
User's Guide
Machine type(s):
Models:
081, 230, 238, 436, 486, 496, 636, 638, 686, 698, 836, 838, 898


Conventions
Different types of caution statements include:
Safety information 7

CAUTION—POTENTIAL INJURY: Do not cut, twist, bind, crush, or place heavy objects on the power cord. Do not subject the power cord to abrasion or stress. Do not pinch the power cord between objects such as furniture and walls. If any of these things happen, a risk of fire or electrical shock results. Inspect the power cord regularly for signs of such problems. Remove the power cord from the electrical outlet before inspecting it.
CAUTION—SHOCK HAZARD: To avoid the risk of electrical shock, if you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
Safety information 8

This product is designed, tested, and approved to meet strict global safety standards with the use of specific manufacturer's components. The safety features of some parts may not always be obvious. The manufacturer is not responsible for the use of other replacement parts.
Refer service or repairs, other than those described in the user documentation, to a service representative.
This product uses a printing process that heats the print media, and the heat may cause the media to release emissions. You must understand the section in your operating instructions that discusses the guidelines for selecting print media to avoid the possibility of harmful emissions.
This product may produce small amounts of ozone during normal operation, and may be equipped with a filter designed to limit ozone concentrations to levels well below the recommended exposure limits. To avoid high ozone concentration levels during extensive usage, install this product in a well-ventilated area and replace the ozone and exhaust filters if instructed to do so in the product maintenance instructions. If there are no references to filters in the product maintenance instructions, then there are no filters requiring replacement for this product.
SAVE THESE INSTRUCTIONS.
Safety information 9

Learning about the printer 10
Finding information about the printer

Learning about the printer 11


Learning about the printer 12
Operating temperature 10 to 32.2°C (50 to 90°F)


Learning about the printer 13
Depending on your printer model, you can configure your printer by adding an optional 650‑sheet duo tray or both the 650‑sheet duo tray and 550‑sheet tray. For more information, see “Installing optional trays” on page 246.

1 Automatic document feeder (ADF)
5 Standard 250‑sheet tray
6 Optional 650‑sheet duo tray
2 ADF tray · 3 Standard bin · 4 ADF bin

Learning about the printer 14
7 Optional 550‑sheet tray

8 Manual feeder · 9 Control panel

Learning about the printer 15
1 LINE port Connect the printer to an active telephone line through a standard wall jack (RJ‑11), DSL filter, or VoIP adapter, or any other adapter that allows you to access the telephone line to send and receive faxes.
2 Power cord socket Connect the printer to a properly grounded electrical outlet.
3 USB port Attach a keyboard or any compatible option.
4 USB printer port Connect the printer to a computer.
5 Ethernet port Connect the printer to a network.
Use the To

Using the control panel 16
Lexmark CX421, MC2325, and MC2425 MFPs

1 Display View printing options, printer status, and error messages.
4 Address book button View the stored addresses.
5 Redial button View the last number dialed.
6 Numeric keypad Enter numbers or symbols in an input field.
7 Power button • Turn on or turn off the printer.
8 Stop or Cancel button Stop the current printer task.
9 Start button Start a printer task, depending on which mode is selected.
10 Pause button Place a dial pause in a fax number.
11 Backspace button Move the cursor backward and delete a character in an input field.
12 Fax button Send faxes.
13 Indicator light Check the printer status.
14 Back button Return to the previous screen.
15 Home button Go to the home screen.
Use the To

Using the control panel 17

2 Home button Go to the home screen.
3 Numeric keypad Enter numbers or symbols in an input field.
4 Power button • Turn on or turn off the printer.
5 Clear all or Reset button Reset the default settings of a function such as copying, faxing, or scanning.
6 Stop or Cancel button Stop the current printer task.
7 Start button Start a job, depending on which mode is selected.
8 Pause button Place a dial pause in a fax number.
9 Backspace button Move the cursor backward and delete a character in an input field.
10 Indicator light Check the printer status.
11 Volume buttons Adjust the speaker volume.
Use the To

Using the control panel 18

2 Home button Go to the home screen.
3 Power button • Turn on or turn off the printer.
4 Numeric keypad Enter numbers or symbols in an input field.
5 Pause button Place a dial pause in a fax number.
6 Start button Start a job, depending on which mode is selected.
7 Clear all or Reset button Reset the default settings of a function such as copying, faxing, or scanning.
8 Stop or Cancel button Stop the current printer task.
9 Backspace button Move the cursor backward and delete a character in an input field.
10 Indicator light Check the status of the printer.
11 Volume buttons Adjust the speaker volume.
12 Speaker port Attach a speaker.
Indicator light Printer status
Off The printer is off or in Hibernate mode.
Blue The printer is ready or processing data.
Use the To

Using the control panel 19
Indicator light Printer status
Red The printer requires user intervention.
Power button light Printer status
Off The printer is off, ready, or processing data.
Solid amber The printer is in Sleep mode.
Blinking amber The printer is in Hibernate mode.

Setting up and using the home screen applications 20

1 Copy Make copies.
2 E‑mail Send e‑mails.
3 Settings Access the printer menus.
4 Fax Send fax.
5 Address Book Manage a contact list that other applications on the printer can access.
8 Job Queue Show all the current print jobs.
9 Held Jobs Show the print jobs that are held in the printer memory.
10 Shortcut Center Organize all shortcuts.
11 App Profiles Access application profiles.
12 Scan Profiles Scan and save documents directly to the computer.
Touch To

Setting up and using the home screen applications 21
13 FTP Scan and save documents directly to an FTP server.
14 Bookmarks Organize all bookmarks.
15 Change Language Change the language on the display.
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Settings > Device > Visible Home Screen Icons.
3 Select the icons that you want to appear on the home screen.
4 Apply the changes.
Before using the application, make sure to do the following:
1 From the Screen Saver and Slideshow Images section, add, edit, or delete an image.
2 Apply the changes.
1 From the home screen, touch Change Wallpaper.
2 Select an image to use.
3 Apply the changes.
Touch To

Setting up and using the home screen applications 22
1 Insert a flash drive into the USB port.
2 From the home screen, touch Slideshow.
Images appear in alphabetical order.
1 From the home screen, touch Scan Center.
2 Select and create a destination, and then configure the settings.
3 Apply the changes.
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Apps > Card Copy > Configure.
3 Apply the changes.

Setting up and using the home screen applications 23
1 From the home screen, touch Shortcut Center, and then select a printer function.
2 Touch Create Shortcut, and then configure the settings.
3 Touch Save, and then type a unique shortcut name.
4 Apply the changes.
We recommend logging in to the printer before you create a profile. To enable a login method, see the Embedded Web Server ‑ Security Admin Guide.
1 From the home screen, touch Cloud Connector.
2 Select a cloud service provider.
3 Touch Create a Profile or .
4 Type a unique profile name.
5 If necessary, enter a PIN.
6 Touch Create, and then take note of the authorization code.
7 Open a web browser, and then go to https://lexmark.cloud-connect.co.
8 Click Next, and then accept the Terms of Use.
9 Enter the authorization code, and then click Connect.
10 Log in to your cloud service provider account.
11 Grant permissions.
You may need administrative rights to access the application.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Apps > Device Quotas > Configure.

Setting up and using the home screen applications 24
3 From the User Accounts section, add or edit a user, and then set the user quota.
4 Apply the changes.
You may need administrative rights to access the application.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Apps > QR Code Generator > Configure.
4 Apply the changes.
1 From the home screen, touch Eco‑Settings.
2 Configure Eco‑Mode or Schedule Power Modes.
3 Apply the changes.
1 From the home screen, touch Customer Support.
2 Print or e‑mail the information.
Use bookmarks to print frequently accessed documents that are stored in servers or on the web.
1 Open a web browser, and then type the printer IP address in the address field.

Setting up and using the home screen applications 25
2 Click Bookmark Setup > Add Bookmark, and then type a unique name for the bookmark.
To limit access to the bookmark, enter a PIN.
4 Click Save.
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Bookmark Setup > Add Folder, and then type a unique name for the folder.
3 Click Save.

Setting up and using the home screen applications 26
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Address Book.
3 From the Contacts section, add a contact.
4 If necessary, specify a login method to allow application access.
5 Apply the changes.
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Address Book.
3 From the Contact Groups section, add a group name.
4 Apply the changes.
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Address Book.

Setting up and using the home screen applications 27
4 Apply the changes.
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Address Book.

Setting up and using the accessibility features 28
1 Press and hold the 5 key until you hear a voice message.
2 Select OK.
1 Press and hold the 5 key until you hear a voice message.
2 Press Tab to navigate the focus cursor to the OK button, and then press Enter.
Double‑tap Select an option or item on the screen.
Triple‑tap Zoom in or zoom out text and images.
Swipe right or swipe down Move to the next item on the screen.
Swipe left or swipe up Move to the previous item on the screen.
Pan Access parts of the zoomed image that are beyond the limits of the screen.
Swipe up then left Exit an application and return to the home screen.
Gesture Function

Setting up and using the accessibility features 29
Swipe up then down Repeat a spoken prompt.
1 From the control panel, press and hold the 5 key until you hear a voice message.
2 Select Magnification mode.
3 Select OK.
For more information on navigating a magnified screen, see “Navigating the screen using gestures” on page 28.
1 From the home screen, select Settings > Device > Accessibility > Speech Rate.
2 Select the speech rate.
Do one or more of the following:
1 From the home screen, select Settings > Device > Accessibility > Speak Passwords/PINs.
2 Enable the setting.
Gesture Function

Loading paper and specialty media 30
Setting the paper size and type
1 From the control panel, navigate to:
Settings > Paper > Tray Configuration > Paper Size/Type > select a paper source
For non-touch-screen printer models, press to navigate through the settings.
2 Set the paper size and type.
1 From the control panel, navigate to:
Settings > Paper > Media Configuration > Universal Setup
For non-touch-screen printer models, press to navigate through the settings.
2 Configure the settings.
1 Remove the tray.

2 Adjust the guides to match the size of the paper that you are loading.

Loading paper and specialty media 31

3 Flex, fan, and align the paper edges before loading.

4 Load the paper stack with the printable side faceup, and then make sure that the side guides fit snugly against the paper.


Loading paper and specialty media 32

5 Insert the tray.
If necessary, set the paper size and paper type from the control panel to match the paper loaded.
1 Open the multipurpose feeder.

2 Adjust the guide to match the size of the paper that you are loading.


Loading paper and specialty media 33
3 Flex, fan, and align the paper edges before loading.
4 Load paper with the printable side facedown. • Load letterhead with the printable side facedown and the top edge entering the printer first for one‑sided printing.



5 From the control panel, set the paper size and paper type to match the paper loaded.

Loading paper and specialty media 34
1 Adjust the guide to match the size of the paper that you are loading.

2 Load a sheet of paper with the printable side facedown. • Load letterhead with the printable side facedown and the top edge entering the printer first for one‑sided printing.



3 Feed the paper until its leading edge gets pulled in.
1 Open a web browser, and then type the printer IP address in the address field.

Loading paper and specialty media 35
2 Click Settings > Paper > Tray Configuration.
3 Set the same paper size and paper type for the trays that you are linking.
4 Save the settings.
5 Click Settings > Device > Maintenance > Configuration Menu > Tray Configuration.
6 Set Tray Linking to Automatic.
7 Save the settings.
To unlink trays, make sure that no trays have the same paper size and paper type settings.

Supported paper sizes
Note: Your printer model may have a 650‑sheet duo tray, which consists of a 550‑sheet tray and an integrated 100‑sheet multipurpose feeder. The 550‑sheet tray of the 650‑sheet duo tray supports the same paper sizes as the optional 550‑sheet tray. The integrated multipurpose feeder supports different paper sizes, types, and weights.
Paper size and dimension
Standard 250‑sheet tray Manual
Optional 650‑sheet duo tray Optional 550‑sheet tray
printing 550‑sheet tray
210 x 297 mm (8.27 x 11.7 in.)
148 x 210 mm (5.83 x 8.27 in.)
105 x 148 mm (4.13 x 5.83 in.)
182 x 257 mm (7.17 x 10.1 in.)
215.9 x 279.4 mm (8.5 x 11 in.)
Legal 215.9 x 355.6 mm (8.5 x 14 in.)
184.2 x 266.7 mm (7.25 x 10.5 in.)
215.9 x 340.4 mm (8.5 x 13.4 in.)
1 Load this paper size into tray 1 and the manual feeder with the long edge entering the printer first.
2 Load this paper size into tray 2, tray 3, and the multipurpose feeder with the short edge entering the printer first.
3 When Universal is selected, the page is formatted for 215.9 x 355.6 mm (8.5 x 14 in.) unless the size is specified by the software application.
4 Load narrow paper with the short edge entering the printer first.
5 When Other Envelope is selected, the page is formatted for 215.9 x 355.6 mm (8.5 x 14 in.) unless the size is specified by the software application.

Paper size and dimension
Standard 250‑sheet tray Manual
Optional 650‑sheet duo tray Optional 550‑sheet tray
printing 550‑sheet tray
215.9 x 330.2 mm (8.5 x 13 in.)
139.7 x 215.9 mm (5.5 x 8.5 in.)
100 x 148 mm (3.94 x 5.83 in.)
98.4 x 148 mm to 215.9 x 355.6 mm (3.87 x 5.83 in. to 8.5 x 14 in.)
76.2 x 127 mm to 215.9 x 355.6 mm (3 x 5 in. to 8.5 x 14 in.)
148 x 210 mm to 215.9 x 355.6 mm (5.83 x 8.27 in. to 8.5 x 14 in.)
210 x 250 mm to 215.9 x 355.6 mm (8.27 x 9.84 in. to 8.5 x 14 in.)
98.4 x 190.5 mm (3.875 x 7.5 in.)
9 Envelope 98.4 x 225.4 mm (3.875 x 8.9 in.)
1 Load this paper size into tray 1 and the manual feeder with the long edge entering the printer first.
2 Load this paper size into tray 2, tray 3, and the multipurpose feeder with the short edge entering the printer first.
3 When Universal is selected, the page is formatted for 215.9 x 355.6 mm (8.5 x 14 in.) unless the size is specified by the software application.
4 Load narrow paper with the short edge entering the printer first.
5 When Other Envelope is selected, the page is formatted for 215.9 x 355.6 mm (8.5 x 14 in.) unless the size is specified by the software application.

Paper size and dimension
Standard 250‑sheet tray Manual
Optional 650‑sheet duo tray Optional 550‑sheet tray
printing 550‑sheet tray
104.8 x 241.3 mm (4.12 x 9.5 in.)
110 x 220 mm (4.33 x 8.66 in.)
162 x 229 mm (6.38 x 9.01 in.)
176 x 250 mm (6.93 x 9.84 in.)
Monarch 98.425 x 190.5 mm (3.875 x 7.5 in.)
98.4 x 162 mm to 176 x 250 mm (3.87 x 6.38 in. to 6.93 x 9.84 in.)
1 Load this paper size into tray 1 and the manual feeder with the long edge entering the printer first.
2 Load this paper size into tray 2, tray 3, and the multipurpose feeder with the short edge entering the printer first.
3 When Universal is selected, the page is formatted for 215.9 x 355.6 mm (8.5 x 14 in.) unless the size is specified by the software application.
4 Load narrow paper with the short edge entering the printer first.
5 When Other Envelope is selected, the page is formatted for 215.9 x 355.6 mm (8.5 x 14 in.) unless the size is specified by the software application.


Optional 650‑sheet duo tray Optional 550‑sheet tray

Optional 650‑sheet duo tray Optional 550‑sheet tray
1 Paper less than 75 g/m2 (20 lb) must be printed with Paper Type set to Light Paper. Failure to do so may cause excessive curl which can lead to feeding errors, especially in more humid environments.
2 Labels and other specialty media are supported for occasional use and must be tested for acceptability.
3 Paper labels up to 105 g/m2 (28‑lb bond) are supported.
4 100% cotton content maximum weight is 24‑lb bond.
5 28‑lb bond envelopes are limited to 25% cotton content.
Paper support 39


Optional 650‑sheet duo tray Optional 550‑sheet tray
1 Paper less than 75 g/m2 (20 lb) must be printed with Paper Type set to Light Paper. Failure to do so may cause excessive curl which can lead to feeding errors, especially in more humid environments.
2 Labels and other specialty media are supported for occasional use and must be tested for acceptability.
3 Paper labels up to 105 g/m2 (28‑lb bond) are supported.
4 100% cotton content maximum weight is 24‑lb bond.
5 28‑lb bond envelopes are limited to 25% cotton content.
Paper support 40

Printing from a computer
1 From the document that you are trying to print, open the Print dialog.
2 If necessary, adjust the settings.
3 Print the document.
LexmarkTM Mobile Print allows you to send documents and images directly to a supported Lexmark printer.
1 Open the document, and then send or share the document to Lexmark Mobile Print.
2 Select a printer.
3 Print the document.
Google Cloud PrintTM is a mobile printing service that allows enabled applications on mobile devices to print to any Google Cloud Print‑ready printer.
1 From the home screen of your mobile device, launch an enabled application.
2 Tap Print, and then select a printer.
3 Print the document.
Mopria® Print Service is a mobile printing solution for mobile devices running on AndroidTM version 4.4 or later. It allows you to print directly to any Mopria‑certified printer.
1 From the home screen of your mobile device, launch a compatible application.
2 Tap Print, and then select the printer.
3 Send the print job.
Printing 41

AirPrint is a mobile printing solution that allows you to print directly from Apple devices to an AirPrint‑certified printer.
1 From the home screen of your mobile device, launch a compatible application.
2 Select an item to print, and then tap the share icon.
3 Tap Print, and then select a printer.
4 Print the document.
1 Insert the flash drive.

2 Select the document that you want to print.
If necessary, configure other print settings.
3 Print the document.
To print another document, select USB Drive.
Printing 42


– The printer supports high‑speed USB flash drives with full‑speed standard. – USB flash drives must support the File Allocation Table (FAT) system.
Printing 43 · Documents

1 From the control panel, navigate to:
Settings > Security > Confidential Print Setup
For non‑touch‑screen printer models, press to navigate through the settings.
2 Configure the settings.
Max Invalid PIN Set the number of times an invalid PIN can be entered.
Set the expiration time for confidential print jobs.
Repeat Job Expiration Set the expiration time for a repeat print job.
Verify Job Expiration Set the expiration time that the printer prints a copy before printing the remaining copies.
Reserve Job Expiration Set the expiration time that the printer stores print jobs.
Require All Jobs to be Held
Set the printer to hold all print jobs.
1 With a document open, click File > Print.
2 Click Properties, Preferences, Options, or Setup.
3 Click Print and Hold.
4 Select Use Print and Hold, and then assign a user name.
5 Select the print job type (Confidential, Repeat, Reserve, or Verify).
If the print job is confidential, then enter a four‑digit PIN.
6 Click OK or Print.
Printing 44 · Use To · Confidential Job Expiration

1 With a document open, choose File > Print.
If necessary, click the disclosure triangle to see more options.
2 From the print options or Copies & Pages menu, choose Job Routing.
3 Select the print job type (Confidential, Repeat, Reserve, or Verify).
If the print job is confidential, then assign a user name and a four‑digit PIN.
4 Click OK or Print.
1 From the home screen, touch Cloud Connector.
2 Select a cloud service provider, and then select a profile.
3 Select a file.
4 If necessary, change the settings.
5 Touch Print.
1 From the control panel, navigate to:
Settings > Reports > Print > Print Fonts
For non-touch-screen printer models, press to navigate through the settings.
2 Select a font sample.
Printing 45

From the control panel, navigate to:
Settings > Reports > Print > Print Directory
For non-touch-screen printer models, press to navigate through the settings.
Printing 46

Using the automatic document feeder and scanner glass
Automatic document feeder (ADF) Scanner glass


1 Load an original document into the ADF tray or on the scanner glass.
2 From the control panel, select Copy, and then specify the number of copies.
If necessary, adjust the other settings.
3 Copy the document.
1 Place a photo on the scanner glass.
2 From the control panel, navigate to:
Copy > Settings > Content > Content Type > Photo
For non-touch-screen printer models, press to navigate through the settings.
3 From the Content Source menu, select the setting that best matches the original photo.
4 Copy the document.
Copying 47

1 Load an original document into the ADF tray or on the scanner glass.
2 From the control panel, navigate to:
Copy > Copy From > select the size of the original document > Copy To > select a paper source
If you are loading into the multipurpose feeder, then navigate to:
Copy To > Multipurpose Feeder > select a paper size > Letterhead
For non-touch-screen printer models, press to navigate through the settings.
3 Copy the document.
1 Load an original document into the ADF tray or on the scanner glass.
2 From the control panel, navigate to:
Copy > Settings > Paper Setup
For non-touch-screen printer models, press to navigate through the settings.
3 Adjust the settings.
4 Copy the document.
1 Load an original document into the ADF tray or on the scanner glass.
2 From the control panel, navigate to:
Copy > Settings > Scale > specify a scale value
For non-touch-screen printer models, press to navigate through the settings.
3 Copy the document.
1 Load an original document into the ADF tray or on the scanner glass.
2 From the control panel, navigate to:
Copy > Settings > Collate > On [1,2,1,2,1,2]
3 Copy the document.
Copying 48

1 Load an original document into the ADF tray or on the scanner glass.
2 From the control panel, navigate to:
Copy > Settings > Separator Sheets > On
For non-touch-screen printer models, press to navigate through the settings.
3 Adjust the settings.
4 Copy the document.
1 Load an original document into the ADF tray or on the scanner glass.
2 From the control panel, navigate to:
Copy > Settings > Pages Per Side
For non-touch-screen printer models, press to navigate through the settings.
3 Adjust the settings.
4 Copy the document.
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Shortcuts > Add Shortcut.
3 From the Shortcut Type menu, select Copy, and then configure the settings.
4 Apply the changes.
Copying 49

Using the automatic document feeder and scanner glass
Automatic document feeder (ADF) Scanner glass
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Settings > E‑mail > E‑mail Setup.
3 Configure the settings.
4 Apply the changes.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > E-mail.
E-mailing 50

3 Enter the needed information.
4 Apply the changes.
1 Load an original document into the ADF tray or on the scanner glass.
2 From the control panel, select E-mail, and then enter the needed information.
For non‑touch‑screen printer models, press #, and then enter the shortcut number using the keypad.
3 If necessary, configure the output file type settings.
4 Send the e-mail.
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Shortcuts > Add Shortcut.
3 From the Shortcut Type menu, select E‑mail, and then configure the settings.
4 Apply the changes.
E-mailing 51

Setting up the printer to fax

1 From the control panel, navigate to:
Settings > Device > Preferences > Run Initial Setup
For non-touch-screen printer models, press to navigate through the settings.
2 Turn off the printer, wait for about 10 seconds, and then turn on the printer.
3 From the Before You Begin screen, select Change the Settings and Continue with the Wizard.
4 From the Fax/Email Server Setup screen, enter the needed information.
5 Finish the setup.
Faxing 52


1 Connect one end of the telephone cable to the line port of the printer.
2 Connect the other end of the cable to an active analog wall jack.
Faxing 53

Connected to different wall jacks

1 Connect one end of the telephone cable to the line port of the printer.
2 Connect the other end of the cable to an active analog wall jack.
Faxing 54

Setting up fax in countries or regions with different telephone wall jacks and plugs
The standard wall jack adopted by most countries or regions is RJ11. If the wall jack or equipment in your facility is not compatible with this type of connection, then use a telephone adapter. An adapter for your country or region may not come with your printer, and you may need to purchase it separately.
There may be an adapter plug installed in the telephone port of the printer. Do not remove the adapter plug from the telephone port of the printer if you are connecting to a serial or cascaded telephone system.

Part name Part number
Lexmark adapter plug 40X8519
Faxing 55


1 Connect one end of the telephone cable to the line port of the printer.
2 Connect the other end of the cable to the RJ11 adapter, and then connect the adapter to the wall jack.
3 If you want to connect another device with a non‑RJ11 connector to the same wall jack, then connect it directly to the telephone adapter.
Faxing 56

The German wall jack has two kinds of ports. The N ports are for fax machines, modems, and answering machines. The F port is for telephones. Connect the printer to any of the N ports.

1 Connect one end of the telephone cable to the line port of the printer.
2 Connect the other end of the cable to the RJ11 adapter, and then connect the adapter to an N port.
3 If you want to connect a telephone and answering machine to the same wall jack, then connect the devices as shown.
A distinctive ring service lets you have multiple telephone numbers on one telephone line. Each telephone number is assigned a different ring pattern.
1 From the control panel, navigate to:
Settings > Fax > Analog Fax Setup > Fax Receive Settings > Admin Controls > Answer On
For non-touch-screen printer models, press to navigate through the settings.
2 Select a ring pattern.
Faxing 57

3 Apply the changes.
1 From the control panel, navigate to:
Settings > Device > Preferences > Date and Time > Configure
For non-touch-screen printer models, press to navigate through the settings.
2 Configure the settings.
1 From the control panel, navigate to:
Settings > Device > Preferences > Date and Time > Configure
For non-touch-screen printer models, press to navigate through the settings.
2 From the Time Zone menu, select (UTC+user) Custom.
3 Configure the settings.
Automatic document feeder (ADF) Scanner glass
Faxing 58

1 Load the original document into the ADF tray or on the scanner glass.
2 From the control panel, select Fax, and then enter the needed information.
3 If necessary, configure other fax settings.
4 Fax the document.
1 From the document that you are trying to fax, open the Print dialog.
2 Select the printer, and then click Properties, Preferences, Options, or Setup.
3 Click Fax > Enable fax, and then enter the recipient number.
4 If necessary, configure other fax settings.
5 Fax the document.
1 With a document open, choose File > Print.
2 Select the printer, and then enter the recipient number.
3 If necessary, configure other fax settings.
4 Fax the document.
1 Load the original document into the ADF tray or on the scanner glass.
2 From the control panel, navigate to:
Fax > To > enter the fax number > Done
For non-touch-screen printer models, press to navigate through the settings.
3 Select Send Time to configure the date and time, and then select Done.
If necessary, configure other fax settings.
4 Send the fax.
Faxing 59

1 Open a web browser, and then type the printer IP address in the address field.
2 Click Shortcuts > Add Shortcut.
3 From the Shortcut Type menu, select Fax, and then configure the settings.
4 Apply the changes.
1 Load an original document into the ADF tray or on the scanner glass.
2 From the control panel, select Fax, and then enter the needed information.
3 In the Resolution menu, select a setting.
4 Send the fax job.
1 Load an original document into the ADF tray or on the scanner glass.
2 From the control panel, select Fax, and then enter the needed information.
3 From the Darkness menu, adjust the setting.
4 Fax the document.
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Settings > Reports > Fax.
3 Click Fax Job Log or Fax Call Log.
Faxing 60

1 From the control panel, navigate to:
Settings > Fax > Analog Fax Setup > Fax Receive Settings > Admin Controls
For non-touch-screen printer models, press to navigate through the settings.
2 Set Block No Name Fax to On.
1 From the control panel, navigate to:
Settings > Fax > Analog Fax Setup > Fax Receive Settings > Holding Faxes
For non-touch-screen printer models, press to navigate through the settings.
2 Select a mode.
1 From the control panel, navigate to:
Settings > Fax > Analog Fax Setup > Fax Receive Settings > Admin Controls
For non-touch-screen printer models, press to navigate through the settings.
2 In the Fax Forwarding menu, select Print and Forward or Forward, and then configure the "Forward to" and fax destination settings.
Faxing 61

Using the automatic document feeder and scanner glass
Automatic document feeder (ADF) Scanner glass
1 Load the original document into the ADF tray or on the scanner glass.
2 From the control panel, select FTP, and then enter the needed information.
For non‑touch‑screen printer models, press #, and then enter the shortcut number using the keypad.
3 If necessary, configure other FTP settings.
4 Scan the document.
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Shortcuts > Add Shortcut.
Scanning 62

3 From the Shortcut Type menu, select FTP, and then configure the settings.
4 Apply the changes.
1 Load an original document into the ADF tray or on the scanner glass.
2 Insert the flash drive.
3 Select Scan to USB and adjust the settings if necessary.
4 Scan the document.
Scanning 63

1 Load an original document into the ADF tray or on the scanner glass.
2 From the control panel, navigate to:
Scan Profiles > Scan to Computer
For non-touch-screen printer models, press to navigate through the settings.
3 Select the scan profile where you want to save the document.
1 Load the document into the ADF tray or on the scanner glass.
2 From the home screen, touch Cloud Connector.
3 Select a cloud service provider, and then select a profile.
4 If necessary, select a folder.
5 Touch Scan.
6 If necessary, change the scan settings.
7 Touch Scan.
Scanning 64

Copy Copy Defaults · FTP FTP Defaults

Troubleshooting Print Quality Test Pages Cleaning the scanner
Set the language of the text that appears on the display.
Identify the country or region where the printer is configured to operate.
[List of countries or regions]
Run the setup wizard.
Select a language as a keyboard type.
Specify the information to appear on the home screen.
Display Text 1 [IP Address*] Display Text 2 [Date/Time*] Custom Text 1 Custom Text 2
Configure the printer date and time.
Current Date and Time Manually Set Date and Time Date Format [MM‑DD‑YYYY*] Time Format [12 hour A.M./P.M.*] Time Zone [GMT*]

Configure the settings for Network Time Protocol (NTP).
Enable NTP [On*] NTP Server Enable Authentication
Specify the unit of measurement for paper sizes.
U.S.* Metric
20–100% (100*) Adjust the brightness of the display.
Enable access to the flash drive.
Specify whether background removal is allowed.
Allow Custom Job scans
Scan multiple jobs to one file.
One Page Flatbed Scanning
Set copies from the scanner glass to only one page at a time.
Enable audio feedback for button presses, panel interactions, paper loaded prompts, and error notifications.
Adjust the volume of the printer speakers.
10–300 (60*) Set the idle time in seconds before the display shows the home screen, or before the printer logs off a user account automatically.

Connect an external Virtual Network Computing (VNC) client to the remote control panel.
Set the authentication type when accessing the VNC client server.
Set the indicator light to come on when a printer error occurs.
Enable a sound when loading paper into the ADF.
Set the number of times that the alarm sounds when the printer requires user intervention.
Show the estimated status of the supplies.
Show estimates* Do not show estimates
Set the number of times that the alarm sounds when the toner cartridge is low.
E‑mail Alerts Setup
Type the IP address or host name of the primary SMTP server for sending e-mail.
E‑mail Setup
E‑mail Alerts Setup
Enter the port number of the primary SMTP server.
E‑mail Setup
Primary SMTP Gateway Port

E‑mail Alerts Setup
Type the server IP address or host name of your secondary or backup SMTP server.
E‑mail Setup
E‑mail Alerts Setup
Enter the server port number of your secondary or backup SMTP server.
E‑mail Setup
Secondary SMTP Gateway Port
E‑mail Alerts Setup
Specify how long before the printer times out if the SMTP server does not respond.
E‑mail Setup
5‑30 seconds (30*)
E‑mail Alerts Setup
Specify a reply address in the e‑mail.
E‑mail Setup
E‑mail Alerts Setup
Use the SMTP default Reply Address.
E‑mail Setup
Always use SMTP default Reply Address
E‑mail Alerts Setup
Send an e‑mail using an encrypted link.
E‑mail Setup
E‑mail Alerts Setup
Require a trusted certificate when accessing the SMTP server.
E‑mail Setup
E‑mail Alerts Setup
Set the authentication type for the SMTP server.
E‑mail Setup
No authentication required* Login / Plain NTLM CRAM‑MD5 Digest‑MD5 Kerberos 5

E‑mail Alerts Setup
Set whether credentials are required for device‑initiated e‑mails.
E‑mail Setup
Device‑Initiated E‑mail
None* Use Device SMTP Credentials
E‑mail Alerts Setup
Set whether credentials are required for user‑initiated e‑mails.
E‑mail Setup
User‑Initiated E‑mail
None Use Device SMTP Credentials Use Session User ID and Password Use Session E‑mail address and Password* Prompt user
E‑mail Alerts Setup
Enable user credentials and group designations to connect to the SMTP server.
E‑mail Setup
Use Active Directory Device Credentials
E‑mail Alerts Setup
Specify the user ID to connect to the SMTP server.
E‑mail Setup
E‑mail Alerts Setup
Specify the password to connect to the SMTP server.
E‑mail Setup
E‑mail Alerts Setup
Specify the realm for the Kerberos 5 authentication protocol.
E‑mail Setup
E‑mail Alerts Setup
Specify the domain name for the NTLM security protocol.
E‑mail Setup
E‑mail Alerts Setup
Disable an SMTP setup error message to appear on the display.
E‑mail Setup
Disable “SMTP server not set up” error
Set the printer to flush blank pages or pages with partial prints automatically after a jammed page has been cleared.

Let the printer continue processing or printing a job automatically after clearing certain printer conditions that require user intervention.
Off On* (5 seconds)
Set the printer to restart when an error occurs.
Reboot when idle Reboot always* Reboot never
Set the number of automatic reboots that the printer can perform.
Set the number of seconds before the printer performs an automatic reboot.
Show a read‑only information of the reboot counter.
Reset Auto Reboot Counter.
Reset Auto Reboot Counter
Set the printer to show a message when a short paper error occurs.
Display Short Paper Error
On Auto‑clear*
Set the printer to process the entire page into the memory before printing it.
Set the printer to reprint jammed pages.

Specify how to restart a scan job after resolving a paper jam.
Job level Page level*
Allow printing with the display turned off.
Print With Display Off
Display on when printing Allow printing with display off*
Set the idle time before the printer begins operating in Sleep mode.
Set the time before the printer enters Hibernate mode.
Disabled 1 hour 2 hours 3 hours 6 hours 1 day 2 days 3 days* 1 week 2 weeks 1 month
Set the printer to Hibernate mode even when an active Ethernet connection exists.
Hibernate Timeout on Connection
Hibernate Do Not Hibernate*
Minimize the use of energy, paper, or specialty media.
Off* Energy Energy/Paper Paper
Schedule the printer when to enter Sleep or Hibernate mode.

Information Sent to Lexmark
Send printer usage and performance information to Lexmark.
Supplies and Page Usage (Anonymous) Device Performance (Anonymous) Device Interaction (Anonymous) None of the Above
Start Time Stop Time
User Information ‑ Level
Anonymous Session Information Only* Session Information with Generic User Information Session Information with Actual User IDs
Duplicate Key Strike Interval
0–5 (0*) Set the interval in seconds during which the printer ignores duplicate key presses on an attached keyboard.
Key Repeat Initial Delay
0.25–5 (1*) Set the initial length of delay in seconds before a repeating key starts repeating.
0.5–30 (30*) Set the number of presses per second for a repeating key.
Let the user remain in the same location and reset the Screen Timeout timer when it expires instead of returning to the home screen.
1–10 (5*) Adjust the headphone volume.

Enable Voice Guidance When Headphone Is Attached
Enable Voice Guidance when a headphone is attached to the printer.
Set the printer to read out loud passwords or personal identification numbers.
Set the Voice Guidance speech rate.
Very Slow Slow Normal* Fast Faster Very Fast Rapid Very Rapid Fastest
Restore the printer factory default settings.
Restore all settings Restore printer settings Restore network settings Restore app settings
Change the USB driver mode of the printer to improve its compatibility with a personal computer.
USB Scan to Local
Set whether the USB device driver enumerates as a USB Simple device (single interface) or as a USB Composite device (multiple interfaces).

Set the USB port to run at full speed and disable its high‑speed capabilities.
Set the printer to link the trays that have the same paper type and paper size settings.
Show the Tray Insert message.
Show Tray Insert Message
Set the paper source that the user fills when a prompt to load paper or envelope appears.
Auto* Multipurpose Feeder Manual Paper Envelope Prompts
Auto* Multipurpose Feeder Manual Paper
Set the printer to resolve paper- or envelope-related change prompts.
Prompt user* Continue Use current
Print reports about printer menu settings, status, and event logs.
Menu Settings Page Event Log Event Log Summary HealthCheck Statistics
Supply Usage And Counters
Reset the supply usage history, such as number of pages and days remaining, to the factory shipped level.
Clear Supply Usage History
Supply Usage And Counters
Reset the counter after installing a new maintenance kit.
Supply Usage And Counters
Adjust the range for the amount of color coverage on the printed page.
Set the printer to recognize and use the PPDS data stream.

Set fax to enter Sleep mode whenever the printer determines that it should.
Fax Low Power Support
Disable Sleep Permit Sleep Auto*
Set the storage location for all faxes.
Print color content in grayscale.
Enhance the printed output to compensate for misregistration in the printer.
Off 1 2* 3 4 5
Set a text point-size value below which the high‑frequency screens are used when printing font data. For example, if the value is 24, then all fonts sized 24 points or less use the high‑frequency screens.
Set the printer to operate in Quiet Mode.
Enable access to the control panel menus.
Let printservice read and edit values from the Embedded Web Server.

Set the printer to operate in a special mode, in which it attempts to continue offering as much functionality as possible, despite known issues.
For example, when set to On, and the duplex motor is nonfunctional, the printer performs one‑sided printing of the documents even if the job is two‑sided printing.
Set the minimum memory allocation for storing copy jobs.
Erase user‑defined strings for the Default or Alternate custom messages.
Erase messages that were remotely installed.
Clear all remotely‑installed messages
Show existing error messages on the display after the printer remains inactive on the home screen for a length of time equal to the Screen Timeout setting.
Automatically Display Error Screens
Enable the printer to use the orientation setting under the Copy menu when sending quick copy jobs.
Honor orientation on fast path copy
Enable an optional parallel port.
Enable Optional Parallel Port
Toner patch sensor setup
Set the printer to put down the correct amount of toner to maintain color consistency.
Disabled Fewest color adjustment Fewer color adjustment Normal* Better color accuracy Best color accuracy
Toner patch sensor setup
Run the full color calibration.
Toner patch sensor setup
Print a diagnostic page that contains information on toner patch sensor calibration.
Print TPS information page

Enable the Lexmark Embedded Solutions (LES) applications.
Print a Quick Test target page.
Manually register the flatbed and ADF after replacing the ADF, scanner glass, or controller board.
Front ADF Registration Rear ADF Registration Flatbed Registration
Set the size, in millimeters, of the no‑print area around an ADF or flatbed scan job.
0–6 (3*) ADF Edge Erase
Set the printer to perform ADF mechanical skew adjustment.
Disable the scanner when it is not working properly.
Enabled* Disabled ADF Disabled
Set the byte order of a TIFF‑formatted scan output.
CPU Endianness* Little Endian Big Endian
Set the RowsPerStrip tag value of a TIFF‑formatted scan output.
Exact Tiff Rows Per Strip

Out of Service Erase
Show information on when the printer memory or hard disk was last sanitized.
Memory Last Sanitized Hard Disk Last Sanitized
Out of Service Erase
Clear all settings and applications that are stored in the printer memory or hard disk.
Sanitize all information on nonvolatile memory Sanitize all information on hard disk Erase all printer and network settings
Copy E-mail Fax Status/Supplies Job Queue Change Language Shortcut Center Address Book Bookmarks Held Jobs USB FTP Scan Profiles App Profiles Forms and Favorites Scan Center Card Copy
Specify which icons to show on the home screen.
Asset Tag1 Describe the printer. The maximum length is 32 characters.
Printer’s Location1 Identify the printer location. The maximum length is 63 characters.
Contact1 Personalize the printer name. The maximum length is 63 characters.
1 In some printer models, this menu item can be configured only from the Embedded Web Server.
2 This menu item appears only in some printer models.
Menu item Description · Menu Description · Menu item Description

Export Configuration File to USB2 Export configuration files to a flash drive.
Export Compressed Logs to USB2 Export compressed log files to a flash drive.
Send diagnostic information to Lexmark.
1 In some printer models, this menu item can be configured only from the Embedded Web Server.
2 This menu item appears only in some printer models.
Specify whether to print on one side or two sides of the paper.
1‑sided* 2‑sided
Determine which side of the paper (long edge or short edge) is bound when performing two‑sided printing.
Long Edge* Short Edge
Print blank pages that are included in a print job.
Print Do Not Print*
Keep the pages of a print job stacked in sequence, particularly when printing multiple copies of the job.
Off [1,1,1,2,2,2]* On [1,2,1,2,1,2]
Insert blank separator sheets when printing.
None* Between Copies Between Jobs Between Pages
Specify the paper source for the separator sheet.
Tray [x] (1*) Multipurpose Feeder

Print multiple page images on one side of a sheet of paper.
Off* 2 pages per side 3 pages per side 4 pages per side 6 pages per side 9 pages per side 12 pages per side 16 pages per side
Pages per Side Ordering
Specify the positioning of multiple page images when using Pages per Side.
Horizontal* Reverse Horizontal Vertical Reverse Vertical
Specify the orientation of a multiple‑page document when using Pages per Side.
Pages per Side Orientation
Pages per Side Border
Print a border around each page image when using Pages per Side.
1–9999 (1*) Specify the number of copies for each print job.
Set the printable area on a sheet of paper.
Normal* Fit to page Whole Page
Set the printer language.
PCL Emulation PS Emulation*
Preserve print jobs requiring supplies so that jobs not requiring the missing supplies can print.

0–255 (30*) Set the time in seconds that the printer waits for user intervention before it holds jobs that require unavailable resources and continues to print other jobs in the print queue.
Determine how the color imaging kit operates during printing.
Max Speed Max Yield*
Specify where to save all permanent resources, such as fonts and macros, that have been downloaded to the printer.
Determine what the printer does with downloaded resources, such as fonts and macros, when it receives a job that requires more than the available memory.
Specify the order when you choose to print all held and confidential jobs.
Alphabetical* Newest First Oldest First
Set the print mode.
Black and White Color*
Set the resolution for the printed output.
4800 CQ* 1200 dpi
1 to 5 (4*) Determine the lightness or darkness of text images.

Enhance the printed output to have smoother lines with sharper edges.
Reduce the amount of toner used to print graphics and images.
Adjust the brightness, contrast, and saturation for color output.
‑6 to 6 (0*)
0 to 5 (0*)
0 to 5 (0*)
Adjust the amount of toner that is used for each color.
‑5 to 5 (0*) Magenta
‑5 to 5 (0*) Yellow
‑5 to 5 (0*) Black
‑5 to 5 (0*) Reset Defaults
Modify the color settings used to print documents.
Print sample pages for each of the RGB and CMYK color conversion tables used in the printer.
Color Adjust Calibrate the printer to adjust color variations in the printed output.
Assign specific CMYK values to twenty named spot colors.

RGB Replacement Match the colors of the output with that of the original document.
Set the printer to create a log of the print jobs that it receives.
Specify how often the printer creates a log file.
Log Action at End of Frequency
Specify how the printer responds when the frequency threshold expires.
None* E‑mail Current Log E‑mail & Delete Current Log Post Current Log Post & Delete Current Log
Log Near Full Level
Specify the maximum size of the log file before the printer executes the Log Action at Near Full.
Log Action at Near Full
Specify how the printer responds when the hard disk is nearly full.
None* E‑mail Current Log E‑mail & Delete Current Log E‑mail & Delete Oldest Log Post Current Log Post & Delete Current Log Post & Delete Oldest Log Delete Current Log Delete Oldest Log Delete All But Current Delete All Logs

Log Action at Full
Specify how the printer responds when disk usage reaches the maximum limit (100MB).
None* E‑mail & Delete Current Log E‑mail & Delete Oldest Log Post & Delete Current Log Post & Delete Oldest Log Delete Current Log Delete Oldest Log Delete All But Current Delete All Logs
URL to Post Log Specify where the printer posts job accounting logs.
E‑mail Address to Send Logs Specify the e‑mail address to which the printer sends job accounting logs.
Log File Prefix Specify the prefix for the log file name.
Print a test page that contains information on errors, including XML markup errors.
1–30 (2*) Set the minimum stroke width.
Scale the page content to fit the selected paper size.
Specify whether to print annotations in the PDF.
Print Do Not Print*

Print a page that describes the PostScript® error.
1–30 (2*) Set the minimum stroke width.
Lock PS Startup Mode
Disable the SysStart file.
Enhance the contrast and sharpness of low‑resolution images.
Establish the font search order.
Set the printer to wait for more data before canceling a print job.
Off On* (40 seconds)
Choose the source which contains the default font selection.
Resident* Disk Flash All
Select a font from the specified font source.
[List of available fonts] (Courier*)

Specify the symbol set for each font name.
[List of available symbol set] (10U PC‑8*)
0.08–100 (10*) Specify the pitch for fixed or monospaced fonts.
Specify the orientation of text and graphics on the page.
1–255 Specify the number of lines of text for each page printed through the PCL® datastream.
PCL5 Minimum Line Width
1–30 (2*) Set the initial minimum stroke width.
PCLXL Minimum Line Width
Set the width of the logical page on A4‑size paper.
198 mm* 203 mm
Auto CR after LF
Set the printer to perform a carriage return after a line feed control command.
Auto LF after CR
Set the printer to perform a line feed after a carriage return control command.
Configure the printer to work with a different print driver or custom application that uses a different set of source assignments to request a given paper source.
Assign MP Feeder Assign Tray [x] Assign Manual Paper Assign Manual Envelope
Choose from the following options:
Off*—The printer uses the factory default paper source assignments. None—The paper source ignores the Select Paper Feed command. 0–199—Select a numeric value to assign a custom value to a paper source.

Show the factory default value assigned for each paper source.
Restore the tray renumber values to their factory defaults.
Set the printer to end a print job after it has been idle for the specified amount of time in seconds.
Set the font to use for HTML documents.
[List of fonts] (Times*)
1–255 (12*) Set the font size to use for HTML documents.
1–400% (100*) Scale HTML documents.
Set the page orientation for HTML documents.
8–255 mm (19*) Set the page margin for HTML documents.
Print background information or graphics for HTML documents.
Do Not Print Print*
Select the best available paper size and orientation setting for an image.
Invert bitonal monochrome images.

Adjust the image to fit the printable area.
Anchor Top Left Best Fit* Anchor Center Fit Height/Width Fit Height Fit Width
Specify the orientation of text and graphics on the page.
Portrait* Landscape Reverse Portrait Reverse Landscape
Set the paper source for all print jobs.
Tray [x] (1*) Multipurpose Feeder Manual Paper Manual Envelope
Specify the paper size or paper type loaded in each paper source.
Tray [x] Multipurpose Feeder Manual Paper Manual Envelope
Set the printer to substitute a specified paper size if the requested size is not loaded in any paper source.
Off Statement/A5 Letter/A4 All Listed*

Specify the unit of measurement for the universal paper.
Set the portrait width of the universal paper.
3–14.17 inches (8.50*) 76–359.91 mm (216*)
Set the portrait height of the universal paper.
3–14.17 inches (14*) 76–359.91 mm (356*)
Set the printer to pick paper from the short edge or long edge direction.
Short Edge* Long Edge
Custom Scan Size [x]
Assign a scan size name and configure the scan settings.
Scan Size Name Width
1–8.50 inches (8.50*) 25–216 mm (216*) Height
1–14 inches (14*) 25–356 mm (297*) Orientation
Portrait* Landscape 2 scans per side Off* On

Plain Card Stock Recycled Glossy Labels Vinyl Labels Bond Envelope Letterhead Preprinted Colored Paper Light Heavy Rough/Cotton Custom Type [x]
Specify the texture and weight of the paper loaded.
Improve the output result based on the content of the original document.
Text Text/Photo* Photo Graphics
Improve the output result based on the source of the original document.
Black and White Laser Color Laser* Inkjet Photo/Film Magazine Newspaper Press Other
Specify the scanning behavior based on the original document.
1 sided to 1 sided* 1 sided to 2 sided 2 sided to 1 sided 2 sided to 2 sided

Specify whether to insert blank separator sheets when printing.
None* Between Copies Between Jobs Between Pages
Specify the paper source for the separator sheet.
Tray [x] (1*) Multipurpose Feeder
Specify whether to print copies in color.
Specify the number of page images to print on one side of a sheet of paper.
Off* 2 Portrait pages 4 Portrait pages 2 Landscape pages 4 Landscape pages
Place a border around each image when printing multiple pages on a single page.
Print multiple copies in sequence.
Off [1,1,1,2,2,2] On [1,2,1,2,1,2]*
Set the paper size of the original document.
[List of paper sizes]
Specify the paper source for the copy job.
Tray [x] (1*) Multipurpose Feeder Auto Size Match
Specify whether to generate a cooler or warmer output.
‑4 to 4 (0*)
Adjust the darkness of the scanned image.
‑4 to 4 (0*)
1–9999 (1*) Specify the number of copies.

Apply a header or footer on the printed output.
Top left Top middle Top right Bottom left Bottom middle Bottom right
Specify the overlay text printed on each page of the copy job.
Confidential Copy Draft Urgent Custom Off*
Custom overlay Type a custom overlay text.
Adjust the amount of toner being used in each color.
‑4 to 4 (0*)
Specify which color to drop during scanning, and adjust the dropout setting for that color.
None* Red Green Blue
Set the amount of color that the printer detects from the original document.
1–9 (5*) Area Sensitivity

Specify the contrast of the output.
Best for Content* 0 1 2 3 4 5
Adjust the amount of background visible on a scanned image.
Content‑based* Fixed Level
‑4 to 4 (0*)
Align the content at the center of the page.
Create a mirror image of the original document.
Create a negative image of the original document.
Adjust the amount of shadow detail visible on a scanned image.
‑4 to 4 (0*)
Allow edge‑to‑edge scanning of the original document.
Scan Edge to Edge
1–5 (3*) Adjust the sharpness of a scanned image.
Print copies in color.
Interrupt a print job to copy a page or document.

Turn on scanning of custom jobs by default.
Allow Save as Shortcut
Save custom copy settings as shortcuts.
Sample Copy Print a sample copy.
Select a fax mode.
Analog* Fax Server Disabled
Fax Name Identify your fax machine.
Fax Number Identify your fax number.
Notify fax recipients of your fax name or fax number.
Fax Name Fax Number*
Set the printer to fax manually.

Set the amount of internal printer memory allocated for faxing.
All receive Mostly receive Equal* Mostly send All send
Cancel outgoing faxes before they are transmitted, or cancel incoming faxes before they finish printing.
Show the telephone number of the person sending the fax.
Specify the format for masking an outgoing fax number.
Off* From Left From Right
0–58 (0*) Specify the number of digits to mask in an outgoing fax number.
Enable Line Connected Detection
Determine whether a telephone line is connected to the printer.
Enable Line In Wrong Jack Detection
Determine whether a telephone line is connected to the correct port on the printer.
Enable Extension in Use Support
Determine whether a telephone line is used by another device such as another phone on the same line.
Optimize Fax Compatibility Configure the printer fax functionality for optimal compatibility with other fax machines.

Set the resolution of the scanned image.
Standard* Fine Super Fine Ultra Fine
Specify the size of the original document.
[List of paper sizes]
Specify the orientation of the original document.
Specify the page orientation of text and graphics when scanning a two‑sided document.
Off* Long Edge Short Edge
Improve the output result based on the content of the original document.
Text* Text/Photo Photo Graphics
Improve the output result based on the source of the original document.
Black and White Laser* Color Laser Inkjet Photo/Film Magazine Newspaper Press Other
Adjust the darkness of the scanned image.
‑4 to 4 (0*)
Set the printer to dial a fax number without waiting to recognize the dial tone.
Specify the dial mode for incoming or outgoing faxes.

Adjust the amount of toner used for each color.
‑4 to 4 (0*)
Specify which color to drop during scanning, and adjust the dropout setting for that color.
None* Red Green Blue
Set the contrast of the output.
Best for Content* 0 1 2 3 4 5
Adjust the amount of background visible on a scanned image.
Content‑based* Fixed Level
‑4 to 4 (0*)
Create a mirror image of the original document.
Create a negative image of the original document.
Adjust the amount of shadow detail visible on a scanned image.
‑4 to 4 (0*)
Scan Edge to Edge
Allow edge‑to‑edge scanning of the original document.

1–5 (3*) Adjust the sharpness of the scanned image.
Specify whether to generate a cooler or warmer output.
‑4 to 4 (0*)
0–9 (5*) Adjust the number of redial attempts based on the activity levels of recipient fax machines.
1–200 minutes (3*) Increase the time between redial attempts to increase the chance of sending fax successfully.
Activate Error Correction Mode (ECM) for fax jobs.
Fax documents that are scanned at the printer.
Allow the print driver to send fax.
Allow Save as Shortcut
Save fax numbers as shortcuts in the printer.
Set the maximum speed for sending fax.
33600* 14400 9600 4800 2400
Turn on scanning of custom jobs by default.
Show a preview of the scan on the display.

Enable Color Fax Scans
Enable color scans for fax.
Off by default* On by default Never use Always use
Auto Convert Color Faxes to Mono Faxes
Convert all outgoing color faxes to black and white.
Ask the user to confirm the fax number.
Dial Prefix Set a dialing prefix.
Establish a dialing prefix rule.
Remove fax jobs that request specific unavailable resources from the print queue.
None* Toner Toner and Supplies
1–25 (3*) Set the number of rings for incoming fax.
Scale incoming fax to fit on the page.
Set the paper source for printing incoming fax.
Tray [x] Multipurpose Feeder Auto*
Print on both sides of the paper.
Specify whether to insert blank separator sheets when printing.
None* Before Job After Job

Specify the paper source for the separator sheet.
Tray [x] (1*) Multipurpose Feeder
Specify the output bin for received faxes.
Print the transmission information at the bottom of each page from a received fax.
Fax Footer Time Stamp
Print the time stamp at the bottom of each page from a received fax.
Hold received faxes from printing until they are released.
Off* Always On Manual Scheduled
Set the printer to receive fax.
Enable Color Fax Receive
Set the printer to receive fax in color.
Show the number that is sending the incoming fax.
Block No Name Fax
Block incoming faxes sent from devices with no station ID or fax ID specified.
Specify the phone numbers that you want to block.

Set a distinctive ring pattern for incoming fax.
All Rings* Single Ring Only Double Ring Only Triple Ring Only Single or Double Rings Only Single or Triple Rings Only Double or Triple Rings Only
Set the printer to receive fax automatically.
0–9 (9*) Manually enter a code on the telephone number pad to begin receiving fax.
Specify how to forward received fax.
Print* Print and Forward Forward
Specify where to forward received fax.
Confirmation E‑mail Send a confirmation e‑mail when fax forwarding is successful.
Set the maximum speed for transmitting fax.
33600* 14400 9600 4800 2400

Configure the settings for the fax cover page.
Off by Default* On by Default Never Use Always Use
Message:
Print a log for successful fax transmission or transmission error.
Print log* Do Not Print Log Print Only For Error
Print a log for fax‑receive failures.
Print Never* Print on Error
Print all fax activity.

Specify the paper source for printing logs.
Tray [x] (1*) Multipurpose Feeder
Identify the sender by remote fax name or fax number.
Remote Fax Name* Dialed Number
View a summary of all fax jobs.
View a summary of fax dialing history.
Specify the output bin for printed logs.
Standard Bin* Bin [x]
Set the fax speaker mode.
Always Off Always On On until Connected*
Adjust the fax speaker volume.
Enable the ringer volume.
To Format Specify a fax recipient.

Reply Address Specify a reply address for sending fax.
Subject Specify the fax subject and message.
Set the printer to receive analog faxes.
Primary SMTP Gateway Type the IP address or host name of the primary Simple Mail Transfer Protocol (SMTP) server for sending e-mail.
Primary SMTP Gateway Port
1–65535 (25*) Enter the port number of the primary SMTP server.
Secondary SMTP Gateway Type the server IP address or host name of your secondary or backup SMTP server.
Secondary SMTP Gateway Port
1–65535 (25*) Enter the server port number of your secondary or backup SMTP server.
5–30 (30*) Set the time before the printer times out if the SMTP server does not respond.
Reply Address Specify a reply address for sending fax.
Always use SMTP default Reply Address
Specify the SMTP reply address for sending fax.
Specify whether to send fax using an encrypted link.
Specify a trusted certificate when accessing the SMTP server.
Set the authentication type for the SMTP server.
No authentication required* Login / Plain NTLM CRAM‑MD5 Digest‑MD5 Kerberos 5

Device‑Initiated E‑mail
Specify whether credentials are required for device‑initiated e‑mail.
None* Use Device SMTP Credentials
User‑Initiated E‑mail
Specify whether credentials are required for user‑initiated e‑mail.
None* Use Device SMTP Credentials Use Session User ID and Password Use Session E‑mail address and Password Prompt user
Use Active Directory Device Credentials
Enable user credentials and group destinations to connect to the SMTP server.
Device Userid Specify the user ID and password to connect to the SMTP server.
Kerberos 5 REALM Specify the realm for the Kerberos 5 authentication protocol.
NTLM Domain Specify the domain name for the NTLM security protocol.
Disable "SMTP server not set up" error
Hide the “SMTP server not set up” error message.
Specify the file format for the scanned image.
TIFF (.tif) PDF (.pdf)* XPS (.xps) TXT (.txt) RTF (.rtf) DOCX (.docx)
Improve the output result based on the content of the original document.
Text Text/Photo* Photo Graphics

Improve the output result based on the source of the original document.
Black and White Laser Color Laser* Inkjet Photo/Film Magazine Newspaper Press Other
Set the fax resolution.
Standard* Fine Super Fine Ultra Fine
1–9 (5*) Set the darkness of the output.
Specify the orientation of text and graphics on the page.
Set the paper size of the original document.
[List of paper sizes]
Use Multi‑Page TIFF
Choose between single‑ and multiple‑page TIFF files.
Primary SMTP Gateway Type the IP address or host name of the primary SMTP server for sending e- mail.
Primary SMTP Gateway Port
1–65535 (25*) Enter the port number of the primary SMTP server.

Secondary SMTP Gateway Type the server IP address or host name of your secondary or backup SMTP server.
Secondary SMTP Gateway Port
1–65535 (25*) Enter the server port number of your secondary or backup SMTP server.
5–30 seconds (30*) Set the time before the printer times out if the SMTP server does not respond.
Reply Address Specify a reply address in the e‑mail.
Always use SMTP default Reply Address
Always use the default reply address in the SMTP server.
Specify whether to send e‑mail using an encrypted link.
Require a trusted certificate when accessing the SMTP server.
Set the authentication type for the SMTP server.
No authentication required* Login / Plain NTLM CRAM‑MD5 Digest‑MD5 Kerberos 5
Device‑Initiated E‑mail
Specify whether credentials are required for device‑initiated e‑mail.
None* Use Device SMTP Credentials
User‑Initiated E‑mail
Specify whether credentials are required for user‑initiated e‑mail.
None* Use Device SMTP Credentials Use Session User ID and Password Use Session E‑mail address and Password Prompt user
Use Active Directory Device Credentials
Enable user credentials and group designations to connect to the SMTP server.

Device Userid Specify the user ID and password to connect to the SMTP server.
Kerberos 5 REALM Specify the realm for the Kerberos 5 authentication protocol.
NTLM Domain Specify the domain name for the NTLM security protocol.
Disable "SMTP server not set up" error
Hide the “SMTP server not set up” error message.
Subject Specify the e‑mail subject and message.
File Name Specify the file name for the scanned image.
Specify the file format for the scanned image.
PDF (.pdf)* TIFF (.tif) JPEG (.jpg) XPS (.xps) TXT (.txt) RTF (.rtf) DOCX (.docx)
Configure the settings for optical character recognition (OCR).
Recognized Languages Auto Rotate Despeckle Auto Contrast Enhance

Set the PDF format of the scanned image.
1.3 1.4 1.5* 1.6 1.7 Archival Version
A‑1a* A‑1b Highly Compressed
Off* On Archival (PDF/A)
Improve the output result based on the content of the original document.
Text Text/Photo* Photo Graphics
Improve the output result based on the original document.
Black and White Laser* Color Laser Inkjet Photo/Film Magazine Newspaper Press Other
Specify the color when scanning an image.
Black and White Gray Color* Auto

Set the resolution of the scanned image.
75 dpi 150 dpi* 200 dpi 300 dpi 400 dpi 600 dpi
Adjust the darkness of the scanned image.
-4 to 4 (0*)
Specify the orientation of text and graphics on the page.
Set the paper size of the original document.
[List of paper sizes]
Specify the page orientation of text and graphics when scanning a two‑sided document.
Off* Long Edge Short Edge
Adjust the color intensity during scanning.
-4 to 4 (0*) Magenta to Green
-4 to 4 (0*) Yellow to Blue
-4 to 4 (0*)
Specify which color to drop during scanning, and adjust the dropout setting for that color.
None* Red Green Blue Default Red Threshold
0–255 (128*) Default Green Threshold
0–255 (128*) Default Blue Threshold

Set the amount of color that the printer detects from the original document.
1–9 (5*) Area Sensitivity
1–9 (5*) E‑mail Bit Depth
1 bit* 8 bit
Set the quality of a JPEG‑format scanned image.
Best for content* 5–95
Specify the contrast of the output.
Best for content* 0 1 2 3 4 5
Adjust the amount of background visible on a scanned image.
Content‑based* Fixed Level
‑4 to 4 (0*)
Create a mirror image of the original document.
Create a negative image of the original document.
Adjust the amount of shadow detail visible on a scanned image.
‑4 to 4 (0*)
Scan Edge to Edge
Allow edge‑to‑edge scanning of the original document.
1–5 (3*) Adjust the sharpness of a scanned image.

Specify whether to generate a cooler or warmer output.
‑4 to 4 (0*)
Specify whether to include blank pages.
Blank Page Removal Blank Page Sensitivity
Max E‑mail Size
0–65535 (0*) Set the allowable file size for each e‑mail.
Size Error Message Specify an error message that the printer sends when an e‑mail exceeds its allowable file size.
Limit Destinations Limit sending of e‑mail only to the specified list of domain names.
Send Me a Copy
Send a copy of the e‑mail to yourself.
Never appears* On by Default Off by Default Always On
Limit E‑mail Recipients
Limit the number of e‑mail recipients.
Enable carbon copy and blind carbon copy in e‑mail.
Use cc:/bcc:
Use Multi‑Page TIFF
Choose between single- and multiple‑page TIFF files.
Set a compression option for TIFF files.
5–95 (75*) Set the quality of text on a scanned image.
5–95 (75*) Set the quality of text or photo on a scanned image.
5–95 (50*) Set the quality of a photo on a scanned image.

Print a log for successful e‑mail transmission.
Print log* Do Not Print Log Print Only For Error
Specify the paper source for printing logs.
Tray [x] (1*) Multipurpose Feeder
Turn on scanning of custom jobs by default.
Show the scan preview on the display.
Allow Save as Shortcut
Save e-mail addresses as shortcuts.
E‑mail Images Sent As
Specify how to send the images in e‑mail.
Reset E-mail Information After Sending
Restore the default e-mail information after sending an e-mail.
Server Set the printer to send e‑mail as a web link.

Specify the file format for the scanned image.
PDF (.pdf)* TIFF (.tif) JPEG (.jpg) XPS (.xps) TXT (.txt) RTF (.rtf) DOCX (.docx)
Configure the settings for optical character recognition (OCR).
Recognized Languages Auto Rotate Despeckle Auto Contrast Enhance
Set the PDF format for the scanned image.
1.3 1.4 1.5* 1.6 1.7 Archival Version
A‑1a* A‑1b Secure
Off* On Archival (PDF/A)
Improve the output result based on the content of the original document.
Text Text/Photo* Graphics Photo

Improve the output result based on the source of the original document.
Black and White Laser Color Laser* Inkjet Photo/Film Magazine Newspaper Press Other
Specify the color when scanning an image.
Black and White Gray Color* Auto
Set the resolution of the scanned image.
75 dpi 150 dpi* 200 dpi 300 dpi 400 dpi 600 dpi
Adjust the darkness of the scanned image.
-4 to 4 (0*)
Specify the orientation of text and graphics on the page.
Set the paper size of the original document.
[List of paper sizes]
Specify the page orientation of text and graphics when scanning a two‑sided document.
Off* Long Edge Short Edge
File Name Specify the file name of the scanned image.

Adjust the amount of toner used for each color in scan output.
-4 to 4 (0*)
Specify which color to drop during scanning, and adjust the dropout setting for that color.
None* Red Green Blue Default Red Threshold
0–255 (128*) Default Green Threshold
0–255 (128*) Default Blue Threshold
Set the amount of color that the printer detects from the original document.
1–9 (5*) Area Sensitivity
Set the quality of a JPEG‑format image.
Best for content* 5–95
Specify the contrast of the output.
Best for content* 0 1 2 3 4 5
Adjust the amount of background visible on a scanned image.
Content‑based* Fixed Level
‑4 to 4 (0*)
Create a mirror image of the original document.

Create a negative image of the original document.
Adjust the amount of shadow detail visible on a scanned image.
‑4 to 4 (0*)
Allow edge‑to‑edge scanning of the original document.
Scan Edge to Edge
1–5 (3*) Adjust the sharpness of a scanned image.
Specify whether to generate a cooler or warmer output.
‑4 to 4 (0*)
Specify whether to include blank pages.
Blank Page Removal Blank Page Sensitivity
5–95 (75*) Set the quality of text on a scanned image.
5–95 (75*) Set the quality of text or photo image on a scanned image.
5–95 (50*) Set the quality of a photo image on a scanned image.
Use Multi‑Page TIFF
Choose between single- and multiple‑page TIFF files.
Set a compression option for TIFF files.
Print a log for successful FTP scan transmission.
Print Log* Do Not Print Log Print Only For Error
Specify the paper source for printing FTP logs.
Tray [x] (1*) Multipurpose Feeder

Enable the Text/Photo mode to have smaller file sizes by using 1‑bit image.
1 bit 8 bit*
Turn on scanning of custom jobs by default.
Show a preview of the scan on the display.
Allow Save as Shortcut
Save custom FTP settings as shortcuts.
Specify the file format for the scanned image.
PDF (.pdf)* TIFF (.tif) JPEG (.jpg) XPS (.xps)
Configure the settings for optical character recognition (OCR).
Recognized Languages Auto Rotate Despeckle Auto Contrast Enhance

Set the PDF format for the scanned image.
1.3 1.4 1.5* 1.6 1.7 Archival Version
A‑1a* A‑1b Secure
Off* On Archival (PDF/A)
Improve the output result based on the content of the original document.
Text Text/Photo* Graphics Photo
Improve the output result based on the source of the original document.
Black and White Laser Color Laser* Inkjet Photo/Film Magazine Newspaper Press Other
Specify the color when scanning an image.
Black and White Gray Color* Auto
Set the resolution of the scanned image.
75 dpi 150 dpi* 200 dpi 300 dpi 400 dpi 600 dpi

1–9 (5*) Adjust the darkness of the scanned image.
Specify the orientation of text and graphics on the page.
Set the paper size of the original document.
[List of paper sizes]
Specify the page orientation of text and graphics when scanning a two‑sided document.
Off* Long edge Short edge
File Name Specify the file name of the scanned image.
Color Balance Adjust the amount of toner used for each color.
Specify which color to drop during scanning, and adjust the dropout setting for that color.
None* Red Green Blue Default Red Threshold
0–255 (128*) Default Green Threshold
0–255 (128*) Default Blue Threshold
Set the amount of color that the printer detects from the original document.
1–9 (5*) Area Sensitivity

Set the quality of a JPEG‑format image.
Best for content* 5–95
Specify the contrast of the output.
Best for content* 0 1 2 3 4 5
Adjust the amount of background visible on a scanned image.
Content‑based* Fixed Level
‑4 to 4 (0*)
Create a mirror image of the original document.
Create a negative image of the original document.
Adjust the amount of shadow detail visible on a scanned image.
‑4 to 4 (0*)
Allow edge‑to‑edge scanning of the original document.
Scan Edge to Edge
1–5 (3*) Adjust the sharpness of a scanned image.
Specify whether to generate a cooler or warmer output.
‑4 to 4 (0*)
Specify whether to include blank pages.
Blank Page Removal Blank Page Sensitivity

5–95 (75*) Set the quality of text on a scanned image.
5–95 (75*) Set the quality of text or photo on a scanned image.
5–95 (75*) Set the quality of a photo on a scanned image.
Use Multi‑Page TIFF
Choose between single- and multiple‑page TIFF files.
Set the compression for TIFF files.
Enable the Text/Photo mode to have smaller file sizes by using 1‑bit image.
1 bit 8 bit*
Turn on scanning of custom jobs by default.
Show a preview of the scan on the display.
1–9999 (1*) Set the number of copies.
Set the paper source for the print job.
Tray [x] (1*) Multipurpose Feeder Manual Paper Manual Envelope
Print the output in color.

Print multiple copies in sequence.
(1,1,1) (2,2,2) (1,2,3) (1,2,3)*
Specify whether to print on one side or two sides of the paper.
1‑Sided* 2‑Sided
Determine which side of the paper (long edge or short edge) is bound when performing two‑sided printing.
Long Edge* Short Edge
Print multiple page images on one side of a sheet of paper.
Off* 2 pages per side 3 pages per side 4 pages per side 6 pages per side 9 pages per side 12 pages per side 16 pages per side
Pages per Side Ordering
Specify the positioning of multiple page images when using Pages per Side.
Horizontal* Reverse Horizontal Reverse Vertical Vertical
Pages per Side Orientation
Specify the orientation of a multiple‑page document when using Pages per Side.
Pages per Side Border
Print a border around each page image when using Pages per Side.
Specify whether to insert blank separator sheets when printing.
Off* Between Copies Between Jobs Between Pages
Specify the paper source for the separator sheet.
Tray [x] (1*) Multipurpose Feeder

Specify whether to print blank pages in a print job.
Do Not Print* Print
Specify how a network is connected.
Auto* Standard Network Wireless
Network Status Show the connection status of the printer network.
Display Network Status on Printer
Show the network status on the display.
Speed, Duplex Show the speed of the currently active network card.
IPv4 Show the IPv4 address.
All IPv6 Addresses Show all IPv6 addresses.
Reset Print Server Reset all active network connections to the printer.
Set the time before the printer cancels a network print job.
Off On* (90 seconds)
Print a banner page.
Scan to PC Port Range
9751:12000* Specify a valid port range for printers that are behind a port blocking firewall.

Setup Using Mobile App Configure the Wi‑Fi connection using Lexmark Mobile Assistant.
Setup On Printer Panel
Configure the Wi‑Fi connection using the control panel.
Choose Network Add Wi‑Fi Network
Network Name Network Mode
Infrastructure Wireless Security Mode
Disabled* WEP WPA2/WPA - Personal WPA2 - Personal 802.1x - RADIUS
Wi‑Fi Protected Setup
Establish a Wi‑Fi network and enable network security.
Start Push Button Method Start PIN Method
Set the network mode.
Enable Wi‑Fi Direct
Enable Wi-Fi Direct‑capable devices to connect directly to the printer.
Specify the standard for the Wi‑Fi network.
802.11b/g/n (2.4GHz)* 802.11a/b/g/n/ac (2.4GHz/5GHz) 802.11a/n/ac (5GHz)
Set the security mode for connecting the printer to Wi‑Fi devices.
Disabled* WEP WPA2/WPA-Personal WPA2-Personal 802.1x - RADIUS
Set the type of Wireless Encryption Protocol (WEP) for the printer.
Set WEP Key Specify a WEP password for secure Wi‑Fi connection.

Enable Wi‑Fi security through Wi-Fi Protected Access (WPA).
Set Pre‑Shared Key Set the password for secure Wi‑Fi connection.
Enable Wi‑Fi security through WPA2.
802.1x Encryption Mode WPA+ WPA2*
Enable Wi‑Fi security through 802.1x standard.
Enable Dynamic Host Configuration Protocol (DHCP) and configure static IP address.
On* Off Set Static IP Address
IP Address Netmask Gateway
Enable and configure IPv6 settings in the printer.
On* Off Enable DHCPv6
On Off* Stateless Address Autoconfiguration
On* Off DNS Server Address Manually Assigned IPv6 Address Manually Assigned IPv6 Router Address Prefix All IPv6 Addresses All IPv6 Router Addresses
View the network addresses.

Set the printer to switch automatically to PCL emulation when a print job requires it, regardless of the default printer language.
Set the printer to switch automatically to PS emulation when a print job requires it, regardless of the default printer language.
Temporarily store print jobs in the printer hard disk before printing.
Set the printer to process Macintosh binary PostScript print jobs.
Network Speed Show the speed of an active network adapter.
Enable Dynamic Host Configuration Protocol (DHCP).
Set the static IP address of your printer.
Set Static IP Address
IP Address Netmask Gateway
Show the printer Media Access Control (MAC) addresses: Locally Administered Address (LAA) and Universally Administered Address (UAA).
Set the printer to switch automatically to PCL emulation when a print job requires it, regardless of the default printer language.

Set the printer to switch automatically to PS emulation when a print job requires it, regardless of the default printer language.
Temporarily store jobs on the printer hard disk before printing.
Set the printer to process Macintosh binary PostScript print jobs.
Reduce power consumption when the printer does not receive data from the Ethernet network.
Set Hostname Set the current TCP/IP host name.
Domain Name Set the domain name.
Allow DHCP/BOOTP to update NTP server
Allow the DHCP and BOOTP clients to update the NTP settings of the printer.
Zero Configuration Name Specify a service name for the zero configuration network.
Assign an IP address automatically.
DNS Server Address Specify the current Domain Name System (DNS) server address.
Backup DNS Server Address Specify the backup DNS server addresses.
Backup DNS Server Address 2
Backup DNS Server Address 3

Domain Search Order Specify a list of domain names to locate the printer and its resources that reside in different domains on the network.
Update the Dynamic DNS settings.
DDNS TTL Specify the current DDNS settings.
Update multicast DNS settings.
WINS Server Address Specify a server address for Windows Internet Name Service (WINS).
Allow the BOOTP to assign a printer IP address.
Restricted Server List Specify an IP address for the TCP connections.
Restricted Server List Options
Specify how the IP addresses in the list can access the printer functionality.
Block All Ports* Block Printing Only Block Printing and HTTP Only
MTU Specify a maximum transmission unit (MTU) parameter for the TCP connections.
1–65535 (9100*) Specify a raw port number for printers connected on a network.
Outbound Traffic Maximum Speed
Enable the printer maximum transfer rate.
Enhance printer privacy and data integrity.

SNMP Versions 1 and 2c
Configure Simple Network Management Protocol (SNMP) versions 1 and 2c to install print drivers and applications.
Off On* Allow SNMP Set
Off On* Enable PPM MIB
Off On* SNMP Community
Configure SNMP version 3 to install and update the printer security.
Off On* Set Read/Write Credentials
User Name Password Set Read‑only Credentials
User Name Password Authentication Hash
MD5 SHA1* Minimum Authentication Level
No Authentication, No Privacy Authentication, No Privacy Authentication, Privacy* Privacy Algorithm
Enable Internet Protocol Security (IPSec).

Set the IPSec base configuration.
IPSec Device Certificate Specify an IPSec certificate.
Pre‑Shared Key Authenticated Connections
Configure the authenticated connections of the printer.
Let the printer join networks that require authentication before allowing access.
0–65535 seconds (90*) Set the time‑out value to stop the Line Printer Daemon (LPD) server from waiting indefinitely for hung or invalid print jobs.
Print a banner page for all LPD print jobs.

Print a trailer page for all LPD print jobs.
LPD Carriage Return Conversion
Enable carriage return conversion.
Access the Embedded Web Server to monitor and manage the printer.
Configure the Hypertext Transfer Protocol Secure (HTTPS) settings.
Send files using FTP.
Local Domains Specify domain names for HTTP and FTP servers.
HTTP Proxy IP Address Configure the HTTP and FTP server settings.
HTTP Default IP Port
FTP Default IP Port
Timeout for HTTP/FTP Requests
Specify the amount of time before the server connection stops.
Retries for HTTP/FTP Requests
1–299 (3*) Set the number of retries to connect to the HTTP/FTP server.

Print using ThinPrint.
4000–4999 (4000*) Set the port number for the ThinPrint server.
100–1000000 (0*) Set the speed to transmit data in a ThinPrint environment.
0–64000 (0*) Set the packet size for data transmission.
Set the printer to switch to PCL emulation when a print job received through a USB port requires it, regardless of the default printer language.
Set the printer to switch to PS emulation when a print job received through a USB port requires it, regardless of the default printer language.
Temporarily store jobs on the printer hard disk before printing.
Set the printer to process Macintosh binary PostScript print jobs.
Enable the standard USB port.

Register the printer to the Google Cloud Print server.
Print directly from your Google account.
Enable Google Cloud Print
Allow the registered user and other users on the same subnet to send jobs to the printer locally.
Verify authenticity of the peer certificate to connect to your Google account.
Enable SSL Peer Verification
Set the printer to process PDF files as an image for faster printing.
Always Print As Image
SSID Specify the service set identifier (SSID) of the Wi‑Fi network.
Set Preshared Key Set the preshared key (PSK) to authenticate and validate users on a Wi‑Fi connection.
Show PSK on Setup Page
Show the PSK on the Network Setup Page.
Group Owner IP Address Specify the IP address of the group owner.
Auto‑Accept Push Button Requests
Accept requests to connect to the network automatically.

Control access to the printer functions.
Access Address Book in Apps Modify Address Book Manage Shortcuts Create Profiles Manage Bookmarks Flash Drive Print Flash Drive Color Printing Flash Drive Scan Copy Function Copy Color Printing Color Dropout E‑mail Function Fax Function FTP Function Release Held Faxes Held Jobs Access User Profiles Cancel Jobs at the Device Change Language Internet Printing Protocol (IPP) Initiate Scans Remotely B/W Print Color Print
Control access to the printer menu settings.
Security Menu Network/Ports Menu Paper Menu Reports Menu Function Configuration Menus Supplies Menu Option Card Menu SE Menu Device Menu
Menu item Description · Function Access · Administrative Menus

Control access to the printer management options.
Remote Management Firmware Updates Apps Configuration Operator Panel Lock Import/Export All Settings Out of Service Erase
Control access to printer applications.
New Apps Card Copy Scan Center Scan Center Custom 1 Scan Center Custom 2 Scan Center Custom 3 Scan Center Custom 4 Scan Center Custom 5 Scan Center Custom 6 Scan Center Custom 7 Scan Center Custom 8 Scan Center Custom 9 Scan Center Custom 10 Forms and Favorites
Control group or user access to the printer functions, applications, and security settings.
Function Access Administrative Menus Device Management Apps All Users
Function Access Administrative Menus Device Management Apps Admin

Create local accounts to manage access to the printer functions.
User Name/Password User Name Password PIN
Schedule access to the USB ports.
Record the events in the secure audit log and remote syslog.
Send audit logs to a remote server.
Remote Syslog Server Specify the remote syslog server.
1–65535 (514*) Specify the remote syslog port.
Specify a syslog method to transmit logged events to a remote server.

Specify a facility code that the printer uses when sending log events to a remote server.
0 ‑ Kernel Messages 1 ‑ User‑Level Messages 2 ‑ Mail System 3 ‑ System Daemons 4 ‑ Security/Authorization Messages* 5 ‑ Messages Generated Internally by Syslogs 6 ‑ Line Printer Subsystem 7 ‑ Network News Subsystem 8 ‑ UUCP Subsystem 9 ‑ Clock Daemon 10 ‑ Security/Authorization Messages 11 ‑ FTP Daemon 12 ‑ NTP Subsystem 13 ‑ Log Audit 14 ‑ Log Alert 15 ‑ Clock Daemon 16 ‑ Local Use 0 (local0) 17‑ Local Use 1 (local1) 18 ‑ Local Use 2 (local2) 19 ‑ Local Use 3 (local3) 20 ‑ Local Use 4 (local4) 21 ‑ Local Use 5 (local5) 22 ‑ Local Use 6 (local6) 23 ‑ Local Use 7 (local7)
Severity of Events to Log
Specify the priority level cutoff for logging messages and events.
0 ‑ Emergency 1 ‑ Alert 2 ‑ Critical 3 ‑ Error 4 ‑ Warning* 5 ‑ Notice 6 ‑ Informational 7 ‑ Debug
Remote Syslog Non‑Logged Events
Send all events, regardless of severity level, to the remote server.
Admin’s E‑mail Address Send e‑mail notification of logged events to the administrator.
Menu item Description · Remote Syslog Facility · Off* On

E‑mail Log Cleared Alert
Send e‑mail notification to the administrator when a log entry is deleted.
E‑mail Log Wrapped Alert
Send e‑mail notification to the administrator when the log becomes full and begins to overwrite the oldest entries.
Resolve log storage issues when the log fills its allotted memory.
Wrap Over Older Entries* E‑mail Log Then Delete All Entries
E‑mail % Full Alert
Send e‑mail notification to the administrator when the log fills its allotted memory.
% Full Alert Level
E‑mail Log Exported Alert
Send e‑mail notification to the administrator when a log is exported.
E‑mail Log Settings Changed Alert
Send e‑mail notification to the administrator when Enable Audit is set.
Specify how the log file terminates the end of each line.
LF (\n)* CR (\r) CRLF (\r\n)
Add a digital signature to each exported log file.
Clear Log Delete all audit logs.
Export a security log to a flash drive.
Syslog (RFC 5424) Syslog (RFC 3164) CSV

1–10 (3*) Specify the number of failed login attempts before the user gets locked out.
1–60 minutes (5*) Specify the time frame between failed login attempts before the user gets locked out.
1–60 minutes (5*) Specify the lockout duration.
1–120 minutes (10*) Specify the delay for a remote login before the user is logged off automatically.
2–10 Set the number of times an invalid PIN can be entered.
Set the expiration time for confidential print jobs.
Off* 1 Hour 4 Hours 24 Hours 1 Week
Set the expiration time for a print job that you want to repeat.
Off* 1 Hour 4 Hours 24 Hours 1 Week
Set the expiration time that the printer prints a copy for the user to examine its quality, before printing the remaining copies.
Off* 1 Hour 4 Hours 24 Hours 1 Week

Set the expiration time that the printer stores print jobs for printing later.
Off* 1 Hour 4 Hours 24 Hours 1 Week
Require All Jobs to be Held
Set the printer to hold all print jobs.
Set the printer to print other documents with the same file name without overwriting any of the print jobs.
Determine whether Disk Encryption is enabled.
Start encryption Prevent the loss of sensitive data in case the printer or its hard disk is stolen.
Stored in onboard memory
Delete all files stored on the printer memory.
Stored on hard disk
Delete all files stored on the printer hard disk.
1 Pass Erase* 3 Pass Erase 7 Pass Erase

Search the different servers in the domain for the logged-in user account.
Enable verification of LDAP certificates.
Enable functions in the AirPrint software feature.
Show all the features that Function Access Control (FAC) protects regardless of the security permission that the user has.
Let the user log in before printing.
Default Print Permission Login Set the default login for Print Permission.
Specify the effect of using the security reset jumper.
Enable “Guest” access* No Effect
0–32 (0*) Specify the minimum characters that are allowed for a password.

Menu Settings Page Print a report that contains the printer preferences, settings, and configurations.
Device Information Print a report that contains information about the printer.
Device Statistics Print a report about printer usage and supply status.
Profile List Print a list of profiles that are stored in the printer.
Asset Report Print a report that contains the printer serial number and model name.
Print samples and information about the fonts that are available in each printer language.
PCL Fonts PS Fonts
Print Directory Print the resources that are stored in the flash drive or printer hard disk.
All Shortcuts Print a report that lists the shortcuts that are stored in the printer.
E‑mail Shortcuts
Fax Job Log Print a report about the last 200 completed fax jobs.

Fax Call Log Print a report about the last 100 attempted, received, and blocked calls.
Network Setup Page Print a page that shows the configured network and wireless settings on the printer.
Print All Guides Prints all the guides
Color Quality Guide Provides information about solving color quality issues
Connection Guide Provides information about connecting the printer locally (USB) or to a network
Copy Guide Provides information about making a copy and configuring the settings
E‑mail Guide Provides information about sending an e‑mail and configuring the settings
Fax Guide Provides information about sending a fax and configuring the settings
Scan Guide Provides information about scanning a document and configuring the settings
Information Guide Provides information about the printer
Media Guide Provides information about loading paper and specialty media
Moving Guide Provides information about moving, locating, or shipping the printer
Print Quality Guide Provides information about solving print quality issues
Supplies Guide Provides information about ordering supplies
Print Quality Test Pages Print sample pages to identify and correct print quality defects.
Cleaning the Scanner Print instructions on how to clean the scanner.

From the control panel, navigate to:
Settings > Reports > Menu Settings Page
For non‑touch‑screen printer models, press to navigate through the settings.

Securing the printer 147
The printer is equipped with a security lock feature. Attach a security lock compatible with most laptop computers in the location shown to secure the printer in place.

To erase volatile memory or buffered data in your printer, turn off the printer.
To erase non‑volatile memory or individual settings, device and network settings, security settings, and embedded solutions, do the following:
1 From the control panel, navigate to:
Settings > Device > Maintenance > Out of Service Erase > Sanitize all information on nonvolatile memory
For non-touch-screen printer models, press to navigate through the settings.
2 Depending on your printer model, select ERASE or Continue.
3 Follow the instructions on the display.
1 From the home screen, touch Settings > Device > Maintenance > Out of Service Erase.
2 Select the Sanitize all information on hard disk check box, and then touch ERASE.

Securing the printer 148
3 Follow the instructions on the display.
This process erases all contents in the hard disk. If necessary, back up important data from the printer before starting the encryption.
1 From the home screen, touch Settings > Security > Disk Encryption > Start encryption.
2 Follow the instructions on the display.
1 From the control panel, navigate to:
Settings > Device > Restore Factory Defaults
For non-touch-screen printer models, press to navigate through the settings.
2 In the Restore Settings menu, select the settings that you want to restore.
3 Select RESTORE.
4 Follow the instructions on the display.
Type of memory Description
Volatile memory The printer uses standard random access memory (RAM) to buffer temporarily user data during simple print and copy jobs.
Non-volatile memory The printer may use two forms of non-volatile memory: EEPROM and NAND (flash memory). Both types are used to store the operating system, printer settings, network information, scanner and bookmark settings, and embedded solutions.
Hard disk memory Some printers may have a hard disk drive installed. The printer hard disk is designed for printer-specific functionality. The hard disk lets the printer retain buffered user data from complex print jobs, form data, and font data.

Securing the printer 149
Erase the content of any installed printer memory in the following circumstances:

Maintaining the printer 150
1 From the control panel, touch Settings > Device > Preferences > Audio Feedback.
2 Adjust the volume.
1 From the control panel, navigate to:
Settings > Device > Accessibility
2 Adjust Headphone Volume.
1 From the control panel, navigate to:
Settings > Fax > Analog Fax Setup > Speaker Settings
For non-touch-screen printer models, press to navigate through the settings.

Maintaining the printer 151
1 From the home screen, navigate to:
Settings > Network/Ports > Wireless
For non-touch-screen printer models, press to navigate through the settings.
2 Select Setup On Printer Panel, and then follow the instructions on the display.
1 Depending on your mobile device, download the Lexmark Mobile Assistant application from either the Google PlayTM store or App Store online store.
2 From the control panel, navigate to:
Settings > Network/Ports > Wireless > Setup Using Mobile App > Continue for Printer ID
For non-touch-screen printer models, press to navigate through the settings.
3 From your mobile device, launch the application, and then accept the Terms of Use.
4 Grant permissions.
5 Tap Start Wi-Fi Setup, and then select the printer.
6 Select a Wi-Fi network, and then enter your credentials.
7 Tap Finish Wi-Fi Setup.
Connecting the printer to a wireless network using Wi‑Fi Protected Setup (WPS)
Before you begin, make sure that:
1 From the control panel, navigate to:
Settings > Network/Ports > Wireless > Wi‑Fi Protected Setup > Start Push Button Method
For non-touch-screen printer models, press to navigate through the settings.
2 Follow the instructions on the display.

Maintaining the printer 152
1 From the control panel, navigate to:
Settings > Network/Ports > Wireless > Wi‑Fi Protected Setup > Start PIN Method
For non-touch-screen printer models, press to navigate through the settings.
2 Copy the eight‑digit WPS PIN.
3 Open a Web browser, and then type the IP address of your access point in the address field.
4 Access the WPS settings. For more information, see the documentation that came with your access point.
5 Enter the eight‑digit PIN, and then save the changes.
1 From the printer control panel, navigate to:
Settings > Network/Ports > Network Overview > Active Adapter > Standard Networking
For non-touch-screen printer models, press to navigate through the settings.
2 Follow the instructions on the display.
1 Open the printers folder.
2 From the shortcut menu of the printer with the new ISP, open the printer properties.
3 Configure the port from the list.
4 Update the IP address.
5 Apply the changes.

Maintaining the printer 153
1 From System Preferences in the Apple menu, navigate to the list of printers, and then select + > IP.
2 Type the IP address in the address field.
3 Apply the changes.
1 Turn off the printer, and then unplug the power cord from the electrical outlet.
2 Remove paper from the standard bin and multipurpose feeder.
3 Remove any dust, lint, and pieces of paper around the printer using a soft brush or vacuum.
4 Wipe the outside of the printer with a damp, soft, lint‑free cloth.
5 Connect the power cord to the electrical outlet, and then turn on the printer.

Maintaining the printer 154
1 Open the scanner cover.

2 Using a damp, soft, lint-free cloth, wipe the following areas: • ADF glass



Maintaining the printer 155


3 Close the scanner cover.
If your printer has another ADF glass inside door C, then continue with the following steps.
4 Open door C.


Maintaining the printer 156
5 Using a damp, soft, lint-free cloth, wipe the following areas: • ADF glass pad in door C


6 Close the door.
To order parts and supplies in the U.S., contact 1-800-539-6275 for information about Lexmark authorized dealers in your area. In other countries or regions, go to www.lexmark.com or contact the place where you purchased the printer.
1 From the control panel, navigate to:
Settings > Reports > Device > Device Statistics
For non‑touch‑screen printer models, press to navigate through the settings.
2 From the Supply Information section of the pages printed, check the status of parts and supplies.

Maintaining the printer 157
Your Lexmark printer is designed to function best with genuine Lexmark parts and supplies. Use of third-party supplies or parts may affect the performance, reliability, or life of the printer and its imaging components. It can also affect warranty coverage. Damage caused by the use of third-party parts and supplies is not covered by the warranty. All life indicators are designed to function with Lexmark parts and supplies, and may deliver unpredictable results if third-party parts and supplies are used. Imaging component usage beyond the intended life may damage your Lexmark printer or its associated components.

1 Supported only in the CX421, CX522, CX622, and CX625 printer models.
2 Supported only in the CX622 and CX625 printer models.
For more information on countries located in each region, go to www.lexmark.com/regions.

Maintaining the printer 158

1 Supported only in the CX421, CX522, CX622, and CX625 printer models.
2 Supported only in the CX622 and CX625 printer models.
For more information on countries located in each region, go to www.lexmark.com/regions.

1 Supported only in the CX421 and CX522 printer models.
2 Supported only in the CX622 and CX625 printer models.

1 Supported only in the MC2425, MC2535, and MC2640 printer models.
2 Supported only in the MC2535 and MC2640 printer models.
For more information on countries located in each region, go to www.lexmark.com/regions.

Maintaining the printer 159

1 Supported only in the MC2425, MC2535, and MC2640 printer models.
2 Supported only in the MC2535 and MC2640 printer models.
For more information on countries located in each region, go to www.lexmark.com/regions.

2 Supported only in the MC2425, MC2535, and MC2640 printer models.
4 Supported only in MC2535 and MC2640 printer models.

Maintaining the printer 160

2 Supported only in the MC2425, MC2535, and MC2640 printer models.
4 Supported only in MC2535 and MC2640 printer models.



Waste toner bottle 78C0W00
Item Part number

Maintaining the printer 161
Match the maintenance kit to the printer voltage.
100 V fuser maintenance kit 41X2095
110 V fuser maintenance kit 41X2096
220 V fuser maintenance kit 41X2097
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Settings > Device > Notifications.
3 From the Supplies menu, click Custom Supply Notifications.
4 Select a notification for each supply item.
5 Apply the changes.
1 Open door B until it clicks into place.
Item Part number

Maintaining the printer 162

2 Remove the used toner cartridge.

3 Unpack the new toner cartridge.

Maintaining the printer 163
4 Insert the new toner cartridge.

5 Close door B.

1 Open door B until it clicks into place.

Maintaining the printer 164
2 Open door A.


Maintaining the printer 165
3 Remove the right side cover.

4 Remove the used waste toner bottle.

5 Unpack the new waste toner bottle.

Maintaining the printer 166
6 Insert the new waste toner bottle.

7 Insert the right side cover.


Maintaining the printer 167
8 Close door B.

9 Close door A.
1 Open door B until it clicks into place.
2 Open door A.

Maintaining the printer 168
3 Remove the right side cover.

Maintaining the printer 169
4 Remove the waste toner bottle.

5 Remove the toner cartridges.


Maintaining the printer 170
6 Remove the used imaging kit.

7 Unpack the new imaging kit.
Black imaging kit Black and color imaging kit



Maintaining the printer 171
8 Remove the packing material.



Maintaining the printer 172
9 Insert the imaging kit until it is fully seated.

10 Insert the toner cartridges.


Maintaining the printer 173
11 Insert the waste toner bottle.
12 Insert the right side cover.

Maintaining the printer 174
13 Close door B.
14 Close door A.

Maintaining the printer 175
For shipping instructions, go to http://support.lexmark.com or contact customer support.
For non-touch-screen printer models, press to navigate through the settings.
1 From the control panel, navigate to:
Settings > Device > Power Management > Eco‑Mode
2 Select a setting.
1 From the control panel, navigate to:
Settings > Device > Power Management > Timeouts > Sleep Mode
2 Specify the amount of time that the printer stays idle before it enters Sleep mode.
1 From the control panel, navigate to:
Settings > Device > Power Management > Timeouts > Hibernate Timeout
2 Select the amount of time that the printer stays idle before it enters Hibernate mode.
Eco‑Mode

Maintaining the printer 176
1 From the control panel, navigate to:
Settings > Device > Preferences
For non-touch-screen printer models, press to navigate through the settings.
2 In the Screen Brightness menu, adjust the setting.
To return Lexmark products for recycling:
1 Go to www.lexmark.com/recycle.
2 Select the product you want to recycle.
Lexmark continually strives to minimize packaging. Less packaging helps to ensure that Lexmark printers are transported in the most efficient and environmentally sensitive manner and that there is less packaging to dispose of. These efficiencies result in fewer greenhouse emissions, energy savings, and natural resource savings. Lexmark also offers recycling of packaging components in some countries or regions. For more information, go to www.lexmark.com/recycle, and then choose your country or region. Information on available packaging recycling programs is included with the information on product recycling.
Lexmark cartons are 100% recyclable where corrugated recycling facilities exist. Facilities may not exist in your area.
The foam used in Lexmark packaging is recyclable where foam recycling facilities exist. Facilities may not exist in your area.
When you return a cartridge to Lexmark, you can reuse the box that the cartridge came in. Lexmark recycles the box.

Maintaining the printer 177
The Lexmark Cartridge Collection Program allows you to return used cartridges for free to Lexmark for reuse or recycling. One hundred percent of the empty cartridges returned to Lexmark are either reused or demanufactured for recycling. The boxes used to return the cartridges are also recycled.
To return Lexmark cartridges for reuse or recycling, do the following:
1 Go to www.lexmark.com/recycle.
2 Select the product that you want to recycle.

Avoiding jams
Correct loading of paper Incorrect loading of paper



Clearing jams 178


1 Automatic document feeder (ADF)

1 Remove the tray.

2 Remove the jammed paper.

3 Insert the tray.
1 Open door A, and then open door B until it clicks into place.
Clearing jams 180


2 Remove the jammed paper.
Clearing jams 181


3 Close doors B and A.
1 Open doors A and B.
Clearing jams 182


2 Open the fuser access door, and then remove the jammed paper.
Clearing jams 183


3 Close doors B and A.
1 Open door A.
Clearing jams 184


2 Remove the jammed paper.

3 Close door A.
1 Open door B until it clicks into place, and then remove the jammed paper.
Clearing jams 185


2 Open door A.
Clearing jams 186

3 Open the fuser access door, and then remove the jammed paper.
Clearing jams 187


4 Close doors A and B.
Clearing jams 188

1 Remove paper from the multipurpose feeder.

2 Remove the jammed paper.
3 Flex, fan, and align the paper edges before loading.
4 Reload paper.

Clearing jams 189

1 Remove the tray.

2 Remove the jammed paper.

3 Insert the tray.
1 Remove all original documents from the ADF tray.
2 Open door C.
Clearing jams 190


3 Remove the jammed paper.

4 Close door C.
Clearing jams 191

Network connection problems
Step 1 Check if the printer is on.
Go to step 2. Turn on the printer.
Is the printer on?
Go to step 3. Type the correct printer IP address in the address field.
Make sure that the printer IP address is correct.
View the printer IP address:
Is the printer IP address correct?
Go to step 4. Install a supported browser.
Check if you are using a supported browser:
Is your browser supported?
Step 4 Check if the network connection is working.
Go to step 5. Contact your administrator.
Is the network connection working?
Go to step 6. Secure the cable connections.
Make sure that the cable connections to the printer and print server are secure. For more information, see the documentation that came with the printer.
Are the cable connections secure?

Go to step 7. Contact your administrator.
Check if the web proxy servers are disabled.
Are the web proxy servers disabled?
Step 7 Access the Embedded Web Server.
The problem is solved.
Contact customer support.
Did the Embedded Web Server open?
Go to step 2. Wait for the printer to finish processing the other job.
Check if the printer is not busy processing another print, copy, scan, or fax job.
Is the printer ready?
Go to step 3. Insert the flash drive into the correct port.
Check if the flash drive is inserted into the front USB port.
Is the flash drive inserted into the correct port?
Go to step 4. Insert a supported flash drive.
Check if the flash drive is supported. For more information, see “Supported flash drives and file types” on page 43.
Is the flash drive supported?
The problem is solved.
Contact customer support.
a Check if the USB port is enabled. For more information, see
“Enabling the USB port” on page 193. b Remove, and then insert the flash drive.
Does the printer recognize the flash drive?
From the control panel, navigate to:
Settings > Network/Ports > USB > Enable USB Port
For non-touch-screen printer models, press to navigate through the settings.

1 Print the Network Setup Page.
From the control panel, navigate to:
Settings > Reports > Network > Network Setup Page
For non-touch-screen printer models, press to navigate through the settings.
2 Check the first section of the page and confirm that the status is connected.
If the status is not connected, then the LAN drop may be inactive or the network cable may be unplugged or malfunctioning. Contact your administrator for assistance.
The problem is solved.
Go to step 2.
Turn off the printer, wait for about 10 seconds, and then turn on the printer.
Does the internal option operate correctly?
Go to step 4. Go to step 3.
Print the Menu Settings Page, and then check if the internal option appears in the Installed Features list.
Is the internal option listed in the menu settings page?
The problem is solved.
Go to step 4.
Check if the internal option is installed properly into the controller board.
a Turn off the printer, and then unplug the power cord from the
electrical outlet. b Make sure that the internal option is installed in the appropriate
connector in the controller board. c Connect the power cord to the electrical outlet, and then turn
on the printer.
Does the internal option operate correctly?

The problem is solved.
Contact customer support.
a Check if the internal option is available in the print driver.
Does the internal option operate correctly?
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
To correct this problem, purchase a cartridge with the correct region that matches the printer region, or purchase a worldwide cartridge.
Troubleshooting 195 · Action Yes No · Step 4

Worldwide or Undefined region 0
North America (United States, Canada) 1
European Economic Area, Western Europe, Nordic countries, Switzerland 2
Rest of Europe, Middle East, Africa 5
Australia, New Zealand 6
The printer has detected a non‑Lexmark supply or part installed in the printer.
Your Lexmark printer is designed to function best with genuine Lexmark supplies and parts. Use of third- party supplies or parts may affect the performance, reliability, or life of the printer and its imaging components.
All life indicators are designed to function with Lexmark supplies and parts and may deliver unpredictable results if third-party supplies or parts are used. Imaging component usage beyond the intended life may damage your Lexmark printer or associated components.
To accept any and all of these risks and to proceed with the use of non-genuine supplies or parts in your printer, from the control panel, press and hold X and # simultaneously for 15 seconds.
If you do not want to accept these risks, then remove the third-party supply or part from your printer and install a genuine Lexmark supply or part. For more information, see “Using genuine Lexmark parts and supplies” on page 157.
If the printer does not print after pressing and holding X and # simultaneously for 15 seconds, then reset the supply usage counter.
1 From the control panel, navigate to:
Settings > Device > Maintenance > Configuration Menu > Supply Usage And Counters
2 Select the part or supply that you want to reset, and then select Start.
3 Read the warning message, and then select Continue.
4 Press and hold X and # simultaneously for 15 seconds to clear the message.

The printer is scheduled for maintenance. For more information, go to http://support.lexmark.com or contact your service representative, and then report the message.
Go to step 2. The problem is solved.
a Use an envelope that has been stored in a dry environment.
Does the envelope seal when printing?
Contact customer support.
The problem is solved.
a Make sure that paper type is set to Envelope.
From the control panel, navigate to: Settings > Paper > Tray Configuration > Paper Size/Type
For non‑touch‑screen printer models, press to navigate through the settings. b Send the print job.
Does the envelope seal when printing?
The problem is solved.
Go to step 2.
a From the printer control panel, navigate to:
Settings > Print > Layout > Collate
For non-touch-screen printer models, press to navigate through the settings. b Set Collate to On.
c Print the document.
Are the pages collated correctly?

The problem is solved.
Go to step 3.
a From the document that you are trying to print, open the Print
dialog, and then select Collate. b Print the document.
Are the pages collated correctly?
The problem is solved.
Contact customer support.
a Reduce the number of pages to print. b Print the document.
Are the pages collated correctly?
The problem is solved.
Go to step 2.
a Check if the trays contain the same paper size and paper type. b Check if the paper guides are positioned correctly.
c Print the document.
Do the trays link correctly?
The problem is solved.
Go to step 3.
a From the control panel, navigate to:
Settings > Paper > Tray Configuration > Paper Size/Type
For non-touch-screen printer models, press to navigate through the settings. b Set the paper size and paper type to match the paper loaded
in the linked trays. c Print the document.
Do the trays link correctly?
The problem is solved.
Contact customer support.
a Make sure that Tray Linking is set to Automatic. For more
information, see “Linking trays” on page 34. b Print the document.
Do the trays link correctly?

Go to step 2. The problem is solved.
a Remove the tray. b Check if paper is loaded correctly.
Do paper jams occur frequently?
Go to step 3. The problem is solved.
a From the control panel, navigate to:
Settings > Paper > Tray Configuration > Paper Size/Type
For non‑touch‑screen printer models, press to navigate through the settings. b Set the correct paper size and type.
c Print the document.
Do paper jams occur frequently?
Contact customer support.
The problem is solved.
a Load paper from a fresh package.
Do paper jams occur frequently?

a From the control panel, navigate to:
The problem is solved.
Contact customer support.
Settings > Device > Notifications > Jam Content Recovery
For non-touch-screen printer models, press to navigate through the settings. b Select On or Auto, and then apply the changes.
c Print the document.
Are the jammed pages reprinted?

Settings > Troubleshooting > Print Quality Test Pages. For non-touch-screen printer models, press to navigate through the settings.
a Remove, and then insert the imaging kit.
Contact customer support.
The problem is solved.
Is the printer printing blank or white pages?
Troubleshooting 200 · Action Yes No · Action Yes No


Settings > Troubleshooting > Print Quality Test Pages. For non-touch-screen printer models, press to navigate through the settings.
Go to step 2. The problem is solved.
a Perform Color Adjust.
From the control panel, navigate to:
Settings > Print > Quality > Advanced Imaging > Color Adjust b Print the document.
Is the print too dark?
Go to step 3. The problem is solved.
a Depending on your operating system, reduce toner darkness
from the Printing Preferences or Print dialog.
Settings > Print > Quality > Toner Darkness b Print the document.
Is the print too dark?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type
from the Printing Preferences or Print dialog.
Is the print too dark?

Go to step 5. Go to step 6.
Check if the paper has texture or rough finishes.
Are you printing on textured or rough paper?
Go to step 6. The problem is solved.
a Replace textured or rough paper with plain paper. b Print the document.
Is the print too dark?
Contact customer support.
The problem is solved.
a Load paper from a fresh package.
Is the print too dark?

Settings > Troubleshooting > Print Quality Test Pages. For non-touch-screen printer models, press to navigate through the settings.
Go to step 2. The problem is solved.
a Load the tray with the correct paper type. b Print the document.
Do ghost images appear on prints?

Go to step 3. The problem is solved.
a Depending on your operating system, specify the paper type
from the Printing Preferences or Print dialog.
Settings > Paper > Tray Configuration > Paper Size/Type b Print the document.
Do ghost images appear on prints?
Go to step 4. The problem is solved.
a Perform Color Adjust.
From the control panel, navigate to: Settings > Print > Quality > Advanced Imaging > Color Adjust b Print the document.
Do ghost images appear on prints?
Contact customer support.
The problem is solved.
a Remove, and then insert the imaging kit.
Do ghost images appear on prints?

Settings > Troubleshooting > Print Quality Test Pages. For non-touch-screen printer models, press to navigate through the settings.

Go to step 2. The problem is solved.
a Perform Color Adjust.
From the control panel, navigate to:
Settings > Print > Quality > Advanced Imaging > Color Adjust b Print the document.
Does gray or colored background appear on prints?
Contact customer support.
The problem is solved.
a Remove, and then insert the imaging kit.
Does gray or colored background appear on prints?

The problem is solved.
Go to step 2.
a Adjust the paper guides to the correct position for the paper
loaded. b Print the document.
Are the margins correct?
The problem is solved.
Go to step 3.
a Set the paper size from the control panel. Navigate to:
Settings > Paper > Tray Configuration > Paper Size/Type b Print the document.
Are the margins correct?

The problem is solved.
Contact customer support.
a Depending on your operating system, specify the paper size
from the Printing Preferences or Print dialog.
Are the margins correct?

Settings > Troubleshooting > Print Quality Test Pages. For non-touch-screen printer models, press to navigate through the settings.
Go to step 2. The problem is solved.
a Perform Color Adjust.
From the control panel, navigate to:
Settings > Print > Quality > Advanced Imaging > Color Adjust b Print the document.
Is the print light?
Go to step 3. The problem is solved.
a Depending on your operating system, increase toner darkness
from the Printing Preferences or Print dialog.
Settings > Print > Quality > Toner Darkness b Print the document.
Is the print light?

Go to step 4. The problem is solved.
a Turn off Color Saver.
From the control panel, navigate to: Settings > Print > Quality > Color Saver b Print the document.
Is the print light?
Go to step 5. The problem is solved.
a Depending on your operating system, specify the paper type
from the Printing Preferences or Print dialog.
Settings > Paper > Tray Configuration > Paper Size/Type b Print the document.
Is the print light?
Step 5 Check if paper has texture or rough finishes.
Go to step 6. Go to step 7.
Are you printing on textured or rough paper?
Go to step 7. The problem is solved.
a Replace textured or rough paper with plain paper. b Print the document.
Is the print light?
Go to step 8. The problem is solved.
a Load paper from a fresh package.
Is the print light?

Contact customer support.
The problem is solved.
a Remove, and then insert the imaging kit.
Is the print light?

Settings > Troubleshooting > Print Quality Test Pages. For non-touch-screen printer models, press to navigate through the settings.
a Remove the toner cartridge of the missing color. b Remove the imaging kit.
Contact customer support.
The problem is solved.
f Print the document.
Are some colors missing on prints?


Settings > Troubleshooting > Print Quality Test Pages. For non-touch-screen printer models, press to navigate through the settings.
Go to step 2. Contact customer support.
Check the printer for leaked toner contamination.
Is the printer free of leaked toner?
Go to step 4. Go to step 3.
a From the control panel, navigate to:
Settings > Paper > Tray Configuration > Paper Size/Type b Check if the paper size and paper type settings match the
paper loaded.
Do the settings match?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper size
and paper type from the Printing Preferences or Print dialog.
Is the print mottled?
Go to step 5. The problem is solved.
a Load paper from a fresh package.
Is the print mottled?

Contact customer support.
The problem is solved.
a Remove, and then insert the imaging kit.
Is the print mottled?

Go to step 2. The problem is solved.
a Adjust the guides in the tray to the correct position for the paper
loaded. b Print the document.
Is the paper curled?
Go to step 3. The problem is solved.
a Depending on your operating system, specify the paper type
from the Printing Preferences or Print dialog.
Settings > Paper > Tray Configuration > Paper Size/Type b Print the document.
Is the paper curled?

Go to step 4. The problem is solved.
Print on the other side of the paper.
a Remove paper, flip it over, and then reload paper. b Print the document.
Is the paper curled?
Contact customer support.
The problem is solved.
a Load paper from a fresh package.
Is the paper curled?

Settings > Troubleshooting > Print Quality Test Pages. For non-touch-screen printer models, press to navigate through the settings.
Go to step 2. The problem is solved.
a Adjust the paper guides in the tray to the correct position for
the paper loaded. b Print the document.
Is the print crooked or skewed?
Go to step 3. The problem is solved.
a Load paper from a fresh package.
Is the print crooked or skewed?

Contact customer support.
The problem is solved.
a Check if the paper loaded is supported.
Is the print crooked or skewed?

Settings > Troubleshooting > Print Quality Test Pages. For non-touch-screen printer models, press to navigate through the settings.
a Remove, and then reinstall the imaging kit.
Contact customer support.
The problem is solved.
Is the printer printing solid color or black images?


Settings > Troubleshooting > Print Quality Test Pages. For non-touch-screen printer models, press to navigate through the settings.
Go to step 2. The problem is solved.
a Adjust the paper guides in the tray to the correct position for
the paper loaded. b Print the document.
Are text or images cut off?
Go to step 3. The problem is solved.
a Depending on your operating system, specify the paper size
from the Printing Preferences or Print dialog.
Settings > Paper > Tray Configuration > Paper Size/Type b Print the document.
Are text or images cut off?
Contact customer support.
The problem is solved.
a Remove, and then insert the imaging kit.
Are text or images cut off?


Settings > Troubleshooting > Print Quality Test Pages. For non-touch-screen printer models, press to navigate through the settings.
Go to step 2. The problem is solved.
a Depending on your operating system, specify the paper type
from the Printing Preferences or Print dialog.
Settings > Paper > Tray Configuration > Paper Size/Type b Print the document.
Does toner easily rub off?
Go to step 3. The problem is solved.
a Check if the paper weight is supported.
Does toner easily rub off?
Contact customer support.
The problem is solved.
a Load paper from a fresh package.
Does toner easily rub off?

Settings > Troubleshooting > Print Quality Test Pages. For non-touch-screen printer models, press to navigate through the settings.

a Remove, and then insert the imaging kit.
Contact customer support.
The problem is solved.
Is the print density uneven?

Settings > Troubleshooting > Print Quality Test Pages. For non-touch-screen printer models, press to navigate through the settings. • If horizontal dark lines keep appearing on the prints, then see the “Repeating defects” topic.
Go to step 2. The problem is solved.
a Depending on your operating system, specify the paper type
from the Printing Preferences or Print dialog.
Settings > Paper > Tray Configuration > Paper Size/Type b Print the document.
Do dark lines appear on prints?

Go to step 3. The problem is solved.
a Load paper from a fresh package.
Do dark lines appear on prints?
Contact customer support.
The problem is solved.
a Remove, and then insert the imaging kit.
Do dark lines appear on prints?

Settings > Troubleshooting > Print Quality Test Pages. For non-touch-screen printer models, press to navigate through the settings.

Step 1 Using a blank sheet of paper, make a two‑sided copy using the ADF.
Go to step 2. Go to step 3.
Do vertical dark lines or streaks appear on prints?
Step 2 Using a damp, soft, lint-free cloth, wipe the following areas:
Go to step 3. The problem is solved.


Do vertical dark lines or streaks appear on prints?
Troubleshooting 216 · Action Yes No

Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type
from the Printing Preferences or Print dialog.
Settings > Paper > Tray Configuration > Paper Size/Type b Print the document.
Do vertical dark lines or streaks appear on prints?
Go to step 5. The problem is solved.
a Load paper from a fresh package.
Do vertical dark lines or streaks appear on prints?
Contact customer support.
The problem is solved.
a Remove, and then insert the imaging kit.
Do vertical dark lines or streaks appear on prints?


Settings > Troubleshooting > Print Quality Test Pages. For non-touch-screen printer models, press to navigate through the settings. • If horizontal white lines keep appearing on your prints, then see the “Repeating defects” topic.
Go to step 2. The problem is solved.
a Depending on your operating system, specify the paper type
from the Printing Preferences or Print dialog.
Settings > Paper > Tray Configuration > Paper Size/Type b Print the document.
Do horizontal white lines appear on prints?
Contact customer support.
The problem is solved.
a Remove, and then insert the imaging kit.
Do horizontal white lines appear on prints?

Settings > Troubleshooting > Print Quality Test Pages. For non-touch-screen printer models, press to navigate through the settings.

Go to step 2. The problem is solved.
a Depending on your operating system, specify the paper type
from the Printing Preferences or Print dialog.
Settings > Paper > Tray Configuration > Paper Size/Type b Print the document.
Do vertical white lines appear on prints?
Go to step 3. The problem is solved.
Check if you are using the recommended paper type.
a Load the paper source with the recommended paper type. b Print the document.
Do vertical white lines appear on prints?
Contact customer support.
The problem is solved.
a Remove, and then insert the imaging kit.
Do vertical white lines appear on prints?

Settings > Troubleshooting > Print Quality Test Pages. For non-touch-screen printer models, press to navigate through the settings.

a Using the Print Quality Test Pages, measure the distance
Take note of the distance, and then contact customer support.
Take note of the distance, and then contact customer support.
between the repeating defects on the affected color page. b Check if the repeating defects match any of the following
measurements:
Do the repeating defects match any of the measurements?
The problem is solved.
Go to step 2.
a From the control panel, check if the documents appear in the
Held Jobs list.
Are the documents printed?
Step 2 The print job may contain a formatting error or invalid data.
The problem is solved.
Go to step 3.
Are the documents printed?

The problem is solved.
Go to step 4.
If you are printing from the Internet, then the printer may be reading the multiple job titles as duplicates.
a Open the Printing Preferences dialog. b From the Print and Hold section, select Keep duplicate
documents. c Enter a PIN. d Resend the print job.
a Save and name each job differently. b Send the job individually.
Are the documents printed?
The problem is solved.
Go to step 5.
a Delete some held jobs to free up printer memory. b Resend the print job.
Are the documents printed?
The problem is solved.
Contact customer support.
a Add printer memory. b Resend the print job.
Are the documents printed?

Go to step 2. The problem is solved.
Make sure that the printer cable is securely connected to the printer and to the computer, print server, option, or other network device.
Is the printer printing slow?
Go to step 3. The problem is solved.
a Make sure that the printer is not in Eco‑Mode or Quiet Mode.
Settings > Device > Power Management > Eco‑Mode • From the control panel, navigate to:
Settings > Device > Maintenance > Configuration Menu > Device Operations > Quiet Mode
For non‑touch‑screen printer models, press to navigate through the settings. b Print the document.
Is the printer printing slow?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the print
resolution from the Printing Preferences or Print dialog. b Set the resolution to 4800 CQ.
c Print the document.
Is the printer printing slow?
Go to step 5. The problem is solved.
a From the control panel, navigate to:
Settings > Print > Quality > Print Resolution
For non‑touch‑screen printer models, press to navigate through the settings. b Set the resolution to 4800 CQ.
c Print the document.
Is the printer printing slow?

Go to step 6. The problem is solved.
a Depending on your operating system, specify the paper type
from the Printing Preferences or Print dialog.
Is the printer printing slow?
Go to step 7. The problem is solved.
a Make sure that the printer settings for Texture and Weight
match the paper being loaded.
From the control panel, navigate to:
Settings > Paper > Media Configuration > Media Types
Is the printer printing slow?
Step 7 Remove held jobs.
Go to step 8. The problem is solved.
Is the printer printing slow?
Go to step 9. The problem is solved.
a Make sure that the printer is not overheating.
Is the printer printing slow?
Contact customer support.
The problem is solved.
a Add more printer memory. b Print the document.
Is the printer printing slow?

The problem is solved.
Go to step 2.
a From the document you are trying to print, open the Print
dialog, and then check if you have selected the correct printer. b Print the document.
Is the document printed?
The problem is solved.
Go to step 3.
a Check if the printer is on. b Resolve any error messages that appear on the display.
c Print the document.
Is the document printed?
The problem is solved.
Go to step 4.
a Check if the ports are working and if the cables are securely
connected to the computer and the printer.
For more information, see the setup documentation that came with the printer. b Print the document.
Is the document printed?
The problem is solved.
Go to step 5.
a Turn off the printer, wait for about 10 seconds, and then turn on
the printer. b Print the document.
Is the document printed?
The problem is solved.
Contact customer support.
a Remove, and then reinstall the print driver. b Print the document.
Is the document printed?

The problem is solved.
Go to step 2.
Check if the power cord is connected to the electrical outlet.
Is the printer responding?
Turn on the switch or reset the breaker.
Go to step 3.
Check if the electrical outlet is turned off by a switch or breaker.
Is the electrical outlet turned off by a switch or breaker?
Go to step 4. Turn on the printer.
Check if the printer is on.
Is the printer on?
Press the power button to wake the printer.
Go to step 5.
Check if the printer is in Sleep or Hibernate mode.
Is the printer in Sleep or Hibernate mode?
Go to step 6. Insert the cables to the correct ports.
Check if the cables connecting the printer and the computer are inserted to the correct ports.
Are the cables inserted to the correct ports?
The problem is solved.
Go to step 7.
Turn off the printer, install the hardware options, and then turn on the printer.
For more information, see the documentation that came with the option.
Is the printer responding?
The problem is solved.
Go to step 8.
Install the correct print driver.
Is the printer responding?
Step 8 Turn off the printer, wait for about 10 seconds, and then turn on the printer.
The problem is solved.
Contact customer support.
Is the printer responding?

Go to step 2. Load the correct paper size and paper type.
a Check if you are printing on the correct paper. b Print the document.
Is the document printed on the correct paper?
The problem is solved.
Go to step 3.
a Depending on your operating system, specify the paper size
and paper type from the Printing Preferences or Print dialog.
For non‑touch‑screen printer models, press to navigate through the settings. b Make sure that the settings match the paper loaded.
c Print the document.
Is the document printed on the correct paper?
The problem is solved.
Contact customer support.
a Check if the trays are linked.
For more information, see “Linking trays” on page 34. b Print the document.
Is the document printed from the correct tray?
1 From the control panel, navigate to:
Settings > Print > Quality > Toner Darkness
For non-touch-screen printer models, press to navigate through the settings.
2 Adjust the setting.
3 Apply the changes.

For non-touch-screen printer models, press to navigate through the settings.
1 From the control panel, navigate to:
Settings > Print > Quality > Advanced Imaging > Color Correction
2 From the Color Correction menu, select Manual > Color Correction Content.
3 Choose the appropriate color conversion setting.
Object type Color conversion tables
RGB Text RGB Graphics
CMYK Text CMYK Graphics
What is RGB color?
RGB color is a method of describing colors by indicating the amount of red, green, or blue used to produce a certain color. Red, green, and blue light can be added in various amounts to produce a large range of colors observed in nature. Computer screens, scanners, and digital cameras use this method to display colors.
What is CMYK color?
CMYK color is a method of describing colors by indicating the amount of cyan, magenta, yellow, and black used to reproduce a particular color. Cyan, magenta, yellow, and black inks or toners can be printed in various amounts to produce a large range of colors observed in nature. Printing presses, inkjet printers, and color laser printers create colors in this manner.
How is color specified in a document to be printed?
Software programs are used to specify and modify the document color using RGB or CMYK color combinations. For more information, see the software program Help topics.
Troubleshooting 227 · RGB Image · CMYK Image

How does the printer know what color to print?
When printing a document, information describing the type and color of each object is sent to the printer and is passed through color conversion tables. Color is translated into the appropriate amounts of cyan, magenta, yellow, and black toner used to produce the color you want. The object information determines the application of color conversion tables. For example, it is possible to apply one type of color conversion table to text while applying a different color conversion table to photographic images.
What is manual color correction?
When manual color correction is enabled, the printer employs user‑selected color conversion tables to process objects. Manual color correction settings are specific to the type of object being printed (text, graphics, or images). It is also specific to how the color of the object is specified in the software program (RGB or CMYK combinations). To apply a different color conversion table manually, see “Modifying the colors in printed output” on page 227.
If the software program does not specify colors with RGB or CMYK combinations, then manual color correction is not useful. It is also not effective if the software program or the computer operating system controls the adjustment of colors. In most situations, setting the Color Correction to Auto generates preferred colors for the documents.
How can I match a particular color (such as a corporate logo)?
From the printer Quality menu, nine types of Color Samples sets are available. These sets are also available from the Color Samples page of the Embedded Web Server. Selecting any sample set generates multiple‑page prints consisting of hundreds of colored boxes. Each box contains a CMYK or RGB combination, depending on the table selected. The observed color of each box is obtained by passing the CMYK or RGB combination labeled on the box through the selected color conversion table.
By examining Color Samples sets, you can identify the box with color closest to the color being matched. The color combination labeled on the box can then be used for modifying the color of the object in a software program. For more information, see the software program Help topics. Manual color correction may be necessary to use the selected color conversion table for the particular object.
Selecting which Color Samples set to use for a particular color‑matching problem depends on:
If the software program does not specify colors with RGB or CMYK combinations, then the Color Samples pages are not useful. Additionally, some software programs adjust the RGB or CMYK combinations specified in the program through color management. In these situations, the printed color may not be an exact match of the Color Samples pages.
Troubleshooting 228

Go to step 2. The problem is solved.
Perform Color Adjust.
a From the control panel, navigate to:
Settings > Print > Quality > Advanced Imaging > Color Adjust
For non-touch-screen printer models, press to navigate through the settings. b Print the document.
Does the print appear tinted?
Contact customer support.
The problem is solved.
a From the control panel, navigate to:
Settings > Print > Quality > Advanced Imaging > Color Balance
For non-touch-screen printer models, press to navigate through the settings. b Adjust the settings.
c Print the document.
Does the print appear tinted?
The problem is solved.
Go to step 2.
Resolve any error messages that appear on the display.
Can you send or receive a fax?
Step 2 Make sure that the cable connections for the following equipment are secure:
The problem is solved.
Go to step 3.
Can you send or receive a fax?

Go to step 5. Go to step 4.
Check for a dial tone.
Can you hear a dial tone?
Step 4 Check the telephone wall jack.
The problem is solved.
Go to step 5.
a Connect the analog telephone directly to the wall jack. b Listen for a dial tone.
c If you do not hear a dial tone, then use a different telephone
cable. d If you still do not hear a dial tone, then connect the analog
telephone to a different wall jack. e If you hear a dial tone, then connect the printer to that wall jack.
Can you send or receive a fax?
The problem is solved.
Go to step 6.
Check if the printer is connected to an analog phone service or to the correct digital connector.
Can you send or receive a fax?
The problem is solved.
Go to step 7.
Temporarily disconnect other equipment and disable other telephone services.
a Disconnect other equipment (such as answering machines,
computers, modems, or telephone line splitters) between the printer and the telephone line. b Disable call waiting and voice mail. For more information,
contact your telephone company.
Can you send or receive a fax?

The problem is solved.
Contact customer support.
Scan the original document one page at a time.
a Dial the fax number. b Scan the document.
Can you send or receive a fax?
The problem is solved.
Go to step 2.
Load the original document properly into the ADF tray or on the scanner glass.
Can you send faxes?
The problem is solved.
Contact customer support.
Set up the shortcut number properly.
Can you send faxes?
Step 1 Make sure that the paper source is not empty.
The problem is solved.
Go to step 2.
Can you receive faxes?
The problem is solved.
Go to step 3.
Check the ring count delay settings.
From the control panel, navigate to:
Settings > Fax > Analog Fax Setup > Fax Receive Settings > Rings to Answer
For non-touch-screen printer models, press to navigate through the settings.
Can you receive faxes?

The problem is solved.
Contact customer support.
If the printer is printing blank pages, then see “Blank or white pages” on page 200.
Can you receive faxes?
The problem is solved.
Go to step 2.
Make sure that there are no print quality defects.
a From the control panel, navigate to Settings > Troubleshooting
> Print Quality Test Pages. For non-touch-screen printer
models, press to navigate through the settings. b Correct any print quality defects. For more information, see
“Print quality is poor” on page 200.
Is the fax print quality satisfactory?
Step 2 Decrease the incoming fax transmission speed.
The problem is solved.
Contact customer support.
a From the control panel, navigate to:
Settings > Fax > Analog Fax Setup > Fax Receive Settings > Admin Controls
For non-touch-screen printer models, press to navigate through the settings. b From the Max Speed menu, select a lower transmission speed.
Is the fax print quality satisfactory?
The problem is solved.
Go to step 2.
a Turn off the printer, wait for about 10 seconds, and then turn it
back on. b Resend the scan job.
Can you send the scan job?

The problem is solved.
Contact customer support.
a Make sure that the cables between the printer and the print
server are secure.
For more information, see the setup documentation that came with the printer. b Resend the scan job.
Can you send the scan job?
The problem is solved.
Go to step 2.
a Make sure that the document or photo is loaded facedown on
the upper left corner of the scanner glass. b Copy the document or photo.
Is the document or photo copied correctly?
The problem is solved.
Contact customer support.
a Match the paper size setting and the paper loaded in the tray. b Copy the document or photo.
Is the document or photo copied correctly?
The problem is solved.
Go to step 2.
a Clean the scanner glass and the ADF glass with a damp, soft,
lint‑free cloth. If your printer has a second ADF glass inside the ADF, then also clean that glass.
For more information, see “Cleaning the scanner” on page 154. b Make sure that the document or photo is loaded facedown on
the upper left corner of the scanner glass. c Copy the document or photo.
Is the copy quality satisfactory?

The problem is solved.
Contact customer support.
a Check the quality of the original document or photo. b Adjust the scan quality settings.
c Copy the document or photo.
Is the copy quality satisfactory?
Step 1 Check the cable connections.
The problem is solved.
Go to step 2.
a Make sure that the Ethernet or USB cable is securely connected
to the computer and the printer. b Resend the scan job.
Is the scan job successful?
The problem is solved.
Go to step 3.
Check the file you want to scan.
a Make sure that the file name is not already used in the
destination folder. b Make sure that the document or photo you want to scan is not
open in another application. c Resend the scan job.
Is the scan job successful?
The problem is solved.
Contact customer support.
a Make sure that the Append time stamp or the Overwrite
existing file check box is selected in the destination configuration settings. b Resend the scan job.
Is the scan job successful?
Remove obstructions that keep the scanner unit open.
The problem is solved.
Contact customer support.
Did the scanner unit close correctly?

Close all applications that are interfering with the scan.
Contact customer support.
The problem is solved.
Does scanning take too long or freeze the computer?
The problem is solved.
Go to step 2.
a Check if the power cord is connected properly to the printer
and the electrical outlet.
Is the scanner responding?
The problem is solved.
Go to step 3.
a Check if the printer is turned on. b Resolve any error messages that appear on the display.
c Copy or scan the document.
Is the scanner responding?
The problem is solved.
Contact customer support.
a Turn off the printer, wait for about 10 seconds, and then turn the
printer on. b Copy or scan the document.
Is the scanner responding?
1 From the control panel, navigate to:
Settings > Device > Maintenance > Configuration Menu > Scanner Configuration > Scanner Manual Registration
For non-touch-screen printer models, press to navigate through the settings.
2 From the Print Quick Test menu, select Start.
3 Place the Print Quick Test page on the scanner glass, and then select Flatbed Registration.
4 From the Copy Quick Test menu, select Start.

5 Compare the Copy Quick Test page with the original document.
6 Repeat step 4 and step 5 until the margins of the Copy Quick Test page closely match the original document.
1 From the control panel, navigate to:
Settings > Device > Maintenance > Configuration Menu > Scanner Configuration > Scanner Manual Registration
For non-touch-screen printer models, press to navigate through the settings.
2 From the Print Quick Test menu, select Start.
3 Place the Print Quick Test page on the ADF tray.
4 Select Front ADF Registration or Rear ADF Registration.
5 From the Copy Quick Test menu, select Start.
6 Compare the Copy Quick Test page with the original document.
7 Repeat step 5 and step 6 until the margins of the Copy Quick Test page closely match the original document.
Before contacting customer support, make sure to have the following information:
Go to http://support.lexmark.com to receive e‑mail or chat support, or browse through the library of manuals, support documentation, drivers, and other downloads.
Technical support via telephone is also available. In the U.S. or Canada, call 1-800-539-6275. For other countries or regions, go to http://support.lexmark.com.
Troubleshooting 236

Upgrading and migrating 237
Hardware
CAUTION—SHOCK HAZARD: To avoid the risk of electrical shock, if you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet, and then from the printer.
3 Using a flat‑head screwdriver, remove the controller board access cover.

Upgrading and migrating 238


Upgrading and migrating 239
4 Attach the access cover.

5 Connect the power cord to the printer, and then to the electrical outlet.
6 Turn on the printer.

Upgrading and migrating 240
CAUTION—SHOCK HAZARD: To avoid the risk of electrical shock, if you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet, and then from the printer.
3 Using a flat‑head screwdriver, remove the controller board access cover.

Upgrading and migrating 241
4 Unpack the memory card.
5 Insert the memory card until it clicks into place.

6 Attach the access cover.
7 Connect the power cord to the printer, and then to the electrical outlet.
8 Turn on the printer.
CAUTION—SHOCK HAZARD: To avoid the risk of electrical shock, if you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet, and then from the printer.
3 Using a flat‑head screwdriver, remove the controller board access cover.

Upgrading and migrating 242
4 Unpack the optional card.
5 Push the card firmly into place.


Upgrading and migrating 243
6 Attach the access cover.
7 Connect the power cord to the printer, and then to the electrical outlet.
8 Turn on the printer.
CAUTION—SHOCK HAZARD: To avoid the risk of electrical shock, if you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet, and then from the printer.
3 Using a flat‑head screwdriver, remove the controller board access cover.

Upgrading and migrating 244
4 Unpack the printer hard disk.
5 Attach the hard disk, and then connect the hard disk interface cable to the controller board.

Upgrading and migrating 245

6 Attach the access cover.
7 Connect the power cord to the printer, and then to the electrical outlet.
8 Turn on the printer.

Upgrading and migrating 246
CAUTION—SHOCK HAZARD: To avoid the risk of electrical shock, if you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet, and then from the printer.
3 Unpack the optional tray, and then remove all packing material.
4 Align the printer with the optional tray, and then lower the printer into place.


Upgrading and migrating 247
5 Connect the power cord to the printer, and then to the electrical outlet.
6 Turn on the printer.
Add the tray in the print driver to make it available for print jobs. For more information, see “Adding available options in the print driver” on page 247.
2 Run the installer, and then follow the instructions on the computer screen.
3 For Macintosh users, add the printer.
1 Open the printers folder.
3 Navigate to the Configuration tab, and then select Update Now ‑ Ask Printer.
4 Apply the changes.
1 From System Preferences in the Apple menu, navigate to your printer, and then select Options & Supplies.
2 Navigate to the list of hardware options, and then add any installed options.
3 Apply the changes.

Upgrading and migrating 248
You can export the configuration settings of your printer into a text file, and then import the file to apply the settings to other printers.
1 Open a web browser, and then type the printer IP address in the address field.
2 Export or import a configuration file for one or multiple applications.
a From the Embedded Web Server, click Apps > the application that you want > Configure. b Click Export or Import.
a From the Embedded Web Server, click Export Configuration or Import Configuration. b Follow the instructions on the screen.
Some applications require a minimum device firmware level to operate correctly.
For more information on updating the device firmware, contact your Lexmark representative.
1 From the Embedded Web Server, click Settings > Device > Update Firmware.
2 Browse to locate the required flash file.
3 Apply the changes.

Product name:
Lexmark CX421adn; Lexmark CX522ade; Lexmark CX622ade; Lexmark CX625ade, CX625adhe; Lexmark MC2325adw; Lexmark MC2425adw; Lexmark MC2535adw; Lexmark MC2640adwe; Lexmark XC2235; Lexmark XC4240 MFPs
Machine type:
Model(s):
081, 230, 238, 436, 486, 496, 636, 638, 686, 698, 836, 838, 898
The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.
References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.
For Lexmark technical support, visit http://support.lexmark.com.
For information on supplies and downloads, visit www.lexmark.com.
© 2018 Lexmark International, Inc.
All rights reserved.
The Software Program and any related documentation are "Commercial Items," as that term is defined in 48 C.F.R. 2.101, "Computer Software" and "Commercial Computer Software Documentation," as such terms are used in 48 C.F.R. 12.212 or 48 C.F.R. 227.7202, as applicable. Consistent with 48 C.F.R. 12.212 or 48 C.F.R. 227.7202-1 through 227.7207-4, as applicable, the Commercial Computer Software and Commercial Software
December 2018

Documentation are licensed to the U.S. Government end users (a) only as Commercial Items and (b) with only those rights as are granted to all other end users pursuant to the terms and conditions herein.
Lexmark and the Lexmark logo are trademarks or registered trademarks of Lexmark International, Inc. in the United States and/or other countries.
Google Cloud Print and Google Chrome are trademarks of Google Inc. Android and Google Play are trademarks of Google LLC.
Macintosh, Mac, App Store, and Safari are trademarks of Apple Inc. AirPrint and the AirPrint logo are trademarks of Apple, Inc.
Microsoft, Windows, and Internet Explorer are either registered trademarks or trademarks of the Microsoft group of companies in the United States and other countries.
Mopria®, the Mopria® logo, and the Mopria® Alliance logo are registered trademarks and service marks of Mopria Alliance, Inc. in the United States and other countries. Unauthorized use is strictly prohibited.
PCL® is a registered trademark of the Hewlett-Packard Company. PCL is Hewlett-Packard Company’s designation of a set of printer commands (language) and functions included in its printer products. This printer is intended to be compatible with the PCL language. This means the printer recognizes PCL commands used in various application programs, and that the printer emulates the functions corresponding to the commands.
PostScript is a registered trademark of Adobe Systems Incorporated in the United States and/or other countries.
All other trademarks are the property of their respective owners.
AirPrint and the AirPrint logo are trademarks of Apple, Inc.
All licensing notices associated with this product can be viewed from the CD:\NOTICES directory of the installation software CD.
The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.
1-meter average sound pressure, dBA
Printing 53 (one-sided); 55 (two-sided)
Values are subject to change. See www.lexmark.com for current values.
Scanning 53 · Copying 56 · Ready 16

The WEEE logo signifies specific recycling programs and procedures for electronic products in countries of the European Union. We encourage the recycling of our products.
If you have further questions about recycling options, visit the Lexmark Web site at www.lexmark.com for your local sales office phone number.
This product complies with the India E-Waste (Management and Handling) Rules, 2011, which prohibit use of lead, mercury, hexavalent chromium, polybrominated biphenyls, or polybrominated diphenyl ethers in concentrations exceeding 0.1% by weight and 0.01% by weight for cadmium, except for the exemption set in Schedule II of the Rules.
Do not dispose of the printer or supplies in the same manner as normal household waste. Consult your local authorities for disposal and recycling options.
This symbol identifies static-sensitive parts. Do not touch the areas near these symbols without first touching a metal surface in an area away from the symbol.

To prevent damage from electrostatic discharge when performing maintenance tasks such as clearing paper jams or replacing supplies, touch any exposed metal frame of the printer before accessing or touching interior areas of the printer even if the symbol is not present.
Any Lexmark product bearing the ENERGY STAR emblem on the product or on a start-up screen is certified to comply with Environmental Protection Agency (EPA) ENERGY STAR requirements as configured when shipped by Lexmark.
Operating temperature and relative humidity 10 to 32.2°C (50 to 90°F) and 15 to 80% RH 15.3 to 32.2°C (60 to 90°F) and 8 to 80% RH Maximum wet bulb temperature2: 22.8°C (73°F) Non-condensing environment
Printer / cartridge / imaging unit long- term storage1
Printer / cartridge / imaging unit short-term shipping
-40 to 43.3°C (-40 to 110°F)
1 Supplies shelf life is approximately 2 years. This is based on storage in a standard office environment at 22°C (72°F) and 45% humidity.
2 Wet-bulb temperature is determined by the air temperature and the relative humidity.
The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR, Chapter I, Subchapter J for Class I (1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements of IEC 60825-1: 2014.
Class I laser products are not considered to be hazardous. The printer contains internally a Class IIIb (3b) AlGaInP laser that is nominally 15 milliwatts operating in the wavelength region of 650–670 nanometers and enclosed in a non-serviceable printhead assembly. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service conditions.
The following table documents the power consumption characteristics of the product.

Mode Description Power consumption (Watts)
Printing The product is generating hard‑copy output from electronic inputs.
One-sided: 400 (CX421, MC2325, MC2425); 530 (CX522, MC2535, XC2235); 580 (CX622, MC2640); 580 (CX625, XC4240) Two-sided: 280 (CX421, MC2325, MC2425); 360 (CX522, MC2535, XC2235); 420 (CX622, MC2640); 420 (CX625, XC4240)
Copy The product is generating hard‑copy output from hard‑copy original documents.
425 (CX421, MC2325, MC2425); 485 (CX522, MC2535, XC2235); 560 (CX622, MC2640); 540 (CX625, XC4240)
Scan The product is scanning hard‑copy documents.
25 (CX421, MC2325, MC2425); 28.5 (CX522, MC2535, XC2235); 29.5 (CX622, MC2640); 28 (CX625, XC4240)
Ready The product is waiting for a print job. 25 (CX421, MC2325, MC2425); 26.5 (CX522, MC2535, XC2235); 28.5 (CX622, MC2640); 29.5 (CX625, XC4240)
Sleep Mode The product is in a high‑level
2.2 (CX421, MC2325, MC2425); 1.9 (CX522, MC2535, XC2235); 1.8 (CX622, MC2640); 1.8 (CX625, XC4240)
energy‑saving mode.
Hibernate The product is in a low‑level energy‑saving mode.
0.2 (CX421, MC2325, MC2425); 0.2 (CX522, MC2535, XC2235); 0.2 (CX622, MC2640); 0.2 (CX625, XC4240)
Off The product is plugged into an electrical outlet, but the power switch is turned off.
0.2 (CX421, MC2325, MC2425); 0.2 (CX522, MC2535, XC2235); 0.2 (CX622, MC2640); 0.2 (CX625, XC4240)
The power consumption levels listed in the previous table represent time-averaged measurements. Instantaneous power draws may be substantially higher than the average.
Values are subject to change. See www.lexmark.com for current values.
This product is designed with an energy-saving mode called Sleep Mode. The Sleep Mode saves energy by lowering power consumption during extended periods of inactivity. The Sleep Mode is automatically engaged after this product is not used for a specified period of time, called the Sleep Mode Timeout.
Factory default Sleep Mode Timeout for this product (in minutes): 15
By using the configuration menus, the Sleep Mode Timeout can be modified between 1 minute and 120 minutes. Setting the Sleep Mode Timeout to a low value reduces energy consumption, but may increase the response time of the product. Setting the Sleep Mode Timeout to a high value maintains a fast response, but uses more energy.
This product is designed with an ultra‑low power operating mode called Hibernate mode. When operating in Hibernate Mode, all other systems and devices are powered down safely.
The Hibernate mode can be entered in any of the following methods:

Factory default Hibernate Timeout for this product in all countries or regions 3 days
The amount of time the printer waits after a job is printed before it enters Hibernate mode can be modified between one hour and one month.
If this product has an off mode which still consumes a small amount of power, then to completely stop product power consumption, disconnect the power supply cord from the electrical outlet.
It is sometimes helpful to estimate the total product energy usage. Since power consumption claims are provided in power units of Watts, the power consumption should be multiplied by the time the product spends in each mode in order to calculate energy usage. The total product energy usage is the sum of each mode's energy usage.
This section contains regulatory information pertaining to products that contain the analog facsimile card:
Lexmark Regulatory Type/Model Number:
Notice to users of the US telephone network: FCC requirements
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the Administrative Council for Terminal Attachments (ACTA). On the back of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to your telephone company.
This equipment uses the RJ-11C Universal Service Order Code (USOC) jack.
A plug and jack used to connect this equipment to the premises’ wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. Use a compliant telephone cord (RJ-11) that is 26 AWG or larger when connecting this product to the public switched telephone network. See your setup documentation for more information.
The Ringer Equivalence Number (REN) is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact your local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (for example, 03 is a REN of 0.3). For earlier products, the REN is shown separately on the label.
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify the customer as soon as possible. You will also be advised of your right to file a complaint with the FCC.

The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of this equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.
If you experience trouble with this equipment, for repair or warranty information, contact Lexmark International, Inc. at www.lexmark.com or your Lexmark representative. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
This equipment contains no user serviceable parts. For repair and warranty information, contact Lexmark International, Inc. See the previous paragraph for contact information.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission, or corporation commission for information.
If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including fax machines, to send any message unless said message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message, and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges.)
See your user documentation in order to program this information into your fax machine.
This product meets the applicable Industry Canada technical specifications.
The Ringer Equivalence Number (REN) indicates the maximum number of devices allowed to be connected to a telephone interface. The termination of an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices not exceed five. The REN is located on the product label.
This equipment uses CA11A telephone jacks.
Ce produit est conforme aux spécifications techniques d’Industrie Canada.
Le numéro REN (ringer equivalence number : numéro d’équivalence de sonnerie) indique le nombre maximum d'appareils pouvant être connectés à l’interface téléphonique. En bout de ligne, le nombre d’appareils qui peuvent être connectés n’est pas directement limité, mais la somme des REN de ces appareils ne doit pas dépasser cinq. Le numéro REN est indiqué sur l'étiquette produit.
Cet équipement utilise des prises de téléphone CA11A.
The following are special conditions for the Facsimile User Instructions. The grant of a telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any

sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom's network services.
This equipment shall not be set up to make automatic calls to the Telecom “111” Emergency Service.
This equipment may not provide for the effective hand-over of a call to another device connected to the same line.
This equipment should not be used under any circumstances that may constitute a nuisance to other Telecom customers.
This equipment is not capable, under all operating conditions, of correct operation at the higher speeds for which it is designed. Telecom will accept no responsibility should difficulties arise in such circumstances.
The decadic (or pulse) dialing on this device is unsuitable for use on the Telecom network in New Zealand.
For correct operation, the total of all the Ringer Equivalence Numbers (RENs) of all parallel devices connected to the same telephone line may not exceed 5. The REN of this device is located on the label.
This device uses an RJ-11C modular connector. Contact your point of purchase if a BT adapter is required. The Lexmark part number is 80D1873.
Some parameters required for compliance with Telecom's telepermit requirements are dependent on the equipment associated with this device. The associated equipment shall be set to operate within the following limits for compliance to Telecom's specifications:
The installed optional modem is in compliance with Japanese Telecommunication Law and has been Certified by JATE, with the following Certification Number:
Lexmark International, Inc.
A18-0046001
Using this product in Switzerland
This product requires a Swiss billing tone filter (Lexmark part number 80D1877) to be installed on any line which receives metering pulses in Switzerland.

Cet appareil nécessite l’utilisation d’un filtre de tonalité de facturation suisse (nº de référence Lexmark : 80D1877) devant être installé sur toute ligne recevant des impulsions de comptage en Suisse.
Für dieses Produkt muss ein schweizerischer Billing Tone Filter zur Zählzeichenübertragung (Lexmark Teilenummer 80D1877) für jede Leitung installiert werden, über die in der Schweiz Zeitsteuertakte übertragen werden.
Questo prodotto richiede un filtro toni Billing svizzero, (codice Lexmark 80D1877) da installare su tutte le linee che ricevono impulsi remoti in Svizzera.
This section contains regulatory information that applies only to wireless models.
If in doubt as to whether your model is a wireless model, go to http://support.lexmark.com.
Wireless models contain one of the following modular components:
Lexmark Regulatory Type/Model LEX-M07-001; FCC ID:IYLLEXM07001; IC:2376A-LEXM07001 Lexmark Regulatory Type/Model Number LEX-M08-001; FCC ID:IYLLEXM08001; IC:2376A-LEXM08001
To determine which modular components are installed in your particular product, refer to the labeling on your actual product.
The radiated output power of this device is far below the radio frequency exposure limits of the FCC and other regulatory agencies. A minimum separation of 20 cm (8 inches) must be maintained between the antenna and any persons for this device to satisfy the RF exposure requirements of the FCC and other regulatory agencies.
This device complies with Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Cet appareil est conforme aux normes RSS exemptes de licence d'Industrie Canada. Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interférences et (2) il doit accepter toutes les interférences, y compris les celles qui peuvent entraîner un fonctionnement indésirable.
This product is in conformity with the protection requirements of EC Council directive 2014/53/EU on the approximation and harmonization of the laws of the Member States relating to radio equipment.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY. A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative or may be obtained at www.lexmark.com/en_us/about/regulatory-compliance/european-union-declaration-of-conformity.html.
Compliance is indicated by the CE marking:
This radio product transmits in the 2.4GHz (2.412–2.472GHz) band in the EU. The maximum transmitter EIRP power output, including antenna gain, is ≤ 20dBm.
The following information applies to all CX421 (7529-230), CX522 (7529-436), MC2325 (7529-081), MC2425 (7529-238), MC2535 (7529-486), and XC2235 (7529-496) printer models.
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The FCC Class B limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

The manufacturer is not responsible for radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment.
Any questions regarding this compliance information statement should be directed to:
Director of Lexmark Technology & Services Lexmark International, Inc. 740 West New Circle Road Lexington, KY 40550 Telephone: (859) 232–3000 E-mail: regulatory@lexmark.com
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Standard ICES-003.
Cet appareil numérique de classe B est conforme aux exigences de la norme canadienne relative aux équipements pouvant causer des interférences NMB-003.
この装置は、クラス B 情報技術装置です。この装置は、家庭環境で使用することを目的としていますが、この 装置がラジオやテレビジョン受信機に近接して使用されると、受信障害を引き起こすことがあります。 取扱説明書に従って正しい取り扱いをしてください。
VCCI-B
European Community (EC) directives conformity
This product is in conformity with the protection requirements of EC Council directives 2014/30/EU, 2014/35/EU, 2009/125/EC, and 2011/65/EU on the approximation and harmonization of the laws of the Member States

relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits, the ecodesign of energy-related products, and on the restrictions of use of certain hazardous substances in electrical and electronic equipment.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY. A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative or may be obtained at www.lexmark.com/en_us/about/regulatory-compliance/european-union-declaration-of-conformity.html.
This product satisfies the Class B limits of EN 55022 and EN55032 and safety requirements of EN 60950‑1 or EN 62368-1.
The following information applies only to the CX622 (7529-636, 7529-638), CX625 (7529-836, 7529-838), MC2640 (7529-686), and XC4240 (7529-898) printer models.
This product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The FCC Class A limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
The manufacturer is not responsible for any radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment.
Any questions regarding this compliance information statement should be directed to:
Director of Lexmark Technology & Services Lexmark International, Inc. 740 West New Circle Road Lexington, KY 40550 Telephone: (859) 232–3000 E-mail: regulatory@lexmark.com

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Standard ICES-003.
Cet appareil numérique de classe A est conforme aux exigences de la norme canadienne relative aux équipements pouvant causer des interférences NMB-003.
Este produto não é apropriado para uso em ambientes domésticos, pois poderá causar interferências eletromagnéticas que obrigam o usuário a tomar medidas necessárias para minimizar estas interferências.
This product is in conformity with the protection requirements of EC Council directives 2014/30/EU, 2014/35/EU, and 2011/65/EU on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits, and on the restrictions of use of certain hazardous substances in electrical and electronic equipment.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY. A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative or may be obtained at www.lexmark.com/en_us/about/regulatory-compliance/european-union-declaration-of-conformity.html.
This product satisfies the Class A limits of EN 55022 and EN55032 and safety requirements of EN 60950‑1 or EN 62368-1.
This is a product that complies with the emission requirements of EN55022 and EN55032 Class A limits and immunity requirements of EN55024. This product is not intended to be used in residential/domestic environments.
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

STATEMENT OF LIMITED WARRANTY FOR LEXMARK LASER PRINTERS, LEXMARK LED PRINTERS, AND LEXMARK MULTIFUNCTION LASER
This limited warranty applies to the United States and Canada. For customers outside the U.S., refer to the country-specific warranty information that came with your product.
This limited warranty applies to this product only if it was originally purchased for your use, and not for resale, from Lexmark or a Lexmark Remarketer, referred to in this statement as “Remarketer.”
Lexmark warrants that this product:
—Is manufactured from new parts, or new and serviceable used parts, which perform like new parts
—Is, during normal use, free from defects in material and workmanship
If this product does not function as warranted during the warranty period, contact a Remarketer or Lexmark for repair or replacement (at Lexmark's option).
If this product is a feature or option, this statement applies only when that feature or option is used with the product for which it was intended. To obtain warranty service, you may be required to present the feature or option with the product.
If you transfer this product to another user, warranty service under the terms of this statement is available to that user for the remainder of the warranty period. You should transfer proof of original purchase and this statement to that user.
The warranty period starts on the date of original purchase as shown on the purchase receipt and ends 12 months later provided that the warranty period for any supplies and for any maintenance items included with the printer shall end earlier if it, or its original contents, are substantially used up, depleted, or consumed. Fuser Units, Transfer/Transport Units, Paper Feed items, if any, and any other items for which a Maintenance Kit is available are substantially consumed when the printer displays a “Life Warning” or “Scheduled Maintenance” message for such item.
To obtain warranty service you may be required to present proof of original purchase. You may be required to deliver your product to the Remarketer or Lexmark, or ship it prepaid and suitably packaged to a Lexmark designated location. You are responsible for loss of, or damage to, a product in transit to the Remarketer or the Lexmark designated location.
When warranty service involves the exchange of a product or part, the item replaced becomes the property of the Remarketer or Lexmark. The replacement may be a new or repaired item.
The replacement item assumes the remaining warranty period of the original product.
Replacement is not available to you if the product you present for exchange is defaced, altered, in need of a repair not included in warranty service, damaged beyond repair, or if the product is not free of all legal obligations, restrictions, liens, and encumbrances.

As part of your warranty service and/or replacement, Lexmark may update the firmware in your printer to the latest version. Firmware updates may modify printer settings and cause counterfeit and/or unauthorized products, supplies, parts, materials (such as toners and inks), software, or interfaces to stop working. Authorized use of genuine Lexmark products will not be impacted.
Before you present this product for warranty service, remove all print cartridges, programs, data, and removable storage media (unless directed otherwise by Lexmark).
For further explanation of your warranty alternatives and the nearest Lexmark authorized servicer in your area contact Lexmark on the World Wide Web.
Remote technical support is provided for this product throughout its warranty period. For products no longer covered by a Lexmark warranty, technical support may not be available or only be available for a fee.
Lexmark does not warrant uninterrupted or error-free operation of any product or the durability or longevity of prints produced by any product.
Warranty service does not include repair of failures caused by:
—Modification or unauthorized attachments
—Accidents, misuse, abuse or use inconsistent with Lexmark user’s guides, manuals, instructions or guidance
—Unsuitable physical or operating environment
—Maintenance by anyone other than Lexmark or a Lexmark authorized servicer
—Operation of a product beyond the limit of its duty cycle
—Use of printing media outside of Lexmark specifications
—Refurbishment, repair, refilling or remanufacture by a third party of products, supplies or parts
—Products, supplies, parts, materials (such as toners and inks), software, or interfaces not furnished by Lexmark
TO THE EXTENT PERMITTED BY APPLICABLE LAW, NEITHER LEXMARK NOR ITS THIRD PARTY SUPPLIERS OR REMARKETERS MAKE ANY OTHER WARRANTY OR CONDITION OF ANY KIND, WHETHER EXPRESS OR IMPLIED, WITH RESPECT TO THIS PRODUCT, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND SATISFACTORY QUALITY. ANY WARRANTIES THAT MAY NOT BE DISCLAIMED UNDER APPLICABLE LAW ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. NO WARRANTIES, EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD. ALL INFORMATION, SPECIFICATIONS, PRICES, AND SERVICES ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE.
Your sole remedy under this limited warranty is set forth in this document. For any claim concerning performance or nonperformance of Lexmark or a Remarketer for this product under this limited warranty, you may recover actual damages up to the limit set forth in the following paragraph.
Lexmark's liability for actual damages from any cause whatsoever will be limited to the amount you paid for the product that caused the damages. This limitation of liability will not apply to claims by you for bodily injury or damage to real property or tangible personal property for which Lexmark is legally liable. IN NO EVENT WILL LEXMARK BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, INCIDENTAL DAMAGE, OR OTHER ECONOMIC OR CONSEQUENTIAL DAMAGES. This is true even if you advise Lexmark or a Remarketer of the possibility of such damages. Lexmark is not liable for any claim by you based on a third party claim.

This limitation of remedies also applies to claims against any Suppliers and Remarketers of Lexmark. Lexmark's and its Suppliers' and Remarketers' limitations of remedies are not cumulative. Such Suppliers and Remarketers are intended beneficiaries of this limitation.
Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or limitation of incidental or consequential damages, so the limitations or exclusions contained above may not apply to you.
This limited warranty gives you specific legal rights. You may also have other rights that vary from state to state.





Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.