
User's Guide
Machine type(s):
Model(s):
5028, 7528 · 135, 630, 576


Conventions
Different types of caution statements include:
Safety information 5

CAUTION—POTENTIAL INJURY: Do not cut, twist, bind, crush, or place heavy objects on the power cord. Do not subject the power cord to abrasion or stress. Do not pinch the power cord between objects such as furniture and walls. If any of these things happen, a risk of fire or electrical shock results. Inspect the power cord regularly for signs of such problems. Remove the power cord from the electrical outlet before inspecting it.
CAUTION—SHOCK HAZARD: To avoid the risk of electrical shock, if you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
Safety information 6

This product is designed, tested, and approved to meet strict global safety standards with the use of specific manufacturer's components. The safety features of some parts may not always be obvious. The manufacturer is not responsible for the use of other replacement parts.
Refer service or repairs, other than those described in the user documentation, to a service representative.
This product uses a printing process that heats the print media, and the heat may cause the media to release emissions. You must understand the section in your operating instructions that discusses the guidelines for selecting print media to avoid the possibility of harmful emissions.
This product may produce small amounts of ozone during normal operation, and may be equipped with a filter designed to limit ozone concentrations to levels well below the recommended exposure limits. To avoid high ozone concentration levels during extensive usage, install this product in a well-ventilated area and replace the ozone and exhaust filters if instructed to do so in the product maintenance instructions. If there are no references to filters in the product maintenance instructions, then there are no filters requiring replacement for this product.
SAVE THESE INSTRUCTIONS.
Safety information 7

Learning about the printer 8
Finding information about the printer

Learning about the printer 9

When selecting a location for the printer, leave enough room to open trays, covers, and doors and to install hardware options.

Learning about the printer 10

You can configure your printer by adding three optional 550‑sheet trays.

Learning about the printer 11

1 Standard bin · 4 Control panel

Learning about the printer 12



Learning about the printer 13
2 Home button Go to the home screen.
3 Keypad Enter numbers or symbols in an input field.
4 Power button • Turn on or turn off the printer.
5 Stop or Cancel button Stop the current job.
6 Indicator light Check the status of the printer.
7 Volume buttons Adjust the volume of the headset or speaker.
8 Headset or speaker port Attach a headset or speaker.
9 Backspace button Move the cursor backward and delete a character in an input field.
Indicator light Printer status
Off The printer is off or in Hibernate mode.
Blue The printer is ready or processing data.
Red The printer requires user intervention.
Power button light Printer status
Off The printer is off, ready, or processing data.
Solid amber The printer is in sleep mode.
Blinking amber The printer is in hibernate mode.
When the printer is turned on, the display shows the home screen. Use the home screen buttons and icons to initiate an action.
Use the To

Learning about the printer 14

2 Job Queue Show all the current print jobs.
3 Change Language Change the language on the printer display.
5 USB Drive View, select, or print photos and documents from a flash drive.
6 Held Jobs Show all the current held print jobs.

Lock Device Prevent users from accessing any printer functions from the home screen.

Learning about the printer 15
Security
Flash Drive Print

Learning about the printer 16
From the home screen, touch Settings > Reports > Menu Settings Page.

Setting up and using the home screen applications 17
Customizing the home screen
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Settings > Device > Visible Home Screen Icons.
3 Select the icons that you want to appear on the home screen.
4 Apply the changes.
1 From the home screen, touch Change Wallpaper.
2 Select an image to use.
3 Apply the changes.
Before you begin, make sure to configure the slide show settings. For more information, see the documentation that came with the solution.
1 Insert a flash drive into the USB port.
2 From the home screen, touch Slideshow.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Apps > Forms and Favorites > Configure.
3 Click Add, and then customize the settings.

Setting up and using the home screen applications 18
4 Apply the changes.
1 From the home screen, touch Eco‑Settings.
2 Configure the Eco‑Mode settings or schedule a power-saving mode.
3 Apply the changes.
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Address Book.
3 From the Contacts section, add a contact.
4 If necessary, specify a login method to allow application access.
5 Apply the changes.
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Address Book.
3 From the Contact Groups section, add a group name.
4 Apply the changes.

Setting up and using the home screen applications 19
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Address Book.
4 Apply the changes.
1 Open a web browser, and then type the printer IP address in the address field.
2 Click Address Book.

Setting up and using the accessibility features 20
Enabling Magnification mode
1 From the control panel, press and hold the 5 key until you hear a voice message.
2 Select Magnification.
3 Select OK.
For more information on navigating a magnified screen, see “Navigating the screen using gestures” on page 21.
1 Press and hold the 5 key until a voice message is heard.
2 Select OK.
1 Press and hold the 5 key until a voice message is heard.
2 Press Tab to navigate the focus cursor to the OK button, and then press Enter.
1 From the home screen, select Settings > Device > Accessibility > Speech Rate.
2 Select the speech rate.
1 From the home screen, select Settings > Device > Accessibility > Speak Passwords/PINs.
2 Enable the setting.

Setting up and using the accessibility features 21
Double‑tap Select an option or item on the screen.
Triple‑tap Zoom in or zoom out text and images.
Swipe right or swipe down Move to the next item on the screen.
Swipe left or swipe up Move to the previous item on the screen.
Pan Access parts of the zoomed image that are beyond the limits of the screen.
Swipe up then left Exit an application and return to the home screen.
Swipe up then down Repeat a spoken prompt.
Do one or more of the following:
Gesture Function

Loading paper and specialty media 22
Setting the size and type of the specialty media
The trays automatically detect the size of plain paper. For specialty media like labels, card stock, or envelopes, do the following:
1 From the home screen, navigate to:
Settings > Paper > Tray Configuration > Paper Size/Type > select a paper source
2 Set the size and type of the specialty media.
1 From the home screen, touch Settings > Paper > Media Configuration > Universal Setup.
2 Configure the settings.
1 Remove the tray.




2 Adjust the guides to match the size of the paper you are loading.

Loading paper and specialty media 23

3 Flex, fan, and align the paper edges before loading.

4 Load the paper stack with the printable side faceup.

5 Insert the tray.
If necessary, set the paper size and type to match the paper loaded in the tray.

Loading paper and specialty media 24
1 Open the multipurpose feeder.

2 Adjust the guide to match the size of the paper you are loading.

3 Flex, fan, and align the paper edges before loading.


Loading paper and specialty media 25
4 Load the paper. • Load paper and card stock with the printable side facedown and the top edge entering the printer first.



5 From the Paper Menu in the control panel, set the paper size and type to match the paper loaded in the tray.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper.

Loading paper and specialty media 26
3 Match the paper size and type for the trays you are linking.
4 Save the settings.

Printing from a computer
1 From the document that you are trying to print, open the Print dialog.
2 If necessary, adjust the settings.
3 Print the document.
1 From the home screen, navigate to:
Forms and Favorites > select form > Print
2 If necessary, configure the print settings.
3 Send the print job.
LexmarkTM Mobile Print allows you to send documents and images directly to a supported Lexmark printer.
1 Open the document, and then send or share the document to Lexmark Mobile Print.
2 Select a printer.
3 Print the document.
Google Cloud PrintTM is a mobile printing service that allows enabled applications on mobile devices to print to any Google Cloud Print‑ready printer.
1 From the home screen of your mobile device, launch an enabled application.
2 Tap Print, and then select the printer.
3 Send the print job.
Printing 27

Mopria® Print Service is a mobile printing solution for mobile devices running on Android version 4.4 or later. It allows you to print directly to any Mopria‑certified printer.
1 From the home screen of your mobile device, launch a compatible application.
2 Tap Print, and then select the printer.
3 Send the print job.
AirPrint is a mobile printing solution that allows you to print directly from Apple devices to an AirPrint‑certified printer.
1 From the home screen of your mobile device, launch a compatible application.
2 Select an item to print, and then tap the share icon.
3 Tap Print, and then select a printer.
4 Print the document.
1 Insert a flash drive into the USB port.

Printing 28

2 From the display, touch the document that you want to print.
If necessary, configure other print settings.
3 Send the print job.
To print another document, touch USB Drive.

– The printer supports high‑speed USB flash drives with full‑speed standard. – USB flash drives must support the File Allocation Table (FAT) system.
Documents:
Printing 29

Images:
1 From the home screen, touch Settings > Security > Confidential Print Setup.
2 Configure the settings.
Max Invalid PIN Limit the number of times an invalid PIN can be entered.
Set the amount of time before confidential jobs are automatically deleted from the printer memory.
Set the amount of time before repeat jobs are deleted from the printer memory.
Verify Job Expiration Set the amount of time before verify jobs are deleted from the printer memory.
Set the amount of time before reserved jobs are deleted without being printed.
1 From the document you are trying to print, open the Print dialog.
3 Select the print job type.
4 If necessary, assign a user name.
5 Send the print job.
6 From the printer home screen, touch Held Jobs.
7 Send the print job.

1 From the home screen, touch Settings > Reports > Print > Print Fonts.
2 Touch PCL Fonts or PostScript Fonts.
1 From the home screen, touch Job Queue.
2 Select the job to cancel.
2 Select the job to cancel.
Printing 31

Securing the printer 32
Erasing printer memory
To erase volatile memory or buffered data in your printer, turn off the printer.
To erase non‑volatile memory or individual settings, device and network settings, security settings, and embedded solutions, do the following:
1 From the home screen, touch Settings > Device > Maintenance > Out of Service Erase.
2 Select the Sanitize all information on nonvolatile memory check box, and then touch ERASE.
3 Follow the instructions on the display.
1 From the home screen, touch Settings > Device > Maintenance > Out of Service Erase.
2 Select the Sanitize all information on hard disk check box, and then touch ERASE.
3 Follow the instructions on the display.
1 From the home screen, touch Settings > Security > Disk Encryption > Start Encryption.
2 Follow the instructions on the display.
From the home screen, touch Settings > Device > Restore Factory Defaults > Restore Settings > Restore all settings > RESTORE > Start.
For more information, see “Erasing printer memory” on page 32.

Securing the printer 33
Your printer contains various types of memory that can store device and network settings, and user data.
Type of memory Description
Volatile memory Your printer uses standard random access memory (RAM) to temporarily buffer user data during simple print jobs.
Non-volatile memory Your printer may use two forms of non-volatile memory: EEPROM and NAND (flash memory). Both types are used to store the operating system, device settings, network information and bookmark settings, and embedded solutions.
Hard disk memory Some printers have a hard disk drive installed. The printer hard disk is designed for printer-specific functionality. This lets the printer retain buffered user data from complex print jobs, as well as form data, and font data.
Erase the content of any installed printer memory in the following circumstances:
In high‑security environments, it may be necessary to take additional steps to make sure that confidential data stored in the printer hard disk cannot be accessed when the printer—or its hard disk—is removed from your premises.

Maintaining the printer 34
The speaker volume will reset to default value after the session is logged out, when the printer wakes from Sleep or Hibernate mode, or after a power‑on reset.
1 From the control panel, navigate to:
Settings > Device > Preferences > Audio Feedback
2 Select the volume.
Headphones volume will reset to default value after the session is logged out, when the printer wakes from Sleep or Hibernate mode, or after a power‑on reset.
1 From the control panel, select Settings > Device > Accessibility > Headphone Volume.
2 Select the volume.
Connecting the printer to a wireless network using Wi‑Fi Protected Setup (WPS)
Before you begin, make sure that:
1 From the control panel, navigate to:
Settings > Network/Ports > Wireless > Wi‑Fi Protected Setup > Start Push Button Method
2 Follow the instructions on the display.

Maintaining the printer 35
1 From the control panel, navigate to:
Settings > Network/Ports > Wireless > Wi‑Fi Protected Setup > Start PIN Method
2 Copy the eight‑digit WPS PIN.
3 Open a Web browser, and then type the IP address of your access point in the address field.
4 Access the WPS settings. For more information, see the documentation that came with your access point.
5 Enter the eight‑digit PIN, and then save the changes.
1 Open the printers folder.
2 From the shortcut menu of the printer with the new ISP, open the printer properties.
3 Configure the port from the list.
4 Update the IP address.
5 Apply the changes.
1 From System Preferences in the Apple menu, navigate to the list of printers, and then select + > IP.
2 Type the IP address in the address field.
3 Apply the changes.
1 Set the parameters in the printer. a From the control panel, navigate to the menu for the port settings. b Locate the menu for the serial port settings, and then adjust the settings, if necessary.

Maintaining the printer 36
c Apply the changes.
2 From your computer, open the printers folder, and then select your printer.
3 Open the printer properties, and then select the COM port from the list.
4 Set the COM port parameters in Device Manager.
1 Turn off the printer, and then unplug the power cord from the electrical outlet.
2 Remove paper from the standard bin and multipurpose feeder.
3 Remove any dust, lint, and pieces of paper around the printer using a soft brush or vacuum.
4 Wipe the outside of the printer with a damp, soft, lint‑free cloth.
5 Connect the power cord to the electrical outlet, and then turn on the printer.

Maintaining the printer 37
To order supplies in the U.S., contact Lexmark at 1-800-539-6275 for information about Lexmark authorized supplies dealers in your area. In other countries or regions, go to www.lexmark.com or contact the place where you purchased the printer.
1 From the home screen, touch Status/Supplies.
2 Select the parts or supplies that you want to check.
Your Lexmark printer is designed to function best with genuine Lexmark parts and supplies. Use of third-party supplies or parts may affect the performance, reliability, or life of the printer and its imaging components. It can also affect warranty coverage. Damage caused by the use of third-party parts and supplies is not covered by the warranty. All life indicators are designed to function with Lexmark parts and supplies, and may deliver unpredictable results if third-party parts and supplies are used. Imaging component usage beyond the intended life may damage your Lexmark printer or its associated components.
European Economic Area (EEA+)
Rest of Asia Pacific (RoAP)
Rest of Europe, Middle East,
Australia and New Zealand
(ANZ)
Return Program toner cartridges1
Black 74C10K0 74C20K0 74C30K0 74C40K0 74C50K0 74C60K0
Cyan 74C10C0 74C20C0 74C30C0 74C40C0 74C50C0 74C60C0
Magenta 74C10M0 74C20M0 74C30M0 74C40M0 74C50M0 74C60M0
Yellow 74C10Y0 74C20Y0 74C30Y0 74C40Y0 74C50Y0 74C60Y0
High Yield Return Program toner cartridges
1 These Return Program toner cartridges are supported in CS720 and CS725.
2 These High Yield Return Program toner cartridges are supported only in CS725.

Maintaining the printer 38

1 These Return Program toner cartridges are supported in CS720 and CS725.
2 These High Yield Return Program toner cartridges are supported only in CS725.

* This toner cartridge is also supported in CS720.


Maintaining the printer 39



Waste toner bottle 74C0W00

CS72x fuser maintenance kit, type 00, 110–120 V 41X0554
CS72x fuser maintenance kit, type 01, 220–240 V 41X0556
CS72x fuser maintenance kit, type 02, 100 V 41X0552
Item Part number

Maintaining the printer 40
Replacing parts and supplies
Replacing the imaging unit
1 Open door B.




Item Part number · Transfer module 40X9929

Maintaining the printer 41
2 Remove the waste toner bottle.

3 Remove the imaging kit.


Maintaining the printer 42
4 Remove the black toner cartridge.


5 Remove the imaging unit.




6 Unpack the new imaging unit.
7 Insert the new imaging unit.



Maintaining the printer 43
8 Insert the black toner cartridge.


9 Insert the imaging kit.








Maintaining the printer 44
10 Insert the waste toner bottle.




11 Close door B.
1 Open door B.

Maintaining the printer 45
2 Remove the waste toner bottle.

3 Remove the imaging kit.


Maintaining the printer 46
4 Remove the toner cartridges.




5 Unpack the new imaging kit, and then remove the packing material.
6 Remove the black imaging unit.


7 Insert the black imaging unit into the new imaging kit.




Maintaining the printer 47
8 Insert the toner cartridges.




9 Insert the new imaging kit.

Maintaining the printer 48
10 Insert the waste toner bottle.
11 Close door B.
1 Open door B.

Maintaining the printer 49
2 Remove the toner cartridge.



3 Unpack the new toner cartridge.
4 Insert the new toner cartridge.


5 Close door B.

Maintaining the printer 50
1 Open door B.
2 Remove the waste toner bottle.






3 Unpack the new waste toner bottle.

Maintaining the printer 51
4 Insert the new waste toner bottle.
5 Close door B.
1 Turn off the printer, and then unplug the power cord from the electrical outlet.
2 Open doors A and D.


3 Remove the fuser.



4 Unpack the new fuser.

Maintaining the printer 52
5 Insert the new fuser.



6 Close doors D and A.
7 Connect the power cord to the electrical outlet, and then turn on the printer.
8 Reset the fuser maintenance counter.
For more information, see “Resetting the maintenance counter” on page 61.
Replacing the pick roller in the 550‑sheet tray
1 Turn off the printer, and then unplug the power cord from the electrical outlet.
2 Remove the tray.

Maintaining the printer 53
3 Remove the pick roller.




4 Unpack the new pick roller.

Maintaining the printer 54
5 Insert the new pick roller until it clicks into place.



6 Insert the tray.
7 Connect the power cord to the electrical outlet, and then turn on the printer.
1 Turn off the printer, and then unplug the power cord from the electrical outlet.
2 Open the multipurpose feeder.



Maintaining the printer 55
3 Remove the pick roller.




4 Unpack the new pick roller.
5 Insert the new pick roller until it clicks into place.




6 Close the multipurpose feeder.
7 Connect the power cord to the electrical outlet, and then turn on the printer.
1 Pull out the tray.



Maintaining the printer 56
2 Remove the separator pad.




3 Unpack the new separator pad.
4 Insert the new separator pad until it clicks into place.



5 Insert the tray.

Maintaining the printer 57
1 Turn off the printer, and then unplug the power cord from the electrical outlet.
2 Open door B.
3 Remove the waste toner bottle.





Maintaining the printer 58
4 Remove the imaging kit.






5 Open door A.



Maintaining the printer 59
6 Remove the transfer module.




7 Unpack the new transfer module, and then remove the packing material.
8 Insert the new transfer module.




9 Close door A.

Maintaining the printer 60
10 Insert the imaging kit.
11 Insert the waste toner bottle.
12 Close door B.
13 Connect the power cord to the electrical outlet, and then turn on the printer.
14 Reset the maintenance counter. For more information, see “Resetting the maintenance counter” on page 61.

Maintaining the printer 61
1 From the home screen, touch Settings > Device > Maintenance > Configuration Menu > Supply Usage And Counters.
2 Select Fuser Reset or ITM Reset.
For shipping instructions, go to http://support.lexmark.com or contact customer support.

Maintaining the printer 62
1 From the home screen, touch Settings > Device > Power Management > Eco‑Mode.
2 Select a setting.
1 From the home screen, touch Settings > Device > Power Management > Timeouts > Sleep Mode.
2 Enter the number of minutes the printer stays idle before it enters Sleep mode.
1 From the home screen, touch Settings > Device > Power Management > Timeouts > Hibernate Timeout.
2 Select the amount of time before the printer enters hibernate mode.
1 From the home screen, touch Settings > Device > Preferences > Screen Brightness.
2 Adjust the setting.
To return Lexmark products for recycling:
1 Go to www.lexmark.com/recycle.
2 Select the product you want to recycle.
Eco‑Mode

Maintaining the printer 63
Lexmark continually strives to minimize packaging. Less packaging helps to ensure that Lexmark printers are transported in the most efficient and environmentally sensitive manner and that there is less packaging to dispose of. These efficiencies result in fewer greenhouse emissions, energy savings, and natural resource savings. Lexmark also offers recycling of packaging components in some countries or regions. For more information, go to www.lexmark.com/recycle, and then choose your country or region. Information on available packaging recycling programs is included with the information on product recycling.
Lexmark cartons are 100% recyclable where corrugated recycling facilities exist. Facilities may not exist in your area.
The foam used in Lexmark packaging is recyclable where foam recycling facilities exist. Facilities may not exist in your area.
When you return a cartridge to Lexmark, you can reuse the box that the cartridge came in. Lexmark recycles the box.
The Lexmark Cartridge Collection Program allows you to return used cartridges for free to Lexmark for reuse or recycling. One hundred percent of the empty cartridges returned to Lexmark are either reused or demanufactured for recycling. The boxes used to return the cartridges are also recycled.
To return Lexmark cartridges for reuse or recycling, do the following:
1 Go to www.lexmark.com/recycle.
2 Select the product that you want to recycle.

Avoiding jams
Correct loading of paper Incorrect loading of paper


Clearing jams 64



Clearing jams 65

1 Pull out the tray.


2 Remove the jammed paper.


3 Insert the tray.
Clearing jams 66

1 Remove paper from the multipurpose feeder.
2 Pull out the tray.
3 Remove the jammed paper.

4 Insert the tray.
1 Remove the jammed paper.


2 Open doors A and D, and then remove any paper fragments.
Clearing jams 67




3 Close doors D and A.
1 Open door A.


2 Remove the jammed paper.
Clearing jams 68



3 Open the fuser access door.


4 Remove the jammed paper.
Clearing jams 69



5 Close door A.
1 Open door A.
Clearing jams 70

2 Open the duplex cover.



3 Remove the jammed paper.


4 Close the duplex cover and door A.
Clearing jams 71

Network connection problems
Step 1 Check if you are using a supported browser:
Go to step 2. Install a supported browser.
Is your browser supported?
Go to step 3. Type the correct printer IP address in the address field.
Make sure that the printer IP address is correct.
View the printer IP address:
Is the printer IP address correct?
Go to step 4. Turn on the printer.
Check if the printer is on.
Is the printer on?
Go to step 5. Contact your administrator.
Check if the network connection is working.
Is the network connection working?
Go to step 6. Secure the cable connections.
Make sure that the cable connections to the printer and print server are secure.
For more information, see the setup documentation that came with the printer.
Are the cable connections secure?

Go to step 7. Contact your administrator.
Check if the web proxy servers are disabled.
Are the web proxy servers disabled?
Step 7 Access the Embedded Web Server.
The problem is solved.
Contact customer support.
Did the Embedded Web Server open?
Go to step 2. The problem is solved.
Check if the flash drive is inserted into the front USB port.
Is the flash drive inserted into the front USB port?
Go to step 3. The problem is solved.
Check if the flash drive is supported. For more information, see “Supported flash drives and file types” on page 29
Does the error message still appear?
Contact customer support.
The problem is solved.
Check if the front USB port is disabled. For more information, see “Enabling the USB port” on page 73.
Does the error message still appear?
From the home screen, touch Settings > Network/Ports > USB > Enable USB Port.
1 From the home screen, touch Settings > Reports > Network > Network Setup Page.
2 Check the first section of the network setup page, and confirm that the status is connected.
If the status is not connected, then the LAN drop may be inactive, or the network cable may be unplugged or malfunctioning. Contact your administrator for assistance.

The problem is solved.
Go to step 2.
Turn off the printer, wait for about 10 seconds, and then turn it back on.
Does the internal option operate correctly?
Go to step 4. Go to step 3.
Print a menu settings page, and then check if the internal option appears in the Installed Features list.
Is the internal option listed in the menu settings page?
The problem is solved.
Go to step 4.
Check if the internal option is properly installed in the controller board.
a Turn off the printer, and then unplug the power cord from the
electrical outlet. b Make sure that the internal option is installed in the appropriate
connector in the controller board. c Connect the power cord to the electrical outlet, and then turn
on the printer.
Does the internal option operate correctly?
The problem is solved.
Contact customer support.
a Check if the internal option is available in the print driver.
Does the internal option operate correctly?

Go to step 3. Go to step 2.
Print a menu settings page, and then check if the internal solutions port (ISP) appears in the Installed Features list.
Is the ISP listed in the Installed Features list?
The problem is solved.
Go to step 3.
Remove, and then install the ISP. For more information, see “Installing an internal solutions port” on page 107.
Does the ISP operate correctly?
The problem is solved.
Contact customer support.
Check the cable and the ISP connection.
a Use the correct cable, and then make sure that it is securely
connected to the ISP. b Check if the ISP solution interface cable is securely connected
into the receptacle of the controller board.
Does the ISP operate correctly?
Go to step 3. Go to step 2.
Print a menu settings page, and then check if the parallel or serial interface card appears in the Installed Features list.
Is the parallel or serial interface card listed in the Installed Features list?
The problem is solved.
Go to step 3.
Remove, and then install the parallel or serial interface card. For more information, see “Installing an internal solutions port” on page 107.
Does the parallel or serial interface card operate correctly?
The problem is solved.
Contact customer support.
Check the connection between the cable and the parallel or serial interface card.
Does the parallel or serial interface card operate correctly?

Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
To correct this problem, purchase a cartridge with the correct region that matches the printer region, or purchase a worldwide cartridge.
Worldwide or Undefined region 0
North America (United States, Canada) 1
European Economic Area, Western Europe, Nordic countries, Switzerland 2
Rest of Europe, Middle East, Africa 5
Australia, New Zealand 6

The printer has detected a non‑Lexmark supply or part installed in the printer.
Your Lexmark printer is designed to function best with genuine Lexmark supplies and parts. Use of third- party supplies or parts may affect the performance, reliability, or life of the printer and its imaging components.
All life indicators are designed to function with Lexmark supplies and parts and may deliver unpredictable results if third-party supplies or parts are used. Imaging component usage beyond the intended life may damage your Lexmark printer or associated components.
To accept any and all of these risks and to proceed with the use of non-genuine supplies or parts in your printer, from the control panel, press and hold X and # simultaneously for 15 seconds.
If you do not want to accept these risks, then remove the third-party supply or part from your printer and install a genuine Lexmark supply or part. For more information, see “Using genuine Lexmark parts and supplies” on page 37.
If the printer does not print after pressing and holding X and # simultaneously for 15 seconds, then reset the supply usage counter.
1 From the control panel, navigate to:
Settings > Device > Maintenance > Configuration Menu > Supply Usage And Counters
2 Select the part or supply that you want to reset, and then select Start.
3 Read the warning message, and then select Continue.
4 Press and hold X and # simultaneously for 15 seconds to clear the message.
1 Use envelopes that have been stored in a dry environment.
Contact customer support.
The problem is solved.
Does the envelope seal when printing?

The problem is solved.
Go to step 2.
a From the home screen, touch Settings > Print > Layout >
Collate. b Set Collate to On.
c Print the document.
Are the pages collated correctly?
The problem is solved.
Go to step 3.
a From the document that you are trying to print, open the Print
dialog, and then select Collate. b Print the document.
Are the pages collated correctly?
The problem is solved.
Contact customer support.
a Reduce the number of pages to print. b Print the document.
Are the pages collated correctly?
Go to step 2. The problem is solved.
Move the paper guides in the tray to the correct position for the paper loaded.
Is the paper still curled?
Go to step 3. The problem is solved.
a Depending on your operating system, specify the paper type
and weight from the Printing Preferences or Print dialog.
Is the paper still curled?

Go to step 4. The problem is solved.
a Remove paper from the tray, and then turn it over. b Resend the print job.
Is the paper still curled?
Contact customer support.
The problem is solved.
a Load paper from a fresh package.
Is the paper still curled?
The problem is solved.
Go to step 2.
a Check if the trays contain paper of the same size and type. b Check if the paper guides are positioned correctly.
c Print the document.
Do the trays link correctly?
The problem is solved.
Contact customer support.
a From the home screen, touch Settings > Paper > Tray
Configuration > Paper Size/Type. b Set the paper size and type to match the paper loaded in the
linked trays. c Print the document.
Do the trays link correctly?
Try one or more of the following:
If the error occurs a second time, then:
1 Turn off the printer. 2 Unplug the power cord from the electrical outlet. 3 Remove the indicated tray. 4 Insert the tray.

5 Connect the power cord to the electrical outlet.
If the error occurs again, then:
1 Turn off the printer. 2 Unplug the power cord from the electrical outlet. 3 Remove the indicated tray. 4 Contact customer support. • From the control panel, select Continue to clear the message and resume printing.
Go to step 2. The problem is solved.
a Pull out the tray. b Check if the paper is loaded correctly.
Do paper jams still occur frequently?
Go to step 3. The problem is solved.
a From the Paper menu on the control panel, check if the printer
is detecting the correct paper size. b Resend the print job.
Do paper jams still occur frequently?
Contact customer support.
The problem is solved.
a Load paper from a fresh package. b Print the document.
Do paper jams still occur frequently?

1 From the home screen, touch Settings > Device > Notifications > Jam Content Recovery. 2 Select On or Auto. 3 Apply the changes.
The problem is solved.
Contact customer support.
Are the jammed pages reprinted?
The problem is solved.
Go to step 2.
a From the control panel, check if the documents appear in the
Held Jobs list.
Are the documents printed?
The problem is solved.
Go to step 3.
The print job may contain a formatting error or invalid data.
Are the documents printed?
The problem is solved.
Go to step 4.
If you are printing from the Internet, then the printer may be reading the multiple job titles as duplicates.
a Open the Printing Preferences dialog. b From the Print and Hold section, select Keep duplicate
documents. c Enter a PIN. d Resend the print job.
a Save and name each job differently. b Send the job individually.
Are the documents printed?

The problem is solved.
Go to step 5.
a Delete some held jobs to free up printer memory. b Resend the print job.
Are the documents printed?
The problem is solved.
Contact customer support.
a Add printer memory. b Resend the print job.
Are the documents printed?
Go to step 2. The problem is solved.
a Make sure that the printer is not in Eco‑Mode and Quiet Mode. b Print the document.
Is the printer printing slow?
Go to step 3. The problem is solved.
a Depending on your operating system, specify the paper type
from the Printing Preferences or Print dialog.
Is the printer printing slow?
Go to step 4. The problem is solved.
a Reduce the number of pages to print. b Print the document.
Is the printer printing slow?
Go to step 5. The problem is solved.
a Remove held jobs. b Print the document.
Is the printer printing slow?

Go to step 6. The problem is solved.
a Connect the printer cable securely to the printer and the
computer, print server, option, or other network device. b Print the document.
Is the printer printing slow?
Go to step 7. The problem is solved.
a From the Quality menu on the control panel, set the Print
Resolution to 4800CQ. b Print the document.
Is the printer printing slow?
Go to step 8. The problem is solved.
a Make sure that the printer is not overheating.
Is the printer printing slow?
Contact customer support.
The problem is solved.
a Add more printer memory. b Print the document.
Is the printer printing slow?
The problem is solved.
Go to step 2.
a From the document you are trying to print, open the Print
dialog, and then check if you have selected the correct printer. b Resend the print job.
Is the document printed?
The problem is solved.
Go to step 3.
a Check if the printer is on. b Resolve any error messages that appear on the display.
c Resend the print job.
Is the document printed?

The problem is solved.
Go to step 4.
a Check if the ports are working and if the cables are securely
connected to the computer and the printer.
For more information, see the setup documentation that came with the printer. b Resend the print job.
Is the document printed?
The problem is solved.
Go to step 5.
a Turn off the printer, wait for about 10 seconds, and then turn it
back on. b Resend the print job.
Is the document printed?
The problem is solved.
Contact customer support.
a Remove, and then reinstall the printer software.
Is the document printed?


Go to step 2. The problem is solved.
a Remove, and then reinstall the imaging unit or imaging kit.
Is the printer still printing blank or white pages?
Contact customer support.
The problem is solved.
a Replace the imaging unit or imaging kit.
Is the printer still printing blank or white pages?
Go to step 2. The problem is solved.
a From the Quality menu on the control panel, select Color
Adjust. b Resend the print job.
Is the print still too dark?

Go to step 3. The problem is solved.
a Depending on your operating system, reduce the toner
darkness from the Printing Preferences or Print dialog.
Is the print still too dark?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type,
texture, and weight from the Printing Preferences or Print dialog.
Is the print still too dark?
Step 4 Make sure that the paper has no texture or rough finishes.
Change the texture settings to match the paper you are printing on.
Go to step 5.
Are you printing on textured or rough paper?
Go to step 6. The problem is solved.
a Load paper from a fresh package.
Is the print still too dark?
Contact customer support.
The problem is solved.
a Remove, and then reinstall the waste toner bottle. b From the Quality menu on the control panel, select Color
Adjust. c Resend the print job.
Is the print still too dark?


a Load the tray with the correct paper type and weight. b Resend the print job.
a Depending on your operating system, specify the paper type
and weight from the Printing Preferences or Print dialog.
a From the Quality menu on the control panel, select Color
ABCDE
ABCDE ABCDE
Troubleshooting 87 · Leading edge · Trailing edge

Go to step 2. The problem is solved.
a From the home screen, touch Settings > Print > Quality. b Adjust the toner darkness.
c Print the document.
Does gray background still appear on prints?
Go to step 3. The problem is solved.
a From the home screen, touch Settings > Print > Quality >
Advanced Imaging > Color Adjust. b Start the process.
c Print the document.
Does gray background still appear on prints?
Contact customer support.
The problem is solved.
a Remove, and then reinstall the imaging unit or imaging kit.
Does gray background still appear on prints?
ABCDE ABCDE ABCDE
Go to step 2. The problem is solved.
a Depending on your operating system, specify the tray or feeder
from the Printing Preferences or Print dialog. b Resend the print job.
Do horizontal dark lines still appear on prints?

Go to step 3. The problem is solved.
a Depending on your operating system, specify the paper type
and weight from the Printing Preferences or from Print dialog.
Do horizontal dark lines still appear on prints?
Go to step 4. The problem is solved.
a Load paper from a fresh package.
Do horizontal dark lines still appear on prints?
Contact customer support.
The problem is solved.
a Remove, and then reinstall the imaging unit or imaging kit.
Do horizontal dark lines still appear on prints?

Go to step 2. The problem is solved.
a Depending on your operating system, specify the paper type
and weight from the Printing Preferences or Print dialog.
Do horizontal white lines still appear on prints?
Go to step 3. The problem is solved.
a Load the specified tray or feeder with the recommended paper
type. b Resend the print job.
Do horizontal white lines still appear on prints?
Contact customer support.
The problem is solved.
a Remove, and then reinstall the imaging unit or imaging kit.
Do horizontal white lines still appear on prints?
ABCD ABCD ABCD

The problem is solved.
Go to step 2.
a Squeeze and slide the paper guides to the correct position for
the size of the paper you are loading. b Resend the print job.
Are the margins correct?
The problem is solved.
Go to step 3.
a From the Paper menu on the control panel, check if the printer
is detecting the correct paper size. b Resend the print job.
Are the margins correct?
The problem is solved.
Contact customer support.
a Depending on your operating system, specify the paper size
from the Printing Preferences or Print dialog.
Are the margins correct?

a Check if the printer supports the fonts that are installed on your
Contact customer support.
The problem is solved.
computer.
1 From the control panel, touch: Settings > Reports > Print > Print Fonts 2 Select PCL Fonts or PS Fonts. b If the font is not supported, then install a supported font. For
more information, contact your administrator. c Resend the print job.
Do prints still contain jagged or uneven characters?
Go to step 2. The problem is solved.
a From the Quality menu on the control panel, select Color
Adjust. b Resend the print job.
Is the print still too light?
Go to step 3. The problem is solved.
a Depending on your operating system, increase the toner
darkness from the Printing Preferences or Print dialog.
Is the print still too light?

Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type,
texture, and weight from the Printing Preferences or Print dialog.
Is the print still too light?
Change the texture settings to match the paper you are printing on.
Go to step 5.
Make sure that the paper has no texture or rough finishes.
Are you printing on textured or rough paper?
Go to step 6. The problem is solved.
a Load paper from a fresh package.
Is the print still too light?
Go to step 7. The problem is solved.
a Remove, and then reinstall the waste toner bottle. b From the Quality menu on the control panel, select Color
Adjust.
Is the print still too light?
Contact customer support.
The problem is solved.
Remove, and then reinstall the imaging kit.
Is the print still too light?
ABC DEF

Step 1 Check the printer for leaked toner contamination.
Go to step 2. Contact customer support.
Is the printer free of leaked toner?
Go to step 4. Go to step 3.
a From the home screen, touch Settings > Device > Preferences. b Check if the paper type and size settings match the paper type
and size set in the tray.
Do the settings match?
Go to step 4. The problem is solved.
a Change the paper size and type in the Paper menu or adjust
the size settings in the tray. b Print the document.
Is the print still mottled?
Go to step 5. The problem is solved.
a Replace the textured or rough paper loaded in the tray with
plain paper. b Print the document.
Is the print still mottled?
Contact customer support.
The problem is solved.
a Replace the imaging unit or imaging kit.
Is the print still mottled?
) ) ABCDE
ABCDE ABCDE

Go to step 2. The problem is solved.
a Remove the tray. b Remove the paper, and then load paper from a fresh package.
the size of the paper you are loading. d Insert the tray. e Resend the print job.
Is the print still crooked or skewed?
Contact customer support.
The problem is solved.
a Check if you are printing on a supported paper. b Resend the print job.
Is the print still crooked or skewed?
Go to step 2. Go to step 3.
a Print the quality sample pages.
From the home screen, touch Settings > Troubleshooting > Basic Print Quality Samples. b Determine how many colors have defects.
Is only one color affected?

Take note of the distance, and then contact customer support or your service representative.
The problem is solved.
a Using the Maintenance Defect Ruler, measure the distance
between the repeating defects on the affected color page. b Replace the supply item that matches the measurement on the
affected color page.
Imaging kit or imaging unit
Do the defects still appear?
Take note of the distance, and then contact customer support or your service representative.
The problem is solved.
a Using the Maintenance Defect Ruler, measure the distance
between the defects on the affected color page. b Replace the supply item that matches the measurement on the
affected color page.
Do the defects still appear?



a Remove, and then reinstall the imaging unit or imaging kit.
Is the printer still printing solid color or black images?

a Move the paper guides in the tray to the correct position for the
a Depending on your operating system, specify the paper size
Troubleshooting 97


a Remove, and then reinstall the imaging unit or imaging kit.

1 Depending on your operating system, specify the paper type, texture, and weight from the Printing Preferences or Print dialog.
Troubleshooting 98


Replace the imaging unit or imaging kit, and then resend the print job.

a Remove, and then reinstall the imaging unit or imaging kit.
Do vertical dark lines or streaks still appear on prints?
Troubleshooting 99 · Leading edge · Trailing edge

a Remove, and then reinstall the imaging unit or imaging kit.
Contact customer support.
The problem is solved.
Do vertical white lines still appear on prints?
The problem is solved.
Go to step 2.
Connect the power cord to the electrical outlet.
Is the printer responding?
Turn on the switch or reset the breaker.
Go to step 3.
Check if the electrical outlet is turned off by a switch or breaker.
Is the electrical outlet turned off by a switch or breaker?
Go to step 4. Turn on the printer.
Check if the printer is on.
Is the printer on?
Press the power button to wake the printer.
Go to step 5.
Check if the printer is in sleep or hibernate mode.
Is the printer in sleep or hibernate mode?
Step 5 Check if the cables connecting the printer and the computer are inserted in the correct ports.
Go to step 6. Make sure to match the following:
Are the cables inserted in the correct ports?

The problem is solved
Go to step 7.
Turn off the printer, reinstall the hardware options, and then turn it back on.
For more information, see the documentation that came with the option.
Is the printer responding?
The problem is solved
Go to step 8.
Install the correct print driver.
Is the printer responding?
The problem is solved.
Contact customer support.
Turn off the printer, wait for about 10 seconds, and then turn it back on.
Is the printer responding?
Go to step 2. Load the correct paper size and paper type.
a Check if you are printing on the correct paper. b Print the document.
Is the document printed on the correct paper?
The problem is solved.
Go to step 3.
a Depending on your operating system, specify the paper size
and paper type from the Printing Preferences or Print dialog.
Is the document printed from the correct tray or on the correct paper?
The problem is solved.
Contact customer support.
a Check if the trays are not linked.
For more information, see “Linking trays” on page 25. b Print the document.
Is the document printed from the correct tray?

1 From the home screen, touch Settings > Print > Quality.
2 Adjust the toner darkness.
3 Apply the changes.
1 From the home screen, touch Settings > Print > Quality > Advanced Imaging > Color Correction > Manual.
2 From the Advanced Imaging menu, select Color Correction Content.
3 Choose the appropriate color conversion setting.
Object type Color conversion tables
RGB Text RGB Graphics
What is RGB color?
RGB color is a method of describing colors by indicating the amount of red, green, or blue used to produce a certain color. Red, green, and blue light can be added in various amounts to produce a large range of colors observed in nature. Computer screens, scanners, and digital cameras use this method to display colors.

What is CMYK color?
CMYK color is a method of describing colors by indicating the amount of cyan, magenta, yellow, and black used to reproduce a particular color. Cyan, magenta, yellow, and black inks or toners can be printed in various amounts to produce a large range of colors observed in nature. Printing presses, inkjet printers, and color laser printers create colors in this manner.
How is color specified in a document to be printed?
Software programs are used to specify and modify the document color using RGB or CMYK color combinations. For more information, see the software program Help topics.
How does the printer know what color to print?
When printing a document, information describing the type and color of each object is sent to the printer and is passed through color conversion tables. Color is translated into the appropriate amounts of cyan, magenta, yellow, and black toner used to produce the color you want. The object information determines the application of color conversion tables. For example, it is possible to apply one type of color conversion table to text while applying a different color conversion table to photographic images.
What is manual color correction?
When manual color correction is enabled, the printer employs user‑selected color conversion tables to process objects. Manual color correction settings are specific to the type of object being printed (text, graphics, or images). It is also specific to how the color of the object is specified in the software program (RGB or CMYK combinations). To apply a different color conversion table manually, see “Modifying the colors in printed output” on page 102.
If the software program does not specify colors with RGB or CMYK combinations, then manual color correction is not useful. It is also not effective if the software program or the computer operating system controls the adjustment of colors. In most situations, setting the Color Correction to Auto generates preferred colors for the documents.
How can I match a particular color (such as a corporate logo)?
From the printer Quality menu, nine types of Color Samples sets are available. These sets are also available from the Color Samples page of the Embedded Web Server. Selecting any sample set generates multiple‑page prints consisting of hundreds of colored boxes. Each box contains a CMYK or RGB combination, depending on the table selected. The observed color of each box is obtained by passing the CMYK or RGB combination labeled on the box through the selected color conversion table.
By examining Color Samples sets, you can identify the box with color closest to the color being matched. The color combination labeled on the box can then be used for modifying the color of the object in a software program. For more information, see the software program Help topics. Manual color correction may be necessary to use the selected color conversion table for the particular object.
Selecting which Color Samples set to use for a particular color‑matching problem depends on:
If the software program does not specify colors with RGB or CMYK combinations, then the Color Samples pages are not useful. Additionally, some software programs adjust the RGB or CMYK combinations specified in the program through color management. In these situations, the printed color may not be an exact match of the Color Samples pages.
Troubleshooting 103

Adjust the color balance.
The problem is solved.
Contact customer support.
a From the home screen, touch Settings > Print > Quality >
Advanced Imaging > Color Balance. b Adjust the setting.
c Resend the print job.
Does the print still appear tinted?
Before contacting customer support, make sure to have the following information:
Go to http://support.lexmark.com to receive e‑mail or chat support, or browse through the library of manuals, support documentation, drivers, and other downloads.
Technical support via telephone is also available. In the U.S. or Canada, call 1-800-539-6275. For other countries or regions, go to http://support.lexmark.com.
Troubleshooting 104 · Action No Yes

Upgrading and migrating 105
Hardware
Module) – IEEE 1284‑B Parallel Card – RS‑232C Serial Card
CAUTION—SHOCK HAZARD: To avoid the risk of electrical shock, if you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Turn off the printer, and then unplug the power cord from the electrical outlet.
2 Using a flat‑head screwdriver, remove the controller board access cover.

Upgrading and migrating 106





3 Unpack the memory card.
4 Insert the memory card until it clicks into place.



Upgrading and migrating 107
5 Reattach the access cover.




6 Connect the power cord to the electrical outlet, and then turn on the printer.
CAUTION—SHOCK HAZARD: To avoid the risk of electrical shock, if you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Turn off the printer, and then unplug the power cord from the electrical outlet.
2 Using a flat‑head screwdriver, remove the controller board access cover.

Upgrading and migrating 108
3 Unpack the internal solutions port (ISP) kit.


2 Mounting bracket · 3 Thumbscrews · 4 Housing

Upgrading and migrating 109
5 ISP extended cable
4 Install the ISP into its housing.





Upgrading and migrating 110
5 Attach the housing to the controller board access cover.






Upgrading and migrating 111
6 Connect the ISP extended cable to the ISP connector in the controller board.

7 Reattach the controller board access cover.

8 Connect the power cord to the electrical outlet, and then turn on the printer.

Upgrading and migrating 112
CAUTION—SHOCK HAZARD: To avoid the risk of electrical shock, if you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Turn off the printer, and then unplug the power cord from the electrical outlet.
2 Using a flat‑head screwdriver, remove the controller board access cover.
3 Unpack the optional card.

Upgrading and migrating 113
4 Push the card firmly into place.





Upgrading and migrating 114
5 Reattach the access cover.
6 Connect the power cord to the electrical outlet, and then turn on the printer.
CAUTION—SHOCK HAZARD: To avoid the risk of electrical shock, if you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Turn off the printer, and then unplug the power cord from the electrical outlet.
2 Using a flat‑head screwdriver, remove the controller board access cover.

Upgrading and migrating 115
3 Unpack the hard disk.
4 Attach the hard disk to the controller board.






Upgrading and migrating 116
5 Open door B.
6 Open door C.




Upgrading and migrating 117
7 Secure the hard disk to the printer using the thumbscrews.


8 Close doors C and B.
9 Reattach the controller board access cover.

10 Connect the power cord to the electrical outlet, and then turn on the printer.

Upgrading and migrating 118
CAUTION—SHOCK HAZARD: To avoid the risk of electrical shock, if you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet, and then from the printer.
3 Unpack the optional tray, and then remove all packing material.
4 Align the printer with the optional tray, and then lower the printer until it clicks into place.



5 Connect the power cord to the printer, and then to the electrical outlet.
6 Turn on the printer.
Add the tray in the print driver to make it available for print jobs. For more information, see “Adding available options in the print driver” on page 119.

Upgrading and migrating 119
2 Run the installer, and then follow the instructions on the computer screen.
3 For Macintosh users, add the printer.
1 Open the printers folder.
3 Navigate to the Configuration tab, and then select Update Now ‑ Ask Printer.
4 Apply the changes.
1 From System Preferences in the Apple menu, navigate to your printer, and then select Options & Supplies.
2 Navigate to the list of hardware options, and then add any installed options.
3 Apply the changes.
You can export the configuration settings of your printer into a text file, and then import the file to apply the settings to other printers.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Export or import a configuration file for one or multiple applications.

Upgrading and migrating 120
a From the Embedded Web Server, click Apps > the application that you want > Configure. b Click Export or Import.
a From the Embedded Web Server, click Export Configuration or Import Configuration. b Follow the instructions on the screen.
Some applications require a minimum device firmware level to operate correctly.
For more information on updating the device firmware, contact your Lexmark representative.
1 From the Embedded Web Server, click Settings > Device > Update Firmware.
2 Browse to locate the required flash file.
3 Apply the changes.

Product name:
Lexmark CS720de, CS720dte, CS725de, CS725dte, CS727de, CS728de
Machine type:
Model(s):
The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.
References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.
For Lexmark technical support, visit http://support.lexmark.com.
For information on supplies and downloads, visit www.lexmark.com.
© 2017 Lexmark International, Inc.
All rights reserved.
The Software Program and any related documentation are "Commercial Items," as that term is defined in 48 C.F.R. 2.101, "Computer Software" and "Commercial Computer Software Documentation," as such terms are used in 48 C.F.R. 12.212 or 48 C.F.R. 227.7202, as applicable. Consistent with 48 C.F.R. 12.212 or 48 C.F.R. 227.7202-1 through 227.7207-4, as applicable, the Commercial Computer Software and Commercial Software Documentation are licensed to the U.S. Government end users (a) only as Commercial Items and (b) with only those rights as are granted to all other end users pursuant to the terms and conditions herein.
5028, 7528 · 135, 630, 576 · June 2017

All licensing notices associated with this product can be viewed from the CD:\NOTICES directory of the installation software CD.
Lexmark, the Lexmark logo, and MarkNet are trademarks or registered trademarks of Lexmark International, Inc. in the United States and/or other countries.
Google Cloud Print and Google Chrome are trademarks of Google Inc.
Macintosh, the Mac logo, and Safari are trademarks of Apple Inc.
Microsoft, Windows, and Internet Explorer are either registered trademarks or trademarks of the Microsoft group of companies in the United States and other countries.
Mopria®, the Mopria® logo, and the Mopria® Alliance logo are registered trademarks and service marks of Mopria Alliance, Inc. in the United States and other countries. Unauthorized use is strictly prohibited.
PCL® is a registered trademark of the Hewlett-Packard Company. PCL is Hewlett-Packard Company’s designation of a set of printer commands (language) and functions included in its printer products. This printer is intended to be compatible with the PCL language. This means the printer recognizes PCL commands used in various application programs, and that the printer emulates the functions corresponding to the commands.
PostScript is a registered trademark of Adobe Systems Incorporated in the United States and/or other countries.
All other trademarks are the property of their respective owners.
AirPrint and the AirPrint logo are trademarks of Apple, Inc.
The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.
1-meter average sound pressure, dBA
Printing One-sided: 51 (CS720, CS727); 53 (CS725, CS728) Two‑sided: 53 (CS720, CS727); 55 (CS725, CS728)
Values are subject to change. See www.lexmark.com for current values.
Ready 15

This symbol identifies static-sensitive parts. Do not touch the areas near these symbols without first touching a metal surface in an area away from the symbol.
Operating temperature and relative humidity 10 to 32.2°C (50 to 90°F) and 15 to 80% RH 15.3 to 32.2°C (60 to 90°F) and 8 to 15% RH Maximum wet bulb temperature: 22.8°C (73°F)
Shipping temperature -40 to 43.3°C (-40 to 110°F)
Storage temperature and relative humidity 1 to 35°C (34 to 95°F)
8 to 80% RH
The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR, Chapter I, Subchapter J for Class I (1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements of IEC 60825-1: 2014.
Class I laser products are not considered to be hazardous. The printer contains internally a Class IIIb (3b) AlGaInP laser that is nominally 15 milliwatts operating in the wavelength region of 650–670 nanometers and enclosed in a non-serviceable printhead assembly. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service conditions.
A laser notice label may be affixed to this printer as shown:

NEBEZPEČÍ - Když jsou vyjmuty kazety a je odblokována pojistka, ze zařízení je vysíláno neviditelné laserové záření. Nevystavujte se působení laserového paprsku. FARE - Usynlig laserstråling, når patroner fjernes, og spærreanordningen er slået fra. Undgå at blive udsat for laserstrålen.
VAARA - Näkymätöntä lasersäteilyä on varottava, kun värikasetit on poistettu ja lukitus on auki. Vältä lasersäteelle altistumista.
VESZÉLY – Nem látható lézersugárzás fordulhat elő a patronok eltávolításakor és a zárószerkezet felbontásakor. Kerülje a lézersugárnak való kitettséget. PERICOLO - Emissione di radiazioni laser invisibili durante la rimozione delle cartucce e del blocco. Evitare l´esposizione al raggio laser.
FARE – Usynlig laserstråling når kassettene tas ut og sperren er satt ut av spill. Unngå eksponering for laserstrålen. NIEBEZPIECZEŃSTWO - niewidzialne promieniowanie laserowe podczas usuwania kaset i blokady. Należy unikać naświetlenia promieniem lasera.
ОПАСНО! Невидимое лазерное излучение при извлеченных картриджах и снятии блокировки. Избегайте воздействия лазерных лучей. Pozor – Nebezpečenstvo neviditeľného laserového žiarenia pri odobratých kazetách a odblokovanej poistke. Nevystavujte sa lúčom.
FARA – Osynlig laserstrålning när patroner tas ur och spärrmekanismen är upphävd. Undvik exponering för laserstrålen. 危险 - 当移除碳粉盒及互锁失效时会产生看不见的激光辐射,请避免暴露在激光光束下。
危險 - 移除碳粉匣與安全連續開關失效時會產生看不見的雷射輻射。請避免曝露在雷射光束下。 危険 - カートリッジが取り外され、内部ロックが無効になると、見えないレーザー光が放射されます。 このレーザー光に当たらないようにしてください。




Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.