/11/11c90aaaab7020db2ca4325302eeffdfad3e10338dfcaae2d5335733926fabfc/images/page-162.webp?w=400)
Replace the image processing unit to erase the message and continue printing. For more information, please refer to the instructions provided with the supply or replace the . .
The printer requires maintenance. For more information, please visit http://support.lexmark.com. Or contact your service representative and report the problem.
Replace the toner cartridge and install a supported copy to delete the message and continue printing. Please refer to the instructions in the supply for more information.
This error can also be caused by installing an official Lexmark cartridge, such as a high-efficiency cartridge that is not intended for this product.
The following error codes indicate that a non-original Lexmark toner cartridge is installed:
32.13 32.16 32.19 32.22 32.25 32.28 32.31 32.34 32.37
See 'Using Official Lexmark parts and supplies' on page 138 for more information.
Replace the image processing unit and install a supported copy to delete the message and continue printing. Please refer to the instructions in the supply for more information.
This error can also be caused by the installation of an original Lexmark image processing unit, such as a MICR unit, which is not intended for this product.
The following error codes indicate that a non-original Lexmark image processing unit is installed:
32.14 32.17
Solution 162

32.20 32.23 32.26 32.29 32.32 32.35 32.38
See 'Using Official Lexmark parts and supplies' on page 138 for more information.
Step 1 Check that the printer is on.
Go to step 2. Turn on the printer.
- Is the printer enabled?
Step 2 Check that the printer is in sleep or slumber mode.
Press the sleep button to disable sleep or slumber mode.
Go to step 3.
Is the printer in sleep or slumber mode?
Step 3. Check that one end of the power cord is connected to the printer and another end on a grounded socket.
Go to step 4. Connect one end of the power cord to the printer and another end to a grounded outlet.
Is the power cord connected to the printer and a grounded outlet?
Step 4. Check the other electrical equipment connected to the power outlet.
Disconnect the other electrical equipment and switch on the printer. If the printer does not work, reconnect the other electrical equipment.
Go to step 5.
Does the other electrical equipment work?
Solving problems 163 · Action Yes No

Go to step 6. Make sure the following items match:
Check that the cables with which the printer is connected are in correct ports.
Are the cables in the correct ports?
Step 6. Make sure the power outlet is not switched off using a switch or circuit breaker.
Turn on the switch or reset the circuit breaker.
Go to step 7.
Is the power outlet switched off using a switch or circuit breaker?
Connect the mains cord of the printer directly to a grounded outlet.
Go to step 8.
Check if the printer is connected to an overvoltage device, a UPS or extension cord.
Is the printer connected to an overvoltage protection, UPS or extension cord?
Step 8 Check that one end of the printer cable is connected to a port of the printers and another end on the computer, print server, option or other network device.
Go to step 9. Connect the printer cable firmly to the printer and on computer, print server, option or other networkap- ready.
Is the printer cable securely connected to the printer and computer, print server, option or other network device?
Go to step 10. Turn off the printer, remove all packaging material, reinstall hardware options and turn on the printer again.
Make sure all hardware options are properly installed and remove packaging material.
Are all hardware options well installed and has all packaging material been removed?
Go to step 11. Use the correct settings in the printer driver.
Check that you have selected the correct port settings in the printer driver.
Are the port settings correct?
Step 11 Check the installed printer driver.
Go to step 12. Install the correct printer steering program.
Is the correct printer driver installed?

The problem is solved.
Contact Customer supportif you want to scan any more pages.
Disable the printer and turn on the printer after about 10 seconds.
Step 1 Press the sleep button on the printer's control panel.
The problem is solved.
Go to step 2.
Appears Done On the printer display?
Step 2 Disable the printer and turn on the printer after about ten seconds.
The problem is solved.
Turn off the printer and contact Customer supportif you want to scan any more pages.
Appear Please wait and Done On the printer display?
The problem is solved.
Go to step 2.
Disable the printer and turn on the printer after about ten seconds.
Does the internal option work correctly?
Step 2 Check for internal option is correctly installed in the control-ler card.
Go to step 3. Connect the internal option to the controller card.
a Turn off the printer with the on-off switch and pull the plug
Out of the socket. b Check if the internal option is installed in the correct one
connector on the controller card. c Connect the power cord to the printer, plug it into a grounded
power supply and switch on the current.
Is the internal option correctly installed in the controller card?
Go to step 4. Reinstall the internal option.
Print a page with menu settings to check if the internal option is listed in the list of installed functions.
Is the internal option mentioned on the menu settings page?

The problem is solved.
Contact Customer support.
a Check if the internal option is selected.
You may need to add the option manually in the printer's tool to make it available for printing tasks. See 'Add available options of the printer driver' on page 20 for more information. b Send the print job again.
Does the internal option work correctly?
The problem is solved.
Go to step 2.
a Open the drawer and enter one or more of the following operations
from:
The problem is solved.
Go to step 3.
a Disable printer and turn off printer after about ten
seconds back in. b Send the print job again.
Go to step 4. Put the paper tray back. For more information, please refer to the included drawer installation documentation.
Check that the drawer is installed and recognized by the printer.
Print a page with menu settings and check that the tray is listed in the list of installed functions.
Is the drawer on the menu settings page?

Go to step 5. Add the drawer manually to the printer's control program.
Check that the drawer is available in the printer driver.
Is the drawer available in the printer driver?
The problem is solved.
Contact Customer supportif you want to scan any more pages.
Check that the option is selected.
a Select the option in the application you are using. Mac OS 9-
users: make sure the printer is set in the Chooser. b Send the print job again.
Open the front valve and remove all drawers.
Contact Customer support.
The problem is solved.
a Remove blocked page .
b Press to erase the message and continue printing.
Is the message about stuck paper still displayed?
a Turn on the post-disruption recovery function.
The problem is solved.
Contact Customer support.
1 Browse the printer's control panel to:
> Institutions > > General Settings > >
Reset print > > Recovery after failure > 2 Press the arrow keys until To or Automatic is again-
give and press. b Send the unprinted pages again.
Are the pages that have been blocked printed again?

Go to step 2. The problem is solved.
a Pull the drawer out and perform one of the following steps:
If repair is enabled after failure, the print jobs will be automatically reprinted.
Are paper failures still on the record?
Go to step 3. The problem is solved.
a Replace the paper. Use paper from a new suit.
Are paper failures still on the record?
Contact Customer supportif you want to scan any more pages.
The problem is solved.
a Read the tips on avoiding malfunctions. See 'Prevention of
paper failures' on page 128 for more information. b Follow the recommendations and send the print job
Again.
Are paper failures still on the record?
a Browse the printer's control panel to:
Contact Customer supportif you want to scan any more pages.
The problem is solved.
Next > > Fix the malfunction, press OK > b Follow the instructions on the display.
Isn't the message about the paper that got stuck disappearing?

a Turn on recovery after failure.
The problem is solved.
Contact Customer support.
1 Browse the control panel to:
Institutions > General Settings >Reset print > Recovery after malfunction 2 Select To or Automatic.
3 Press , depending on your printer model. b Send the pages that were not printed again.
Were the pages that were blocked printed?
The problem is solved.
Go to step 2.
a Open the print dialog from the document that
you want to print and check that you have selected the correct printer.
Are the tasks printed?
The problem is solved.
Go to step 3.
a Check that the printer plug is in the socket properly,
whether the printer is enabled, or Done is displayed on the printer display. b Send the print job again.
Are the tasks printed?
The problem is solved.
Go to step 4.
If an error message appears on the printer display, you will delete the message.
Are the tasks printed?

The problem is solved.
Go to step 5.
a Check that the ports (USB, serial or Ethernet) are working and whether
the cables are firmly connected to the computer and printer.
Are the tasks printed?
The problem is solved.
Go to step 6.
a Disable printer and turn off printer after about ten
seconds back in. b Send the print job again.
Are the tasks printed?
The problem is solved.
Contact Customer support.
a Remove the printer software and reinstall it. See 'The
install printer software' on page 19 for more information.
Are the tasks printed?
Place A4 or Letter paper in the drawer and re-send the printing task. Has the print speed been increased?
The problem is solved.
Contact customer support.

The problem is solved.
Go to step 2.
a Check if you print on paper supported by the
Tray. b Send the print job again.
Is the task printed from the right drawer or on the correct paper?
The problem is solved.
Go to step 3.
a Set the printer's control panel in the Paper menu
paper size and type settings in such a way that they correspond to the paper placed in the drawer. b Send the print job again.
Is the task printed from the right drawer or on the correct paper?
The problem is solved.
Go to step 4.
a Depending on your operating system, open the dialog
Print or Print Preferences and specify the type of paper. b Send the print job again.
Is the task printed from the right drawer or on the correct paper?
The problem is solved.
Contact Customer supportif you want to scan any more pages.
a Check that the drawers are not connected. b Send the print job again.
Is the task printed from the right drawer or on the correct paper?
Deactivate Hex Trace mode.
Go to step 2.
Make sure the printer is not in Hex Trace mode.
Is the printer in Hex Trace mode?
Contact Customer supportif you want to scan any more pages.
The problem is solved.
a Select the option on the printer's control panel
Standard network or Network [x] And turn on SmartSwitch. b Send the print job again.
Are there wrong characters printed?

a In the Paper menu, enter on the printer's control panel
The problem is solved.
Contact Customer support.
the size and type of paper in the drawers to be coupled.
Are the drawers correctly paired?
The problem is solved.
Go to step 2.
a Set the printer's control panel in the Finish menu
the Sort option by (1,2,3) (1,2,3). b Send the print job again.
Is the task correctly printed and sorted?
The problem is solved.
Go to step 3.
a In the printer software, set the Sort option to (1,2,3) (1,2,3).
Is the task correctly printed and sorted?
Step 3. Make the task less complex by reducing the number of different letter types and font sizes, limiting the number and use easier images or having fewer pages printed at once.
The problem is solved.
Contact Customer supportif you want to scan any more pages.
Is the task correctly printed and sorted?

The problem is solved.
Go to step 2.
Adjust the print timeouts.
a Browse the printer's control panel to:
Institutions > Print Settings > Time-outs > Print Select a higher value and then select depending on the
printer or Send. c Send the print job again.
Is the file printed correctly?
The problem is solved.
Contact Customer supportif you want to scan any more pages.
a Check if there are manual page endings in the original file. b Send the print job again.
Is the file printed correctly?
Step 1 Reduce the number of different fonts and font sizes, use fewer and simpler images and limit the number and print job pages.
Go to step 2. The problem is solved.
Is printing the job still long?
Go to step 3. The problem is solved.
Disable the Page Protection feature.
Browse the printer's control panel to:
> Institutions > > General Settings > >
Reset print > > Page Security > > Off >
Is printing the job still long?

Install additional printer memory.
The problem is solved.
Browse the printer's control panel to:
For more information, please contact Customer support.
> Institutions > > General Settings > >
Eco‑mode > select an institution >
Is printing the job still long?
The problem is solved.
Go to step 2.
a Check that the print options for PDF output are such
set to include all fonts. b Generate a new PDF file and send the print job
Again.
Are the files printed?
The problem is solved.
Contact Customer supportif you want to scan any more pages.
a Open the document you want to print in Adobe Acrobat. b Click on Stock > Print > Advanced > Print As
image > OK > OK.
Are the files printed?

Step 1 Open the waiting task folder on display and check that your print job is displayed.
Go to step 2. Select one of the options for Print and Wait tasks and send the print job again. See 'Save printing tasks on the printer' on page 59 for more information.
Is your job displayed in the folder with interrupted tasks?
The problem is solved.
Go to step 3.
The print job may contain a formatting error or invalid data.
Save each print job with a different name and then send the individual tasks to the printer.
Is the task printed?
The problem is solved.
Add extra printing memories.
Free up extra printer memory by removing some of the interrupted tasks.
Is the task printed?
The problem is solved.
Go to step 2.
Change the settings for the printer's energy use.
a Browse the control panel to:
Institutions > General Settings b Select Eco Mode or Silent Mode and select Off.
Is the document printed?


Lower the font size, number of images and their complexity, and the number of pages of the print job, and send the task again.
a Remove tasks held in printer memory. b Send the print job again.
Browse the control panel to: Institutions > General Settings > Reset print > Page Security >From b Send the print job again.

a Move the width and length guides in the drawer to the right
position for the paper placed in the printer. b Send the print job again.
Troubleshooting 176

Go to step 3. Perform one or more of the following operations:
Specify the type and size of paper in the tray from the Paper menu on the printer control panel.
Do the paper size and type of paper match the paper in the drawer?
Go to step 4. The problem is solved.
a Specify the paper format via Preference Settings for
print or the printing dialog, depending on the pollination system. b Send the print job again.
Is the page or image not fully printed?
Contact Customer support.
The problem is solved.
a Replace the image processing unit in the printer.
1 Remove the toner cartridge. 2 Remove the image processing unit.
Is the page or image not fully printed?
ABCD


Step 1 Place paper of the correct size and weight in the drawer.
Go to step 2. Place paper of the correct size and weight in the drawer.
Does the loader contain paper of the correct size and weight?
Step 2 Specify the paper type and weight settings in the tray from the Paper menu on the printer's control panel.
Go to step 3. Make sure the paper in the drawer matches the type and weight settings specified by the tray settings.
Is the drawer set to the type and weight of the paper in the drawers?
Go to step 4. The problem is solved.
a Specify the paper type and weight settings in Preferences-
Print settings or print dialog, depending on your operating system. b Send the print job again.
Are prints still containing shadow images?
Contact Customer support.
The problem is solved.
Replace the image processing unit and re-send the print job.
Are prints still containing shadow images?

a Specify a lower value for toner intensity in the menu

The problem is solved.
Go to step 3.
Replace the image processing unit and then the toner cart tridge.
a Remove the toner cartridge. b Remove the image processing unit.
cartridge. d Send the print job again.
Have the grey backgrounds disappeared?
The problem is solved.
Contact Customer support.
Replace the image processing unit and re-send the print job.
Have the grey backgrounds disappeared?
ABCD ABCD ABCD
The problem is solved.
Go to step 2.
a Move the width and length guides into the right position for
paper placed in the printer. b Send the print job again.
Are the margins correct?

Go to step 3. Perform one or more of the following operations:
Specify the size of the paper in the drawer from the Paper menu on the printer's control panel.
Does the paper size match the paper in the drawer?
The problem is solved.
Contact Customer support.
a Specify the paper format via Preference Settings for
print or the printing dialog, depending on the pollination system. b Send the print job again.
Are the margins correct?
Go to step 2. Adjust the width and length guides.
Set the width and length guides in the drawer to the correct position for the size of the paper placed in the printer.
Are the width and length guides in the correct position?
Go to step 3. In the case of drawer settings, specify the type and weight of paper placed in the tray.
Specify the paper type and weight settings in the tray from the Paper menu on the printer's control panel.
Do paper and weight match the paper in the drawer?
Go to step 4. The problem is solved.
a Specify the paper type and weight settings in Preferences-
Print settings or print dialog, depending on your operating system. b Send the print job again.
Is the paper still curled?


a Remove the stack of paper from the drawer and turn the pile. b Send the print job again.
) ) ABCDE
ABCDE ABCDE
Go to step 2. The problem is solved.
a Adjust the width and length guides in the drawer to correct position
for the size of the paper placed in the drawer. b Send the print job again.
Are prints still containing irregularities?
Step 2 Specify the type and size of paper in the tray from the Paper menu on the printer control panel.
Go to step 3. In the case of drawer settings, specify the type and size of paper placed in the tray.
Do the printer settings for paper type and weight correspond to the paper in the drawer?
Go to step 4. The problem is solved.
a Specify the paper type and weight settings in Preferences-
Print settings or print dialog, depending on your operating system. b Send the print job again.
Are prints still containing irregularities?

Specify the paper structure in the drawer from the Paper menu on the printer's control panel.
Go to step 5.
Check that the paper in the drawer has a structure or rough finish.
Prints on paper with structure or rough finish?
Go to step 6. The problem is solved.
a Load paper out of a new suit.
Are prints still containing irregularities?
Step 6. Replace the image processing unit and re-send the print job.
Contact Customer support on http://support.lexma rk.com or your service representative.
The problem is solved.
Are prints still containing irregularities?
Go to step 2. 1 Check that the distance between failures is 80 mm (3.15 inches) 2 Note the distance and contact Customer support on http://support.lexmark.com or your service representative.
Measure the distance between malfunctions.
Check that the distance between failures is equal to:
Is the distance between the failures equal to one of the dimensions mentioned?

Contact Customer support on http://support.lex mark.com or your servi- ce representative.
The problem is solved.
Replace the image processing unit and re-send the print job.
Are prints still contained in repeated malfunctions?
Go to step 2. The problem is solved.
a Specify lower value for toner intensity in the menu
Quality on the printer's control panel.
Is the print still too dark?
Go to step 3. Perform one or more of the following operations:
a Enter the paper type, structure and weight settings of
the paper in the drawer on the printer's control panel, in the Paper menu. b Send the print job again.
Is the drawer set to the type, structure and weight of the paper in the drawers?

Go to step 4. The problem is solved.
a Specify the paper type, structure and weight settings
Print or print dialog preference settings depending on your operating system. b Send the print job again.
Is the print still too dark?
Step 4. Check that the paper in the drawer has a structure or rough finish.
In the Paper menu on the printer's deck panel, specify the structure settings that match the paper you print.
Go to step 5.
Prints on paper with structure or rough finish?
Go to step 6. The problem is solved.
a Load paper out of a new suit.
Is the print still too dark?
Contact Customer support.
The problem is solved.
Replace the image processing unit and re-send the print job.
Is the print still too dark?
Go to step 2. The problem is solved.
a Specify a higher value for toner intensity in the menu
Quality on the printer's control panel.
Is the print still too light?

Go to step 3. Set the type of paper, paper structure and weight to the paper placed in the drawer.
Specify the paper type, structure and weight settings in the tray from the Paper menu on the printer's control panel.
Is the drawer set to the type, structure and weight of the paper in the drawers?
Go to step 4. The problem is solved.
a Specify the paper type, structure and weight settings
Print or print dialog preference settings depending on your operating system. b Send the print job again.
Is the print still too light?
In the Paper menu on the printer's deck panel, specify the structure settings that match the paper you print.
Go to step 5.
Make sure the paper has no structure or rough finish.
Prints on paper with structure or rough finish?
Go to step 6. The problem is solved.
a Load paper out of a new suit.
Is the print still too light?
Go to step 7. The problem is solved.
a Distribute the toner evenly across the image processing unit.
1 Remove the toner cartridge and then remove the image unit. 2 Shake the image processing unit well back and forth.
Is the print still too light?

Contact Customer support.
The problem is solved.
Replace the image processing unit and re-send the print job.
Is the print still too light?
Go to step 2. The problem is solved.
a Check that all packaging material has been removed from the image-
processing unit.
1 Remove the toner cartridge and then remove the image unit. 2 Check that the packaging material has been correctly removed from the image processing unit.
Is the printer still printing empty pages?
Go to step 3. The problem is solved.
a Distribute the toner evenly across the image processing unit.
1 Remove the toner cartridge and then remove the image unit. 2 Shake the image processing unit well back and forth.
Is the printer still printing empty pages?

Contact Customer support.
The problem is solved.
Replace the image processing unit and re-send the print job.
Is the printer still printing empty pages?
) ) ABCDE
ABCDE ABCDE
Go to step 2. The problem is solved.
a Adjust the width and length guides in the drawer to correct position
for the size of the paper placed in the printer. b Send the print job again.
His prints still crooked?
Contact Customer support.
The problem is solved.
a Check if you print on paper supported by the
Tray. b Send the print job again.
His prints still crooked?

Go to step 2. The problem is solved.
a Replace the image processing unit in the printer.
1 Remove the toner cartridge and then remove the image unit.
Is the printer printing plain black pages?
Step 2 Replace the image processing unit and re-send the print job.
Contact Customer support.
The problem is solved.
Is the printer printing plain black pages?
Go to step 2. Set the type of paper to Transparent.
Specify the type of paper in the drawer from the Paper menu on the printer control panel.
Is the type of paper for the drawer set to Transparent?
Contact Customer support.
The problem is solved.
a Check that you are using a recommended type for transparency. b Send the print job again.
Is the print quality still bad?
ABCDE ABBCTE AB CDE

Go to step 2. The problem is solved.
a Enter the tray or input in Print Preferences Settings
or the print dialog, depending on the operating system. b Send the print job again.
Do printing contain horizontal stripes?
Go to step 3. Set the type of paper and weight to the paper placed in the drawer.
Specify the paper type and weight settings in the tray from the Paper menu on the printer's control panel.
Do paper and weight match the paper in the drawer?
Go to step 4. The problem is solved.
a Load paper out of a new suit.
Do printing contain horizontal stripes?
Go to step 5. The problem is solved.
a Replace the image processing unit in the printer.
1 Remove the toner cartridge and then remove the image unit.
Do printing contain horizontal stripes?
Step 5. Replace the image processing unit and re-send the print job.
Contact Customer support.
The problem is solved.
Do printing contain horizontal stripes?

ABCDE ABBCTE AB CDE
Go to step 2. The problem is solved.
a Specify the paper type, structure and weight settings
Print or print dialog preference settings depending on your operating system. b Send the print job again.
Do printing contain vertical stripes?
Go to step 3. Perform one or more of the following operations:
Specify the paper structure, type and weight settings in the tray from the Paper menu on the printer's control panel.
Do paper structure, type and weight correspond to the paper in the drawer?
Go to step 4. The problem is solved.
a Load paper out of a new suit.
Do printing contain vertical stripes?


Contact Customer support on http://support.lexma rk.com or your service representative.

a Check that your software uses the correct filling pattern. b Send the print job again.
a Place a recommended paper size in the specified tray or
Troubleshooting 191


1 Remove the toner cartridge and then remove the image unit. 2 Shake the image processing unit well back and forth.
Step 4. Replace the image processing unit and re-send the print job.

a Check that your software uses the correct filling pattern. b Send the print job again.
a Specify the paper type and weight settings
in the drawer on the printer's control panel, in the Paper menu. b Send the print job again.
Solution of Problems 192

Go to step 4. The problem is solved.
Check that you are using a recommended paper type.
a Place a recommended paper size in the indicated tray or
import. b Send the print job again.
Do printing contain vertical interruptions?
Contact Customer support.
The problem is solved.
a Distribute the toner evenly across the image processing unit.
1 Remove the toner cartridge and then remove the image unit. 2 Shake the image processing unit well back and forth.
Do printing contain vertical interruptions?
Replace the image processing unit and re-send the print job.
Contact Customer support.
The problem is solved.
Did the prints contain toner spots?
ABCDE
ABCDE ABCDE


Step 1 Replace the image processing unit in the printer.
Contact Customer support on http://support.lexma rk.com or your service representative.

Step 1 Check the paper type, texture and weight in the Paper menu on the printer's control panel.
Go to step 2. In the case of drawer settings, specify the type, structure and weight of paper placed in the tray.
Do the settings for paper type, texture and weight correspond to the paper in the drawer?
Troubleshooting 194

Replace the image processing unit and re-send the print job.
Contact Customer support.
The problem is solved.
Is the printing density uneven?
Signs have fragrant or uneven edges.
Go to step 2. The problem is solved.
a The list of font examples to check the
used fonts are supported by the printer.
1 Browse the printer's control panel to:
> Reports > > Print fonts > 2 Press the arrow keys until PCL fonts or PostScript Fonts is displayed and press
. b Use a font supported by the printer or
install the font you want to use. Please contact your system administrator for more information. c Send the print job again.
Do printing still contain characters with serrated or odd edges?
Contact Customer support.
The problem is solved.
a Use a font supported by the printer or
install the font you want to use. Please contact your system administrator for more information. b Send the print job again.
Do printing still contain characters with serrated or odd edges?

Signs have fragrant or uneven edges.
Go to step 2. Select a font supported by the printer.
a The list of font examples to check the
used fonts are supported by the printer.
1 Browse the control panel to: Menus > Reports > Print fonts 2 Select PCL fonts or PostScript Fonts. b Send the print job again.
Do you use fonts supported by the printer?
The problem is solved.
Contact Customer support.
Check that the installed fonts on your computer are supported by the printer.
Are the installed fonts on your computer supported by the printer?
The problem is solved.
Go to step 2.
a Turn on the printer. b Open a web browser and type the printer's IP address.
c Press Enter.
Does the Embedded Web Server open?

The problem is solved.
Go to step 3.
Check that the printer's IP address is correct.
a Display the printer's IP address:
Does the Embedded Web Server open?
The problem is solved.
Go to step 4.
Check that the network is working.
a Print a page with network settings. b Check the first part of the page with network setup-
The printer must be connected to the status.
Note: If status indicates that the printer is not connected, there may be a fault of connection or the network cable is not functioning properly. Contact the system administrator to resolve this problem and then print another page of network settings. c Open a web browser and type the printer's IP address. d Press Enter.
Does the Embedded Web Server open?
Step 4. Check that the cable connections to the printer and print server are securely attached.
The problem is solved.
Go to step 5.
a Connect the cables properly. Please refer to the supplied
printer installation documentation for more information. b Open a web browser and type the printer's IP address.
c Press Enter.
Does the Embedded Web Server open?
Step 5. Disable the web proxy servers temporarily.
The problem is solved.
Contact the system support department.
Proxy servers can ensure that you have no or limited access to certain websites including the Embedded Web Server.
Does the Embedded Web Server open?

Before contacting customer support, make sure you have the following information:
Go http://support.lexmark.com for support by email or via chat, or browse through the library of manuals, supporting documentation, drivers and other downloads.
Technical support via the phone is also available. In the US or Canada, call 1-800-539-6275. Go to other countries or regions http://support.lexmark.com.
Solving problems 198

Product name:
Lexmark MS312dn, MS315dn., MS317dn; MS415dn and MS417dn
Device type:
Models:
The following paragraph shall not apply to countries where the conditions are contrary to national law: LEXMARK INTERNATIONAL, INC., THIS PUBLICATION AS SUCH PROVIDES WITHOUT ANY FORM OF GUARANTEE, NEITHER IMPLIED NOR EXPLICIT, INCLUDING BUT NOT LIMITED TO THE IMPLICIT GUARANTEES OF MERCHANTABILITY OR SUITABILITY FOR A PARTICULAR PURPOSE. In some jurisdictions, rejection of explicit or implied guarantees is not permitted in certain transactions, so this statement may not apply to you.
This publication may contain technical inaccuracies or typographical errors. The information contained in this publication is regularly reviewed, changes will be included in subsequent expenditure. The products or programmes described may be improved or modified at any time.
References in this publication to products, programmes or services do not imply that the manufacturer intends to place these products on the market in all countries where the manufacturer is active. A reference to a product, program or service does not mean that only that product, that program or that service can be used. Instead, all functionally equivalent products, programmes or services, which do not infringe existing intellectual property rights, may be used. The user shall be responsible for the evaluation and control of operation in conjunction with other products, programmes or services, except those products, programs or services specified by the manufacturer.
Go http://support.lexmark.com for technical support of Lexmark.
Go www.lexmark.com for information on supplies and downloads.
© 2012 Lexmark International, Inc.
All rights reserved.
Lexmark, the Lex mark logo, MarkNet and MarkVision are trademarks or registered trademarks of Lex Mark International, Inc., filed in the United States and/or other countries.
Google Cloud Print is a trademark of Googel Inc.
Notifications 199 · 330, 335, 530 · November 2017

Mac and the Mac logo are trademarks of Apple Inc., filed in the United States and other countries.
Microsoft and Windows are registered trademarks or trademarks of the Microsoft business group in the United States and other countries.
Mopria®, the Mopria® logo and the Mopri® Alliance logo are registered trademarks and service marks of Mopria Alliance, Inc. in the United States and other countries. Unauthorized use is strictly prohibited.
PCL is a registered trademark of Hewlett-Packard Company. PCL is an indication of Hewlett- Packard Company for a collection of printer assignments (printer language) and functions in its products. This printer is designed to support the PCL language. The printer recognizes PCL commands used in various applications and emulates the functions corresponding to these commands.
PostScript is a registered trademark of Adobe Systems Incorporated in the United States and other countries.
The following terms are trademarks or registered trademarks of these companies:

CG Times Based on Times New Roman licensed by The Monotype Corporation plc, it is a product of the Agfa Corporation
Notifications 200

Times New Roman The Monotype Corporation plc
Univers Linotype-Hell AG and/or subsidiaries
Other trademarks are the property of their respective holders.
AirPrint and the logo of AirPrint are trademarks of Apple, Inc.
All license notifications associated with this product can be found in the main directory of the documentation CD.
The following measurements are made in accordance with ISO 7779 and reported according to ISO 9296.
Noise pressure on average 1 m, dBA
Values can be changed. Go www.lexmark.com for current values.
The WEEE logo indicates that there are specific recycling programmes and procedures for electronic products in the countries of the European Union. We ask you to recycle our products.
If you have further questions about recycling options, please visit Lexmark's website at www.lexmark.com for the phone number of your local supplier.
Do not throw away the printer or components with household waste. Contact your municipality for disposal and recycling options.
Notifications 201 · Completed 15

This symbol indicates components sensitive to static electricity discharge. Touch parts in the areas listed below only after you first touch a metal surface outside of the area with the symbol.
All Lexmark products with the ENERGY STAR logo on the product or on a home screen are certified in accordance with EPA's ENERGY STAR requirements, if the configuration set by Lex Mark still applies.
Ambient temperature 16 to 32 °C
Temperature for transport -40 to 43.3°C
Temperature for storage and relative humidity 2 to 35°C
8 to 80% relative humidity
The printer is certified in the United States as a product that meets the requirements of DHHS 21 CFR Chapter 1, Subpart J for Class I (1) laser products. Elsewhere, the printer is certified as a class I laser product that meets the requirements of IEC 60825-1: 2014.
Class I laser products shall be considered as not presenting any danger. The printer contains an internal class IIIb (3b) laser, a gallium arsenide laser with a rated power of 12 milliwatts and a wavelength range of 655-675 nanometres. The laser system and printer are designed to ensure that users never experience laser radiation higher than the permitted level for Class I devices, during normal use, maintenance work by the user or prescribed service activities.
The label containing safety information may be affixed to the printer as follows:
Notifications 202

NEBEZPEČÍ - Když jsou vyjmuty kazety a je odblokována pojistka, zkla ze z. je vysíláno neviditelné laserové záření. Nevystavujte se působení laserového paprsku. FARE - Usynlig laserstråling, når patroner fjernes, og spærreanordningen er slået fra. Undgå at blive udsat for laserstrålen.
VAARA - Näkymätöntä lasersäteilyä on varottava, kun värikasetit on postettu ja lukitus on auki. Vältä lasersäteelle altistumista.
VESZÉLY . . Nem látható lézersugárzás fordulhat elő a patronok eltávolításakor és a zárószerkezet felbontásalkor. Kerülje a lezersugárnak való kitettséget. PERIOLO - Emissione di radiazioni laser invisibili durante la rimozione delle cartucce e del blocco. Evitare l . . esposizione al raggio laser.
FARE . . Usynlig laserstråling når cassette bag ut og sperren er satt ut av spill. Unngå eksponering for laserstrålen. NIEBEZPIECZE'SSTWO - niewidzialne promienianonie laserowe podczas usuwania kaset i blockady. Należy unikać naświetlenia promieneem lasera.
ОПАСНО! Невидимое лазерное излучение при извнеченных картриджах и снятии блокировки. Избегайне воздействия лазерных лучей. Pozor . . Nebezpečenstvo neviditeľného laserového žiarenia pri odobratých kazetách a odblokovanej poistke. Nevystavujte sa lúčom.
FARA . . Osynlig laserstrålning när patroner tas ur och spärrmekanismen är upphävd. Undvik exponering för laserstrålen. . . - .
. . - .
The following table describes the printer's energy consumption characteristics.
Mode Description Power consumption (Watt)
Printing
Paper copies of electronic imports shall be made with the product.
Copying Paper copies of paper originals are made with the product.
Scan Paper originals are scanned with the product. N/A
Ready The product is waiting for a printing job. 7
Sleep Mode The normal device save mode is activated. 3
Snooze mode The optimal saving mode of the device is activated. 0.5
The product is connected to an outlet, but the device is switched off.
The energy consumption levels shown in the previous table indicate measurements of average times. Immediate energy reductions can be substantially higher than the average.
Values can be changed. Go www.lexmark.com for current values.
Notifications 203 · 0.0

This product has an energy-saving mode called sleep mode. In sleep mode, energy is saved by reducing power consumption during longer periods of time when the device is not active. The sleep mode is automatically switched on when the product is not used for a pre-set period (timeout for sleep mode).
Default setting for the time-out of this product (in minutes): 20
You can set the time-out for sleep mode from configuration menus between 1 minute and 120 minutes. If you set the sleep timeout to a low value, energy consumption will decrease but product response times may increase. When you set the time-out for sleep mode to a high value, the printer reacts quickly but more energy is consumed.
This product has a mode in which it consumes very little energy called slumber mode. If the printer's slumber mode is active, other systems and devices will be switched off safely.
You can use the following methods to enable slumber mode:
The standard slumber mode time-out for this product in all countries or regions 3 days
You can set the time period that the printer waits for before the slumber mode is enabled after a task has been printed between one hour and one month.
If this product has a state in which it is switched off but still consumes a small amount of energy and you want to stop the power consumption completely, pull the plug on the product from the socket.
It is sometimes useful to calculate the total energy consumption of the product. As the power consumption is indicated in watts, the current consumption should be multiplied by the time that each mode is active on the product. This way you can calculate the energy consumption. The total energy consumption of the product is the sum of the energy consumption for all modes.
This product complies with the safety requirements of Council Directives 2014/30/EU, 2014/35/EU, 2009/125/EC and 2011/65/EU on harmonisation of Member States' laws relating to electromagnetic compatibility and safety of electrical equipment designed for use within certain voltage limits, energy efficiency of products that energy
Notifications 204

use and restriction of the use of certain hazardous substances in electrical and electronic equipment.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550, United States. The recognised representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY. A declaration of conformity to the requirements of the regulations may be obtained on request from the approved representative or www.lexmark.com/en us/about/regulatory-compliance/european-union-declaration-of-conformity.html.
This product meets the requirements of EN55022 and EN55032 with regard to Class B products and safety requirements of either EN 60950-1 or EN 62368-1.
Notifications 205

Sleep button, light of 31 image processing unit
Configuration modified, some tasks on hold have not been restored [57] 151 configuration data
display, printer control panel
order 140 replace 142 Image processing unit almost empty [84.xy] 156 Image processing units almost empty, expected to print [x] pages [84
adjust, fix brightness 73 display problems
Wireless network 21 configurations
printer display is empty print 165 documents
printer 11 Configuration MP (U-loader configuration), configure menu 85
from a computer 57 from a mobile device 59 wireless network
configuration data 21 Wireless, menu 93, 95 wireless network installation
View Embedded Web Server 64
multiple printers 64 supply, notifications about
reports 66 available, internal options 14 ordering
Image processing unit 64 supply, reports about
with the Embedded Web
Server 25 Push button, configuration method
toner cartridge 64 configure, custom paper types 44 configures, Universal paper format settings 34 configure and supplies 64 conservation settings
Image processing unit 140 ordering, supplies
toner cartridges 139 Secure printing, menu 103 secure print jobs
Clear 76 Embedded Web Server
change print settings 69 security
adjust, brightness 73 admin settings 64 confidential settings
Eco Mode 67, 70 Adjust brightness 73 Planning current 69, 72 Sleeping position 73 Sleep mode 68, 71 Lull time-out 68,71 Silent mode 71 Contact customer support 198 Checking, Print tasks 59 Checking the status of parts and supplies 137, Virtual display
printing jobs change 69 security, locking 75 security, web page for
resize 69 jobs, set to
other printers 64 network settings 64 problem with access 196 access 32 access to external
link 44, 45 drawers 35 unplug 44, 45 letterhead
Control Panel 65 Embedded Web Server, Security: Administrator Manual
with the Embedded Web
where you can find it 64, 77 emissions notifications 201 envelopes
C Cartridge almost empty [88.xy] 156 Cartridge almost blank, expected to print [x] pages [88,xy ] 156 Cartridge and image processing unit do not match [41.xY] 155 Complex page printing may fail [35] 147 Complex page, certain data may not be printed [36] 151
D Set date and time, open the Embedded Web Server menu 104 32 The printer had to be restarted. The last task may not be completed. 153 Defect. flash memory [51] 147 directory list
preparation of a 20 Ethernet network
preparation of printing via
Ethernet 20 Etherenetport 18 labels, paper



in standard export drawer 133 in drawers 135 paper labels
Place [string for custom paper] [print position] in [paper source] 157 Place input tray [x] 157 place missing or non-reactive image processing unit back [31.xy] 161 Place missing or unresponsive cartridge back [ 31.xY] 160 place for printer determine 11 places, in optional drawer 35 Planning current mode
may fail
data may not be printed
some tasks on hold have not been restored [57] 151 The printer had to be re-established
supported by printer 54 paper input, troubleshooting
are being started. The last task may not be completed. 153 Defect. flash memory [51] 147 Flash corrupted
message remains after malfunction
has been corrected 167, 168 paper type
setting 33 type of paper, adjusted
use 69, 72 PostScript, menu 116 printer
[53] 155 Flashgeh. Not formatted.
configure 44 assign 45, 47 types of paper
base model 11 location select 11 minimum installation space 11 move 11, 144 transport 145 printer prints empty pages 186 Printer restart. Check last task. 149 printer cleaning 137 printer transporting 145 printer preparing for connection to a wireless network 20 printer, simple troubleshooting 163 printer messages
[53] 148 Flash Memory Full of thelooped and re-enabled [52] 148 None [supply type] of Lexmark,
suitable for which tray (s) 55 supported by printer 55 support for duplex 55 paper stop, use 34 paper failures
See User's Manual [33.xy] 159 Memory full [37] 159 May flashgeh. Not defrag.
prevent 128 parallel port 18 Parallel port disabled [56] 160 PCL Emul, menu 118, 122 PDF, guy 122 PIN, method
[76] May be large, doc. not sort
[64] 146 Network error, port [x] [54] 148 Network error
[54] 149 Unsupported option in slot
22, 23 Plate [name of modified type] [printing position] in [paper source] 157 Place [adapted string] [picture mode] in multifunctional input 158 Place [name adapted species] [ print mode] In multifunctional import 158 Place[paper format] [printed position] [paper sources] 157 Location [paper size] [pressure level] in multiple operation input 158 place [paper type][printing mode] [copy source] 158 Place (paper format) [paper format ] [print mode] (print mode) in multifunction input 159
[x] [55] 155 Replacement of maintenance kit
[80.xy] 162 Wrong paper format. Open
disabled [56] 149 Print number exceeded.
[paper source] [34] 151 Insufficient memory to control the
Print job cancelled. 160 Print number exceeded.
sorting task [35] 152 Insufficient memory for
Print job not completed. 160 Image processing unit almost
defragmentation flash memory [35] 152 Insufficient memory for
empty [84.xy] 156 Image processing unit almost
empty, expected to print [x] pages [84.xy] 156 Cartridge almost empty [88.xY] 156 cartridge almost empty, to
Support for resource storage function [35] 152 Insufficient memory,
some tasks on hold are not recovered [35] 153 Insufficient memory,
Expect to print [x] pages [88.xy] 156 Cartridge and
some tasks have been taken off hold
image processing unit not matching [41.xy] 155

Insufficient free space in
drawer problems 166 printer software install 19 printer driver
flash memory for sources [52] 153 Paper short [34] 149 Parallel port disabled
disabled [56] 154 Default USB port
disabled [56] 154 Too many flash options installed
Add hardware options 20 troubleshooting
[56] 160 Plate [name of modified species]
[58] 154 Overcharged
Solving 163 cannot be Embedded Web Server
[printing position] in [paper source] 157 Place [adapted string]
[58] 155 Load too much. Remove loading.
open 196 non-reacting printer
[58] 150 Executable drawer vol. Remove
[print mode] in multifunction input 158 Place [name of modified type]
check 163 problems solving, printing
Paper. 146 Replace
printing goes slower 170 print job takes longer than
[printing position] in multifunction input 158 Place [paper format]
Image processing unit. Estimated number of remaining pages is 0 [84.xy] 162 Replace cartridge, region code
Expect 173, 175 there will be unexpected page-
[printing position] in [paper source] 157 Place [paper format]
ends for 173 curly paper 180 large printing tasks are not
cartridge does not match code printer [42.xy] 161 Replace cartridge. Estimated
[printing position] in multifunctional input 158 Place [paper type]
sorted 172 load link failed 172 multilingual PDF files
number of remaining pages is 0 [88.xy] 161 Replace unsupported
[paper format] [printing position] in [paper source] 158 Place [paper type]
not printed 174 paper runs regularly
image processing unit [32.xy] 162 Replace unsupported
fixed 168 task is printed on
[paper format] [print mode] in multifunctional input 159 Place [string for
wrong paper 171 task is printed from
cartridge [32.xy] 162 Remove paper from
modified paper] [printing position] in [paper source] 157 Place input tray [x] 157 place missing or non-
wrong drawer 171 tasks on hold are not
output drawer 153 Little memory, sources not
print 175 tasks not printed
stored [35] 148 Change [paper source] in
print 169 pages blocked
Responding image processing unit back [31.xy] 161 Place missing or non-
[adapted series] places [printing position] 146, 150 Change [paper source] in
not reprinted 167, 169 wrong margins on
[adapted generic name] place [printing position] 147, 150 Change [paper source]
Responding cartridge back [31.xy] 160 Restart printer.
print 179 wrong characters
printed 171 troubleshooting, printing quality
[paper format] place 147, 150 Change [paper source] in
Check last task. 149 Reference invalid.
Print job cancelled. 156 Serial option [x] error [54] 153 Close front valve 156 SMTP server is not set.
print is too dark 183 print is light 184 printing quality on transparencies
[type of paper] [size of paper ], location [position of print] 147, 151 printer security
is only 188 gray background on
Consult the system administrator. 154, 155 Software error in
information about 77 printer configurations 11 printer options, troubleshooting
print 178 repeated print failures on
default network [54] 154 Software error network [x]
print 182 horizontal interruptions on

![Page 213 of the Lexmark MS415 user manual — W Little memory, sources not stored [35] 148](/cdn/reader/11/11c90aaaab7020db2ca4325302eeffdfad3e10338dfcaae2d5335733926fabfc/images/page-213.webp?w=400)
Change [paper source] in [adjusted series] places [print mode] 146, 150 Modify [paper resource] to [additives generic name] places[print mode ] 147, 150 Mods [paper sources] to[print format] places (print mode) 147, 150 Change [ paper source] to (paper type] [paper size], place [printing mode] 147, 151 Wireless Setup Utility
use configuration 22 locking, security 75 moving printer 11, 144 differences in printing density 194 vertical interruptions on printing 192 vertical stripes on printing 190 confidential print jobs 59 confidential data
Security Information 77 Replace image processing unit. Estimated number of remaining pages is 0 [84.xy] 162 Replace cartridge, region code of cartridge does not match code printer [42.xys] 161 Replace cartridges. Estimated number of remaining pages is 0 [88.xy] 161 Replace unsupported image processing unit [32.xY] 162 Replace non-supported cartridge [32,xy ] 162
use 24 Wireless Setup Utility 24 erase, non-volatile memory 76 wipe, volatile memory 75 wizard for wireless configuration
Z economical handling of supplies 62
image processing unit 142 toner cartridge 141 Remove paper from output tray 153 virtual display, printer control panel
with the Embedded Web
Server 69 Virtual Display
Web Server 69 volatile memory 75
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.