
User's Guide
Machine type(s):
Model(s):


Connect the power cord directly to an appropriately rated and properly grounded electrical outlet that is near the product and easily accessible.
Do not place or use this product near water or wet locations.
This product uses a printing process that heats the print media, and the heat may cause the media to release emissions. You must understand the section in your operating instructions that discusses the guidelines for selecting print media to avoid the possibility of harmful emissions.
Use only the power cord provided with this product or the manufacturer's authorized replacement.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
Safety information 6

This product is designed, tested, and approved to meet strict global safety standards with the use of specific manufacturer's components. The safety features of some parts may not always be obvious. The manufacturer is not responsible for the use of other replacement parts.
CAUTION—POTENTIAL INJURY: Do not cut, twist, bind, crush, or place heavy objects on the power cord. Do not subject the power cord to abrasion or stress. Do not pinch the power cord between objects such as furniture and walls. If any of these things happen, a risk of fire or electrical shock results. Inspect the power cord regularly for signs of such problems. Remove the power cord from the electrical outlet before inspecting it.
Refer service or repairs, other than those described in the user documentation, to a service representative.
SAVE THESE INSTRUCTIONS.
Safety information 7

Learning about the printer 8
Finding information about the printer

Learning about the printer 9
When selecting a location for the printer, leave enough room to open trays, covers, and doors. If you plan to install any options, then leave enough room for them also. It is important to:

Learning about the printer 10


Learning about the printer 11

4 5 6 3 4 5 3 4
If the printer is installed on a network, then you can use the Embedded Web Server to do the following:
To access the Embedded Web Server for your printer:
– An IP address appears as four sets of numbers separated by periods, such as 123.123.123.123.

Learning about the printer 12
– If you are using a proxy server, then temporarily disable it to load the Web page correctly.
2 Open a Web browser, and then type the printer IP address in the address field.
3 Press Enter.
The Embedded Web Server page appears.

Understanding the printer control panel 13
Using the printer control panel


3 Keypad Enter numbers, letters, or symbols on the printer.
4 Sleep button Enable Sleep mode or Hibernate mode.
6 Indicator light Check the status of the printer.
7 USB port Connect a USB a flash drive to the printer.
The colors of the Sleep button and indicator lights on the printer control panel signify a certain printer status or condition.

Understanding the printer control panel 14
Indicator light Printer status
Off The printer is off or in Hibernate mode.
Blinking green The printer is warming up, processing data, or printing.
Solid green The printer is on, but idle.
Blinking red The printer requires user intervention.
Sleep button light Printer status
Off The printer is off, idle or in Ready state.
Solid amber The printer is in Sleep mode.
Blinking amber The printer is entering or waking from Hibernate mode.
Blinking amber for 0.1 second, then goes completely off for 1.9 seconds in a slow, pulsing pattern
The printer is in Hibernate mode.
When the printer is turned on, the display shows a basic screen, referred to as the home screen. Use the home screen buttons and icons to initiate an action.
1 2 3 4

5 6 7 8
1 Change Language Change the primary language of the printer.
2 Bookmarks Create, organize, and save a set of bookmarks (URLs) into a tree view of folders and file links.
3 Held Jobs Display all current held jobs.
Touch To

Understanding the printer control panel 15
4 USB View, select, or print photos and documents from a flash drive.
5 Menus Access printer menus.
8 Tips View a context‑sensitive help information.
This may also appear on the home screen:
Search Held Jobs Search current held jobs.
Jobs by user Access print jobs saved by user.
Profiles and Solutions Access profiles and solutions.
If an attendance message affects a function, then this icon appears and the red indicator light blinks.
The IP address of your printer is located at the top left corner of the home screen and appears as four sets of numbers separated by periods. You can use the IP address when accessing the Embedded Web Server to view and remotely configure printer settings even when you are not physically near the printer.

Understanding the printer control panel 16

1 Radio button Select or clear an item.
2 Up arrow Scroll up.
3 Down arrow Scroll down.
4 Accept button Save a setting.
Return to the home screen.
Open a context-sensitive Help dialog on the printer control panel.
Scroll to the left.
Scroll to the right.
Touch the To · Touch To

Setting up and using the home screen applications 17
1 In the Run dialog box, type cmd to open the command prompt.
2 Type ipconfig, and then look for the IP address.
1 From System Preferences in the Apple menu, select Network.
2 Select your connection type, and then click Advanced > TCP/IP.
3 Look for the IP address.
You can find the printer IP address:
The Embedded Web Server is the printer Web page that lets you view and remotely configure printer settings even when you are not physically near the printer.
2 Open a Web browser, and then type the printer IP address in the address field.

Setting up and using the home screen applications 18
3 Press Enter.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Do one or more of the following: • Show or hide the icons of basic printer functions. a Click Settings > General Settings > Home screen customization. b Select the check boxes to specify which icons appear on the home screen.
Your printer comes with preinstalled home screen applications. Before you can use these applications, you must first activate and set up these applications using the Embedded Web Server. For more information on accessing the Embedded Web Server, see “Accessing the Embedded Web Server” on page 17.
For more information on configuring and using the home screen applications, do the following:
1 Go to http://support.lexmark.com.
3 Click the Manuals tab, and then select the document for the home screen application.

The application lets you customize the background and idle screen of your printer home screen.
Icon Description

Setting up and using the home screen applications 19
1 From the home screen, navigate to:
Change Background > select background to use

Streamline work processes by letting you quickly find and print frequently used online forms directly from the printer home screen.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Apps > Apps Management > Forms and Favorites.
3 Click Add, and then customize the settings.
4 Click Apply.
To use the application, touch Forms and Favorites on the printer home screen, and then navigate through form categories, or search for forms based on a form number, name, or description.
2 Touch · Use To

Setting up and using the home screen applications 20
The application lets you easily manage energy consumption, noise, toner, and paper usage settings to help reduce the environmental impact of your printer.
This application enables you to interact with the printer control panel even when you are not physically near the network printer. From your computer, you can view the printer status, release held print jobs, create bookmarks, and do other print-related tasks.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Remote Operator Panel Settings.
3 Select the Enable check box, and then customize the settings.
4 Click Submit.
To use the application, click Remote Operator Panel > Launch VNC Applet.
You can export configuration settings into a text file, and then import the file to apply the settings to other printers.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Export or import a configuration file for one or multiple applications.
a Navigate to:
Settings > Apps > Apps Management > select an application > Configure b Export or import the configuration file.
Icon Description

Setting up and using the home screen applications 21
a Click Settings > Import/Export. b Export or import a configuration file.

Additional printer setup 22
Installing internal options
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
You can customize your printer connectivity and memory capacity by adding optional cards.
* This internal option is available only in CS510 printer model.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.

Additional printer setup 23
1 At the back of the printer, turn the screws counterclockwise to remove them.

2 Slightly open the controller board access cover, and then shift to the right to remove it.

3 Locate the appropriate connector on the controller board.

Additional printer setup 24

1 Flash memory or font card connector
2 Printer hard disk connector
3 Memory card connector
4 Reattach the cover.


Additional printer setup 25
5 Turn the screws clockwise to lock the cover.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Access the controller board.
For more information, see “Accessing the controller board” on page 22.
2 Unpack the memory card.

Additional printer setup 26
3 Align the notch (1) on the memory card with the ridge (2) on the connector.

4 Push the memory card straight into the connector, and then push the card toward the controller board wall until it clicks into place.

5 Close the controller board access cover.

Additional printer setup 27
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Access the controller board.
For more information, see “Accessing the controller board” on page 22.
2 Unpack the optional card.
3 Holding the card by its sides, align the plastic pins (1) on the card with the holes (2) on the controller board.



Additional printer setup 28
4 Push the card firmly into place as shown in the illustration.

5 Close the controller board access door.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.

Additional printer setup 29
1 Access the controller board.
For more information, see “Accessing the controller board” on page 22.
2 Unpack the printer hard disk.
3 Remove the screws attached to the printer hard disk mounting bracket, and then remove the bracket.

4 Locate the appropriate connector on the controller board.


Additional printer setup 30
5 Align the standoffs of the printer hard disk to the holes in the controller board, and then press the printer hard disk down until the standoffs are in place.

6 Insert the plug of the printer hard disk interface cable into the receptacle of the controller board.

7 Close the controller board access cover.

Additional printer setup 31
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Access the controller board.
For more information, see “Accessing the controller board” on page 22.
2 Unplug the printer hard disk interface cable from the controller board, leaving the cable attached to the printer hard disk. To unplug the cable, squeeze the paddle at the plug of the interface cable to disengage the latch before pulling the cable out.
3 Remove the printer hard disk by pulling it away from the controller board.

Additional printer setup 32
4 Set aside the printer hard disk.
5 Close the controller board access cover.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
Install the printer and any optional tray in the following order:
The printer supports two optional input sources: a 550‑sheet tray and a 650‑sheet duo tray (Tray 2) with an integrated multipurpose feeder.

Additional printer setup 33
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Unpack the optional tray, and then remove all packing material and the dust cover.

2 Label the trays with the supplied tray number labels from the top down.
3 Place the tray near the printer.
4 Align the 650‑sheet duo tray with the optional 550‑sheet tray, and then lower it into place.


Additional printer setup 34
5 Align the printer with the 650‑sheet duo tray, and then lower the printer into place.

6 Install the dust covers.


1 Obtain a copy of the software installer package.
2 Run the installer, and then follow the instructions on the computer screen.

Additional printer setup 35
3 For Macintosh users, add the printer.
1 Open the printers folder, and then select your printer.
2 Open the printer properties, and then add or manually install any options.
3 Apply the changes.
1 From System Preferences in the Apple menu, navigate to your printer, and then select Options & Supplies > Driver.
2 Add any installed hardware options.
3 Apply the changes.
Make sure to match the following:

1 Rear USB port Attach a keyboard to the printer.
2 USB printer port Connect the printer to a computer.
3 Ethernet port Connect the printer to a network.
4 USB wireless port Attach an optional wireless network adapter.
Use the To

Additional printer setup 36
5 Security lock port Lock the system controller board.
6 Printer power cord socket Connect the printer to a properly grounded electrical outlet.
To configure your printer to connect to an Ethernet network, organize the following information before you begin:
You will need an Ethernet cable to connect the printer to the network and an available port where the printer can physically connect to the network. Use a new network cable when possible to avoid potential problems caused by a damaged cable.
Make sure you have the following information before setting up the printer on a wireless network:
Some ad hoc networks will also require the automatic setting. Check with your system support person if you are not sure which channel to select.
Use the To

Additional printer setup 37
If your network uses more than one WEP key, then enter up to four in the provided spaces. Select the key currently in use on the network by selecting the default WEP transmit key. or – WPA or WPA2 preshared key or passphrase
WPA includes encryption as an additional layer of security. The choices are AES or TKIP. Encryption must be set for the same type on the router and on the printer, or the printer will not be able to communicate on the network. – 802.1X–RADIUS
If you are installing the printer on an 802.1X network, then you may need the following:
If your wireless network does not use any type of security, then you will not have any security information.
– If you do not know the SSID of the network that your computer is connected to, then launch the wireless utility
of the computer network adapter, and then look for the network name. If you cannot find the SSID or the security information for your network, then see the documentation that came with the access point, or contact your system support person. – To find the WPA/WPA2 preshared key/passphrase for the wireless network, see the documentation that came
with the access point, see the Web page associated with the access point, or consult your system support person.
Before you begin, make sure that:
> Network/Ports > Active NIC > Auto >
1 From the printer control panel, navigate to:
> Network/Ports > Network [x] > Network [x] Setup > Wireless > Wireless Connection Setup
2 Select a wireless connection setup.

Additional printer setup 38
Search for networks Show available wireless connections.
Enter a network name Manually type the SSID.
Wi‑Fi Protected Setup Connect the printer to a wireless network using Wi‑Fi Protected Setup.
3 Follow the instructions on the printer display.
Connecting the printer to a wireless network using Wi‑Fi Protected Setup
Before you begin, make sure that:
1 From the printer control panel, navigate to:
> Network/Ports > Network [x] > Network [x] Setup > Wireless > Wireless Connection Setup > Wi‑Fi Protected Setup > Start Push Button Method
2 Follow the instructions on the printer display.
1 From the printer control panel, navigate to:
> Network/Ports > Network [x] > Network [x] Setup > Wireless > Wireless Connection Setup > Wi‑Fi Protected Setup > Start PIN Method
2 Copy the eight‑digit WPS PIN.
3 Open a Web browser, and then type the IP address of your access point in the address field.
4 Access the WPS settings. For more information, see the documentation that came with your access point.
5 Enter the eight‑digit PIN, and then save the setting.
Use To

Additional printer setup 39
Before you begin, make sure that:
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Network/Ports > Wireless.
3 Modify the settings to match the settings of your access point (wireless router).
4 Click Submit.
5 Turn off the printer, and then disconnect the Ethernet cable. Then wait for at least five seconds, and then turn the printer back on.
6 To verify if your printer is connected to the network, print a network setup page. Then in the Network Card [x] section, see if the status is “Connected”.
For more information, see the “Verifying printer setup” section of the User’s Guide.
When all hardware and software options are installed and the printer is turned on, verify that the printer is set up correctly by printing the following:
From the home screen, navigate to:
> Reports > Menu Settings Page

Additional printer setup 40
If the printer is attached to a network, then print a network setup page to verify the network connection. This page also provides important information that aids network printing configuration.
1 From the home screen, navigate to:
> Reports > Network Setup Page
2 Check the first section of the network setup page, and confirm that the status is Connected.
If the status is Not Connected, then the LAN drop may not be active, or the network cable may be malfunctioning. Consult a system support person for a solution, and then print another network setup page.

Loading paper and specialty media 41
Proper selection and loading of media can improve how reliably documents print. For more information, see “Avoiding jams” on page 151 and “Storing paper” on page 58.
From the home screen navigate to:
> Paper Menu > Paper Size/Type > select a tray > select the paper size or type >
The Universal paper size is a user‑defined setting that lets you print on paper sizes that are not preset in the printer menus.
1 From the home screen, navigate to:
> Paper Menu > Universal Setup > Units of Measure > select a unit of measure
2 Touch Portrait Width or Portrait Height.
3 Select the width or height, and then touch
The printer has one 250-sheet tray (Tray 1) with an integrated manual feeder. The 250-sheet tray, the 650-sheet duo tray, and the 550-sheet tray support the same paper sizes and types and are loaded in the same way.
1 Pull out the tray completely.

Loading paper and specialty media 42

2 If the paper is longer than letter‑size paper, then squeeze and then slide the length guide at the back of the tray to extend it.

3 Squeeze, and then slide the length guide tab to the correct position for the size of the paper being loaded.



Loading paper and specialty media 43
4 Squeeze, and then slide the width guide tab to the correct position for the size of the paper being loaded.


5 Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.


Loading paper and specialty media 44
6 Load the paper stack with the recommended printable side faceup.

7 Place the paper guides securely against the edges of the paper.
8 Insert the tray.

9 From the printer control panel, set the paper size and paper type in the Paper menu to match the paper loaded in the tray.
The 650‑sheet duo tray (Tray 2) consists of a 550‑sheet tray and an integrated 100‑sheet multipurpose feeder. The tray is loaded in the same way as the 250‑sheet tray and the optional 550‑sheet tray, and supports the same paper types and sizes. The only differences are the look of the guide tabs and the location of the paper size indicators.

Loading paper and specialty media 45

1 Length guide tab
2 Paper size indicator
3 Width guide tab
1 Push the multipurpose feeder latch to the left.



Loading paper and specialty media 46
2 Open the multipurpose feeder.

3 Pull the multipurpose feeder extender.

4 Prepare the paper for loading. • Flex the sheets of paper back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.


Loading paper and specialty media 47
5 Locate the maximum paper fill indicator and tab.


6 Load the paper, and then adjust the width guide to lightly touch the edge of the paper stack. • Load paper, card stock, and transparencies with the recommended printable side facedown and the top edge entering the printer first.


Loading paper and specialty media 48

7 From the printer control panel, set the paper size and type in the Paper menu to match the paper loaded in the tray.
The standard 250‑sheet tray has an integrated manual feeder that can be used to print on different types of paper one sheet at a time.
One‑sided printing using a letterhead Two‑sided printing using a letterhead

ABC

Loading paper and specialty media 49

2 Feed paper into the manual feeder only to the point where its leading edge can contact the paper guides.
3 Adjust the paper guides to the width of the paper loaded.

The printer links trays when the specified paper size and type are the same. When a linked tray becomes empty, paper feeds from the next linked tray. To prevent trays from linking, assign a unique custom paper type name.
1 Open a Web browser, and then type the printer IP address in the address field.

Loading paper and specialty media 50
2 Click Settings > Paper Menu.
4 Click Submit.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu > Custom Names.
3 Select a custom name, and then type a custom paper type name.
4 Click Submit.
5 Click Custom Types, and then verify if the new custom paper type name has replaced the custom name.
1 From the home screen, navigate to:
> Paper Menu > Custom Names
2 Select a custom name, and then type a custom paper type name.
4 Touch Custom Types, and then verify that the new custom paper type name has replaced the custom name.
Assign a custom paper type name to a tray when linking or unlinking trays.
1 Open a Web browser, and then type the printer IP address in the address field.
3 Touch

Loading paper and specialty media 51
2 Click Settings > Paper Menu > Custom Types.
3 Select a custom paper type name, and then select a paper type
4 Click Submit.
1 From the home screen, navigate to:
> Paper Menu > Custom Types
2 Select a custom paper type name, and then select a paper type
3 Touch

Paper and specialty media guide 52
Source Printing Printable side Paper orientation
One‑sided Faceup Load the sheet with the top edge entering the printer first.

Two‑sided Facedown Load the sheet with the bottom edge entering the printer first.
Trays · Trays

Paper and specialty media guide 53
Source Printing Printable side Paper orientation
One‑sided Facedown Load the sheet with the top edge entering the printer first.

Two‑sided Faceup Load the sheet with the bottom edge entering the printer first.
One‑sided Facedown Load the sheet with the top edge entering the printer first.
Two‑sided Faceup Load the sheet with the bottom edge entering the printer first.


Paper and specialty media guide 54
Print a test page on the transparencies being considered for use before buying large quantities.

Paper and specialty media guide 55
Card stock is heavy, single‑ply specialty media. Many of its variable characteristics, such as moisture content, thickness, and texture, can significantly affect print quality.
Select the correct paper or specialty media to reduce printing problems. For the best print quality, try a sample of the paper or specialty media before buying large quantities.
The following paper characteristics affect print quality and reliability. Consider these characteristics when evaluating new paper stock.
The printer trays can automatically feed paper weights up to 176‑g/m2 (47‑lb) bond grain long paper. The multipurpose feeder can automatically feed paper weights up to 176‑g/m2 (47‑lb) bond grain long paper. Paper lighter than 60 g/m2 (16 lb) might not be stiff enough to feed properly, causing jams. For best performance, use 75‑g/m2 (20‑lb) bond grain long paper. For paper smaller than 182 x 257 mm (7.2 x 10.1 inches), we recommend 90 g/m2 (24 lb) or heavier paper.
Curl is the tendency for paper to curl at its edges. Excessive curl can cause paper feeding problems. Curl can occur after the paper passes through the printer, where it is exposed to high temperatures. Storing paper unwrapped in hot, humid, cold, or dry conditions, even in the trays, can contribute to paper curling prior to printing and can cause feeding problems.

Paper and specialty media guide 56
Paper smoothness directly affects print quality. If paper is too rough, then toner cannot fuse to it properly. If paper is too smooth, then it can cause paper feeding or print quality issues. Always use paper between 100 and 300 Sheffield points; smoothness between 150 and 250 Sheffield points produces the best print quality.
The amount of moisture in paper affects both print quality and the ability of the printer to feed the paper correctly. Leave paper in its original wrapper until it is time to use it. This limits the exposure of paper to moisture changes that can degrade its performance.
Store paper in its original wrapper in the same environment as the printer for 24 to 48 hours before printing. Extend the time to several days if the storage or transportation environment is very different from the printer environment. Thick paper may also require a longer conditioning period.
Grain refers to the alignment of the paper fibers in a sheet of paper. Grain is either grain long, running the length of the paper, or grain short, running the width of the paper.
For 60–90‑g/m2 (16–24‑lb) bond paper, grain long paper is recommended.
Most high‑quality xerographic paper is made from 100% chemically treated pulped wood. This content provides the paper with a high degree of stability resulting in fewer paper feeding problems and better print quality. Paper containing fibers such as cotton can negatively affect paper handling.
The following paper types are not recommended for use with the printer:
Using the appropriate paper prevents jams and helps ensure trouble‑free printing.

Paper and specialty media guide 57
To help avoid paper jams and poor print quality:
Use these guidelines when selecting preprinted forms and letterhead:
Use papers printed with heat‑resistant inks designed for use in xerographic copiers. The ink must be able to withstand temperatures up to 230°C (446°F) without melting or releasing hazardous emissions. Use inks that are not affected by the resin in toner. Inks that are oxidation‑set or oil‑based generally meet these requirements; latex inks might not. When in doubt, contact the paper supplier.
Preprinted papers such as letterhead must be able to withstand temperatures up to 230°C (446°F) without melting or releasing hazardous emissions.
As an environmentally conscious company, Lexmark supports the use of recycled office paper produced specifically for use in laser (electrophotographic) printers. In 1998, Lexmark presented to the US government a study demonstrating that recycled paper produced by major mills in the US fed as well as non-recycled paper. However, no blanket statement can be made that all recycled paper will feed well.
Lexmark consistently tests its printers with recycled paper (20–100% post-consumer waste) and a variety of test paper from around the world, using chamber tests for different temperature and humidity conditions. Lexmark has found no reason to discourage the use of today's recycled office papers, but generally the following property guidelines apply to recycled paper.
Recycled paper, paper of lower weight (

Paper and specialty media guide 58
Use these paper storage guidelines to help avoid jams and uneven print quality:
The following tables provide information on standard and optional paper sources and the sizes, types, and weights of paper they support.
Note: Your printer model may have a 650‑sheet duo tray, which consists of a 550‑sheet tray and an integrated 100‑sheet multipurpose feeder. The 550‑sheet tray of the 650‑sheet duo tray supports the same paper sizes as the optional 550‑sheet tray. The integrated multipurpose feeder supports different paper sizes, types, and weights.
650‑sheet duo tray 550‑sheet tray
Paper size and dimension
Standard 250‑sheet tray Manual
550‑sheet tray Multipurpose
1
210 x 297 mm (8.3 x 11.7 in.)
1 2 1 2 X
148 x 210 mm (5.83 x 8.3 in.)
X X 1 X X
105 x 148 mm (4.1 x 5.8 in.)
1 The paper source supports paper size without size sensing.
2 Universal is only supported in the standard 250and optional 550sheet tray if the paper size is from 148 x 215.9 mm (5.83 x 8.5 inches) to 215.9 x 355.6 mm (8.5 x 14 inches).
3Universal is only supported in the multipurpose feeder and manual feeder if the paper size is from 76.2 x 127 mm (3 x 5 inches) to 215.9 x 359.9 mm (8.5 x 14.17 inches).
4Universal is only supported in duplex mode if the width is between 210 mm (8.27 inches) and 215.9 mm (8.5 inches) and length is between 279.4 mm (11 inches) and 355.6 mm (14 inches).

Paper and specialty media guide 59
Paper size and dimension
Standard 250‑sheet tray Manual
650‑sheet duo tray 550‑sheet tray
550‑sheet tray Multipurpose
1 1 1 1 X
182 x 257 mm (7.2 x 10.1 in.)
1
216 x 279 mm (8.5 x 11 in.)
Legal 216 x 356 mm (8.5 x 14 in.)
1
184 x 267 mm (7.3 x 10.5 in.)
1
216 x 340 mm (8.5 x 13.4 in.)
1
216 x 330 mm (8.5 x 13 in.)
140 x 216 mm (5.5 x 8.5 in.)
76 x 127 mm (3 x 5 in.) to 216 x 356 mm (8.5 x 14 in.)
1,2 1,2 1,2 4
148 x 210 mm (5.8 x 8.3 in) to 216 x 356 mm (8.5 x 14 in).
7 3/4 Envelope (Monarch)
98 x 191 mm (3.9 x 7.5 in.)
1 The paper source supports paper size without size sensing.
2 Universal is only supported in the standard 250and optional 550sheet tray if the paper size is from 148 x 215.9 mm (5.83 x 8.5 inches) to 215.9 x 355.6 mm (8.5 x 14 inches).
3Universal is only supported in the multipurpose feeder and manual feeder if the paper size is from 76.2 x 127 mm (3 x 5 inches) to 215.9 x 359.9 mm (8.5 x 14.17 inches).
4Universal is only supported in duplex mode if the width is between 210 mm (8.27 inches) and 215.9 mm (8.5 inches) and length is between 279.4 mm (11 inches) and 355.6 mm (14 inches).

Paper and specialty media guide 60
Paper size and dimension
Standard 250‑sheet tray Manual
650‑sheet duo tray 550‑sheet tray
550‑sheet tray Multipurpose
98 x 225 mm (3.9 x 8.9 in.)
105 x 241 mm (4.1 x 9.5 in.)
DL Envelope 110 x 220 mm (4.3 x 8.7 in.)
X X 1 X X
162 x 229 mm (6.4 x 9 in.)
176 x 250 mm (6.9 x 9.8 in.)
98 x 162 mm (3.9 x 6.3 in.) up to 176 x 250 mm (6.9 x 9.8 in.)
1 The paper source supports paper size without size sensing.
2 Universal is only supported in the standard 250and optional 550sheet tray if the paper size is from 148 x 215.9 mm (5.83 x 8.5 inches) to 215.9 x 355.6 mm (8.5 x 14 inches).
3Universal is only supported in the multipurpose feeder and manual feeder if the paper size is from 76.2 x 127 mm (3 x 5 inches) to 215.9 x 359.9 mm (8.5 x 14.17 inches).
4Universal is only supported in duplex mode if the width is between 210 mm (8.27 inches) and 215.9 mm (8.5 inches) and length is between 279.4 mm (11 inches) and 355.6 mm (14 inches).

Paper and specialty media guide 61

Paper type 250‑sheet tray Manual feeder 650‑sheet duo tray 550‑sheet tray Duplex mode

Printing forms and a document
Use Forms and Favorites to quickly and easily access frequently used forms or other information that is regularly printed. Before you can use this application, first set it up on the printer. For more information, see “Setting up Forms and Favorites” on page 19.
1 From the home screen, navigate to:
Forms and Favorites > select the form from the list > enter the number of copies > adjust other settings
2 Apply the changes.
1 From the printer control panel, set the paper type and size to match the paper loaded.
2 Send the print job:
a With a document open, click File > Print. b Click Properties, Preferences, Options, or Setup.
c Adjust the settings, if necessary. d Click OK > Print.
a Customize the settings in the Page Setup dialog:
1 With a document open, choose File > Page Setup. 2 Choose a paper size or create a custom size to match the paper loaded. 3 Click OK. b Customize the settings in the Print dialog:
1 With a document open, choose File > Print. If necessary, click the disclosure triangle to see more options. 2 From the print options pop‑up menus, adjust the settings, if necessary.
From the home screen, navigate to:
Printing 62

> Settings > Print Settings > Quality Menu > Print Mode > Black Only >
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Print Settings > Quality Menu > Toner Darkness.
3 Adjust the setting, and then click Submit.
1 From the home screen, navigate to:
> Settings > Print Settings > Quality Menu > Toner Darkness
2 Adjust the setting, and then touch
Max Speed and Max Yield let you choose between a faster print speed or a higher toner yield. Max Yield is the factory default setting.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Print Settings > Setup Menu.
3 From the Printer Usage list, select Max Speed or Max Yield.
4 Click Submit.
Printing 63

1 From the home screen, navigate to:
> Settings > Print Settings > Setup Menu
2 From the Printer Usage list, select Max Speed or Max Yield.
3 Touch Submit.
1 Insert a flash drive into the USB port.

Printing 64

2 From the printer control panel, touch the document you want to print.
3 Touch the arrows to specify the number of copies for printing, and then touch Print.
Recommended flash drives File type
Documents:
Images:
To download a compatible mobile printing application, visit www.lexmark.com/mobile.
Printing 65

1 From the home screen, navigate to:
> Security > Confidential Print > select a print job type
Max Invalid PIN Limit the number of times an invalid PIN can be entered.
Confidential Job Expiration Hold print jobs in the computer until you enter the PIN from the printer control panel.
Repeat Job Expiration Print and store print jobs in the printer memory.
Verify Job Expiration Print one copy of a print job and hold the remaining copies. It lets you examine if the first copy is satisfactory or not. The print job is automatically deleted from the printer memory when all copies are printed.
Reserve Job Expiration Store print jobs for printing at a later time.
1 With a document open, click File > Print.
2 Click Properties, Preferences, Options, or Setup.
3 Click Print and Hold.
Printing 66 · Use To · 2 Touch

4 Select the print job type (Confidential, Repeat, Reserve, or Verify), and then assign a user name. For a confidential print job, also enter a four‑digit PIN.
5 Click OK or Print.
1 With a document open, choose File > Print.
If necessary, click the disclosure triangle to see more options.
2 From the print options or Copies & Pages pop‑up menu, choose Job Routing.
3 Select the print job type (Confidential, Repeat, Reserve, or Verify), and then assign a user name. For a confidential print job, also enter a four‑digit PIN.
4 Click OK or Print.
1 From the home screen, navigate to:
> Reports > Print Fonts
2 Touch PCL Fonts or PostScript Fonts.
A directory list shows the resources stored in a flash memory or on the printer hard disk.
From the home screen, navigate to:
> Reports > Print Directory
Printing 67

1 From the printer control panel, touch Cancel Job or press
on the keypad.
2 Touch the print job you want to cancel, and then touch Delete Selected Jobs.
on the keypad, then touch Resume to return to the home screen.
1 Open the printers folder, and then select your printer.
2 From the print queue, select the print job you want to cancel, and then delete it.
1 From System Preferences in the Apple menu, navigate to your printer.
2 From the print queue, select the print job you want to cancel, and then delete it.
Printing 68

Understanding the printer menus 69
Menus list
Supplies Paper Menu Reports Network/Ports
Standard Network or Network [x]
Substitute Size Paper Texture
Network [x] Setup Page
Waste Toner Bottle Black or Color Imaging Kit
Profiles List Print Fonts
Security Settings Help Option Card Menu
Erase Temporary Data Files
Set Date and Time
1 This menu item appears only when a 650-sheet duo tray is attached.
Cyan Cartridge View the status of the toner cartridges, which can be any of the following:
Early Warning Low Invalid Near End of Life Replace Missing Defective OK Unsupported

Understanding the printer menus 70
View the status of the waste toner bottle.
Near Full Replace Missing OK
View the status of the imaging kit.
OK Replace Black Imaging Kit Replace Color Imaging Kit
View the status of the maintenance kit.
Set a default paper source for all print jobs.
Tray [x] Multipurpose Feeder Manual Paper Manual Envelope
Specify the size of the paper loaded in each tray.
A4 A5 JIS‑B5 Letter Legal Executive Oficio (Mexico) Folio Universal

Understanding the printer menus 71
Specify the type of the paper loaded in each tray.
Plain Paper Card Stock Transparency Recycled Glossy Labels Bond Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x]
Specify the size of the paper loaded in the multipurpose feeder.
A4 A5 A6 JIS B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal 7 3/4 Envelope 9 Envelope 10 Envelope DL Envelope C5 Envelope B5 Envelope Other Envelope
Use To · Tray [x] Type · Multipurpose Feeder Size

Understanding the printer menus 72
Specify the type of the paper loaded in the multipurpose feeder.
Plain Paper Card Stock Transparency Recycled Glossy Labels Bond Envelope Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x]
Specify the size of the paper being manually loaded.
A4 A5 A6 JIS B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal
Specify the type of the paper being manually loaded.
Plain Paper Card Stock Transparency Recycled Glossy Labels Bond Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x]

Understanding the printer menus 73
Specify the size of the envelope being manually loaded.
7 3/4 Envelope 9 Envelope 10 Envelope DL Envelope C5 Envelope B5 Envelope Other Envelope
Specify the type of the envelope being manually loaded.
Envelope Custom Type [x]
Determine when the printer selects paper from the multipurpose feeder.
Substitute a specified paper size if the requested paper size is not available.
Off Statement/A5 Letter/A4 All Listed
Specify the relative texture of the plain paper loaded.

Understanding the printer menus 74
Specify the relative texture of the card stock loaded.
Specify the relative texture of the transparencies loaded.
Specify the relative texture of the recycled paper loaded.
Specify the relative texture of the glossy paper loaded.
Specify the relative texture of the heavy glossy paper loaded.
Specify the relative texture of the labels loaded.
Specify the relative texture of the bond paper loaded.
Specify the relative texture of the envelopes loaded.
Specify the relative texture of the letterhead loaded.
Specify the relative texture of the preprinted paper loaded.

Understanding the printer menus 75
Specify the relative texture of the colored paper loaded.
Specify the relative texture of the light paper loaded.
Specify the relative texture of the heavy paper loaded.
Specify the relative texture of the cotton paper loaded.
Specify the relative texture of the custom paper loaded.
Specify the relative weight of the plain paper loaded.
Specify the relative weight of the card stock loaded.
Specify the relative weight of the transparencies loaded.
Specify the relative weight of the recycled paper loaded.

Understanding the printer menus 76
Specify the relative weight of the glossy paper loaded.
Specify the relative weight of the heavy glossy paper loaded.
Specify the relative weight of the labels loaded.
Specify the relative weight of the bond paper loaded.
Specify the relative weight of the envelope loaded.
Specify the relative weight of the rough envelope loaded.
Specify the relative weight of the letterhead loaded.
Specify the relative weight of the preprinted paper loaded.
Specify the relative weight of the colored paper loaded.
Specify that the relative weight of the paper loaded is light.
Specify that the relative weight of the paper loaded is heavy.

Understanding the printer menus 77
Specify the relative weight of the rough or cotton paper loaded.
Specify the relative weight of the custom paper loaded.
Determine and set two‑sided printing for all print jobs that specify Cardstock as the paper type.
Determine and set two‑sided printing for all print jobs that specify Recycled as the paper type.
Determine and set two‑sided printing for all print jobs that specify Glossy as the paper type.
Determine and set two‑sided printing for all print jobs that specify Heavy Glossy as the paper type.
Determine and set two‑sided printing for all print jobs that specify Labels as the paper type.
Determine and set two‑sided printing for all print jobs that specify Bond as the paper type.
Determine and set two‑sided printing for all print jobs that specify Letterhead as the paper type.
Determine and set two‑sided printing for all print jobs that specify Preprinted as the paper type.
Determine and set two‑sided printing for all print jobs that specify Colored as the paper type.

Understanding the printer menus 78
Determine and set two‑sided printing for all print jobs that specify Light as the paper type.
Determine and set two‑sided printing for all print jobs that specify Heavy as the paper type.
Determine and set two‑sided printing for all print jobs that specify Rough/Cotton as the paper type.
Determine and set two‑sided printing for all print jobs that specify Custom [x] as the paper type.
Associate a paper or specialty media type with a factory default Custom Type [x] name or a user‑defined custom name created in the Embedded Web Server or MarkVisionTM Professional.
Paper Card Stock Transparency Glossy Rough/Cotton Labels Envelope
Specify a paper type when Recycled is selected.
Paper Card Stock Transparency Glossy Rough/Cotton Labels Envelope
Custom Name [x] Specify a custom name for a paper type. This name replaces Custom Type [x] in the printer menus.

Understanding the printer menus 79
Identify the units of measure.
Set the width for portrait orientation.
3–8.5 inches 76–216 mm
Set the width for portrait orientation.
3–14.17 inches 76–360 mm
Menu Settings Page Print a report on the current printer menu settings. The report also contains information about the status of the supplies and a list of hardware options that are successfully installed.
Device Statistics Print a report containing printer statistics, such as supply information and number of printed pages.
Network Setup Page Print a report containing information about the network settings of the printer.
Network [x] Setup Page Print a report containing information about the network settings of the printer.
Profiles List Print a list of profiles stored in the printer.
![Page 80 of the Lexmark CS510 user manual — Standard Network or Network [x] menu](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/page-80.webp?w=400)
Understanding the printer menus 80
Print a report of all the fonts available for the printer language currently set in the printer.
PCL Fonts PostScript Fonts
Print Directory Print a list of all the resources stored in an optional flash memory card or printer hard disk.
Print demo files that are available in the firmware, the flash option, and the disk option.
Demo Page [list of available demo pages]
Asset Report Print a report containing asset information, including the printer serial number and model name. The report contains text and UPC bar codes that can be scanned into an asset database.
Event Log Summary Print a summary of logged events.
Allow the printer to connect to a network.
Auto [list of available network cards]
Reduce power consumption when the printer receives no data from the Ethernet network.

Understanding the printer menus 81
Set the printer to automatically switch to PCL emulation when a print job requires it, regardless of the default printer language.
Set the printer to automatically switch to PS emulation when a print job requires it, regardless of the default printer language.
Set the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol.
Set the size of the network input buffer.
Auto 3KB to [maximum size allowed]
Temporarily store print jobs in the printer hard disk before printing. This menu only appears when a formatted disk is installed.
Set the printer to process Macintosh binary PostScript print jobs.

Understanding the printer menus 82
Standard Network Setup OR Network [x] Setup
Show and set the printer network settings.
Reports Network Card TCP/IP IPv6 Wireless AppleTalk
To access the menu, navigate to either of the following:
Print Setup Page Print a report containing information about the network printer settings, such as the TCP/IP address.
To access the menu, navigate to either of the following:
View the connection status of the wireless network adapter.
View Card Speed View the speed of an active wireless network adapter.
Reduce power consumption when the printer receives no data from the Ethernet network.
View the network addresses.
0, 10–225 seconds Set the amount of time it takes for a network print job to be canceled.

Understanding the printer menus 83
Allow the printer to print a banner page.
To access the menu, navigate to either of the following:
Set Hostname Set the current TCP/IP host name.
IP Address View or change the current TCP/IP address.
Netmask View or change the current TCP/IP netmask.
Gateway View or change the current TCP/IP gateway.
Specify the DHCP address and parameter assignment.
Specify the RARP address assignment setting.
Specify the BOOTP address assignment setting.
Specify the Zero Configuration Networking setting.
Enable the built-in FTP server, which lets you send files to the printer using File Transfer Protocol.
Enable the built-in Web server (Embedded Web Server). When enabled, the printer can be monitored and managed remotely using a Web browser.
WINS Server Address View or change the current WINS server address.

Understanding the printer menus 84
View or change the current DDNS setting.
View or change the current mDNS setting.
DNS Server Address View or change the current DNS server address.
Backup DNS Server Address [x] View or change the current DNS server address.
View or change the current HTTPS setting.
To access the menu, navigate to either of the following:
Enable IPv6 in the printer.
Specify whether or not the wireless network adapter accepts the automatic IPv6 address configuration entries provided by a router.
View Hostname Set the host name.
Enable DHCPv6 in the printer.
To access the menu, navigate to:
Network/Ports > Network [x] > Network [x] Setup > Wireless

Understanding the printer menus 85
Wi‑Fi Protected Setup
Establish a wireless network and enable network security.
Start Push Button Method Start PIN Method
Enable/Disable WPS Auto‑detection
Automatically detect the connection method that an access point with WPS uses—Start Push Button Method or Start PIN Method.
Specify the network mode.
Specify the wireless standard for the wireless network.
802.11b/g 802.11b/g/n
Choose Network Select an available network for the printer to use.
View Signal Quality View the quality of the wireless connection.
View Security Mode View the encryption method for the wireless network.
To access the menu, navigate to any of the following:
Enable or disable AppleTalk support.
View Name Show the assigned AppleTalk name.
View Address Show the assigned AppleTalk address.

Understanding the printer menus 86
Provide a list of AppleTalk zones available on the network.
[list of zones available on the network]
Set the printer to automatically switch to PCL emulation when a print job received through a USB port requires it, regardless of the default printer language.
Set the printer to automatically switch to PS emulation when a print job received through a USB port requires it, regardless of the default printer language.
Set the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol.

Understanding the printer menus 87
Set the size of the USB input buffer.
Disabled Auto 3K to [maximum size allowed]
Temporarily store print jobs in the printer hard disk before printing.
Set the printer to process Macintosh binary PostScript print jobs.
Set the network address information for an external print server.
yyy.yyy.yyy.yyy
Set the netmask information for an external print server.
yyy.yyy.yyy.yyy
Set the gateway information for an external print server.
yyy.yyy.yyy.yyy

Understanding the printer menus 88
Primary SMTP Gateway Specify SMTP server gateway and port information.
Secondary SMTP Gateway Port
5–30 Specify the amount of time in seconds before the server stops trying to send an e‑mail.
Reply Address Specify a reply address of up to 128 characters in the e-mail sent by the printer.
Set the printer to use SSL for increased security when connecting to the SMTP server.
Specify the type of user authentication required for scan to e‑mail privileges.
No authentication required Login/Plain CRAM‑MD5 Digest‑MD5 NTLM Kerberos 5
Device‑Initiated E‑mail
Specify what credentials will be used when communicating to the SMTP server.
None Use Device SMTP Credentials
User‑Initiated E‑mail
None Use Device SMTP Credentials Use Session User ID and Password Use Session E‑mail address and Password Prompt user

Understanding the printer menus 89
Limit the number and time frames of failed login attempts from the printer control panel before all users are locked out.
Login failures Failure time frame Lockout time Panel Login Timeout Remote Login Timeout
1–16 Limit the digit length of the PIN.
Limit the number of times an invalid PIN can be entered.
Limit the amount of time a confidential print job stays in the printer before it is deleted.
Off 1 hour 4 hours 24 hours 1 week

Understanding the printer menus 90
Set a time limit on how long the printer stores print jobs.
Off 1 hour 4 hours 24 hours 1 week
Set a time limit on how long the printer stores print jobs needing verification.
Off 1 hour 4 hours 24 hours 1 week
Set a time limit on how long the printer stores print jobs for printing at a later time.
Off 1 hour 4 hours 24 hours 1 week
Erase Temporary Data Files deletes only print job data on the printer hard disk that are not currently in use by the file system. All permanent data on the printer hard disk are preserved, such as downloaded fonts, macros, and held jobs.
Specify the mode for erasing temporary data files.
Mark all disk space used by a previous print job. This method does not permit the file system to reuse this space until it has been cleared.
Single pass Multiple pass

Understanding the printer menus 91
Export Log Let an authorized user export the audit log.
Specify whether or not audit logs are deleted.
Specify how and whether or not audit logs are created.
Yes No Enable Remote Syslog
No Yes Remote Syslog Facility
0–23 Severity of Events to Log
Current Date and Time View the current date and time settings for the printer.
Manually Set Date and Time Enter the date and time.
Time Zone Select the time zone.
Set the printer to use the applicable daylight saving time (DST) start and end times associated with the printer Time Zone setting.
Enable Network Time Protocol, which synchronizes the clocks of devices on a network.

Understanding the printer menus 92
Set the default printer language.
PCL Emulation PS Emulation
Determine if print jobs are removed from the print queue when they require unavailable printer options or custom settings. These print jobs are stored in a separate print queue, so other jobs print normally. When the missing information or options are obtained, the stored jobs print.
Set the logical and physical printable area.
Normal Fit To Page Whole Page
Set color toner use in printing.
Max Yield Max Speed

Understanding the printer menus 93
Set the printer to print text and graphics using only the black toner cartridge.
Set the storage location for downloads.
Specify how the printer handles temporary downloads, such as fonts and macros stored in the RAM, when the printer receives a job that requires more memory than is available.
Specify the order in which held and confidential jobs are printed .
Alphabetical Oldest First Newest First

Understanding the printer menus 94
Set the language of the text appearing on the display.
English Francais Deutsch Italiano Espanol Dansk Norsk Nederlands Svenska Portugues Suomi Russian Polski Greek Magyar Turkce Cesky Simplified Chinese Traditional Chinese Korean Japanese
View the estimates of the supplies on the control panel, Embedded Web Server, menu settings, and device statistics reports.
Show estimates Do not show estimates
Minimize the use of energy, paper, or specialty media.
Off Energy Energy/Paper Paper
Minimize the printer noise.
Run the setup wizard.

Understanding the printer menus 95
Specify a language and custom key information for the display keyboard.
English Francais Francais Canadien Deutsch Italiano Espanol Greek Dansk Norsk Nederlands Svenska Suomi Portugues Russian Polski Swiss German Swiss French Korean Magyar Turkce Cesky Simplified Chinese Traditional Chinese Japanese Custom Key [x]
Specify the unit of measurement for paper sizes.
U.S. Metric

Understanding the printer menus 96
Specify what is displayed on the upper corners of the home screen.
Left Side Right Side Custom Text [x]
For Left side and Right side, select from the following options:
None IP Address Hostname Contact Name Location Date/Time mDNS/DDNS Service Name Zero Configuration Name Custom Text [x] Model Name
Customize the displayed information for the supplies.
Black Toner Cyan Toner Magenta Toner Yellow Toner Waste Toner Bottle Fuser Transfer Module
Select from the following options:
Do not display Display Message to display

Understanding the printer menus 97
Customize the displayed information for certain menus.
Paper Jam Load Paper Service Errors
Select from the following options:
Yes No Message to display
Change the icons that appear on the home screen.
Change Language Search Held Jobs Held Jobs USB Drive Profiles and Apps Bookmarks Jobs by User Forms and Favorites Background and Idle Screen Eco-Settings
For each icon, select from the following options:
Display Do Not display
Format the date.
MM‑DD‑YYYY DD‑MM‑YYYY YYYY‑MM‑DD
Format the time.
12 hour A.M./P.M. 24 hour clock
20–100 Specify the brightness of the display.
Set the audio volume for the buttons.

Understanding the printer menus 98
Specify whether bookmarks are displayed from the Held Jobs area.
Web Page Refresh Rate
30–300 Specify the number of seconds between Embedded Web Server refreshes.
Contact Name Specify a contact name.
Location Specify the location.
Set an alarm when the printer requires user intervention.
Alarm Control Cartridge Alarm
For each alarm type, select from the following options:
Set the amount of time in minutes before the printer enters a lower power state.
Set the amount of time in minutes the printer waits after a job is printed before it goes into a reduced power state.
Print a job with the display turned off.
Print with Display Off
Allow printing with display off Display on when printing

Understanding the printer menus 99
Set the amount of time the printer waits before it enters Hibernate mode.
Disabled 20 minutes 1–3 hours 6 hours 1–3 days 1–2 weeks 1 month
Hibernate Timeout on Connection
Set the printer to Hibernate mode even if there is an active Ethernet connection.
Hibernate Do Not Hibernate
Set the amount of time in seconds before returning the control panel to a Ready state.
Set the printer to continue a specified job without returning to the home screen when the screen timeout timer expires.
Set the amount of time in seconds the printer waits to receive an end‑of‑job message before canceling the rest of the print job.
Set the amount of time in seconds the printer waits for additional data before canceling a print job.
Set the amount of time the printer waits for user intervention before it holds jobs that require unavailable resources and continues to print other jobs in the print queue.

Understanding the printer menus 100
Set the printer to restart when an error occurs.
Reboot when idle Reboot always Reboot never
Determine the number of automatic reboots the printer can perform.
Let the printer automatically continue printing from certain offline situations when these are not resolved within the specified time period.
Specify whether the printer reprints jammed pages.
Successfully print a page that may not have printed otherwise.
Determine how the printer, while in idle state, reacts to a short press of the Sleep button.
Do Nothing Sleep Hibernate
Press and Hold Sleep Button
Determine how the printer, while in idle state, reacts to a long press of the Sleep button.
Do Nothing Sleep Hibernate

Understanding the printer menus 101
Use the printer factory default settings.
Do Not Restore Restore Now
Export configuration files to a flash drive.
1–999 Specify a default number of copies for each print job.
Set a default paper source for all print jobs.
Tray [x] Multipurpose Feeder Manual Paper Manual Envelope
Generate color or black‑and‑white outputs.
Stack the pages of a print job in sequence when printing multiple copies.
(1,1,1) (2,2,2) (1,2,3) (1,2,3)
Specify whether prints are on one side or on both sides of the paper.
1 sided 2 sided
Define binding for duplexed pages in relation to paper orientation.
Long Edge Short Edge

Understanding the printer menus 102
Specify the orientation of a multiple‑page document.
Print multiple‑page images on one side of the paper.
Off 2‑Up 3‑Up 4‑Up 6‑Up 9‑Up 12‑Up 16‑Up
Print a border on each page image when using Paper Saver Border.
Specify the positioning of multiple‑page images when using Paper Saver Ordering.
Horizontal Reverse Horizontal Reverse Vertical Vertical
Specify whether blank separator sheets are inserted.
Off Between Copies Between Jobs Between Pages
Specify the paper source for separator sheets.
Tray [x] Multipurpose Feeder

Understanding the printer menus 103
Specify whether blank pages are inserted in a print job.
Do Not Print Print
Specify whether two‑sided (duplex) printing is set as the default for all print jobs.
1 sided 2 sided
Click File > Print, and then click Properties, Preferences, Options, or Setup. For Macintosh users:
Choose File > Print, and then adjust the settings from the Print dialog and pop‑up menus.
Define binding for duplexed pages in relation to page orientation.
Long Edge Short Edge
1–999 Specify the default number of copies for each print job.
Specify whether blank pages are inserted in a print job.
Do Not Print Print
Stack the pages of a print job in sequence when printing multiple copies.
(1,1,1) (2,2,2) (1,2,3) (1,2,3)

Understanding the printer menus 104
Specify whether blank separator sheets are inserted.
Off Between Copies Between Jobs Between Pages
Specify the paper source for the separator sheet.
Tray [x] Multipurpose Feeder
Print multiple pages on a single sheet of paper.
Off 2‑Up 3‑Up 4‑Up 6‑Up 9‑Up 12‑Up 16‑Up
Specify the order in which pages are printed on a single sheet when using Paper Saver.
Horizontal Reverse Horizontal Reverse Vertical Vertical
Specify the orientation in which pages are printed on a single sheet.
Print a border when using Paper Saver.
Specify whether to print images in color.

Understanding the printer menus 105
Adjust the color output on the printed page.
Specify the output resolution in dots per inch (dpi) or in color quality (CQ).
1200 dpi 4800 CQ
1–5 Lighten or darken the output.
Enable a print mode preferable for files such as architectural drawings, maps, electrical circuit diagrams, and flow charts.
Reduce the amount of toner used for graphics and images.
Adjust the brightness of the output.
‑6 to 6
0–5 Adjust the contrast of the output.
0–5 Adjust saturation in color outputs.
Enable an equal balance of colors in the output.
‑5 to 5 Magenta
‑5 to 5 Yellow
‑5 to 5 Black
‑5 to 5 Reset Defaults

Understanding the printer menus 106
Print sample pages for each of the RGB and CMYK color conversion tables used in the printer.
sRGB Display sRGB Vivid Display—True Black Vivid Off—RGB US CMYK Euro CMYK Vivid CMYK Off—CMYK
Customize the RGB color conversions.
RGB Image RGB Text RGB Graphics
Select from the following options:
Vivid sRGB Display Display—True Black sRGB Vivid Off
Customize the CMYK color conversions.
CMYK Image CMYK Text CMYK Graphics
Select from the following options:
US CMYK Euro CMYK Vivid CMYK Off
Color Adjust Initiate a recalibration of color conversion tables and allow the printer to make adjustments for color variations in output.
Spot Color Replacement Assign specific CMYK values to named spot colors.
RGB Replacement Match the colors of the output with that of the original document.

Understanding the printer menus 107
Set if the printer creates a log of the print jobs it receives.
Job Accounting Utilities Print and delete log files or export them to a flash drive.
Set how often a log file is created.
Log Action at End of Frequency
Set how the printer responds when the frequency threshold expires.
None E‑mail Current Log E‑mail & Delete Current Log Post Current Log Post & Delete Current Log
Log Near Full Level
Specify the maximum size of the log file before the printer executes the Log Action at Near Full.
Log Action at Near Full
Set how the printer responds when the hard disk is nearly full.
None E‑mail Current Log E‑mail & Delete Current Log E‑mail & Delete Oldest Log Post Current Log Post & Delete Current Log Post & Delete Oldest Log Delete Current Log Delete Oldest Log Delete All Logs Delete All But Current
Log Action at Full
Set how the printer responds when disk usage reaches the maximum limit (100MB).
None E‑mail & Delete Current Log E‑mail & Delete Oldest Log Post & Delete Current Log Post & Delete Oldest Log Delete Current Log Delete Oldest Log Delete All Logs Delete All But Current
URL to Post Logs Set where the printer posts job accounting logs.
E‑mail to Send Logs Specify the e‑mail address to which the device sends job accounting logs.

Understanding the printer menus 108
Log File Prefix Specify the prefix you want for the log file name.
Delete confidential and held jobs from the printer hard disk.
Confidential Held Not Restored All
Format the flash memory.
Delete Downloads on Disk
Delete downloads from the printer hard disk, including all held jobs, buffered jobs, and parked jobs.
Delete Now Do Not Delete
Activate Hex Trace Assist in isolating the source of a print job problem.

Understanding the printer menus 109
Provide an estimate of the percentage coverage of toner on a page. The estimate is printed on a separate page at the end of each print job.
Print a page containing information on errors, including XML markup errors.
Scale page content to fit the selected paper size.
Print annotations in a PDF.
Do Not Print Print
Print a page containing the PostScript error.
Lock PS Startup Mode
Enable users to disable the SysStart file.
Establish the font search order.

Understanding the printer menus 110
Enhance the contrast and sharpness of low‑resolution images and smoothen their color transitions.
Specify the set of fonts used in the Font Name menu.
Identify a specific font and where it is stored.
Specify the symbol set for each font name.
Change the point size for scalable typographic fonts.
1.00–1008.00
Specify the font pitch for scalable monospaced fonts.
0.08–100.00

Understanding the printer menus 111
Specify the orientation of text and graphics on a page.
Specify the number of lines that print on each page.
Set the printer to print on A4‑size paper.
198 mm 203 mm
Specify whether the printer automatically performs a carriage return (CR) after a line feed (LF) control command.
Auto CR after LF
Specify whether the printer automatically performs a line feed (LF) after a carriage return (CR) control command.
Auto LF after CR
Configure the printer to work with printer software or programs that use different source assignments for trays and feeders.
Off None 0–199 Assign Tray [x]
Off None 0–199 Assign Manual Paper
Off None 0–199 Assign Manual Envelope

Understanding the printer menus 112
Show the factory default setting assigned to each tray or feeder.
MPF Default = 8 T1 Default = 1 T2 Default = 4 T3 Default = 5 T4 Default = 20 T5 Default = 21 Env Default = 6 MPaper Default = 2 MEnv Default = 3
Restore all tray and feeder assignments to the factory default settings.
Joanna MT Letter Gothic Lubalin Graph Marigold MonaLisa Recut Monaco New CenturySbk New York Optima Oxford Palatino StempelGaramond Taffy Times TimesNewRoman Univers Zapf Chancery NewSansMTCS NewSansMTCT New SansMTJA NewSansMTKO
Set the default font for HTML documents.
Albertus MT Antique Olive Apple Chancery Arial MT Avant Garde Bodoni Bookman Chicago Clarendon Cooper Black Copperplate Coronet Courier Eurostile Garamond Geneva Gill Sans Goudy Helvetica Hoefler Text Intl CG Times Intl Courier Intl Univers

Understanding the printer menus 113
1–255 pt Set the default font size for HTML documents.
1–400% Scale the default font for HTML documents.
Set the page orientation for HTML documents.
8–255 mm Set the page margin for HTML documents.
Specify whether to print backgrounds on HTML documents.
Do Not Print Print
Select the optimal paper size, scaling, and orientation.
Invert bitonal monochrome images.
Scale the image to fit the selected paper size.
Anchor Top Left Best Fit Anchor Center Fit Height/Width Fit Height Fit Width

Understanding the printer menus 114
Set the image orientation.
Portrait Landscape Reverse Portrait Reverse Landscape
The Help menu consists of a series of Help pages that are stored in the printer as PDFs. They contain information about using the printer and performing printing tasks.
English, French, German, and Spanish translations are stored in the printer. Other translations are available at http://support.lexmark.com.
Print All Guides Prints all the guides
Media Guide Provides a list of the paper sizes supported in trays and feeders
Menu Map Provides a list of the printer control panel menus and settings
Printing Guide Provides information about loading paper and other specialty media
Color Quality Guide Provides information about solving color quality issues
Print Quality Provides information about solving print quality issues
Supplies Guide Provides part numbers for ordering supplies
Moving Guide Provides instructions for safely moving the printer
Connection Guide Provides information about connecting the printer locally (USB) or to a network
Print Defects Guide Provides information about resolving print defects
Use To · Orientation · Menu item Description

Saving money and the environment 115
Lexmark is committed to environmental sustainability and is continually improving its printers to reduce their impact on the environment. We design with the environment in mind, engineer our packaging to reduce materials, and provide collection and recycling programs. For more information, see:
By selecting certain printer settings or tasks, you may be able to reduce your printer's impact even further. This chapter outlines the settings and tasks that may yield a greater environmental benefit.
Studies show that as much as 80% of the carbon footprint of a printer is related to paper usage. You can significantly reduce your carbon footprint by using recycled paper and the following printing suggestions, such as printing on both sides of the paper and printing multiple pages on one side of a single sheet of paper.
For information on how you can quickly save paper and energy using one printer setting, see “Using Eco‑Mode” on page 116.
As an environmentally conscious company, Lexmark supports the use of recycled office paper produced specifically for use in laser printers. For more information on recycled papers that work well with your printer, see “Using recycled paper and other office papers” on page 57.
If your printer model supports two‑sided printing, then you can control whether print appears on one or two sides of the paper.
You can print up to 16 consecutive pages of a multiple‑page document onto one side of a single sheet of paper by setting multiple page printing (N‑Up) for the print job.

Saving money and the environment 116
Before printing or making multiple copies of a document:
Correctly set the paper type and size to avoid paper jams. For more information, see “Avoiding jams” on page 151.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Eco‑Mode > select a setting
Off Use the factory default settings for all settings associated with Eco‑Mode. Off supports the performance specifications of the printer.
Energy Reduce energy use, especially when the printer is idle.
Energy/Paper Use all the settings associated with Energy and Paper modes.
3 Click Submit.
Enable Quiet Mode to reduce printer noise.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Quiet Mode > select a setting
Use To

Saving money and the environment 117
On Reduce printer noise.
Off Use factory default settings.
3 Click Submit.
1 From the home screen, navigate to:
> Settings > General Settings > Timeouts > Sleep Mode
2 In the Sleep Mode field, select the number of minutes the printer is idle before it enters Sleep mode.
3 Apply the changes.
Hibernate is an ultra‑low‑power saving mode.
1 From the home screen, navigate to:
> Settings > General Settings
2 Touch Press Sleep Button or Press and Hold Sleep Button.
3 Touch Hibernate >
Hibernate Timeout lets you set the amount of time the printer waits after a print job is processed before it goes into a reduced power state.
1 Open a Web browser, and then type the printer IP address in the address field.
Use To

Saving money and the environment 118
2 Click Settings > General Settings > Timeouts.
3 From the Hibernate Timeout menu, select the number of hours, days, weeks, or months you want for the printer to wait before it goes into a reduced power state.
4 Click Submit.
1 From the printer control panel, navigate to:
> Settings > General Settings > Timeouts > Hibernate Timeout
2 Select the amount of time the printer waits after a print job is processed before it enters Hibernate mode.
Schedule Power Modes lets you schedule when the printer goes into a reduced power state or into the Ready state.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Schedule Power Modes.
3 From the Action menu, select the power mode.
4 From the Time menu, select the time.
5 From the Day(s) menu, select the day or days.
6 Click Add.
To save energy, or if you have trouble reading from the display, adjust the brightness of the display.
1 Open a Web browser, and then type the printer IP address in the address field.
3 Touch

Saving money and the environment 119
2 Select Settings > General Settings.
3 In the Screen Brightness field, enter the brightness percentage you want for the display.
4 Apply the changes.
1 From the home screen, navigate to:
> Settings > General Settings
2 In the Screen Brightness field, enter the brightness percentage you want for the display.
3 Apply the changes.
Lexmark provides collection programs and environmentally progressive approaches to recycling. For more information, see:
To return Lexmark products for recycling:
1 Go to www.lexmark.com/recycle.
2 Find the product type you want to recycle, and then select your country or region from the list.
3 Follow the instructions on the computer screen.
Lexmark continually strives to minimize packaging. Less packaging helps to ensure that Lexmark printers are transported in the most efficient and environmentally sensitive manner and that there is less packaging to dispose of. These efficiencies result in fewer greenhouse emissions, energy savings, and natural resource savings.
Lexmark cartons are 100% recyclable where corrugated recycling facilities exist. Facilities may not exist in your area.
The foam used in Lexmark packaging is recyclable where foam recycling facilities exist. Facilities may not exist in your area.

Saving money and the environment 120
When you return a cartridge to Lexmark, you can reuse the box that the cartridge came in. Lexmark will recycle the box.
Lexmark Cartridge Collection Program diverts millions of Lexmark cartridges from landfills annually by making it both easy and free for Lexmark customers to return used cartridges to Lexmark for reuse or recycling. One hundred percent of the empty cartridges returned to Lexmark are either reused or demanufactured for recycling. Boxes used to return the cartridges are also recycled.
To return Lexmark cartridges for reuse or recycling, follow the instructions that came with your printer or cartridge and use the prepaid shipping label. You can also do the following:
1 Go to www.lexmark.com/recycle.
2 From the Toner Cartridges section, select your country or region.
3 Follow the instructions on the computer screen.

Securing the printer 121
Using the security lock feature
The printer is equipped with a security lock feature. Attach a security lock compatible with most laptop computers in the location shown to secure the printer in place.


Your printer contains various types of memory that can store device and network settings, and user data.
Type of memory Description
Volatile memory Your printer uses standard random access memory (RAM) to temporarily buffer user data during simple print jobs.
Non-volatile memory Your printer may use two forms of non-volatile memory: EEPROM and NAND (flash memory). Both types are used to store the operating system, device settings, network information and bookmark settings, and embedded solutions.
Hard disk memory Some printers have a hard disk drive installed. The printer hard disk is designed for printer-specific functionality. This lets the printer retain buffered user data from complex print jobs, as well as form data, and font data.
Erase the content of any installed printer memory in the following circumstances:

Securing the printer 122
In high‑security environments, it may be necessary to take additional steps to make sure that confidential data stored in the printer hard disk cannot be accessed when the printer—or its hard disk—is removed from your premises.
The volatile memory (RAM) installed in your printer requires a power source to retain information. To erase the buffered data, simply turn off the printer.
Erase individual settings, device and network settings, security settings, and embedded solutions by following these steps:
1 Turn off the printer.
2 Hold down 2 and 6 on the keypad while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully turned on, a list of functions appears on the printer display instead of the standard home screen icons.
3 Touch Wipe All Settings.
The printer will restart several times during this process.
4 Touch Back > Exit Config Menu.
The printer will perform a power‑on reset, and then return to normal operating mode.

Securing the printer 123
1 Turn off the printer.
2 Hold down 2 and 6 while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully turned on, a list of functions appears on the printer display.
4 Press the up or down arrow button until Yes appears, and then proceed with disk wiping.
5 Navigate to:
Back > Exit Config Menu
The printer will perform a power‑on reset, and then return to normal operating mode.
In high-security environments, it may be necessary to take additional steps to make sure that confidential data stored in the printer cannot be accessed by unauthorized persons. For more information, visit the Lexmark security Web page.
You can also see the Embedded Web Server — Security: Administrator’s Guide for additional information:
1 Go to www.lexmark.com, and then navigate to Support & Downloads > select your printer.
2 Click the Manuals tab, and then select Embedded Web Server — Security: Administrator’s Guide.

Securing the printer 124
Enable hard disk encryption to prevent loss of sensitive data in the event the printer or its hard disk is stolen.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Security > Disk Encryption.
3 From the Disk encryption menu, select Enable.
4 Click Submit.
1 Turn off the printer.
2 Hold down 2 and 6 while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully turned on, a list of functions appears on the printer display.
3 Touch Disk Encryption > Enable.
4 Touch Yes to proceed with disk wiping.
5 Touch Back > Exit Config Menu.
The printer will perform a power‑on reset, and then return to normal operating mode.

Maintaining the printer 125
1 Make sure that the printer is turned off and unplugged from the electrical outlet.
2 Remove paper from the standard bin, multipurpose feeder, and manual feeder.
3 Remove any dust, lint, and pieces of paper around the printer using a soft brush or vacuum.
4 Dampen a clean, lint-free cloth with water, and use it to wipe the outside of the printer.
5 Make sure all areas of the printer are dry before sending a new print job.
A message appears on the display when a replacement supply item is needed or when maintenance is required. For more information, see “Supplies menu” on page 69.
From the home screen, navigate to:
Status/Supplies > View Supplies
1 Open a Web browser, and then type the printer IP address in the address field.

Maintaining the printer 126
2 Click Device Status > More Details.
The estimated number of remaining pages is based on the recent printing history of the printer. Its accuracy may vary significantly and is dependent on many factors, such as actual document content, print quality settings, and other printer settings.
The accuracy of the estimated number of remaining pages may decrease when the actual printing consumption is different from the historical printing consumption. Consider the variable level of accuracy before purchasing or replacing supplies based on the estimate. Until an adequate print history is obtained on the printer, initial estimates assume future supplies consumption based on the International Organization for Standardization* test methods and page content.
* Average continuous black or composite CMY declared cartridge yield in accordance with ISO/IEC 19798.
To order supplies in the U.S., contact Lexmark at 1-800-539-6275 for information about Lexmark authorized supplies dealers in your area. In other countries or regions, go to the Lexmark Web site at www.lexmark.com or contact the place where you purchased the printer.
Your Lexmark printer is designed to function best with genuine Lexmark supplies and parts. Use of third-party supplies or parts may affect the performance, reliability, or life of the printer and its imaging components. Use of third-party supplies or parts can affect warranty coverage. Damage caused by the use of third-party supplies or parts is not covered by the warranty. All life indicators are designed to function with Lexmark supplies and parts, and may deliver unpredictable results if third-party supplies or parts are used. Imaging component usage beyond the intended life may damage your Lexmark printer or its associated components.

Maintaining the printer 127

Item United States and Canada European Union (EU), European Economic Area
For more information on countries located in each region, visit www.lexmark.com/regions.


Maintaining the printer 128
Item All countries and regions
Black imaging kit 700Z1
Color imaging kit 700Z5
Item All countries and regions
Waste toner bottle C540X75G
Choose a cool, clean storage area for the printer supplies. Store supplies right side up in their original packing until you are ready to use them.
Do not expose supplies to:

Maintaining the printer 129

2 Waste toner bottle
3 Right side cover
1 Unpack the replacement waste toner bottle.
2 Open the front door.

1 Top door · 4 Front door

Maintaining the printer 130
3 Open the top door.

4 Remove the right side cover.

5 Remove the waste toner bottle.



Maintaining the printer 131
6 Pack the used waste toner bottle.
For more information, see “Recycling Lexmark products” on page 119.
7 Insert the replacement waste toner bottle.

8 Insert the right side cover.

9 Close the top door.
10 Close the front door.
1 Open the front door.

Maintaining the printer 132
2 Open the top door.
3 Remove the toner cartridges.



Maintaining the printer 133
4 Remove the right side cover.

5 Remove the waste toner bottle.

6 Lift the blue levers on the imaging kit, and then pull the imaging kit until it stops.


Maintaining the printer 134
7 Press down the blue lever, and then grasp the green handles on the sides to pull out the imaging kit.

8 Unpack the replacement black and color imaging kit.


9 Pack the used imaging kit.
For more information, see “Recycling Lexmark products” on page 119.



Maintaining the printer 135
10 Gently shake the yellow, cyan, magenta, and black developer units side‑to‑side.

11 Remove the red packing strip and the attached fabric from the developer units.

12 Insert the yellow, cyan, magenta, and black developer units into the matching color slots.

13 Remove the red packing strip from the imaging kit.


Maintaining the printer 136

14 Align, and then insert the imaging kit.

15 Push the blue levers down until the imaging kit is fully seated into place.

Maintaining the printer 137
16 Insert the waste toner bottle.
17 Insert the right side cover.


Maintaining the printer 138
18 Insert the toner cartridges.

19 Close the top door.
20 Close the front door.
1 Slide the release latch on the right side of the printer, and then open the top door.


Maintaining the printer 139
2 Remove the toner cartridge by lifting the handle, and then gently pulling it away from the imaging kit.


3 Unpack the new toner cartridge, and then remove its packaging.

Maintaining the printer 140
4 Align the new toner cartridge, and then press the cartridge down until it fits into place.

5 Close the top door.
6 Seal the used toner cartridge in the bag that the replacement toner cartridge came in before disposing.
For more information, see “Recycling Lexmark products” on page 119.
Replace the developer unit when a print quality defect occurs or when damage occurs to the printer.
1 Open the front door.

Maintaining the printer 141
2 Open the top door.
3 Remove the toner cartridges.

Maintaining the printer 142
4 Remove the right side cover.
5 Remove the waste toner bottle.
6 Lift the blue levers on the imaging kit, and then pull the imaging kit until it stops.

Maintaining the printer 143
7 Press down the blue lever, and then grasp the green handles on the sides to pull out the imaging kit.
8 Remove the used developer unit.

9 Gently shake the replacement developer unit side‑to‑side before removing it from its packaging.

Maintaining the printer 144
10 Remove the red shipping cover from the developer unit.
11 Insert the developer unit.
12 Align, and then insert the imaging kit.

Maintaining the printer 145
13 Push the blue levers down until the imaging kit is fully seated into place.
14 Insert the waste toner bottle.

Maintaining the printer 146
15 Insert the right side cover.
16 Insert the toner cartridges.
17 Close the top door.
18 Close the front door.
19 Pack the used developer unit in the bag that the replacement developer unit came in before disposing.
For more information, see “Recycling Lexmark products” on page 119.

Maintaining the printer 147
The printer and its hardware options can be safely moved to another location by following these precautions:
When shipping the printer, use the original packaging.

Managing the printer 148
Finding advanced networking and administrator information
This chapter covers basic administrative support tasks using the Embedded Web Server. For more advanced system support tasks, see the Networking Guide on the Software and Documentation CD or the Embedded Web Server — Security: Administrator's Guide on the Lexmark support Web site at http://support.lexmark.com.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Check the virtual display that appears at the top left corner of the screen.
The virtual display works as an actual display would work on a printer control panel.
You can view paper tray settings, the level of toner in the toner cartridges, the percentage of life remaining in the maintenance kit, and capacity measurements of certain printer parts from the Device Status page of the Embedded Web Server.
1 Type the printer IP address in the address field of your Web browser.
2 Click Device Status.
You can view some reports from the Embedded Web Server. These reports are useful for assessing the status of the printer, network, and supplies.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Reports, and then click the type of report you want to view.

Managing the printer 149
You can determine how you would like to be notified when supplies run nearly low, low, very low, or reach their end‑of‑life by setting the selectable alerts.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Print Settings > Supply Notifications.
3 From the drop‑down menu for each supply, select one of the following notification options:
Off The normal printer behavior for all supplies occurs.
E‑mail Only The printer generates an e-mail when the supply condition is reached. The status of the supply appears on the menus page and status page.
Continuable Stop1 The printer stops processing jobs when the supply condition is reached. The user needs to press a button to continue printing.
Non Continuable Stop1,2 The printer stops when the supply condition is reached. The supply must be replaced to continue printing.
1 The printer generates an e-mail about the status of the supply when supply notification is enabled.
2 The printer stops when some supplies become empty to prevent damage.
4 Click Submit.
1 Open a Web browser, and then type the printer IP address in the address field.
Notification Description

Managing the printer 150
2 Click Settings tab > Security > Confidential Print Setup.
4 Save the modified settings.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click the Copy Printer Settings.
3 To change the language, select a language from the drop-down menu, and then click Click here to submit language.
4 Click Printer Settings.
5 Type the IP addresses of the source and target printers in their appropriate fields.
6 Click Copy Printer Settings.
If you want to keep a list of the current menu settings for reference, then print a menu settings page before restoring the factory default settings. For more information, see “Printing a menu settings page” on page 39.
If you want a more comprehensive method of restoring the printer factory default settings, then perform the Wipe All Settings option. For more information, see “Erasing non‑volatile memory” on page 122.
From the home screen, navigate to:
> Settings > General Settings > Factory Defaults > Restore Now >

Avoiding jams
Correct loading of paper Incorrect loading of paper

Clearing jams 151



When a jam occurs, a message indicating the jam location and information to clear the jam appears on the printer display. Open the doors, covers, and trays indicated on the display to remove the jam.
Clearing jams 152
![Page 153 of the Lexmark CS510 user manual — [x]-page jam, clear standard bin.](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/page-153.webp?w=400)
![Lexmark CS510 — [x]-page jam, clear standard bin. diagram (page 153)](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/rimg-79.webp)
Jam location Message on the display What to do
1 Standard bin [x]‑page jam, clear standard bin. [203.xx]
Remove the jammed paper.
2 Fuser [x]‑page jam, open front door to clear fuser. [202.xx]
Open the front door, pull the tab and hold the fuser cover down, and then remove the jammed paper.
3 Front door [x]‑page jam, open front door. [20y.xx] Open the front door, and then remove the jammed paper.
4 Duplex [x]‑page jam, open front door to clear duplex. [23y.xx]
Open the front door, and then remove the jammed paper.
5 Tray [x] [x]‑page jam, open tray [x]. [24y.xx] Pull the indicated tray out, and then remove the jammed paper.
6 Manual feeder [x]‑page jam, clear manual feeder. [251.xx]
Remove the jammed paper.
7 Multipurpose feeder [x]‑page jam, clear multipurpose
Push the paper release lever to lift the paper rollers, and then remove the jammed paper.
feeder. [250.xx]
[x]‑page jam, clear standard bin.
1 Firmly grasp the jammed paper on each side, and then gently pull it out.
![Lexmark CS510 — [x]-page jam, clear standard bin. diagram (page 153)](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/rimg-80.webp)
Clearing jams 153
![Page 154 of the Lexmark CS510 user manual — [x]-page jam, open front door to clear fuser.](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/page-154.webp?w=400)
to clear the message and continue printing. For non‑touch‑screen printer
2 From the printer control panel, touch
models, select Next > Clear the jam, press OK, and then press to confirm.
[x]-page jam, open front door to clear fuser.
1 Open the front door.
![Lexmark CS510 — [x]-page jam, open front door to clear fuser. diagram (page 154)](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/rimg-81.webp)
2 Pull the green lever to open the fuser cover.
![Lexmark CS510 — [x]-page jam, open front door to clear fuser. diagram (page 154)](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/rimg-82.webp)
![Lexmark CS510 — [x]-page jam, open front door to clear fuser. diagram (page 154)](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/rimg-83.webp)
3 Hold down the fuser cover, and then remove the jammed paper.
Clearing jams 154
![Page 155 of the Lexmark CS510 user manual — [x]-page jam, open front door.](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/page-155.webp?w=400)
4 Close the front door.
5 From the printer control panel, touch
to clear the message and continue printing. For non‑touch‑screen printer
models, select Next > Clear the jam, press OK, and then press to confirm.
[x]-page jam, open front door.
1 Open the front door.
Clearing jams 155
![Page 156 of the Lexmark CS510 user manual — [x]-page jam, open front door to clear duplex.](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/page-156.webp?w=400)
![Lexmark CS510 — [x]-page jam, open front door to clear duplex. diagram (page 156)](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/rimg-84.webp)
2 Firmly grasp the jammed paper on each side, and then gently pull it out.
3 Close the front door.
to clear the message and continue printing. For non‑touch‑screen printer
4 From the printer control panel, touch
models, select Next > Clear the jam, press OK, and then press to confirm.
[x]‑page jam, open front door to clear duplex.
1 Open the front door.
Clearing jams 156
![Page 157 of the Lexmark CS510 user manual — [x]-page jam, open front door to clear duplex.](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/page-157.webp?w=400)
2 Firmly grasp the jammed paper on each side, and then gently pull it out.
3 Close the front door.
4 From the printer control panel, touch
to clear the message and continue printing. For non‑touch‑screen printer
models, select Next > Clear the jam, press OK, and then press to confirm.
Clearing jams 157
![Page 158 of the Lexmark CS510 user manual — [x]-page jam, open tray [x].](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/page-158.webp?w=400)
[x]‑page jam, open tray [x].
1 Pull the tray completely out of the printer.
![Lexmark CS510 — [x]-page jam, open tray [x]. diagram (page 158)](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/rimg-85.webp)
2 Firmly grasp the jammed paper on each side, and then gently pull it out.
![Lexmark CS510 — [x]-page jam, open tray [x]. diagram (page 158)](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/rimg-86.webp)
3 Insert the tray.
4 From the printer control panel, touch
to clear the message and continue printing. For non‑touch‑screen printer
models, select Next > Clear the jam, press OK, and then press to confirm.
Clearing jams 158
![Page 159 of the Lexmark CS510 user manual — [x] ‑ page jam, clear multipurpose feeder](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/page-159.webp?w=400)
[x]‑page jam, clear manual feeder.
1 Pull out the standard 250-sheet tray (Tray 1) and manual feeder.
![Lexmark CS510 — [x]-page jam, clear manual feeder. diagram (page 159)](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/rimg-87.webp)
2 Grasp the jammed paper on each side, and then gently pull it out.
![Lexmark CS510 — [x]-page jam, clear manual feeder. diagram (page 159)](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/rimg-88.webp)
3 Insert the tray.
4 From the printer control panel, touch
to clear the message and continue printing. For non‑touch‑screen printer
models, select Next > Clear the jam, press OK, and then press to confirm.
1 Push the paper release lever in the multipurpose feeder to access the jammed paper, and then gently pull it out.
Clearing jams 159
![Page 160 of the Lexmark CS510 user manual — [x]-page jam, clear manual feeder.](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/page-160.webp?w=400)
![Lexmark CS510 — [x]-page jam, clear manual feeder. diagram (page 160)](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/rimg-89.webp)
![Lexmark CS510 — [x]-page jam, clear manual feeder. diagram (page 160)](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/rimg-90.webp)
2 Flex the sheets of paper back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.
![Lexmark CS510 — [x]-page jam, clear manual feeder. diagram (page 160)](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/fig-160-1.webp)
3 Reload paper into the multipurpose feeder.
![Lexmark CS510 — [x]-page jam, clear manual feeder. diagram (page 160)](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/rimg-91.webp)
Clearing jams 160
![Page 161 of the Lexmark CS510 user manual — [x]-page jam, clear manual feeder.](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/page-161.webp?w=400)
4 Slide the paper guide until it rests lightly against the edge of the paper stack.
![Lexmark CS510 — [x]-page jam, clear manual feeder. diagram (page 161)](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/rimg-92.webp)
to clear the message and continue printing. For non‑touch‑screen printer
5 From the printer control panel, touch
models, select Next > > Clear the jam, press OK > .
Clearing jams 161

Understanding the printer messages
Wait for the process to complete.
Try one or more of the following:
panel to clear the message and continue printing. For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
panel to clear the message and continue printing. For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
panel to clear the message and continue printing. For non‑touch‑screen printer models, press to confirm.
Make sure the right side cover is installed, and then close the front and top doors to clear the message.
Troubleshooting 162
![Page 163 of the Lexmark CS510 user manual — Complex page, some data may not have printed [39]](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/page-163.webp?w=400)
You may need to order a toner cartridge. If necessary, select Continue to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
You may need to replace the toner cartridge very soon. For more information, see the “Replacing supplies” section of the User’s Guide.
If necessary, select Continue on the printer control panel to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
You may need to order an imaging kit. If necessary, select Continue on the printer control panel to clear the message
and continue printing. For non‑touch‑screen printer models, press to confirm.
If necessary, select Continue on the printer control panel to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
You may need to replace the imaging kit very soon. For more information, see the “Replacing supplies” section of the User’s Guide.
If necessary, select Continue on the printer control panel to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
printer models, press to confirm.
Troubleshooting 163
![Page 164 of the Lexmark CS510 user manual — Incorrect paper size, open [paper source] [34]](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/page-164.webp?w=400)
Held jobs are invalidated because of any of the following possible changes in the printer:
From the printer control panel, select Continue to clear the message. For non-touch-screen printer models, press to confirm.
Try one or more of the following:
printer models, press to confirm. • Cancel the current print job.
Error reading USB drive. Remove USB.
An unsupported USB device is inserted. Remove the USB device, and then insert a supported one.
Error reading USB hub. Remove hub.
An unsupported USB hub has been inserted. Remove the USB hub, and then install a supported one.
Remove, and then reinstall the indicated tray to clear the message.
Try one or more of the following:
Troubleshooting 164
![Page 165 of the Lexmark CS510 user manual — Insufficient memory, some held jobs will not be restored [37]](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/page-165.webp?w=400)
Insert the indicated tray into the printer.
Try one or more of the following:
The printer deleted some held jobs in order to process current jobs.
Select Continue to clear the message. For non-touch-screen printer models, press to confirm.
Try one or more of the following:
rest of the print job. For non‑touch‑screen printer models, press to confirm. • Cancel the current print job.
Install additional printer memory or select Continue on the printer control panel to disable Resource Save, clear the
message, and continue printing. For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
to confirm. • Delete other held jobs to free up additional printer memory.
Troubleshooting 165
![Page 166 of the Lexmark CS510 user manual — Load [paper source] with [paper type] [paper size]](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/page-166.webp?w=400)
Try one or more of the following:
non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
panel. For non‑touch‑screen printer models, press to confirm.
Troubleshooting 166
![Page 167 of the Lexmark CS510 user manual — Maintenance kit nearly low [80.xy]](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/page-167.webp?w=400)
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
You may need to order a maintenance kit. For more information, visit the Lexmark support Web site at http://support.lexmark.com or contact customer support, and then report the message.
If necessary, select Continue to clear the message and continue printing. For non‑touch‑screen printer models,
press to confirm.
For more information, visit the Lexmark support Web site at http://support.lexmark.com or contact customer support, and then report the message.
Troubleshooting 167
![Page 168 of the Lexmark CS510 user manual — Non-Lexmark [color] [supply type], see User's Guide [33.xy]](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/page-168.webp?w=400)
If necessary, select Continue to clear the message and continue printing. For non‑touch‑screen printer models,
press to confirm.
You may need to replace the maintenance kit very soon. For more information, visit the Lexmark support Web site at http://support.lexmark.com or contact customer support, and then report the message.
If necessary, select Continue on the printer control panel to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
to confirm. • Install additional printer memory.
Try one or more of the following:
Try one or more of the following:
The printer has detected a non‑Lexmark supply or part installed in the printer.
Your Lexmark printer is designed to function best with genuine Lexmark supplies and parts. Use of third-party supplies or parts may affect the performance, reliability, or life of the printer and its imaging components.
Troubleshooting 168
![Page 169 of the Lexmark CS510 user manual — Reinstall missing or unresponsive [type] imaging kit [31.xy]](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/page-169.webp?w=400)
All life indicators are designed to function with Lexmark supplies and parts, and may deliver unpredictable results if third-party supplies or parts are used. Imaging component usage beyond the intended life may damage your Lexmark printer or its associated components.
To accept any and all of these risks, and to proceed with the use of non-genuine supplies or parts in your printer, press
and hold and the # button on the printer control panel simultaneously for 15 seconds.
If you do not wish to accept these risks, then remove the third-party supply or part from your printer, and then install a genuine Lexmark supply or part.
Try one or more of the following:
printer models, press to confirm. • If the printer cannot find the requested font, then from the printer control panel, navigate to:
PPDS menu > Best Fit > On
The printer will find a similar font and reformat the affected text. • Cancel the current print job.
Try one or more of the following:
Try one or more of the following:
Troubleshooting 169
![Page 170 of the Lexmark CS510 user manual — Replace [type] imaging kit, 0 estimated pages remain [84.xy]](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/page-170.webp?w=400)
Try any of the following:
sheet. For non‑touch‑screen printer models, press to confirm. • Cancel the print job.
1 Remove any remaining packing material from the indicated location.
2 From the printer control panel, touch Continue to clear the message. For non‑touch‑screen printer models, press
to confirm.
Remove the paper stack from the standard bin.
Replace the indicated toner cartridge to clear the message and continue printing. For more information, see the instruction sheet that came with the supply.
Install a toner cartridge that matches the region number of the printer. x indicates the value of the printer region. y indicates the value of the cartridge region. x and y can have the following values:
1 United States, Canada
2 European Union (EU), European Economic Area (EEA), Switzerland
8 Rest of the world
![Page 171 of the Lexmark CS510 user manual — Replace unsupported [color] cartridge [32.xy]](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/page-171.webp?w=400)
Replace the indicated imaging kit to clear the message and continue printing. For more information, see the instruction sheet that came with the supply.
Replace the defective toner cartridge to clear the message. For more information, see the instruction sheet that came with the supply.
Replace the defective imaging kit to clear the message and continue printing. For more information, see the instruction sheet that came with the supply.
The printer is scheduled for maintenance. For more information, visit the Lexmark support Web site at http://support.lexmark.com or contact your service representative, and then report the message.
Install the indicated toner cartridge to clear the message. For more information, see the “Replacing supplies” section of the User’s Guide.
Install the indicated imaging kit to clear the message. For more information, see the “Replacing supplies” section of the User’s Guide.
Replace the waste toner bottle to clear the message.
Remove the toner cartridge, and then install a supported one to clear the message.
Troubleshooting 171
![Page 172 of the Lexmark CS510 user manual — Standard USB port disabled [56]](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/page-172.webp?w=400)
Remove the indicated imaging kit, and then install a supported one to clear the message.
Install the missing waste toner bottle to clear the message. For more information, see the instruction sheet that came with the supply.
Try one or more of the following:
SMTP server not set up. Contact system administrator.
From the printer control panel, touch Continue to clear the message.
From the printer control panel, select Continue to clear the message. For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
From the printer control panel, select Continue to clear the message. For non‑touch‑screen printer models, press to confirm.
Troubleshooting 172
![Page 173 of the Lexmark CS510 user manual — Unformatted flash detected [53]](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/page-173.webp?w=400)
Try one or more of the following:
are needed to continue processing the current job. For non‑touch‑screen printer models, press to clear the message and continue printing.
1 Order the missing supply immediately. 2 Install the supply. For more information, see the instruction sheet that came with the supply. • Cancel the print job, then install the missing supply, and then resend the print job.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet.
3 Remove the extra flash memory.
4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet.
3 Remove the extra trays.
4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
Try one or more of the following:
printer models, press to confirm. • Format the flash memory.
Troubleshooting 173

You may need to order a waste toner bottle. If necessary, select Continue on the printer control panel to clear the
message and continue printing. For non‑touch‑screen printer models, press to confirm.
Weblink server not set up. Contact system administrator.
An error occurred on the Weblink server, or the server is not configured properly. Touch Continue to clear the message. If the message appears again, contact your system support person.
Go to step 2. Turn on the printer.
Make sure the printer is turned on.
Is the printer turned on?
Press the Sleep button to wake the printer from Sleep mode or Hibernate mode.
Go to step 3.
Check if the printer is in Sleep mode or Hibernate mode.
Is the printer in Sleep mode or Hibernate mode?
Go to step 4. Plug one end of the power cord into the printer and the other to a properly grounded electrical outlet.
Check if one end of the power cord is plugged into the printer and the other to a properly grounded electrical outlet.
Is the power cord plugged into the printer and a properly grounded electrical outlet?
Unplug the other electrical equipment, and then turn on the printer. If the printer does not work, then reconnect the other electrical equipment.
Go to step 5.
Check other electrical equipment plugged into the electrical outlet.
Does other electrical equipment work?
![Page 175 of the Lexmark CS510 user manual — Waste toner bottle nearly full [82.xy]](/cdn/reader/76/7633092f350ad386545430ff73558fa6d6f7b0a614b410019ced6032814fb7e2/images/page-175.webp?w=400)
Go to step 6. Make sure to match the following:
Check if the cables connecting the printer and the computer are inserted in the correct ports.
Are the cables inserted in the correct ports?
Step 6 Make sure the electrical outlet is not turned off by a switch or breaker.
Turn on the switch or reset the breaker.
Go to step 7.
Is the electrical outlet turned off by a switch or breaker?
Connect the printer power cord directly to a properly grounded electrical outlet.
Go to step 8.
Check if the printer is plugged into any surge protectors, uninterruptible power supplies, or extension cords.
Is the printer plugged into any surge protectors, uninterruptible power supplies, or extension cords?
Step 8 Check if one end of the printer cable is plugged into a port on the printer and the other to the computer, print server, option, or other network device.
Go to step 9. Connect the printer cable securely to the printer and the computer, print server, option, or other network device.
Is the printer cable securely attached to the printer and the computer, print server, option, or other network device?
Go to step 10. Turn off the printer, remove all packing materials, then reinstall the hardware options, and then turn on the printer.
Make sure to install all hardware options properly and remove any packing material.
Are all hardware options properly installed and all packing material removed?
Go to step 11. Use correct printer driver settings.
Check if you have selected the correct port settings in the printer driver.
Are the port settings correct?
Go to step 12. Install the correct printer driver.
Check the installed printer driver.
Is the correct printer driver installed?
The problem is solved. Contact customer support.
Turn off the printer, then wait for about 10 seconds, and then turn the printer back on.
Is the printer working?

The problem is solved. Go to step 2.
Press the Sleep button on the printer control panel.
Does Ready appear on the printer display?
The problem is solved. Turn off the printer, and then contact customer support.
Turn off the printer, then wait for about 10 seconds, and then turn the printer back on.
Do Please wait and Ready appear on the printer display?
Make sure the memory card is installed.
The problem is solved. Contact customer support.
a Install the memory card. For more information, see “Installing a
memory card” on page 25.
Installed Options list.
Is the card listed in the Installed Options list?
The problem is solved. Go to step 2.
Turn off the printer, then wait for about 10 seconds, and then turn the printer back on.
Does the internal option operate correctly?
Go to step 3. Connect the internal option to the controller board.
Check if the internal option is properly installed in the controller board.
a Turn off the printer. b Unplug the power cord from the electrical outlet.
c Make sure the internal option is installed in the appropriate connector
in the controller board. d Turn the printer back on.
Is the internal option properly installed in the controller board?

Go to step 4. Reinstall the internal option.
Print a menu settings page, and then check to see if the internal option is listed in the Installed Options list.
Is the internal option listed in the menu settings page?
Go to step 5. Manually add the internal option in the printer driver.
Check if the option is available in the printer driver.
It may be necessary to manually add the internal option in the printer driver to make it available for print jobs. For more information, see “Adding available options in the print driver” on page 35.
Is the internal option available in the printer driver?
The problem is solved. Contact customer support.
a Check if the internal option is selected.
Does the internal option operate correctly?
The problem is solved. Go to step 2.
a Pull out the tray, and then do one or more of the following:
Is the tray working?
The problem is solved. Go to step 3.
a Turn off the printer, then wait about 10 seconds, and then turn the
printer back on. b Resend the print job.
Is the tray working?

Go to step 4. Reinstall the tray. For more information, see the setup documentation that came with the tray.
Check if the tray is installed and recognized by the printer.
Print a menu settings page, and then check if the tray is listed in the Installed Features list.
Is the tray listed in the menu settings page?
The problem is solved. Contact customer support.
Check if the tray is available in the printer driver.
Is the tray available in the printer driver?
a Turn on jam recovery.
The problem is solved. Contact customer support.
1 From the printer control panel, navigate to:
Settings > General Settings > Print Recovery > Jam Recovery 2 Select On or Auto.
3 Depending on your printer model, press or touch Submit. b Resend the pages that did not print.
Were the jammed pages reprinted?

Go to step 2. The problem is solved.
a Pull out the tray, and then do one or more of the following:
If jam recovery is enabled, then the print jobs will reprint automatically.
Do paper jams still occur frequently?
Go to step 3. The problem is solved.
a Load paper from a fresh package.
Do paper jams still occur frequently?
Contact customer support.
The problem is solved.
a Review the tips on avoiding jams. For more information, see “Avoiding
jams” on page 151. b Follow the recommendations, and then resend the print job.
Do paper jams still occur frequently?
a Do either of the following:
Contact customer support.
The problem is solved.
or Done.
the jam, press OK > . b Follow the instructions on the printer display.
Does the paper jam message remain?

Step 1 Check the system log for relevant details.
Go to step 2. Contact customer support.
a Open a Web browser, and then type the printer IP address in the
address field.
If you do not know the IP address of the printer, then you can:
c From the Filter menu, select an application status. d From the Application menu, select an application, and then click
Submit.
Does an error message appear in the log?
Step 2 Resolve the error.
The problem is solved. Contact customer support.
Is the application working now?
Troubleshooting 180 · Action Yes No

Step 1 Make sure the printer is not in Hex Trace mode.
Deactivate Hex Trace mode.
Go to step 2.
Is the printer in Hex Trace mode?
Contact customer support.
The problem is solved.
a From the printer control panel, select Standard Network or
Network [x], and then set SmartSwitch to On. b Resend the print job.
Do incorrect characters print?
The problem is solved. Go to step 2.
a Check if you are printing on paper that is supported by the tray. b Resend the print job.
Did the job print from the correct tray or on the correct paper?
The problem is solved. Go to step 3.
a From the Paper menu on the printer control panel, set the paper size
and type to match the paper loaded in the tray. b Resend the print job.
Did the job print from the correct tray or on the correct paper?
The problem is solved. Go to step 4.
a Depending on your operating system, open Printing Preferences or
the Print dialog, and then specify the paper type. b Resend the print job.
Did the job print from the correct tray or on the correct paper?

The problem is solved. Contact customer support.
a Check if the trays are not linked. b Resend the print job.
Did the job print from the correct tray or on the correct paper?
The problem is solved. Go to step 2.
a From the Finishing menu on the printer control panel, set Collate to
(1,2,3) (1,2,3). b Resend the print job.
Did the job print and collate correctly?
The problem is solved. Go to step 3.
a From the printer software, set Collate to (1,2,3) (1,2,3).
Did the job print and collate correctly?
The problem is solved. Contact customer support.
Reduce the complexity of the print job by eliminating the number and size of fonts, the number and complexity of images, and the number of pages in the job.
Did the job print and collate correctly?
Go to step 2. Insert the flash drive into the front USB port.
Check if the flash drive is inserted into the front USB port.
Is the flash drive inserted into the front USB port?
Wait until the printer is ready, then view the held jobs list, and then print the documents.
Go to step 3.
Check if the indicator light on the printer control panel is blinking green.
Is the indicator light blinking green?

Go to step 4. The problem is solved.
a Check for an error message on the display. b Clear the message.
Does the error message still appear?
Go to step 5. The problem is solved.
Check if the flash drive is supported.
For more information on tested and approved USB flash drives, see “Supported flash drives and file types” on page 65.
Does the error message still appear?
Contact customer support.
The problem is solved.
Check if the USB port is disabled by the system support person.
Does the error message still appear?
Place letter‑ or A4‑size paper in the tray, and then resend the print job.
The problem is solved. Contact customer
Does the print speed increase?
support.
The problem is solved. Go to step 2.
a From the document you are trying to print, open the Print dialog and
check if you have selected the correct printer.
Do the jobs print?
The problem is solved. Go to step 3.
a Check if the printer is plugged in and turned on, and if Ready appears
on the printer display. b Resend the print job.
Do the jobs print?

The problem is solved. Go to step 4.
If an error message appears on the printer display, then clear the message.
Do the jobs print?
The problem is solved. Go to step 5.
a Check if the ports (USB, serial, or Ethernet) are working and if the
cables are securely connected to the computer and the printer.
Do the jobs print?
The problem is solved. Go to step 6.
a Turn off the printer, then wait for about 10 seconds, and then turn the
printer back on. b Resend the print job.
Do the jobs print?
The problem is solved. Contact customer support.
a Remove, and then reinstall the printer software. For more
information, see “Installing the printer” on page 34.
Do the jobs print?
The problem is solved. Go to step 2.
Change the environmental settings of the printer.
a From the printer control panel, navigate to:
Settings > General Settings b Select Eco‑Mode or Quiet Mode, and then select Off.
Did the job print?

The problem is solved. Go to step 3.
Reduce the number and size of fonts, the number and complexity of images, and the number of pages in the print job, and then resend the job
Did the job print?
The problem is solved. Go to step 4.
a Remove held jobs stored in the printer memory. b Resend the print job.
Did the job print?
The problem is solved. Go to step 5.
a Disable the Page Protect feature.
From the printer control panel, navigate to:
Settings > General Settings > Print Recovery > Page Protect > Off b Resend the print job.
Did the job print?
The problem is solved. Contact customer support.
Install additional printer memory, and then resend the print job.
Did the job print?

a Check if the distance between the defects is equal to one of the
1 Check if the distance between the defects is equal to one of the following:
The problem is solved.
following:
(1.17 in.), or 94.2 mm (3.70 in.), then replace the photoconductor unit. c If the distance between the defects equals 43.9 mm (1.72 in.) or
45.5 mm (1.79 in.), then replace the developer unit.
Do the repeating defects still appear?
The problem is solved. Go to step 2.
a Open the trays, and then check if they contain paper of the same size
and type.
Do the trays link correctly?
The problem is solved. Contact customer support.
a From the printer control panel, set the paper size and type in the Paper
menu to match the paper loaded in the trays to be linked.
Do the trays link correctly?

Multiple‑language PDF files do not print
The problem is solved. Go to step 2.
a Check if the print options for the PDF output are set to embed all fonts. b Generate a new PDF file, and then resend the print job.
Do the files print?
The problem is solved. Contact customer support.
a Open the document you want to print in Adobe Acrobat. b Click File > Print > Advanced > Print As Image > OK > OK.
Do the files print?
The problem is solved. Go to step 2.
Adjust the print timeout settings.
a From the printer control panel, navigate to:
Settings > General Settings > Timeouts > Print Timeout b Select a higher setting and then, depending on your printer model,
select or Submit. c Resend the print job.
Did the file print correctly?
The problem is solved. Contact customer support.
a Check the original file for manual page breaks. b Resend the print job.
Did the file print correctly?


Go to step 2. Select a font that is supported by the printer.
a Print a font sample list to check if the fonts you are using are supported
Menus > Reports > Print Fonts 2 Select PCL Fonts or PostScript Fonts. b Resend the print job.
Are you using fonts that are supported by the printer?
Check if the fonts installed on the computer are supported by the printer.
Are the fonts installed on the computer supported by the printer?

a Move the width and length guides in the tray to the correct positions
for the paper loaded. b Resend the print job.
Go to step 3. Do one or more of the following:
From the printer control panel, set the paper size and type in the Paper menu to match the paper loaded in the tray.
Does the paper size match the paper loaded in the tray?
Troubleshooting 188


a Depending on your operating system, specify the paper size from
Printing Preferences or from the Print dialog. b Resend the print job.

a From the Quality menu on the printer control panel, reduce the toner
Troubleshooting 189



a Make sure your software program is using a correct fill pattern. b Resend the print job.
a Load the specified tray or feeder with a recommended type of paper. b Resend the print job.
Troubleshooting 190

Contact customer support.
The problem is solved.
Replace the imaging kit, and then resend the print job.
Do horizontal voids appear on prints?
ABCD ABCD ABCD
The problem is solved. Go to step 2.
a Move the width and length guides in the tray to the correct positions
for the paper size loaded. b Resend the print job.
Are the margins correct?
Step 2 From the printer control panel, set the paper size in the Paper menu to match the paper loaded in the tray.
Go to step 3. Do one or more of the following:
Does the paper size match the paper loaded in the tray?
The problem is solved. Contact customer support.
a Depending on your operating system, specify the paper size from
Printing Preferences or from the Print dialog. b Resend the print job.
Are the margins correct?

Go to step 2. Adjust the width and length guides.
Move the width and length guides in the tray to the correct positions for the size of the paper loaded.
Are the width and length guides positioned correctly?
Go to step 3. Specify the paper type and weight from the tray settings to match the paper loaded in the tray.
From the printer control panel, set the paper type and weight in the Paper menu to match the paper loaded in the tray.
Do the paper type and weight match the type and weight of the paper in the tray?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type and
weight from Printing Preferences or from the Print dialog. b Resend the print job.
Is the paper still curled?
Go to step 5. The problem is solved.
a Remove the paper from the tray, and then turn it over. b Resend the print job.
Is the paper still curled?
Contact customer support.
The problem is solved.
a Load paper from a fresh package.
Is the paper still curled?
) ) ABCDE
ABCDE ABCDE

Go to step 2. The problem is solved.
a Move the width and length guides in the tray to the correct positions
for the size of the paper loaded in the tray. b Resend the print job.
Do print irregularities still appear?
Go to step 3. Do one or more of the following:
From the printer control panel, set the paper size and type in the Paper menu to match the paper loaded in the tray.
Is the tray set to the size and type of the paper loaded in the tray?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type and
weight from Printing Preferences or from the Print dialog. b Resend the print job.
Do print irregularities still appear?
From the printer control panel, set the paper texture in the Paper menu to match the paper loaded in the tray.
Go to step 5.
Check if the paper loaded in the tray has texture or rough finishes.
Are you printing on textured or rough paper?
Go to step 6. The problem is solved.
a Load paper from a fresh package.
Do print irregularities still appear?
Step 6 Replace the imaging kit, and then resend the print job.
Contact customer support.
The problem is solved.
Do print irregularities still appear?

Go to step 2. The problem is solved.
a From the Quality menu on the printer control panel, select Color
Adjust. b Resend the print job.
Is the print still too dark?
Go to step 3. The problem is solved.
a From the Quality menu on the printer control panel, reduce the toner
darkness.
Is the print still too dark?
Go to step 4. Change the paper loaded in the tray to match the paper type, texture, and weight specified in the tray settings.
a From the printer control panel, set the paper type, texture, and weight
in the Paper menu to match the paper loaded in the tray. b Resend the print job.
Is the tray set to the type, texture, and weight of the paper loaded?
Go to step 5. The problem is solved.
a Depending on your operating system, specify the paper type, texture
and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Is the print still too dark?
Step 5 Check if the paper loaded in the tray has texture or rough finishes.
From the printer control panel, set the paper texture in the Paper menu to match the paper loaded on the tray.
Go to step 6.
Are you printing on textured or rough paper?

Go to step 7. The problem is solved.
a Load paper from a fresh package.
Is the print still too dark?
Contact customer support.
The problem is solved.
Replace the imaging kit, and then resend the print job.
Is the print still too dark?
Go to step 2. The problem is solved.
a From the Quality menu on the printer control panel, select Color
Adjust. b Resend the print job.
Is the print still too light?
Go to step 3. The problem is solved.
a From the Quality menu on the printer control panel, increase the toner
darkness.
Is the print still too light?
Go to step 4. Specify the paper type, texture, and weight from the tray settings to match the paper loaded in the tray.
From the printer control panel, set the paper type, texture, and weight in the Paper menu to match the paper loaded in the tray.
Is the tray set to the type, texture, and weight of the paper loaded?

Go to step 5. The problem is solved.
a Depending on your operating system, specify the paper type, texture,
and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Is the print still too light?
From the printer control panel, set the paper texture in the Paper menu to match the paper loaded in the tray
Go to step 5.
Make sure that the paper has no texture or rough finishes.
Are you printing on textured or rough paper?
Go to step 7. The problem is solved.
a Load paper from a fresh package.
Is the print still too light?
Contact customer support.
The problem is solved.
Replace the imaging kit, and then resend the print job.
Is the print still too light?

Go to step 2. The problem is solved.
a Check if there is packing material left on the imaging kit.
1 Remove the imaging kit. 2 Check if the packing material is properly removed from the imaging kit.
Is the printer still printing blank pages?
Contact customer support.
The problem is solved.
Replace the imaging kit, and then resend the print job.
Is the printer still printing blank pages?
Go to step 2. The problem is solved.
a Remove, and then reinstall the imaging kit.
Is the printer printing solid black pages?
Contact customer support.
The problem is solved.
Replace the imaging kit, and then resend the print job.
Is the printer printing solid black pages?


Go to step 2. Load paper with the correct paper type and weight in the tray.
Check if the paper loaded in the tray has the correct paper type and weight.
Is paper with the correct paper type and weight loaded in the tray?
Go to step 3. Change the paper type and weight to match the paper loaded in the tray.
From the printer control panel, set the paper type and weight in the Paper menu to match the paper loaded in the tray.
Do the printer settings match the type and weight of the paper loaded?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type and
weight from Printing Preferences or from the Print dialog. b Resend the print job.
Do shadow images still appear on prints?
Contact customer support.
The problem is solved.
Replace the imaging kit, and then resend the print job.
Do shadow images still appear on prints?
) ) ABCDE
ABCDE ABCDE

Go to step 2. The problem is solved.
a Move the width and length guides in the tray to the correct positions
for the size of the paper loaded. b Resend the print job.
Is the print still skewed?
Contact customer support.
The problem is solved.
a Check if you are printing on a paper that is supported by the tray. b Resend the print job.
Is the print still skewed?
ABCDE ABCDE ABCDE
Go to step 2. The problem is solved.
a Depending on your operating system, specify the tray or feeder from
Printing Preferences or the Print dialog. b Resend the print job.
Do streaked horizontal lines appear on prints?
Go to step 3. Do one or more of the following:
From the printer control panel, set the paper type and weight in the Paper menu to match the paper loaded in the tray.
Do the paper type and weight match the paper in the tray?


Replace the imaging kit, and then resend the print job.

a Depending on your operating system, specify the paper type, texture,
and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Troubleshooting 200

Go to step 3. Do one or more of the following:
From the printer control panel, set the paper texture, type, and weight in the Paper menu to match the paper loaded in the tray.
Do the paper texture, type, and weight match the paper in the tray?
Go to step 4. The problem is solved.
a Load paper from a fresh package.
Do streaked vertical lines appear on prints?
Go to step 5. The problem is solved.
a Remove, and then reinstall the imaging kit.
Do streaked vertical lines appear on prints?
Contact customer support.
The problem is solved.
Replace the imaging kit, and then resend the print job.
Do streaked vertical lines appear on prints?

Go to step 2. Set the paper type to Transparency.
From the printer control panel, set the paper type in the Paper menu to match the paper loaded in the tray.
Is the paper type for the tray set to Transparency?
Contact customer support.
The problem is solved.
a Check if you are using a recommended type of transparency. b Resend the print job.
Is the print quality still poor?
ABCDE
ABCDE ABCDE
The problem is solved. Go to step 2.
a Remove, and then reinstall the imaging kit.
Does fog or shading disappear from the prints?
The problem is solved. Contact customer support.
Replace the imaging kit, and then resend the print job.
Does fog or shading disappear from the prints?


Go to step 2. Specify the paper type, texture, and weight from the tray settings to match the paper loaded in the tray.
From the Paper menu on the printer control panel, check the paper type, texture, and weight.
Do the paper type, texture, and weight match the paper loaded in the tray?

Replace the imaging kit, and then resend the print job.

Replace the imaging kit, and then resend the print job.
Troubleshooting 203

Go to step 2. The problem is solved.
a Check if your software program is using a correct fill pattern. b Resend the print job.
Do vertical voids appear on prints?
Go to step 3. The problem is solved.
a From the Paper Menu on the printer control panel, check the paper
type and paper weight. b Resend the print job.
Do vertical voids appear on prints?
Step 3 Check if you are using a recommended type of paper.
Go to step 4. The problem is solved.
a Load paper source with a recommended type of paper. b Resend the print job.
Do vertical voids appear on prints?
Go to step 5. The problem is solved.
a Remove, and then reinstall the imaging kit.
Do vertical voids appear on prints?
Contact customer support.
The problem is solved.
Replace the imaging kit, and then resend the print job.
Do vertical voids appear on prints?

What is RGB color?
Red, green, and blue light can be added together in various amounts to produce a large range of colors observed in nature. For example, red and green can be combined to create yellow. Televisions and computer monitors create colors in this manner. RGB color is a method of describing colors by indicating the amount of red, green, or blue needed to produce a certain color.
What is CMYK color?
Cyan, magenta, yellow, and black inks or toners can be printed in various amounts to produce a large range of colors observed in nature. For example, cyan and yellow can be combined to create green. Printing presses, inkjet printers, and color laser printers create colors in this manner. CMYK color is a method of describing colors by indicating the amount of cyan, magenta, yellow, and black needed to reproduce a particular color.
How is color specified in a document to be printed?
Software programs typically specify the document color using RGB or CMYK color combinations. Additionally, they let users modify the color of each object in a document. For more information, see the help information of your operating system.
How does the printer know what color to print?
When a user prints a document, information describing the type and color of each object is sent to the printer. The color information is passed through color conversion tables that translate the color into the appropriate amounts of cyan, magenta, yellow, and black toner needed to produce the color you want. The object information determines the application of color conversion tables. For example, it is possible to apply one type of color conversion table to text while applying a different color conversion table to photographic images.
What is manual color correction?
When manual color correction is enabled, the printer employs user‑selected color conversion tables to process objects. However, Color Correction must be set to Manual, or no user‑defined color conversion will be implemented. Manual color correction settings are specific to the type of object being printed (text, graphics, or images), and how the color of the object is specified in the software program (RGB or CMYK combinations).
To manually apply a different color conversion table, do the following:
1 From the Quality menu on the printer control panel, select Color Correction, and then select Manual.
2 From the Quality menu on the printer control panel, select Manual Color, and then select the appropriate color conversion table for the affected object type.
Troubleshooting 205

Object type Color conversion tables
How can I match a particular color (such as a corporate logo)?
Nine types of Color Samples sets are available from the Quality menu on the printer control panel. These are also available from the Color Samples page of the Embedded Web Server. Selecting any sample set generates a multiple‑page printout consisting of hundreds of colored boxes. Either a CMYK or RGB combination is located on each box, depending on the table selected. The observed color of each box is obtained by passing the CMYK or RGB combination labeled on the box through the selected color conversion table.
By examining Color Samples sets, you can identify the box whose color is the closest to the color you want. The color combination labeled on the box can then be used for modifying the color of the object in a software program. For more information, see the help information of your operating system.
Selecting which Color Samples set to use for a particular color‑matching problem depends on the Color Correction setting being used , the type of object being printed, and how the color of the object is specified in the software program. When Color Correction is set to Off, the color is based on the print job information, and no color conversion is implemented.
Note: The Color Samples pages are not useful if the software program does not specify colors with RGB or CMYK combinations. Additionally, certain situations exist in which the software program or the computer operating system adjusts the RGB or CMYK combinations specified in the program through color management. The resulting printed color may not be an exact match of the Color Samples pages.
What are detailed color samples and how do I access them?
Detailed color samples sets are available only through the Embedded Web Server of a network printer. A detailed Color Samples set contains a range of shades that are similar to a user‑defined RGB or CMYK value. The likeness of the colors in the set is dependent on the value entered in the RGB or CMYK Increment box.

To access a detailed Color Samples set from the Embedded Web Server, do the following:
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Configuration > Color Samples > Detailed Options.
3 Select a color conversion table.
4 Enter the RGB or CMYK color number.
5 Enter an increment value from 1 to 255.
6 Click Print.
Step 1 From the printer control panel, make sure the paper type setting is set to Transparency.
Go to step 2. Set the paper type to Transparency.
Is the paper type setting correct?
The problem is solved. Go to step 3.
Reduce the toner darkness, and then resend the print job.
Does the print on the color transparency look lighter?
The problem is solved. Contact customer support.
Make sure you are using a recommended type of color transparency, and then resend the print job.
Does the print on the color transparency look lighter?

The color of the print does not match the color of the original file
The problem is solved. Go to step 2.
a Set Color Correction to Off.
Does the color of the print match the color of the file on the computer screen?
The problem is solved. Contact customer support.
From the Quality menu on the printer control panel, do the following:
a Select Color Correction, and then select Manual. b Select Manual Color, and then select the appropriate color conversion
table for the affected object type. c Resend the print job.
Does the color of the print match the color of the file on the computer screen?
Adjust the color balance.
The problem is solved. Contact customer support.
a From the Color Balance menu on the printer control panel, increase
or decrease the values for cyan, magenta, yellow, and black. b Resend the print job.
Does the print still appear tinted?
The problem is solved. Go to step 2.
a Turn on the printer. b Open a Web browser, and then type the printer IP address.
c Press Enter.
Does the Embedded Web Server open?

The problem is solved. Go to step 3.
Make sure the printer IP address is correct.
a View the printer IP address:
Does the Embedded Web Server open?
Step 3 Check if the network is working.
The problem is solved. Go to step 4.
a Print a network setup page. b Check the first section of the network setup page and confirm that the
status is Connected.
Does the Embedded Web Server open?
The problem is solved. Go to step 5.
Check if the cable connections to the printer and print server are secure.
a Connect the cables properly. For more information, see the setup
documentation that came with the printer. b Open a Web browser, and then type the printer IP address.
c Press Enter.
Does the Embedded Web Server open?
The problem is solved. Contact your system support person.
Temporarily disable the Web proxy servers.
Proxy servers may block or restrict you from accessing certain Web sites including the Embedded Web Server.
Does the Embedded Web Server open?

When you contact customer support, you will need to be able to describe the problem you are experiencing, the message on the printer display, and the troubleshooting steps you have already taken to find a solution.
You need to know your printer model type and serial number. For more information, see the label at the back of the printer. The serial number is also listed on the menu settings page.
Lexmark has various ways to help you solve your printing problem. Visit the Lexmark Web site at http://support.lexmark.com, and then select one of the following:
Tech Library You can browse our library of manuals, support documentation, drivers, and other downloads to help you
solve common problems.
E-mail You can send an e-mail to the Lexmark team, describing your problem. A service representative will respond and provide you with information to solve your problem.
Live chat You can chat directly with a service representative. They can work with you to solve your printer problem or provide assistance through Assisted Service where the service representative can remotely connect to your computer through the Internet to troubleshoot problems, install updates, or complete other tasks to help you successfully use your Lexmark product.
Telephone support is also available. In the U.S. or Canada, call 1-800-539-6275. For other countries or regions, visit http://support.lexmark.com.
Troubleshooting 210

Product name:
Machine type:
Model(s):
The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.
References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.
For Lexmark technical support, visit http://support.lexmark.com.
For information on supplies and downloads, visit www.lexmark.com.
© 2014 Lexmark International, Inc.
All rights reserved.
The Software Program and any related documentation are "Commercial Items," as that term is defined in 48 C.F.R. 2.101, "Computer Software" and "Commercial Computer Software Documentation," as such terms are used in 48 C.F.R. 12.212 or 48 C.F.R. 227.7202, as applicable. Consistent with 48 C.F.R. 12.212 or 48 C.F.R. 227.7202-1 through 227.7207-4, as applicable, the Commercial Computer Software and Commercial Software Documentation are licensed to the U.S. Government end users (a) only as Commercial Items and (b) with only those rights as are granted to all other end users pursuant to the terms and conditions herein.
Lexmark CS510de · September 2014

Lexmark, Lexmark with diamond design, and MarkVision are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.
Mac and the Mac logo are trademarks of Apple Inc., registered in the U.S. and other countries.
PCL® is a registered trademark of the Hewlett-Packard Company. PCL is Hewlett-Packard Company’s designation of a set of printer commands (language) and functions included in its printer products. This printer is intended to be compatible with the PCL language. This means the printer recognizes PCL commands used in various application programs, and that the printer emulates the functions corresponding to the commands.
The following terms are trademarks or registered trademarks of these companies:

CG Times Based on Times New Roman under license from The Monotype Corporation plc, is a product of Agfa Corporation

All other trademarks are the property of their respective owners.
AirPrint and the AirPrint logo are trademarks of Apple, Inc.
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The FCC Class B limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
The manufacturer is not responsible for radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment.
Any questions regarding this compliance information statement should be directed to:
Director of Lexmark Technology & Services Lexmark International, Inc. 740 West New Circle Road Lexington, KY 40550 (859) 232–3000
All licensing notices associated with this product can be viewed from the root directory of the installation software CD.
The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.
1-meter average sound pressure, dBA
Printing 50

1-meter average sound pressure, dBA
Values are subject to change. See www.lexmark.com for current values.
The WEEE logo signifies specific recycling programs and procedures for electronic products in countries of the European Union. We encourage the recycling of our products.
If you have further questions about recycling options, visit the Lexmark Web site at www.lexmark.com for your local sales office phone number.
This product complies with the India E-Waste (Management and Handling) Rules, 2011, which prohibit use of lead, mercury, hexavalent chromium, polybrominated biphenyls, or polybrominated diphenyl ethers in concentrations exceeding 0.1% by weight and 0.01% by weight for cadmium, except for the exemption set in Schedule II of the Rules.
Do not dispose of the printer or supplies in the same manner as normal household waste. Consult your local authorities for disposal and recycling options.
This symbol identifies static-sensitive parts. Do not touch in the areas near these symbols without first touching the metal frame of the printer.
Ready 16

Any Lexmark product bearing the ENERGY STAR emblem on the product or on a start-up screen is certified to comply with Environmental Protection Agency (EPA) ENERGY STAR requirements as configured when shipped by Lexmark.
Ambient operating temperature 15.6 to 32.2°C (60 to 90°F)
Shipping temperature -40 to 43.3°C (-40 to 110°F)
Storage temperature and relative humidity 1 to 35°C (34 to 95°F)
8 to 80% RH
Consumo de energía en operación:
Consumo de energía en modo de espera:
0.2 Wh
Cantidad de producto por unidad de energía consumida:
2.78 páginas / Wh
The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR, Chapter I, Subchapter J for Class I (1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements of IEC 60825-1.
Class I laser products are not considered to be hazardous. The printer contains internally a Class IIIb (3b) laser that is nominally a 7 milliwatt gallium arsenide laser operating in the wavelength of 655-675 nanometers. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service condition.
A laser notice label may be affixed to this printer as shown:
540 Wh

Opasnost - Nevidljivo lasersko zračenje kada su kasete uklonjene i poništena sigurnosna veza. Izbjegavati izlaganje zracima.
NEBEZPEČÍ - Když jsou vyjmuty kazety a je odblokována pojistka, ze zařízení je vysíláno neviditelné laserové záření. Nevystavujte se působení laserového paprsku.
FARE - Usynlig laserstråling, når patroner fjernes, og spærreanordningen er slået fra. Undgå at blive udsat for laserstrålen.
VAARA - Näkymätöntä lasersäteilyä on varottava, kun värikasetit on poistettu ja lukitus on auki. Vältä lasersäteelle altistumista.
ΚΙΝΔΥΝΟΣ - Έκλυση αόρατης ακτινοβολίας laser κατά την αφαίρεση των κασετών και την απασφάλιση της μανδάλωσης. Αποφεύγετε την έκθεση στην ακτινοβολία laser.
VESZÉLY – Nem látható lézersugárzás fordulhat elő a patronok eltávolításakor és a zárószerkezet felbontásakor. Kerülje a lézersugárnak való kitettséget. PERICOLO - Emissione di radiazioni laser invisibili durante la rimozione delle cartucce e del blocco. Evitare l´esposizione al raggio laser.
FARE – Usynlig laserstråling når kassettene tas ut og sperren er satt ut av spill. Unngå eksponering for laserstrålen.
ОПАСНО! Невидимое лазерное излучение при извлеченных картриджах и снятии блокировки. Избегайте воздействия лазерных лучей. Pozor – Nebezpečenstvo neviditeľného laserového žiarenia pri odobratých kazetách a odblokovanej poistke. Nevystavujte sa lúčom.
FARA – Osynlig laserstrålning när patroner tas ur och spärrmekanismen är upphävd. Undvik exponering för laserstrålen.
危险 - 当移除碳粉盒及互锁失效时会产生看不见的激光辐射,请避免暴露在激光光束下。
危険 - カートリッジが取り外され、内部ロックが無効になると、見えないレーザー光が放射されます。 このレーザー光に当たらないようにしてください。
Power consumption
Product power consumption
The following table documents the power consumption characteristics of the product.
Mode Description Power consumption (Watts)
Printing The product is generating hard‑copy output from electronic inputs. 580 (one-sided), 360 (two- sided)
Copy The product is generating hard‑copy output from hard‑copy original documents.
Scan The product is scanning hard‑copy documents. N/A
Ready The product is waiting for a print job. 30
Sleep Mode The product is in a high‑level energy‑saving mode. 3
Hibernate The product is in a low‑level energy‑saving mode. 0.5
Off The product is plugged into an electrical outlet, but the power switch is turned off.
The power consumption levels listed in the previous table represent time-averaged measurements. Instantaneous power draws may be substantially higher than the average.
Values are subject to change. See www.lexmark.com for current values.

This product is designed with an energy-saving mode called Sleep Mode. The Sleep Mode saves energy by lowering power consumption during extended periods of inactivity. The Sleep Mode is automatically engaged after this product is not used for a specified period of time, called the Sleep Mode Timeout.
Factory default Sleep Mode Timeout for this product (in minutes): 20
By using the configuration menus, the Sleep Mode Timeout can be modified between 1 minute and 120 minutes. Setting the Sleep Mode Timeout to a low value reduces energy consumption, but may increase the response time of the product. Setting the Sleep Mode Timeout to a high value maintains a fast response, but uses more energy.
This product is designed with an ultra‑low power operating mode called Hibernate mode. When operating in Hibernate Mode, all other systems and devices are powered down safely.
The Hibernate mode can be entered in any of the following methods:
Factory default Hibernate Timeout for this product in all countries or regions 3 days
The amount of time the printer waits after a job is printed before it enters Hibernate mode can be modified between one hour and one month.
If this product has an off mode which still consumes a small amount of power, then to completely stop product power consumption, disconnect the power supply cord from the electrical outlet.
It is sometimes helpful to calculate the total product energy usage. Since power consumption claims are provided in power units of Watts, the power consumption should be multiplied by the time the product spends in each mode in order to calculate energy usage. The total product energy usage is the sum of each mode's energy usage.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Standard ICES-003.
Cet appareil numérique de classe B est conforme aux exigences de la norme canadienne relative aux équipements pouvant causer des interférences NMB-003.

この装置は、クラス B 情報技術装置です。この装置は、家庭環境で使用することを目的としていますが、この 装置がラジオやテレビジョン受信機に近接して使用されると、受信障害を引き起こすことがあります。
取扱説明書に従って正しい取り扱いをしてください。
VCCI-B
European Community (EC) directives conformity
This product is in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, 2009/125/EC, and 2011/65/EU on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits, the ecodesign of energy-related products, and on the restrictions of use of certain hazardous substances in electrical and electronic equipment.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY. A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950‑1.
This section contains the following regulatory information pertaining to wireless products that contain transmitters, for example, but not limited to, wireless network cards or proximity card readers.
Wireless‑equipped models contain the following modular component(s):
Lexmark Regulatory Type-Model LEX-M01-005; FCC ID:IYLLEXM01005; IC:2376A-M01005
The radiated output power of this device is far below the radio frequency exposure limits of the FCC and other regulatory agencies. A minimum separation of 20 cm (8 inches) must be maintained between the antenna and any persons for this device to satisfy the RF exposure requirements of the FCC and other regulatory agencies.

This device complies with Industry Canada specification RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This device has been designed to operate only with the antenna provided. Use of any other antenna is strictly prohibited per regulations of Industry Canada.
To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.
The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF fields in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada's Web site www.hc-sc.gc.ca/rpb
The term "IC:" before the certification/registration number only signifies that the Industry Canada technical specifications were met.
Cet appareil est conforme à la norme RSS-210 d'Industry Canada. Son fonctionnement est soumis aux deux conditions suivantes :
(1) cet appareil ne doit pas provoquer d'interférences et (2) il doit accepter toute interférence reçue, y compris celles risquant d'altérer son fonctionnement.
Cet appareil a été conçu pour fonctionner uniquement avec l'antenne fournie. L'utilisation de toute autre antenne est strictement interdite par la réglementation d'Industry Canada.
En application des réglementations d'Industry Canada, l'utilisation d'une antenne de gain supérieur est strictement interdite.
Pour empêcher toute interférence radio au service faisant l'objet d'une licence, cet appareil doit être utilisé à l'intérieur et loin des fenêtres afin de garantir une protection optimale.
Si le matériel (ou son antenne d'émission) est installé à l'extérieur, il doit faire l'objet d'une licence.
L'installateur de cet équipement radio doit veiller à ce que l'antenne soit implantée et dirigée de manière à n'émettre aucun champ HF dépassant les limites fixées pour l'ensemble de la population par Santé Canada. Reportez-vous au Code de sécurité 6 que vous pouvez consulter sur le site Web de Santé Canada www.hc-sc.gc.ca/rpb
Le terme « IC » précédant le numéro de d'accréditation/inscription signifie simplement que le produit est conforme aux spécifications techniques d'Industry Canada.
This product is in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, 1999/5/EC, 2009/125/EC, and 2011/65/EU on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits, radio equipment and telecommunications terminal equipment, the ecodesign of energy-related products, and on the restrictions of use of certain hazardous substances in electrical and electronic equipment.

Compliance is indicated by the CE marking.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY. A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950‑1.
Products equipped with 2.4GHz Wireless LAN option are in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, 1999/5/EC, 2009/125/EC, and 2011/65/EU on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits, radio equipment and telecommunications terminal equipment, the ecodesign of energy-related products, and on the restrictions of use of certain hazardous substances in electrical and electronic equipment.
Compliance is indicated by the CE marking.
Operation is allowed in all EU and EFTA countries, but is restricted to indoor use only.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY. A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product may be used in the countries indicated in the table below.
AT BE BG CH CY CZ DE DK EE
EL ES FI FR HR HU IE IS IT
LI LT LU LV MT NL NO PL PT
Česky Společnost Lexmark International, Inc. tímto prohlašuje, že výrobek tento výrobek je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Dansk Lexmark International, Inc. erklærer herved, at dette produkt overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch Hiermit erklärt Lexmark International, Inc., dass sich das Gerät dieses Gerät in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Ελληνική ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Η LEXMARK INTERNATIONAL, INC. ΔΗΛΩΝΕΙ ΟΤΙ ΑΥΤΟ ΤΟ ΠΡΟΪΟΝ ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.

English Hereby, Lexmark International, Inc., declares that this type of equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Español Por medio de la presente, Lexmark International, Inc. declara que este producto cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Eesti Käesolevaga kinnitab Lexmark International, Inc., et seade see toode vastab direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele muudele asjakohastele sätetele.
Suomi Lexmark International, Inc. vakuuttaa täten, että tämä tuote on direktiivin 1999/5/EY oleellisten vaatimusten ja muiden sitä koskevien direktiivin ehtojen mukainen.
Français Par la présente, Lexmark International, Inc. déclare que l'appareil ce produit est conforme aux exigences fondamentales et autres dispositions pertinentes de la directive 1999/5/CE.
Magyar Alulírott, Lexmark International, Inc. nyilatkozom, hogy a termék megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Íslenska Hér með lýsir Lexmark International, Inc. yfir því að þessi vara er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.
Italiano Con la presente Lexmark International, Inc. dichiara che questo questo prodotto è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski Ar šo Lexmark International, Inc. deklarē, ka šis izstrādājums atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių Šiuo Lexmark International, Inc. deklaruoja, kad šis produktas atitinka esminius reikalavimus ir kitas 1999/5/EB direktyvos nuostatas.
Malti Bil-preżenti, Lexmark International, Inc., jiddikjara li dan il-prodott huwa konformi mal-ħtiġijiet essenzjali u ma dispożizzjonijiet oħrajn relevanti li jinsabu fid-Direttiva 1999/5/KE.
Nederlands Hierbij verklaart Lexmark International, Inc. dat het toestel dit product in overeenstemming is met de essentiële
eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Norsk Lexmark International, Inc. erklærer herved at dette produktet er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.
Polski Niniejszym Lexmark International, Inc. oświadcza, że niniejszy produkt jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português A Lexmark International Inc. declara que este este produto está conforme com os requisitos essenciais e outras disposições da Diretiva 1999/5/CE.
Slovensky Lexmark International, Inc. týmto vyhlasuje, že tento produkt spĺňa základné požiadavky a všetky
príslušné ustanovenia smernice 1999/5/ES.
Slovensko Lexmark International, Inc. izjavlja, da je ta izdelek v skladu z bistvenimi zahtevami in ostalimi
relevantnimi določili direktive 1999/5/ES.
Svenska Härmed intygar Lexmark International, Inc. att denna produkt står i överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Elliptic Curve Cryptography (ECC) Cipher Suites for Transport Layer Security (TLS) implemented in the product or service.

The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for TLS Elliptic Curve Cipher Suites with SHA-256/382 and AES Galois Counter Mode (GCM) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for TLS Suite B Profile for Transport Layer Security (TLS) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Addition of the Camellia Cipher Suites to Transport Layer Security (TLS) implemented in the product or service.
The use of certain patents in this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for AES-CCM ECC Cipher Suites for TLS implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for IKE and IKEv2 Authentication Using the Eliptic Curve Digital Signature Algorithm (ECDSA) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Suite B Cryptographic Suites for IPSec implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Algorithms for Internet Key Exchange version 1 (IKEv1) implemented in the product or service.
LEXMARK LED PRINTERS, AND LEXMARK MULTIFUNCTION LASER PRINTERS
This limited warranty applies to the United States and Canada. For customers outside the U.S., refer to the country- specific warranty information that came with your product.
This limited warranty applies to this product only if it was originally purchased for your use, and not for resale, from Lexmark or a Lexmark Remarketer, referred to in this statement as “Remarketer.”
Lexmark warrants that this product:
—Is manufactured from new parts, or new and serviceable used parts, which perform like new parts
—Is, during normal use, free from defects in material and workmanship
If this product does not function as warranted during the warranty period, contact a Remarketer or Lexmark for repair or replacement (at Lexmark's option).
If this product is a feature or option, this statement applies only when that feature or option is used with the product for which it was intended. To obtain warranty service, you may be required to present the feature or option with the product.

If you transfer this product to another user, warranty service under the terms of this statement is available to that user for the remainder of the warranty period. You should transfer proof of original purchase and this statement to that user.
The warranty period starts on the date of original purchase as shown on the purchase receipt and ends 12 months later provided that the warranty period for any supplies and for any maintenance items included with the printer shall end earlier if it, or its original contents, are substantially used up, depleted, or consumed. Fuser Units, Transfer/Transport Units, Paper Feed items, if any, and any other items for which a Maintenance Kit is available are substantially consumed when the printer displays a “Life Warning” or “Scheduled Maintenance” message for such item.
To obtain warranty service you may be required to present proof of original purchase. You may be required to deliver your product to the Remarketer or Lexmark, or ship it prepaid and suitably packaged to a Lexmark designated location. You are responsible for loss of, or damage to, a product in transit to the Remarketer or the Lexmark designated location.
When warranty service involves the exchange of a product or part, the item replaced becomes the property of the Remarketer or Lexmark. The replacement may be a new or repaired item.
The replacement item assumes the remaining warranty period of the original product.
Replacement is not available to you if the product you present for exchange is defaced, altered, in need of a repair not included in warranty service, damaged beyond repair, or if the product is not free of all legal obligations, restrictions, liens, and encumbrances.
As part of your warranty service and/or replacement, Lexmark may update the firmware in your printer to the latest version. Firmware updates may modify printer settings and cause counterfeit and/or unauthorized products, supplies, parts, materials (such as toners and inks), software, or interfaces to stop working. Authorized use of genuine Lexmark products will not be impacted.
Before you present this product for warranty service, remove all print cartridges, programs, data, and removable storage media (unless directed otherwise by Lexmark).
For further explanation of your warranty alternatives and the nearest Lexmark authorized servicer in your area contact Lexmark on the World Wide Web.
Remote technical support is provided for this product throughout its warranty period. For products no longer covered by a Lexmark warranty, technical support may not be available or only be available for a fee.
Lexmark does not warrant uninterrupted or error-free operation of any product or the durability or longevity of prints produced by any product.
Warranty service does not include repair of failures caused by:
—Modification or unauthorized attachments
—Accidents, misuse, abuse or use inconsistent with Lexmark user’s guides, manuals, instructions or guidance
—Unsuitable physical or operating environment
—Maintenance by anyone other than Lexmark or a Lexmark authorized servicer
—Operation of a product beyond the limit of its duty cycle
—Use of printing media outside of Lexmark specifications
—Refurbishment, repair, refilling or remanufacture by a third party of products, supplies or parts

—Products, supplies, parts, materials (such as toners and inks), software, or interfaces not furnished by Lexmark
TO THE EXTENT PERMITTED BY APPLICABLE LAW, NEITHER LEXMARK NOR ITS THIRD PARTY SUPPLIERS OR REMARKETERS MAKE ANY OTHER WARRANTY OR CONDITION OF ANY KIND, WHETHER EXPRESS OR IMPLIED, WITH RESPECT TO THIS PRODUCT, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND SATISFACTORY QUALITY. ANY WARRANTIES THAT MAY NOT BE DISCLAIMED UNDER APPLICABLE LAW ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. NO WARRANTIES, EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD. ALL INFORMATION, SPECIFICATIONS, PRICES, AND SERVICES ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE.
Your sole remedy under this limited warranty is set forth in this document. For any claim concerning performance or nonperformance of Lexmark or a Remarketer for this product under this limited warranty, you may recover actual damages up to the limit set forth in the following paragraph.
Lexmark's liability for actual damages from any cause whatsoever will be limited to the amount you paid for the product that caused the damages. This limitation of liability will not apply to claims by you for bodily injury or damage to real property or tangible personal property for which Lexmark is legally liable. IN NO EVENT WILL LEXMARK BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, INCIDENTAL DAMAGE, OR OTHER ECONOMIC OR CONSEQUENTIAL DAMAGES. This is true even if you advise Lexmark or a Remarketer of the possibility of such damages. Lexmark is not liable for any claim by you based on a third party claim.
This limitation of remedies also applies to claims against any Suppliers and Remarketers of Lexmark. Lexmark's and its Suppliers' and Remarketers' limitations of remedies are not cumulative. Such Suppliers and Remarketers are intended beneficiaries of this limitation.
Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or limitation of incidental or consequential damages, so the limitations or exclusions contained above may not apply to you.
This limited warranty gives you specific legal rights. You may also have other rights that vary from state to state.







Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.