
User's Guide
Machine type(s):
Model(s):


Connect the power cord directly to an appropriately rated and properly grounded electrical outlet that is near the product and easily accessible.
Do not place or use this product near water or wet locations.
This product uses a printing process that heats the print media, and the heat may cause the media to release emissions. You must understand the section in your operating instructions that discusses the guidelines for selecting print media to avoid the possibility of harmful emissions.
Use only the power cord provided with this product or the manufacturer's authorized replacement.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
This product is designed, tested, and approved to meet strict global safety standards with the use of specific manufacturer's components. The safety features of some parts may not always be obvious. The manufacturer is not responsible for the use of other replacement parts.
Safety information 6

CAUTION—POTENTIAL INJURY: Do not cut, twist, bind, crush, or place heavy objects on the power cord. Do not subject the power cord to abrasion or stress. Do not pinch the power cord between objects such as furniture and walls. If any of these things happen, a risk of fire or electrical shock results. Inspect the power cord regularly for signs of such problems. Remove the power cord from the electrical outlet before inspecting it.
Refer service or repairs, other than those described in the user documentation, to a professional service person.
CAUTION—TIPPING HAZARD: Floor-mounted configurations require additional furniture for stability. You must use either a printer stand or printer base if you are using a high-capacity input tray, a duplex unit and an input option, or more than one input option. If you purchased a multifunction printer (MFP) that scans, copies, and faxes, you may need additional furniture. For more information, see www.lexmark.com/multifunctionprinters.
SAVE THESE INSTRUCTIONS.
Safety information 7

Learning about the printer 8
Finding information about the printer

Learning about the printer 9
When selecting a location for the printer, leave enough room to open trays, covers, and doors. If you plan to install any options, then leave enough room for them also. It is important to:

Learning about the printer 10



Learning about the printer 11

You can configure your basic printer by adding optional trays. A 2,000-sheet high‑capacity feeder and a finisher bin can also be added.



Learning about the printer 12


The finisher bin can either be one of the following:
CAUTION—TIPPING HAZARD: Floor‑mounted configurations require additional furniture for stability. You must use either a printer stand or printer base if you are using a high‑capacity input tray, a duplex unit and an input option, or more than one input option. If you purchased a multifunction printer (MFP) that scans, copies, and faxes, you may need additional furniture. For more information, see www.lexmark.com/multifunctionprinters.

Learning about the printer 13
1 2 3 4


4 GHI 5 JKL 6 MNO
7 PQRS 8 TUV 9 WXYZ

1 Display View printing options as well as status and error messages.
2 Home Navigate back to the home screen.
3 Keypad Enter numbers, letters, or symbols.
4 Sleep button Enable Sleep Mode or Hibernate Mode.
5 Indicator light View the status of the printer.
6 Stop/Cancel Stop all printer activity.
7 USB port Connect a flash drive into the printer USB port.
0 # · Use To

Understanding the home screen 14
Understanding the home screen
When the printer is turned on, the display shows a basic screen, referred to as the home screen. Use the home screen buttons and icons to initiate an action.

123.123.123.123
5 6 7 8
1 Change Language Change the primary language of the printer.
2 Bookmarks Create, organize, and save a set of bookmarks (URLs) into a tree view of folders and file links.
3 Held Jobs Display all current held jobs.
4 USB or USB Thumbdrive
View, select, or print photos and documents from a flash drive.
5 Menus Access printer menus.
8 Tips Open a context‑sensitive Help information on the touch screen.
Touch To

Understanding the home screen 15
This may also appear on the home screen:
Search Held Jobs Search current held jobs.
If an attendance message affects a function, then this icon appears and the red indicator light blinks.
The IP address of your network printer is located at the top left corner of the home screen and appears as four sets of numbers separated by periods. You can use the IP address when accessing the Embedded Web Server so you can view and remotely configure printer settings even when you are not physically near the printer.
1 2 3 4

5 6 7 8 9 10
Scroll up.

Understanding the home screen 16
Delete the file you selected.
Scroll to the left.
Scroll to the right.
5 Right scroll increase
Scroll to another value in increasing order.
6 Left scroll decrease
Scroll to another value in decreasing order.
Scroll down.
Save a setting.
Navigate back to the previous screen.

Setting up and using the home screen applications 17
The Embedded Web Server is the printer Web page that lets you view and remotely configure printer settings even when you are not physically near the printer.
2 Open a Web browser, and then type the printer IP address in the address field.
3 Press Enter.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Home screen customization.
A list of basic printer functions appears.
3 Select the check boxes to specify which icons appear on the printer home screen.
4 Click Submit.

Setting up and using the home screen applications 18
Your printer comes with preinstalled home screen applications. You can activate and set up these applications using the Embedded Web Server. To access the Embedded Web Server, see “Accessing the Embedded Web Server” on page 17.
For detailed information about configuring and using the home screen applications, go to the Lexmark support Web site at http://support.lexmark.com.

The application lets you customize the background and idle screen of your printer home screen.
1 From the home screen, navigate to:
Change Background > select background to use

The application helps you simplify and streamline work processes by letting you quickly find and print frequently used online forms directly from the home screen.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Device Solutions > Solutions (eSF) > Forms and Favorites.
3 Define the bookmarks, and then customize the settings.
4 Click Apply.
To use the application, touch Forms and Favorites on the printer home screen, and then navigate through form categories, or search for forms based on a form number, name, or description.
Icon Description · 2 Touch · Icon Description

Setting up and using the home screen applications 19
The application lets you easily manage energy consumption, noise, toner, and paper usage settings to help reduce the environmental impact of your printer.
The application lets you create and display a customized slide show on the touch screen of your printer. You can load images either from a flash drive or through the printer Embedded Web Server.
This application shows the printer control panel on your computer screen and lets you interact with the printer control panel, even when you are not physically near the network printer. From your computer screen, you can view the printer status, release held print jobs, create bookmarks, and do other print-related tasks you might normally do while standing at the network printer.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Device Solutions > Solutions (eSF) > Remote Operator Panel.
3 Select the Enabled check box, and then customize the settings.
4 Click Apply.
To use the application, from the Embedded Web Server, click Applications > Remote Operator Panel > Launch VNC Applet.
Icon Description · Icon Description

Setting up and using the home screen applications 20
You can export configuration settings into a text file, and then import the file to apply the settings to other printers.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Export or import a configuration file for one or multiple applications.
a Navigate to:
Settings > Apps > Apps Management > select an application > Configure b Export or import the configuration file.
a Click Settings > Import/Export. b Export or import a configuration file.

Additional printer setup 21
Turning on the printer
1 Open the front door.

2 Press the printer power switch.

3 Close the front door.


Additional printer setup 22
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.

Additional printer setup 23
1 Turn the screws counterclockwise to loosen them.

2 Pull the system board forward to remove it.

3 Use the following illustration to locate the appropriate connectors.

Additional printer setup 24

2 Firmware and flash memory card connectors
3 Memory card connectors
4 Push the system board back into place.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
An optional memory card can be purchased separately and attached to the system board.
1 Access the system board.
For more information, see “Accessing the system board” on page 22.
2 Unpack the memory card.
1 ISP connector

Additional printer setup 25
3 On the system board, open the memory card connector latches.

4 Align the notch on the memory card to the ridge on the connector.

1 Notch · 2 Ridge

Additional printer setup 26
5 Push the memory card into the connector until it clicks into place.
The system board has two connections for an optional flash memory or firmware card. Only one of each may be installed, but the connectors are interchangeable.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Access the system board.
For more information, see “Accessing the system board” on page 22.
2 Unpack the card.

Additional printer setup 27
3 Holding the card by its sides, align the plastic pins on the card with the holes on the system board.

4 Push the card firmly into place.

The system board supports one optional Lexmark Internal Solutions Port (ISP).
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Plastic pins · 2 Metal pins

Additional printer setup 28
1 Access the system board.
For more information, see “Accessing the system board” on page 22.
2 Remove the printer hard disk.
For more information, see “Removing a printer hard disk” on page 34
3 Unpack the ISP kit.

2 Screws for the ISP solution
3 Screws for the plastic bracket
4 Use the provided screws to attach the plastic bracket to the ISP solution.

1 ISP solution · 4 Plastic bracket

Additional printer setup 29
5 Use the provided screw to attach the ISP solution to the system board cage.

6 Connect the ISP solution interface cable into the receptacle of the system board.


Additional printer setup 30
7 Firmly connect the ISP solution to the system board cage using two screws.

CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Access the system board.
For more information, see “Accessing the system board” on page 22.
2 Unpack the printer hard disk.

Additional printer setup 31
3 Locate the appropriate connector on the system board.

To install a printer hard disk onto the ISP:
a Using a flathead screwdriver, loosen the screws.

b Remove the screws attached to the printer hard disk mounting bracket, and then remove the bracket.

Additional printer setup 32
c Align the standoffs of the printer hard disk to the holes in the ISP, and then press down on the printer
hard disk until the standoffs are in place.

d Insert the plug of the printer hard disk interface cable into the receptacle of the ISP.


Additional printer setup 33
To install a printer hard disk directly on the system board:
a Align the standoffs of the printer hard disk to the holes in the system board, and then press down on
the printer hard disk until the standoffs are in place.

b Use the two provided screws to attach the printer hard disk mounting bracket.

c Insert the plug of the printer hard disk interface cable into the receptacle of the system board.

Additional printer setup 34


Additional printer setup 35
1 Access the system board.
For more information, see “Accessing the system board” on page 22.
2 Unplug the printer hard disk interface cable from the system board, leaving the cable attached to the printer hard disk. To unplug the cable, squeeze the paddle at the plug of the interface cable to disengage the latch before pulling the cable out.


Additional printer setup 36
3 Remove the screws while holding the printer hard disk in place, and then remove the printer hard disk.

4 Set aside the printer hard disk.
CAUTION—TIPPING HAZARD: Floor-mounted configurations require additional furniture for stability. You must use either a printer stand or printer base if you are using a high-capacity input tray, a duplex unit and an input option, or more than one input option. If you purchased a multifunction printer (MFP) that scans, copies, and faxes, you may need additional furniture. For more information, see www.lexmark.com/multifunctionprinters.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.

Additional printer setup 37
Install the printer and any optional trays or finishers you have purchased in the following order:
Using a one‑tray module
Using a three‑tray module
Using a tandem‑tray module
For information on installing a one‑tray module, three‑tray module, tandem‑tray module, high‑capacity feeder, or any of the finishers, see the setup documentation that came with the option.
The printer supports the following optional trays:
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
CAUTION—TIPPING HAZARD: Floor-mounted configurations require additional furniture for stability. You must use either a printer stand or printer base if you are using a high-capacity input tray, a duplex unit and an input option, or more than one input option. If you purchased a multifunction printer (MFP) that scans, copies, and faxes, you may need additional furniture. For more information, see www.lexmark.com/multifunctionprinters.

Additional printer setup 38
1 Unpack the optional tray, and then remove all packing material.
2 Place the tray near the printer.
3 Turn off the printer.
4 Align the printer with the tray, and then lower the printer into place.



Additional printer setup 39

1 Tandem‑tray module
2 2,000‑sheet high‑capacity feeder
5 Turn the printer back on.
6 Set the printer software to recognize the optional tray. For more information, see “Adding available options in the print driver” on page 42.
Connect the printer to the computer using a USB cable or Ethernet cable.
Be sure to match the following:

Additional printer setup 40

Once all hardware and software options are installed and the printer is turned on, verify that the printer is set up correctly by printing the following:

Additional printer setup 41
From the home screen, navigate to:
> Reports > Menu Settings Page
If the printer is attached to a network, then print a network setup page to verify the network connection. This page also provides important information that aids network printing configuration.
1 From the home screen, navigate to:
> Reports > Network Setup Page
2 Check the first section of the network setup page, and confirm that the status is Connected.
If the status is Not Connected, then the LAN drop may not be active, or the network cable may be malfunctioning. Consult a system support person for a solution, and then print another network setup page.
2 Double‑click the software installer package.
Wait for the installation dialog to appear.
If you are using a Software and Documentation CD and the installation dialog does not appear, then do the following:
From the Search charm, type run, and then navigate to:
Apps list > Run > type D:\setup.exe > OK.
or click Start, and then click Run. b In the Start Search or Run dialog, type D:\setup.exe.
a Click

Additional printer setup 42
c Press Enter, or click OK.
Click the CD icon on the desktop.
3 Click Install, and then follow the instructions on the computer screen.
1 Open the printers folder.
From the Search charm, type run, and then navigate to:
Run > type control printers > OK
In Windows 7 or earlier
, or click Start and then click Run. b Type control printers.
c Press Enter, or click OK.
3 Navigate to the Configuration tab, and then select Update Now ‑ Ask Printer.
4 Apply the changes.
1 From System Preferences in the Apple menu, navigate to your printer, and then select Options & Supplies.
2 Navigate to the list of hardware options, and then add any installed options.
3 Apply the changes.
In Windows 8 · a Click

Additional printer setup 43
To configure your printer to connect to an Ethernet network, organize the following information before you begin:
You will need an Ethernet cable to connect the printer to the network and an available port where the printer can physically connect to the network. Use a new network cable when possible to avoid potential problems caused by a damaged cable.
Make sure you have the following information before setting up the printer on a wireless network:
Some ad hoc networks will also require the automatic setting. Check with your system support person if you are not sure which channel to select.

Additional printer setup 44
If your network uses more than one WEP key, then enter up to four in the provided spaces. Select the key currently in use on the network by selecting the default WEP transmit key. – WPA or WPA2 preshared key or passphrase
WPA includes encryption as an additional layer of security. The choices are AES or TKIP. Encryption must be set for the same type on the router and on the printer, or the printer will not be able to communicate on the network. – 802.1X–RADIUS
If you are installing the printer on an 802.1X network, then you may need the following:
If your wireless network does not use any type of security, then you will not have any security information.
– If you do not know the SSID of the network that your computer is connected to, then launch the wireless
utility of the computer network adapter, and then look for the network name. If you cannot find the SSID or the security information for your network, then see the documentation that came with the access point or contact your system support person. – To find the WPA/WPA2 preshared key or passphrase for the wireless network, see the documentation
that came with the access point, see the Embedded Web Server associated with the access point, or consult your system support person.
Before installing the printer on a wireless network, make sure:
1 Connect the power cord to the printer, then to a properly grounded electrical outlet, and then turn on the printer.

Additional printer setup 45


3 Double‑click the software installer package.
Wait for the installation dialog to appear.
If you are using the Software and Documentation CD and the installation dialog does not appear, then do the following:
From the Search charm, type run, and then navigate to:
Apps list > Run > type D:\setup.exe > OK
or click Start, and then click Run. b In the Start Search or Run dialog, type D:\setup.exe.
c Press Enter or click OK.
4 Click Install, and then follow the instructions on the computer screen.
5 Select Wireless connection when asked to choose a connection type.
a Click

Additional printer setup 46
6 From the Wireless Configuration dialog, select Guided Setup (Recommended).
7 Temporarily connect a USB cable between the computer on the wireless network and the printer.
8 Follow the instructions on the computer screen.
1 Connect the power cord to the printer, then to a properly grounded electrical outlet, and then turn on the printer.


2 Locate the printer MAC address. a From the printer control panel, navigate to:
> Reports > > Network Setup Page > or
> Reports > Network Setup Page b In the Standard Network Card section, look for UAA (MAC).

Additional printer setup 47
1 Access the AirPort options:
In Mac OS X version 10.5 or later
From the Apple menu, navigate to either of the following:
In Mac OS X version 10.4
From the Finder, navigate to:
Applications > Internet Connect > AirPort
2 From the Network Name pop‑up menu, select print server [yyyyyy], where the y’s are the last six digits of the MAC address located on the MAC address sheet.
3 Open a Web browser.
4 From the Bookmarks menu, select Show or Show All Bookmarks.
5 Under COLLECTIONS, select Bonjour or Rendezvous, and then double‑click the printer name.
6 From the Embedded Web Server, navigate to the location of the wireless settings information.
1 Type the network name (SSID) in the appropriate field.
2 Select Infrastructure as your Network Mode setting if you are using an access point (wireless router).
3 Select the type of security you want to use to protect the wireless network.
4 Enter the security information necessary for the printer to connect to the wireless network.
5 Click Submit.
6 Open the AirPort application on the computer:
In Mac OS X version 10.5 or later
From the Apple menu, navigate to either of the following:
In Mac OS X version 10.4
From the Finder, navigate to:
Applications > Internet Connect > AirPort
7 From the Network pop‑up menu, select the name of the wireless network.

Additional printer setup 48
To print on a network printer, each Macintosh user must install a custom printer driver file and create a print queue in the Printer Setup Utility or Print Center.
1 Install a printer driver file on the computer: a Obtain a copy of the software installer package.
c Follow the instructions on the computer screen. d Select a destination, and then click Continue. e From the Easy Install screen, click Install.
f Type the user password, and then click OK. All necessary applications are installed in the computer. g Click Close when the installation is complete.
In Mac OS X version 10.5 or later
In Mac OS X version 10.4
1 From the Finder, navigate to: Applications > Utilities 2 Double‑click Printer Setup Utility or Print Center. 3 From the Printer List, choose Add, and then click IP Printer. 4 Type the IP address of the printer in the address field, and then click Add. b For AppleTalk printing:

Additional printer setup 49
In Mac OS X version 10.5
1 From the Apple menu, navigate to: System Preferences > Print & Fax 2 Click +, and then navigate to: AppleTalk > select the printer from the list > Add
In Mac OS X version 10.4
1 From the Finder, navigate to: Applications > Utilities 2 Double‑click Printer Setup Utility or Print Center. 3 From the Printer List, click Add. 4 Click Default Browser tab > More Printers. 5 From the first pop‑up menu, select AppleTalk. 6 From the second pop‑up menu, select Local AppleTalk Zone. 7 Select the printer from the list, and then click Add.
1 Open the printers folder.
2 From the shortcut menu of the printer with the new ISP, open the printer properties.
3 Configure the port from the list.
4 Update the IP address.
5 Apply the changes.
1 From System Preferences in the Apple menu, navigate to the list of printers, and then select + > IP.
2 Type the IP address in the address field.
3 Apply the changes.
After installing the serial or communication (COM) port, configure the printer and the computer.

Additional printer setup 50
1 Set the parameters in the printer. a From the control panel, navigate to the menu for the port settings. b Locate the menu for the serial port settings, and then adjust the settings, if necessary.
c Save the settings.
2 From your computer, open the printers folder, and then select your printer.
3 Open the printer properties, and then select the COM port from the list.
4 Set the COM port parameters in Device Manager.
Use the Run dialog box to open the command prompt, and then type devmgmt.msc.

Minimizing your printer's environmental impact 51
Lexmark is committed to environmental sustainability and is continually improving its printers to reduce their impact on the environment. We design with the environment in mind, engineer our packaging to reduce materials, and provide collection and recycling programs. For more information, see:
By selecting certain printer settings or tasks, you may be able to reduce your printer's impact even further. This chapter outlines the settings and tasks that may yield a greater environmental benefit.
Studies show that as much as 80% of the carbon footprint of a printer is related to paper usage. You can significantly reduce your carbon footprint by using recycled paper and the following printing suggestions, such as printing on both sides of the paper and printing multiple pages on one side of a sheet of paper.
For information on how you can quickly save paper and energy using one printer setting, see “Using Eco‑Mode” on page 52.
As an environmentally conscious company, Lexmark supports the use of recycled office paper produced specifically for use in laser/LED printers. For more information on recycled papers that work well with your printer, see “Using recycled paper and other office papers” on page 71.
If your printer model supports two‑sided printing, then you can control whether print appears on one or two sides of the paper.
You can print up to 16 consecutive pages of a multiple‑page document onto one side of a single sheet of paper by setting multiple page printing (N‑Up) for the print job.

Minimizing your printer's environmental impact 52
Before printing or making multiple copies of a document:
Correctly set the paper type and size to avoid paper jams. For more information, see “Avoiding jams” on page 179.
1 Type the printer IP address into the address field of your Web browser.
If you do not know the IP address of the printer, you can:
2 Click Settings > General Settings > Eco‑Mode > select a setting > Submit.
Off Use factory default settings for all settings associated with Eco‑Mode. This setting supports the performance specifications of your printer.
Energy Reduce energy use, especially when the printer is idle.
Energy/Paper Use all the settings associated with Energy mode and Paper mode.
To select a Quiet Mode setting using the Embedded Web Server:
1 Type the printer IP address into the address field of your Web browser.
If you do not know the IP address of the printer, you can:
2 Click Settings > General Settings > Quiet Mode > select a setting > Submit.
Choose To

Minimizing your printer's environmental impact 53
Use factory default settings. This setting supports the performance specifications of your printer.
On Reduce printer noise.
1 From the home screen, navigate to:
> Settings > General Settings > Timeouts > Sleep Mode
2 In the Sleep Mode field, select the number of minutes the printer is idle before it enters Sleep mode.
3 Apply the changes.
Hibernate is an ultra‑low power operating mode. When operating in Hibernate mode, all other systems and devices are powered down safely.
1 Type the printer IP address into the address field of your Web browser.
If you do not know the IP address of the printer, you can:
2 Click Settings > General Settings > Sleep Button Settings.
3 From the Press Sleep Button or Press and Hold Sleep Button drop‑down, select Hibernate.
4 Click Submit.
Choose To · Off

Minimizing your printer's environmental impact 54
1 From the home screen, navigate to:
> Settings > General Settings > Press Sleep Button or Press and Hold Sleep Button > Hibernate
To save energy, or if you have trouble reading from the display, adjust the brightness of the display.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Select Settings > General Settings.
3 In the Screen Brightness field, enter the brightness percentage you want for the display.
4 Apply the changes.
1 From the home screen, navigate to:
> Settings > General Settings
2 In the Screen Brightness field, enter the brightness percentage you want for the display.
3 Apply the changes.
To return Lexmark products for recycling:
1 Go to www.lexmark.com/recycle.
2 Find the product type you want to recycle, and then select your country or region from the list.
3 Follow the instructions on the computer screen.
2 Touch

Minimizing your printer's environmental impact 55
Lexmark continually strives to minimize packaging. Less packaging helps to ensure that Lexmark printers are transported in the most efficient and environmentally sensitive manner and that there is less packaging to dispose of. These efficiencies result in fewer greenhouse emissions, energy savings, and natural resource savings.
Lexmark cartons are 100% recyclable where corrugated recycling facilities exist. Facilities may not exist in your area.
The foam used in Lexmark packaging is recyclable where foam recycling facilities exist. Facilities may not exist in your area.
When you return a cartridge to Lexmark, you can reuse the box that the cartridge came in. Lexmark will recycle the box.
Lexmark Cartridge Collection Program diverts millions of Lexmark cartridges from landfills annually by making it both easy and free for Lexmark customers to return used cartridges to Lexmark for reuse or recycling. One hundred percent of the empty cartridges returned to Lexmark are either reused or demanufactured for recycling. Boxes used to return the cartridges are also recycled.
To return Lexmark cartridges for reuse or recycling, follow the instructions that came with your printer or cartridge and use the prepaid shipping label. You can also do the following:
1 Go to www.lexmark.com/recycle.
2 From the Toner Cartridges section, select your country or region.
3 Follow the instructions on the computer screen.

Loading paper and specialty media 56
Setting the paper size and type
The Paper Size setting is automatically sensed according to the position of the paper guides in each tray except the multipurpose feeder. The Paper Size setting for the multipurpose feeder must be set manually from the Paper Size menu. The Paper Type setting must be set manually for all trays that do not contain plain paper.
From the home screen navigate to:
> Paper Menu > Paper Size/Type > select a tray > select the paper size or type >
The factory default Paper Type setting is Plain Paper.
The Universal Paper Size is a user‑defined setting that lets you print on paper sizes that are not preset in the printer menus. Set paper size to Universal for the specified tray when the size you want is not available from the Paper Size menu. Then, specify all of the following Universal size settings for your paper:
The following are the supported Universal sizes:
1 From the home screen, navigate to:
> Paper Menu > Universal Setup > Units of Measure > select a unit of measure
2 Touch Portrait Width or Portrait Height.
3 Select the width or height, and then touch
The printer has one standard 520‑sheet tray (Tray 1), and may have one or more optional 520‑sheet trays. All 520‑sheet trays support the same paper sizes and types.

Loading paper and specialty media 57
1 Pull the tray out.



Loading paper and specialty media 58
2 Squeeze and then slide the width guide to the correct position for the paper size loaded.

3 Squeeze and then slide the length guide to the correct position for the paper size loaded.

4 Flex the sheets back and forth to loosen them. Do not fold or crease the paper. Straighten the edges on a level surface.

5 Load the paper stack with the recommended print side faceup.

Loading paper and specialty media 59

6 Insert the tray.

7 From the printer control panel, verify the Paper Size and Paper Type setting for the tray based on the paper you loaded.
The 850‑ and 1,150‑sheet trays support the same paper sizes and types, and require the same process for loading paper.

Loading paper and specialty media 60
1 Pull the tray out.

2 Squeeze and then slide the length guide to the correct position for the paper size you are loading.

3 Flex the sheets back and forth to loosen them. Do not fold or crease the paper. Straighten the edges on a level surface.


Loading paper and specialty media 61
4 Load the paper stack with the recommended print side faceup.
5 Insert the tray.
6 From the printer control panel, verify the Paper Size and Paper Type setting for the tray based on the paper you loaded.

Loading paper and specialty media 62
The high‑capacity feeder can hold up to 2,000 sheets of letter‑, A4‑, and legal‑size paper (80 g/m2 or 20 lb).
1 Pull the tray out.

2 Adjust the width guide as necessary.


Loading paper and specialty media 63
3 Flex the sheets back and forth to loosen them. Do not fold or crease the paper. Straighten the edges on a level surface.

4 Load paper into the tray with the print side faceup.



Loading paper and specialty media 64
5 Insert the tray.
The multipurpose feeder can hold several sizes and types of print media, such as transparencies, labels, card stock, and envelopes. It can be used for single-page or manual printing, or as an additional tray.
The multipurpose feeder can hold approximately:
The multipurpose feeder accepts paper or specialty media within the following dimensions:
1 Pull down the multipurpose feeder door.


Loading paper and specialty media 65
2 For paper or specialty media that is longer than letter-size paper, gently pull the extension until it is fully extended.

3 Flex the sheets of paper or specialty media back and forth to loosen them. Do not fold or crease them. Straighten the edges on a level surface.


Loading paper and specialty media 66
4 Push the paper pick tab, and then load the paper or specialty media. Slide the stack gently into the multipurpose feeder until it comes to a stop, and then release the paper pick tab.



Loading paper and specialty media 67
5 Adjust the width guide to lightly touch the edge of the stack. Make sure the paper or specialty media fits loosely in the multipurpose feeder, lies flat, and is not bent or wrinkled.

6 From the printer control panel, set the Paper Size and Paper Type for the multipurpose feeder (MP Feeder Size and MP Feeder Type) based on the paper or specialty media loaded.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu.
4 Click Submit.
Link exit bins to create a single output source. The printer automatically uses the next available bin as the output source.

Loading paper and specialty media 68
The standard exit bin holds up to 550 sheets of 20‑lb paper. If you need additional output capacity, you can purchase other optional exit bins.
1 From the home screen, navigate to:
> Paper Menu > Bin Setup
2 Touch the bin or bins you want to link, and then touch Configure Bins > Link.
If the printer is on a network, you can use the Embedded Web Server to define a name other than Custom Type [x] for each of the custom paper types loaded into the printer.
1 Type the printer IP address into the address field of your Web browser.
2 Click Settings > Paper Menu > Custom Name > type a name > Submit.
3 Click Custom Types > select a paper type > Submit.
1 From the home screen, navigate to:
> Paper Menu > Paper Size/Type
2 Select the tray number or MP Feeder Type.
3 Touch the left or right arrow until Custom Type [x] or another custom name appears.
If the printer is on a network, then you can use the Embedded Web Server to define a name other than Custom Type [x] for each of the custom paper types loaded into the printer.
1 Type the printer IP address in the address field of your Web browser.
2 Click Settings > Paper Menu > Custom Types > select the custom name you want to configure > select a paper or specialty media type > Submit.
4 Touch

Paper and specialty media guide 69
The following paper characteristics affect print quality and reliability. Consider these characteristics when evaluating new paper stock.
The printer trays can automatically feed paper weights from 60 to 300 g/m2 (16–80 lb bond) grain long. Paper lighter than 60 g/m2 (16 lb) might not be stiff enough to feed properly, causing jams. For best performance, use 75 g/m2 (20 lb bond) grain long paper. For paper smaller than 182 x 257 mm (7.2 x 10.1 in.), we recommend 90 g/m2 (24 lb) or heavier paper.
Curl is the tendency for paper to curl at its edges. Excessive curl can cause paper feeding problems. Curl can occur after the paper passes through the printer, where it is exposed to high temperatures. Storing paper unwrapped in hot, humid, cold, or dry conditions, even in the trays, can contribute to paper curling prior to printing and can cause feeding problems.
Paper smoothness directly affects print quality. If paper is too rough, then toner cannot fuse to it properly. If paper is too smooth, then it can cause paper feeding or print quality issues. Always use paper between 100 and 300 Sheffield points; however, smoothness between 150 and 200 Sheffield points produces the best print quality.
The amount of moisture in paper affects both print quality and the ability of the printer to feed the paper correctly. Leave paper in its original wrapper until it is time to use it. This limits the exposure of paper to moisture changes that can degrade its performance.

Paper and specialty media guide 70
Store paper in its original wrapper in the same environment as the printer for 24 to 48 hours before printing. Extend the time to several days if the storage or transportation environment is very different from the printer environment. Thick paper may also require a longer conditioning period.
Grain refers to the alignment of the paper fibers in a sheet of paper. Grain is either grain long, running the length of the paper, or grain short, running the width of the paper.
For 60–135 g/m2 (16–36 lb bond) paper, grain long paper is recommended. For papers heavier than 135 g/m2, grain short is recommended.
Most high‑quality xerographic paper is made from 100% chemically treated pulped wood. This content provides the paper with a high degree of stability resulting in fewer paper feeding problems and better print quality. Paper containing fibers such as cotton can negatively affect paper handling.
The following paper types are not recommended for use with the printer:
Using appropriate paper prevents jams and helps ensure trouble‑free printing.
To help avoid jams and poor print quality:

Paper and specialty media guide 71
Use these guidelines when selecting preprinted forms and letterhead:
Use papers printed with heat‑resistant inks designed for use in xerographic copiers. The ink must be able to withstand temperatures up to 190°C (374°F) without melting or releasing hazardous emissions. Use inks that are not affected by the resin in toner. Inks that are oxidation‑set or oil‑based generally meet these requirements; latex inks might not. When in doubt, contact the paper supplier.
Preprinted papers such as letterhead must be able to withstand temperatures up to 190°C (374°F) without melting or releasing hazardous emissions.
As an environmentally conscientious company, Lexmark supports the use of recycled paper produced specifically for use in laser (electrophotographic) printers.
While no blanket statement can be made that all recycled paper will feed well, Lexmark consistently tests papers that represent recycled cut size copier papers available on the global market. This scientific testing is conducted with rigor and discipline. Many factors are taken into consideration both separately and as a whole, including the following:
Recycled papers are better than ever; however, the amount of recycled content in a paper affects the degree of control over foreign matter. And while recycled papers are one good path to printing in an environmentally responsible manner, they are not perfect. The energy required to de-ink and deal with additives such as colorants and “glue” often generates more carbon emissions than does normal paper production. However, using recycled papers enables better resource management overall.
Lexmark concerns itself with the responsible use of paper in general based on life cycle assessments of its products. To gain a better understanding of the impact of printers on the environment, the company commissioned a number of life cycle assessments and found that paper was identified as the primary contributor (up to 80%) of carbon emissions caused throughout the entire life of a device (from design to end-of-life). This is due to the energy-intensive manufacturing processes required to make paper.
Thus, Lexmark seeks to educate customers and partners on minimizing the impact of paper. Using recycled paper is one way. Eliminating excessive and unnecessary paper consumption is another. Lexmark is well- equipped to help customers minimize printing and copying waste. In addition, the company encourages purchasing paper from suppliers who demonstrate their commitment to sustainable forestry practices.

Paper and specialty media guide 72
Lexmark does not endorse specific suppliers, although a converter’s product list for special applications is maintained. However, the following paper choice guidelines will help alleviate the environmental impact of printing:
1 Minimize paper consumption.
2 Be selective about the origin of wood fiber. Buy from suppliers who carry certifications such as the Forestry Stewardship Council (FSC) or The Program for the Endorsement of Forest Certification (PEFC). These certifications guarantee that the paper manufacturer uses wood pulp from forestry operators that employ environmentally and socially responsible forest management and restoration practices.
3 Choose the most appropriate paper for printing needs: normal 75 or 80 g/m2 certified paper, lower weight paper, or recycled paper.
Test results indicate that the following paper types are at risk for use with laser printers:
For more information about Lexmark, visit www.lexmark.com. General sustainability-related information can be found at the Environmental Sustainability link.
Use these paper storage guidelines to help avoid jams and uneven print quality:

Paper and specialty media guide 73
The following tables provide information on standard and optional paper sources and the sizes, types, and weights of paper they support.

3 Paper size is supported if set to metric.
4 Paper size is supported if set to US.
5 Paper size is supported if loaded in the short‑edge orientation. The short edge of the paper enters the printer first.
6 Paper size is supported if loaded in the long‑edge orientation. The long edge of the paper enters the printer first.
7 This is applicable only to the optional 520‑sheet tray.

Paper and specialty media guide 74
Paper size and dimension 520‑sheet tray
2,000‑sheet drawer MP feeder Manual paper
305 x 457 mm (12 x 18 in.)
216 x 340 mm (8.5 x 13.4 in.)
216 x 330 mm (8.5 x 13 in.)
140 x 216 mm (5.5 x 8.5 in.)
7 3/4 Envelope (Monarch)
98 x 191 mm (3.875 x 7.5 in.)
9 Envelope 98 x 226 mm (3.875 x 8.9 in.) X
105 x 241 mm (4.12 x 9.5 in.)
DL Envelope 110 x 220 mm (4.33 x 8.66 in.) X X 2 X 2 X
162 x 229 mm (6.38 x 9.01 in.)
B5 Envelope 176 x 250 mm (6.93 x 9.84 in.) X
1 Source supports size with size sensing.
2 Source supports size without size sensing.
3 Paper size is supported if set to metric.
4 Paper size is supported if set to US.
5 Paper size is supported if loaded in the short‑edge orientation. The short edge of the paper enters the printer first.
6 Paper size is supported if loaded in the long‑edge orientation. The long edge of the paper enters the printer first.
7 This is applicable only to the optional 520‑sheet tray.

Paper and specialty media guide 75

86 x 165 mm to 216 x 356 mm (3.375 x 6.50 in. to 8.5 x 14 in.)
3 Paper size is supported if set to metric.
4 Paper size is supported if set to US.
5 Paper size is supported if loaded in the short‑edge orientation. The short edge of the paper enters the printer first.
6 Paper size is supported if loaded in the long‑edge orientation. The long edge of the paper enters the printer first.
7 This is applicable only to the optional 520‑sheet tray.
The printer supports 60–300 g/m2 (16–80 lb) paper weights. The duplex unit supports 60–169 g/m2 (16–32 lb) paper weights.


Paper and specialty media guide 76

The paper capacity of each exit bin is listed in parentheses. Paper capacity estimations are calculated based on 75 g/m2 (20 lb) paper.
The finisher standard bin supports 60–300 g/m2 (16–80 lb) paper weights, bin 1 supports 60–220 g/m2 (16– 60 lb) paper weights, and bin 2 (booklet‑maker) supports 60–90 g/m2 (16–24 lb) paper weights plus one additional cover weighted up to 220 g/m2 (60 lb).

Paper type Standard 500‑sheet bin Second exit bin Bin 1 Bin 2 Bin 3

Paper and specialty media guide 77


Paper and specialty media guide 78

Size Punch* Offset Single/Double staple Double dual staple
* For the Universal paper size, the finishing edge must be at least 9 in. (229 mm) for a 3‑hole punch and 10 in. (254 mm) for a 4‑hole punch.
Punch—Select from two‑, three‑, or four‑hole punch
Double staple—Use two staples Double dual staple—Use two sets of two staples. This setting is supported only for widths between 8 in. (203 mm) and 12 in. (297 mm) with lengths between 7 in. (182 mm) and 17 in. (432 mm).
Bin 2 (booklet‑maker)
Bin 2 is available only when the booklet finisher is installed. The paper capacity of bin 2 (booklet‑maker) is 270 sheets or 18 sets of 15‑sheet booklets.

SEF—The paper is loaded in the short edge orientation. The short edge of the paper enters the printer first.
Bi fold—Each page is individually folded and stacked separately.
Booklet fold—A multiple-page job is folded along the center into a single booklet. Saddle staple—A booklet‑fold print job is stapled along the center fold.

Paper and specialty media guide 79

SEF—The paper is loaded in the short edge orientation. The short edge of the paper enters the printer first.
Bi fold—Each page is individually folded and stacked separately. Booklet fold—A multiple-page job is folded along the center into a single booklet.
Saddle staple—A booklet‑fold print job is stapled along the center fold.
1 From the home screen, navigate to:
> Paper Menu > Bin setup > Output bin
2 Select a bin, and then touch

The selection and handling of paper and specialty media can affect how reliably documents print. For more information, see “Avoiding jams” on page 179 and “Storing paper” on page 72.
1 From the printer control panel Paper menu, set the Paper Type and Paper Size to match the loaded paper.
2 Send the print job:
a With a document open, click File > Print. b Click Properties, Preferences, Options, or Setup.
c Adjust settings as necessary. d Click OK > Print.
a Customize the settings as needed in the Page Setup dialog:
1 With a document open, choose File > Page Setup. 2 Choose a paper size or create a custom size to match the loaded paper. 3 Click OK. b Customize the settings as needed in the Print dialog:
1 With a document open, choose File > Print. If necessary, click the disclosure triangle to see more options. 2 From the Print dialog and pop‑up menus, adjust the settings as needed.
From the home screen, navigate to:
> Settings > Print Settings > Quality Menu > Print Mode > Black Only >
1 Type the printer IP address into the address field of your Web browser.
Printing 80

If you do not know the IP address of the printer, you can:
2 Click Settings > Print Settings > Quality Menu > Toner Darkness.
3 Adjust the toner darkness setting.
4 Click Submit.
The Max Speed and Max Yield settings let you choose between a faster print speed or a higher toner yield. Max Yield is the factory default setting.
1 Type the printer IP address or host name in the address field of your Web browser.
If you do not know the IP address or host name of the printer, then you can:
2 Click Configuration > Print Settings > Setup Menu.
3 From the Printer Usage list, select Max Speed or Max Yield.
4 Click Submit.
1 From the home screen, navigate to:
> Settings > Print Settings > Setup Menu
2 From the Printer Usage list, select Max Speed or Max Yield.
For the list of supported mobile devices and to download a compatible mobile printing application, visit http://lexmark.com/mobile.
Printing 81 · 3 Touch

1 Insert a flash drive into the USB port.

Printing 82


2 From the printer control panel, touch the document you want to print.
3 Touch the arrows to increase the number of copies to print, and then touch Print.

Printing 83

Source Print side Paper orientation
Standard and optional trays (simplex printing) Preprinted letterhead design is placed faceup.
When feeding short edge, the top edge of the sheet with the logo is placed at the right side of the tray. When feeding long‑edge, the letter head should go to the rear of the printer.
Standard and optional trays (duplex printing) Preprinted letterhead design is placed facedown.
The top edge of the sheet with the logo is placed at the right side of the tray.
Multipurpose feeder (simplex printing) Preprinted letterhead design is placed facedown.
The top edge of the sheet with the logo should enter the multipurpose feeder first.
Multipurpose feeder (duplex printing) Preprinted letterhead design is placed faceup.
The top edge of the sheet with the logo should enter the multipurpose feeder last.
Printing 84

Print samples on the envelopes being considered for use before buying large quantities.
For detailed information on label printing, characteristics, and design, see the Card Stock & Label Guide available on the Lexmark Web site at http://support.lexmark.com.
When printing on labels:
or releasing hazardous emissions.
without delaminating, oozing around the edges, or releasing hazardous fumes. • Do not use labels with slick backing material.
Printing 85

Card stock is heavy, single‑ply specialty media. Many of its variable characteristics, such as moisture content, thickness, and texture, can significantly impact print quality. Print samples on the card stock being considered for use before buying large quantities.
You can set the printer to store print jobs in the printer memory until you start the print job from the printer control panel.
All print jobs that can be initiated by the user at the printer are called held jobs.
Printing 86

Print job type Description
Confidential Confidential lets you hold print jobs in the computer until you enter the PIN from the control panel.
Verify Verify lets you print one copy of a print job while the printer holds the remaining copies. It allows you to examine if the first copy is satisfactory. The print job is automatically deleted from the printer memory once all copies are printed.
Reserve Reserve allows the printer to store print jobs for printing at a later time. The print jobs are held until deleted from the Help Jobs menu.
Repeat Repeat prints and stores print jobs in the printer memory for reprinting.
1 With a document open, click File > Print.
2 Click Properties, Preferences, Options, or Setup.
3 Click Print and Hold.
4 Select the print job type (Confidential, Repeat, Reserve, or Verify), and then assign a user name. For a confidential print job, also enter a four‑digit PIN.
5 Click OK or Print.
1 With a document open, choose File > Print.
If necessary, click the disclosure triangle to see more options.
2 From the print options or Copies & Pages pop‑up menu, choose Job Routing.
3 Select the print job type (Confidential, Repeat, Reserve, or Verify), and then assign a user name. For a confidential print job, also enter a four‑digit PIN.
4 Click OK or Print.
Printing 87

1 From the home screen, navigate to:
> Reports > Print Fonts
2 Touch PCL Fonts or PostScript Fonts.
A directory list shows the resources stored in a flash memory or on the printer hard disk.
From the home screen, navigate to:
> Reports > Print Directory
1 From the printer control panel, touch Cancel Job or press
on the keypad.
2 Touch the print job you want to cancel, and then touch Delete Selected Jobs.
on the keypad, then touch Resume to return to the home screen.
1 Open the printers folder.
From the Search charm, type run, and then navigate to:
Apps list > Run > type control printers > OK
Printing 88 · In Windows 8

In Windows 7 or earlier
or click Start, and then click Run. b In the Start Search or Run dialog, type control printers.
c Press Enter, or click OK.
2 Double‑click the printer icon.
3 Select the print job you want to cancel.
4 Click Delete.
2 From the printer window, select the print job you want to cancel, and then delete it.
Printing 89 · a Click

Understanding the printer menus 90
Menus list
Supplies Menu Paper Menu Reports Settings
Yellow Cartridge Black Cartridge
Configure MP Substitute Size
Network Setup Page Network [x] Setup Page
Black Photoconductor Unit Waste Toner Bottle
Custom Names Custom Bin Names
Print Demo Asset Report
Hole Punch Box 160K Maintenance Kit
Standard Network or Network [x]2
Color Quality Print Quality
Erase Temporary Data Files1
Standard USB Parallel [x]
Set Date and Time
Media Guide Print Defects Guide
Moving Guide Supplies Guide
1 This menu appears only when a printer hard disk is installed.
2 Depending on the printer setup, this menu appears as Standard Network, Wireless Network, or Network [x].

Understanding the printer menus 91
Shows the status of the cyan print cartridge
Early Warning Low Invalid Replace Missing or Defective OK Unsupported
Shows the status of the magenta print cartridge
Early Warning Low Invalid Replace Missing or Defective OK Unsupported
Shows the status of the yellow print cartridge
Early Warning Low Invalid Replace Missing or Defective OK Unsupported
Shows the status of the black print cartridge
Early Warning Low Invalid Replace Missing or Defective OK Unsupported
Shows the status of the cyan photoconductor unit
Early Warning Low Replace Missing OK

Understanding the printer menus 92
Shows the status of the magenta photoconductor unit
Early Warning Low Replace Missing OK
Shows the status of the yellow photoconductor unit
Early Warning Low Replace Missing OK
Shows the status of the black photoconductor unit
Early Warning Low Replace Missing OK
Shows the status of the waste toner bottle
Near Full Replace Missing OK
Shows the status of the staple cartridge
Early Warning Low Replace Missing OK
Shows the status of the hole punch box
Near Full Replace Missing OK
160K Maintenance Kit Near End of Life End of Life OK
Shows the status of the maintenance kit
320K Maintenance Kit Near End of Life End of Life OK
Shows the status of the maintenance kit

Understanding the printer menus 93
480K Maintenance Kit Near End of Life End of Life OK
Shows the status of the maintenance kit
Sets a default paper source for all print jobs
Tray [x] MP Feeder Manual Paper Manual Envelope
Specifies the paper size loaded in each tray
Letter Legal Executive JIS‑B4 A3 11 x 17 Oficio (México) Folio Statement Universal A4 A5 A6 JIS B5

Understanding the printer menus 94
Specifies the paper type loaded in each tray
Plain Paper Card Stock Transparency Recycled Glossy Heavy Glossy Labels Bond Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Paper Custom Type [x]
Specifies the paper size loaded in the multipurpose feeder
Letter Legal Executive JIS‑B4 A3 11 x 17 12 x 18 Oficio (México) Folio Statement Universal 7 3/4 Envelope 10 Envelope DL Envelope C5 Envelope Other Envelope A4 A5 A6 JIS B5 SRA3
Menu item Description · Tray [x] Type · MP Feeder Size

Understanding the printer menus 95
Specifies the paper type loaded in the multipurpose feeder
Custom Type [x] Plain Paper Card Stock Transparency Recycled Glossy Heavy Glossy Labels Bond Envelope Rough Envelope Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Paper
Specifies the paper size being manually loaded
Letter Legal Executive JIS‑B4 A3 11 x 17 12 x 18 Oficio (México) Folio Statement Universal A4 A5 A6 JIS B5 SRA3
Menu item Description · MP Feeder Type · Manual Paper Size

Understanding the printer menus 96
Specifies the paper type being manually loaded
Plain Paper Card Stock Transparency Recycled Glossy Heavy Glossy Labels Bond Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Paper Custom Type [x]
Specifies the envelope size being manually loaded
10 Envelope DL Envelope C5 Envelope Other Envelope 7 3/4 Envelope
Specifies the envelope type being manually loaded
Envelope Rough Envelope Custom Type [x]
Determines when the printer selects paper from the multipurpose feeder

Understanding the printer menus 97
Substitutes a specified paper size if the requested paper size is not available
All Listed Off Statement/A5 Letter/A4 11 x 17/A3
Specifies the relative texture of the paper loaded
Specifies the relative texture of the card stock loaded
Specifies the relative texture of the transparencies loaded
Specifies the relative texture of the recycled paper loaded
Specifies the relative texture of the glossy paper loaded
Specifies the relative texture of the glossy paper loaded

Understanding the printer menus 98
Specifies the relative texture of the labels loaded
Specifies the relative texture of the bond paper loaded
Specifies the relative texture of the envelopes loaded
Specifies the relative texture of the envelopes loaded
Specifies the relative texture of the letterhead loaded
Specifies the relative texture of the preprinted paper loaded
Specifies the relative texture of the colored paper loaded
Specifies the relative texture of the paper loaded
Specifies the relative texture of the paper loaded
Specifies the relative texture of the cotton paper loaded
Specifies the relative texture of the custom paper loaded

Understanding the printer menus 99
Determine and set two-sided printing for all print jobs with Card Stock as the paper type.
Determine and set two-sided printing for all print jobs with Recycled as the paper type.
Determine and set two-sided printing for all print jobs with Glossy as the paper type.
Determine and set two-sided printing for all print jobs with Heavy Glossy as the paper type.
Determine and set two-sided printing for all print jobs with Bond as the paper type.
Determine and set two-sided printing for all print jobs with Letterhead as the paper type.
Determine and set two-sided printing for all print jobs with Preprinted as the paper type.
Determine and set two-sided printing for all print jobs with Colored as the paper type.
Determine and set two-sided printing for all print jobs with Light as the paper type.
Determine and set two-sided printing for all print jobs with Heavy as the paper type.
Determine and set two-sided printing for all print jobs with Rough or Cotton as the paper type.

Understanding the printer menus 100
Determine and set two-sided printing for all print jobs with Custom [x] as the paper type.
Associate a paper or specialty media type with a Custom Type [x] name.
Paper Card Stock Transparency Glossy Rough/Cotton Labels Bond Envelope
Specify a paper type when the Recycled setting is selected in other menus.
Paper Card Stock Transparency Glossy Rough/Cotton Labels Envelope
Specify a custom name for a paper type. This name replaces the Custom Type [x] name in the printer menus.
Standard Bin Specifies a custom name for the Standard Bin
Bin [x] Specifies a custom name for Bin [x]

Understanding the printer menus 101
Specify the unit of measure.
Set the portrait width.
3–48 inches 76–1219 mm
Set the portrait height
3–48 inches 76–1219 mm
Specifies the default output bin
Standard Bin Bin [x]
Specifies configuration options for output bins
Mailbox Link Type Assignment

Understanding the printer menus 102
Selects an output bin for each supported paper type
Plain Paper Bin Card Stock Bin Transparency Bin Recycled Bin Glossy Bin Heavy Glossy Bin Labels Bin Bond Bin Envelope Bin Rough Envelope Bin Letterhead Bin Preprinted Bin Colored Bin Light Paper Bin Heavy Paper Bin Rough/Cotton Bin Custom [x] Bin
Available selections for each type are:
Disabled Standard Bin Bin [x]
Menu Settings Page Print a report on the current printer settings.
Device Statistics Print a report containing printer statistics.
Network Setup Page Print a report on the network printer settings.
Profiles List Print a list of profiles stored in the printer.
Print a report of all the fonts available for the printer language currently set in the printer.
PCL Fonts PostScript Fonts
Print Directory Print a list of all the resources stored in an optional flash memory card.
Asset Report Print a report on printer asset information.
![Page 103 of the Lexmark C 950 user manual — Standard Network or Network [x] menus](/cdn/reader/c5/c5447e89ce310907a4495e702c5ae8eed252c4319418f7ecb3ef346aa39ca00a/images/page-103.webp?w=400)
Understanding the printer menus 103
Print demo files that are available in the firmware, the flash option, and the disk option.
Auto [list of available network cards]
Sets the printer to automatically switch to PCL emulation when a print job requires it, regardless of the default printer language
Sets the printer to automatically switch to PS emulation when a print job requires it, regardless of the default printer language
Sets the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol

Understanding the printer menus 104
Sets the size of the network input buffer
Auto 3KB to [maximum size allowed]
Temporarily stores print jobs on the printer hard disk before printing. This menu only appears if a formatted disk is installed.
Sets the printer to process Macintosh binary PostScript print jobs
Displays and sets the printer network settings.
Reports Network Card TCP/IP IPv6 Wireless AppleTalk
Reports Network Card TCP/IP IPv6 Wireless AppleTalk

Understanding the printer menus 105
This menu is available from the Network/Ports menu:
Network/Ports > Standard Network or Network [x] > Standard Network Setup or Network [x] Setup > Reports or Network Reports
Print Setup Page Prints a report containing information about the network printer settings, such as the TCP/IP
This menu is available from the Network/Ports menu:
Network/Ports > Standard Network or Network [x] > Standard Network Setup or Network [x] Setup > Network Card
Lets you view the connection status of the Network Card
View Card Speed Lets you view the speed of a currently active network card
Lets you view the network addresses
End‑of‑Job Timeout
Sets the amount of time in seconds before a network print job is canceled
Allows the printer to print a banner page
Set Hostname Lets you set the current TCP/IP host name

Understanding the printer menus 106
IP Address Lets you view or change the current TCP/IP address
Netmask Lets you view or change the current TCP/IP netmask
Gateway Lets you view or change the current TCP/IP gateway
Specifies the DHCP address and parameter assignment setting
Specifies the RARP address assignment setting
Specifies the BOOTP address assignment setting
Specifies the Zero Configuration Networking setting
Enables the built-in FTP server, which allows you to send files to the printer using File Transfer Protocol.
Enables the built-in Web server (Embedded Web Server). When enabled, the printer can be monitored and managed remotely using a Web browser.
WINS Server Address Lets you view or change the current WINS server address
DNS Server Address Lets you view or change the current DNS server address
Backup DNS Server Address View or change the backup DNS server addresses.
Backup DNS Server Address 2
Backup DNS Server Address 3
This menu is available from the Network/Ports menu:
Network/Ports > Standard Network or Network [x] > Standard Network Setup or Network [x] Setup > IPv6
Enables IPv6 in the printer

Understanding the printer menus 107
Specifies whether the network adapter accepts the automatic IPv6 address configuration entries provided by a router
Set Hostname Lets you set the printer host name
View Address Shows the printer IPv6 address
View Router Address Shows the router address
Enables DHCPv6 in the printer
Use the following menu items to view or configure the wireless internal print server settings.
The Wireless menu is available from the Network/Ports menu:
Network/Ports > Standard Network or Network [x] > Standard Network Setup or Network [x] Setup > Wireless
Lets you connect the printer to a wireless network by pressing buttons on both the printer and the access point (wireless router) within a given period of time
Lets you connect the printer to a wireless network by using a PIN on the printer and entering it into the wireless settings of the access point
Automatically detects the connection method that an access point with WPS uses—WPS Push Button Configuration (PBC) or WPS Personal Identification Number (PIN)
Specifies the network mode

Understanding the printer menus 108
Specifies the wireless standard for the wireless network
802.11b/g 802.11b/g/n
Lets you select an available network for the printer to use
[list of available networks]
View Signal Quality Lets you view the quality of the wireless connection
View Security Mode Lets you view the encryption method that a wireless network uses
To access the menu, navigate to either of the following:
Enable or disable AppleTalk support.
View Name Show the assigned AppleTalk name.
View Address Show the assigned AppleTalk address.
Provide a list of AppleTalk zones available on the network.
[list of zones available on the network]

Understanding the printer menus 109
Sets the printer to automatically switch to PCL emulation when a print job received through a USB port requires it, regardless of the default printer language
Sets the printer to automatically switch to PS emulation when a print job received through a USB port requires it, regardless of the default printer language
Sets the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol
Sets the size of the USB input buffer
Auto 3KB to [maximum size allowed] Disabled
![Page 110 of the Lexmark C 950 user manual — Parallel [x] menu](/cdn/reader/c5/c5447e89ce310907a4495e702c5ae8eed252c4319418f7ecb3ef346aa39ca00a/images/page-110.webp?w=400)
Understanding the printer menus 110
Temporarily stores print jobs on the printer hard disk before printing
Sets the printer to process Macintosh binary PostScript print jobs
Sets the network address information for an external print server
yyy.yyy.yyy.yyy
Sets the netmask information for an external print server
yyy.yyy.yyy.yyy
Sets the gateway information for an external print server
yyy.yyy.yyy.yyy
Sets the printer to automatically switch to PCL emulation when a print job received through a serial port requires it, regardless of the default printer language
![Page 111 of the Lexmark C 950 user manual — Parallel [x] menu](/cdn/reader/c5/c5447e89ce310907a4495e702c5ae8eed252c4319418f7ecb3ef346aa39ca00a/images/page-111.webp?w=400)
Understanding the printer menus 111
Sets the printer to automatically switch to PS emulation when a print job received through a serial port requires it, regardless of the default printer language
Sets the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol
Sets the size of the parallel input buffer
Auto 3KB to [maximum size allowed] Disabled
Temporarily stores print jobs on the printer hard disk before printing
Enables bidirectional communication through the parallel port
![Page 112 of the Lexmark C 950 user manual — Parallel [x] menu](/cdn/reader/c5/c5447e89ce310907a4495e702c5ae8eed252c4319418f7ecb3ef346aa39ca00a/images/page-112.webp?w=400)
Understanding the printer menus 112
Specifies the parallel port protocol
Determines if the printer honors printer hardware initialization requests from the computer
Determines if the parallel port data is sampled on the leading or trailing edge of a strobe
Sets the printer to process Macintosh binary PostScript print jobs
Sets the network address information for an external print server
yyy.yyy.yyy.yyy
Sets the netmask information for an external print server
yyy.yyy.yyy.yyy
Sets the gateway information for an external print server
yyy.yyy.yyy.yyy
![Page 113 of the Lexmark C 950 user manual — Serial [x] menu](/cdn/reader/c5/c5447e89ce310907a4495e702c5ae8eed252c4319418f7ecb3ef346aa39ca00a/images/page-113.webp?w=400)
Understanding the printer menus 113
Sets the printer to automatically switch to PCL emulation when a print job received through a serial port requires it, regardless of the default printer language
Sets the printer to automatically switch to PS emulation when a print job received through a serial port requires it, regardless of the default printer language
Sets the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol
Sets the size of the serial input buffer
Auto 3KB to [maximum size allowed] Disabled

Understanding the printer menus 114
Temporarily stores print jobs on the printer hard disk before printing
Selects the hardware and software handshaking settings for the serial port
Determines whether the printer communicates availability to the computer
Specifies the rate at which data can be received through the serial port
9600 19200 38400 57600 115200 138200 172800 230400 345600 1200 2400 4800
Specifies the number of data bits sent in each transmission frame
Sets the parity for serial input and output data frames
None Ignore Even Odd

Understanding the printer menus 115
Determines whether the printer uses the DSR Signal
Primary SMTP Gateway Specifies SMTP server gateway and port information
Secondary SMTP Gateway Port
5–30 Specifies the amount of time in seconds before the server stops trying to send an e‑mail
Reply Address Specifies a reply address of up to 128 characters in the e-mail sent by the printer
Sets the printer to use SSL for increased security when connecting to the SMTP server
Specifies the type of user authentication required for scan to e‑mail privileges
No authentication required Login/Plain CRAM‑MD5 Digest‑MD5 NTLM Kerberos 5

Understanding the printer menus 116
Device‑Initiated E‑mail
Specifies what credentials will be used when communicating to the SMTP server. Some SMTP servers require credentials to send an e- mail.
None Use Device SMTP Credentials
User‑Initiated E‑mail
None Use Device SMTP Credentials Use Session User ID & Password Use Session E‑mail address & Password Prompt User
Limit the number and time frames of failed login attempts from the printer control panel before all users are locked out.
Login failures Failure time frame Lockout time Panel Login Timeout Remote Login Timeout

Understanding the printer menus 117
Adjust the security settings.
Access controls=”No Security” No Effect Reset factory security defaults
Allow the user to request a server certificate.
Demand Try Allow Never
1–16 Limit the digit length of the personal identification number (PIN).
Limits the number of times an invalid PIN can be entered
Limits the amount of time a confidential print job stays in the printer before it is deleted
Off 1 hour 4 hours 24 hours 1 week

Understanding the printer menus 118
Sets a time limit on how long the printer stores print jobs
Off 1 hour 4 hours 24 hours 1 week
Sets a time limit on how long the printer stores print jobs needing verification
Off 1 hour 4 hours 24 hours 1 week
Sets a time limit on how long the printer stores print jobs for printing at a later time
Off 1 hour 4 hours 24 hours 1 week
Erase Temporary Data Files deletes only print job data on the printer hard disk that are not currently in use by the file system. All permanent data on the hard disk are preserved, such as downloaded fonts, macros, and held jobs.
Specify the mode for erasing temporary data files.
Specify a method for automatic disk wiping.
Single pass Multi‑pass
Specify a method for manual disk wiping.
Single pass Multi‑pass

Understanding the printer menus 119
Specify a method for a scheduled disk wiping.
Single pass Multi‑pass
Export Log Enables an authorized user to export the audit log
Specifies whether audit logs are deleted
Specifies whether and how audit logs are created
No Yes Enable Remote Syslog
No Yes Remote Syslog Facility
0–23 Severity of events to log
Current Date and Time Shows the current date and time settings for the printer
Manually Set Date and Time
[list of time zones]

Understanding the printer menus 120
Enables Network Time Protocol, which synchronizes the clocks of devices on a network
Set the language of the text appearing on the display.
English Francais Deutsch Italiano Espanol Dansk Norsk Nederlands Svenska Portugues Suomi Russian Polski Greek Magyar Turkce Cesky Simplified Chinese Traditional Chinese Korean Japanese
Minimize the use of energy, paper, or specialty media.
Off Energy Energy/Paper Paper

Understanding the printer menus 121
Minimize the printer noise.
Run the setup wizard.
Specify a language and custom key information for the display keyboard.
English Francais Francais Canadien Deutsch Italiano Espanol Greek Dansk Norsk Nederlands Svenska Suomi Portugues Russian Polski Swiss German Swiss French Korean Magyar Turkish Czech Simplified Chinese Traditional Chinese Japanese Custom Key [x]
Specify the unit of measurement for paper sizes.
U.S. Metric

Understanding the printer menus 122
Specify what is displayed on the upper corners of the home screen.
Left side Right side Custom Text [x]
For Left side and Right side, select from the following options:
None IP Address Hostname Contact Name Location Date/Time mDNS/DDNS Service Name Zero Configuration Name Custom Text [x] Model Name
Customize the displayed information for the parts and supplies. Select from the following options:
[x] Toner [x] Photoconductor Waste Toner Bottle Fuser Transfer Module
Do not display Display Message to display

Understanding the printer menus 123
Customize the displayed information for certain menus.
Paper Jam Load Paper Service Errors
Select from the following options:
Do not display Alternate Message to display
Change the icons that appear on the home screen.
Change Language Search Held Jobs Held Jobs USB Drive Profiles Bookmarks Jobs by User
For each icon, select from the following options:
Display Do not display
Format the date.
MM‑DD‑YYYY DD‑MM‑YYYY YYYY‑MM‑DD
Format the time.
12 hour A.M./P.M. 24 hour clock
20–100 Specify the brightness of the display.
Set the output lighting for the standard bin.
Custom Background Image Import a background image.

Understanding the printer menus 124
Specify the audio volume for the buttons.
Enable touch‑screen sensation feedback.
Web Page Refresh Rate
30–300 Specify the number of seconds between Embedded Web Server refreshes.
Contact Name Specify a contact name.
Location Specify the location.
Set an alarm when the printer requires user intervention.
Alarm Control Cartridge Alarm Stapler Alarm Hole Punch Alarm
For each alarm type, select from the following options:
Set the amount of time before the printer enters a lower power state.
Set the amount of time in minutes the printer waits after a job is printed before it goes into a reduced power state.

Understanding the printer menus 125
Set the amount of time the printer waits before it enters Hibernate mode.
Disabled 20 minutes 1–3 hours 6 hours 1–3 days 1–2 weeks 1 month
Hibernate Timeout on Connection
Set the printer to Hibernate mode even if there is an active Ethernet connection.
Hibernate Do Not Hibernate
Set the amount of time in seconds before returning the control panel to a Ready state.
Set the amount of time in seconds the printer waits to receive an end-of-job message before canceling the rest of the job.
Set the amount of time in seconds the printer waits for more data before canceling a print job.
Set the amount of time in seconds the printer waits for user intervention before it holds jobs that require unavailable resources and continues to print other jobs in the print queue.

Understanding the printer menus 126
Let the printer automatically continue printing from certain offline situations when these are not resolved within the specified time period.
Specify whether the printer reprints jammed pages.
Successfully print a page that may not have printed otherwise.
Determine how the printer, while in idle state, reacts to a short press of the Sleep button.
Do Nothing Sleep Hibernate
Press and Hold Sleep Button
Determine how the printer, while in idle state, reacts to a long press of the Sleep button.
Use the printer factory default settings except the Network/Ports menu settings.
Do Not Restore Restore Now

Understanding the printer menus 127
Specifies whether duplex (2‑sided) printing is set as the default setting for all print jobs
1 sided 2 sided
Defines the way duplexed pages are bound and how the printing on the back of the page is oriented in relation to the printing on the front of the page
Long Edge Short Edge
1–999 Specifies the default number of copies for each print job
Specifies whether blank pages are inserted in a print job
Do Not Print Print
Stacks the pages of a print job in sequence when printing multiple copies
Off (1,1,1,2,2,2) On (1,2,1,2,1,2)
Specifies whether blank separator sheets are inserted
Off Between Copies Between Jobs Between Pages

Understanding the printer menus 128
Specifies the paper source for separator sheets
Tray [x] Manual Feeder
Specifies that multiple‑page images be printed on one side of a paper
Off 2‑Up 3‑Up 4‑Up 6‑Up 9‑Up 12‑Up 16‑Up
Specifies the positioning of multiple‑page images when using Paper Saver
Horizontal Reverse Horizontal Reverse Vertical Vertical
Specifies the orientation of a multiple‑page document
Prints a border on each page image when using Paper Saver
Specifies whether the prints are stapled
Off Auto Back Dual Dual Double Front
Specifies whether the prints have punched holes
Determines the type of punch finishing performed on a printed output
2 holes 3 holes 4 holes

Understanding the printer menus 129
Offsets pages at certain instances
None Between Copies Between Jobs
Specify whether to print images in color.
Adjust the color output on the printed page.
Specify the output resolution in dots per inch (dpi) or in image quality.
1200 dpi 2400 Image Q
1–5 Lighten or darken the output.
Enable a print mode preferable for files such as architectural drawings, maps, electrical circuit diagrams, and flow charts.
Reduce the amount of toner used for graphics and images.
Adjust the brightness of the output.
‑6 to 6
0–5 Adjust the contrast of the output.
0–5 Adjust saturation in color outputs.

Understanding the printer menus 130
Enable an equal balance of colors in the output.
‑5 to 5 Magenta
‑5 to 5 Yellow
‑5 to 5 Black
‑5 to 5 Reset Defaults
Print sample pages for each of the RGB and CMYK color conversion tables used in the printer.
sRGB Display sRGB Vivid Display—True Black Vivid Off—RGB US CMYK Euro CMYK Vivid CMYK Off—CMYK
Customize the RGB color conversions.
RGB Image RGB Text RGB Graphics
Select from the following options:
Vivid sRGB Display Display—True Black sRGB Vivid Off
Customize the CMYK color conversions.
CMYK Image CMYK Text CMYK Graphics
Select from the following options:
US CMYK Euro CMYK Vivid CMYK Off
Spot Color Replacement Assign specific CMYK values to named spot colors.
RGB Replacement Match the colors of the output with that of the original document.

Understanding the printer menus 131
Determines if the printer creates a log of the print jobs it receives
Job Accounting Utilities Lets you print and delete log files or export them to a flash drive
Determines how often a log file is created
Log Action at End of Frequency
Determines how the printer responds when the frequency threshold expires
None E‑mail Current Log E‑mail & Delete Current Log Post Current Log Post & Delete Current Log
Disk Near Full Level
Specifies the maximum size of the log file before the printer executes the Disk Near Full Action
Disk Near Full Action
Determines how the printer responds when the printer hard disk is nearly full
None E‑mail Current Log E‑mail & Delete Current Log E‑mail & Delete Oldest Log Post Current Log Post & Delete Current Log Post & Delete Oldest Log Delete Current Log Delete Oldest Log Delete All Logs Delete All But Current
Determines how the printer responds when disk usage reaches the maximum limit (100MB)
None E‑mail & Delete Current Log E‑mail & Delete Oldest Log Post & Delete Current Log Post & Delete Oldest Log Delete Current Log Delete Oldest Log Delete All Logs Delete All But Current
URL to Post Logs Determines where the printer posts job accounting logs

Understanding the printer menus 132
E‑mail Address to Send Logs Specifies the e‑mail address to which the device sends job accounting logs
Log File Prefix Note: The current host name defined in the TCP/IP menu is used as the default log file prefix.
Sets the default printer language
PS Emulation PCL Emulation
Specifies if print jobs are removed from the print queue when they require unavailable printer options or custom settings. These print jobs are stored in a separate print queue, so other jobs print normally. When the missing information and/or options are obtained, the stored jobs print.
Sets the logical and physical printable area
Sets the printer for a faster print speed or a higher toner yield.
Max Yield Max Speed

Understanding the printer menus 133
Sets the printer to print text and graphics using only the black toner cartridge
Sets the storage location for downloads
Specifies how the printer handles temporary downloads, such as fonts and macros stored in the RAM, when the printer receives a print job that requires more memory than is available
Specifies the order in which held and confidential jobs are printed when Print All is selected
Alphabetical Oldest First Newest First
Prints a page containing the PostScript error
Lock PS Startup Mode
Enables users to disable the SysStart file

Understanding the printer menus 134
Establishes the font search order
Enhances the contrast and sharpness of low‑resolution images and smooths their color transitions
Specifies the set of fonts used by the Font Name menu item
Resident Disk Download Flash All
Identifies a specific font and where it is stored
Specifies the symbol set for each font name

Understanding the printer menus 135
Changes the point size for scalable typographic fonts
1.00–1008.00
Specifies the font pitch for scalable monospaced fonts
0.08–100
Specifies the orientation of text and graphics on a page
Specifies the number of lines that print on each page
Sets the printer to print on A4‑size paper
198 mm 203 mm
Specifies whether the printer automatically performs a carriage return (CR) after a line feed (LF) control command
Auto CR after LF
Specifies whether the printer automatically performs a line feed (LF) after a carriage return (CR) control command
Auto LF after CR

Understanding the printer menus 136
Configures the printer to work with printer software or programs that use different source assignments for trays, drawers, and feeders
Off None 0–199 Assign Tray [x]
Off None 0–199 Assign Manual Paper
Off None 0–199 Assign Manual Env
Displays the factory default setting assigned to each tray, drawer, or feeder
MPF Default = 8 T1 Default = 1 T2 Default = 4 T3 Default = 5 T4 Default = 20 T5 Default = 21 Env Default = 6 MPaper Default = 2 MEnv Default = 3
Returns all tray, drawer, and feeder assignments to the factory default settings
Prints a page containing information on errors, including XML markup errors

Understanding the printer menus 137
Scales page content to fit the selected paper size
Prints annotations in a PDF
Do Not Print Print
Joanna MT Letter Gothic Lubalin Graph Marigold MonaLisa Recut Monaco New CenturySbk New York Optima Oxford Palatino StempelGaramond Taffy Times TimesNewRoman Univers Zapf Chancery NewSansMTCS NewSansMTCT New SansMTJA NewSansMTKO
Sets the default font for HTML documents
Albertus MT Antique Olive Apple Chancery Arial MT Avant Garde Bodoni Bookman Chicago Clarendon Cooper Black Copperplate Coronet Courier Eurostile Garamond Geneva Gill Sans Goudy Helvetica Hoefler Text Intl CG Times Intl Courier Intl Univers
1–255 pt Sets the default font size for HTML documents

Understanding the printer menus 138
1–400% Scales the default font for HTML documents
Sets the page orientation for HTML documents
8–255 mm Sets the page margin for HTML documents
Specifies whether to print backgrounds on HTML documents
Print Do Not Print
Selects the optimal paper size, scaling, and orientation
Inverts bi‑tonal monochrome images
Scales the image to fit the selected paper size
Best Fit Anchor Center Fit Height/Width Fit Height Fit Width Anchor Top Left
Sets the image orientation
Portrait Landscape Rev Portrait Rev Landscape

Understanding the printer menus 139
1–999 Specify a default number of copies for each print job.
Set a default paper source for all print jobs.
Tray [x] Manual Paper Manual Envelope
Specify whether to print the document in color.
Stack the pages of a print job in sequence when printing multiple copies.
Off (1,1,12,2,2) On (1,2,1,2,1,2)
Enable two‑sided printing for incoming print jobs.
1 sided 2 sided
Define binding for two-sided pages in relation to paper orientation.
Long Edge Short Edge
Specify the orientation of a multiple‑page document.
Print multiple‑page images on one side of the paper.
Off 2‑Up 3‑Up 4‑Up 6‑Up 9‑Up 12‑Up 16‑Up
Print a border on each page image.

Understanding the printer menus 140
Specify the positioning of multiple‑page images.
Horizontal Reverse Horizontal Reverse Vertical Vertical
Specify whether to insert blank separator sheets.
Off Between Copies Between Jobs Between Pages
Specify the paper source for separator sheets.
Specify whether to insert blank pages in a print job.
Do Not Print Print
Print All Guides Prints all the guides
Color Quality Provides information about solving color quality issues
Print Quality Provides information about solving print quality issues
Printing Guide Provides information about loading paper and other specialty media
Media Guide Provides a list of the paper sizes supported in trays and feeders
Print Defects Guide Provides a template for determining the cause of repeating print quality defects, and lists settings that can be used to adjust print quality
Menu Map Provides a list of the control panel menus and settings
Information Guide Provides help in locating additional information
Connection Guide Provides information about connecting the printer locally (USB) or to a network
Moving Guide Provides instructions for safely moving the printer
Supplies Guide Provides information about ordering supplies

Securing the hard disk and other installed memory 141
Statement of Volatility
Your printer contains various types of memory that are capable of storing device and network settings, information from embedded solutions, and user data. The types of memory—along with the types of data stored by each—are described below.
There are several circumstances under which you might wish to erase the contents of the memory devices installed in your printer. A partial list includes:
In high‑security environments, it may be necessary to take additional steps to ensure that confidential data stored on the printer hard disk cannot be accessed once the printer—or its hard disk—is removed from your premises. While most data can be erased electronically, you may want to consider one or more of the following actions before disposing of a printer or hard disk:

Securing the hard disk and other installed memory 142
The volatile memory (RAM) installed on your printer requires a power source to retain information. To erase the buffered data, simply power down the device.
1 Turn off the printer.
2 Hold down and 6 MNO while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully powered up, the touch screen displays a list of functions, instead of the standard home screen icons.
3 Touch Wipe All Settings.
The printer will reboot several times during this process.
4 Touch Back > Exit Config Menu.
The printer will power‑on reset, and then return to normal operating mode.
1 Turn off the printer.
2 Hold down 2 and 6 while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully turned on, the touch screen displays a list of functions.
4 Touch Yes to proceed with disk wiping.

Securing the hard disk and other installed memory 143
5 Touch Back > Exit Config Menu.
The printer will perform a power‑on reset, and then return to normal operating mode.
Enabling hard disk encryption helps prevent the loss of sensitive data in the event your printer or its hard disk is stolen.
1 From the Embedded Web Server, click Settings > Security > Disk Encryption.
2 From the Disk encryption menu, select Enable.
3 Click Submit.
1 Turn off the printer.
2 Hold down and 6 MNO while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. Once the printer is fully powered up, the touch screen displays a list of functions, instead of standard home screen icons such as Copy or Fax.
3 Touch Disk Encryption > Enable.
4 Touch Yes to proceed with disk wiping.
A status bar will indicate the progress of the disk wiping task. After the disk has been encrypted, the printer will return to the Enable/Disable screen.

Securing the hard disk and other installed memory 144
5 Touch Back, and then Exit Config Menu.
The printer will power‑on reset, and then return to normal operating mode.

Maintaining the printer 145
Periodically, certain tasks are required to maintain optimum performance of your printer.
1 Make sure that the printer is turned off and unplugged from the wall outlet.
2 Remove paper from the standard exit bin.
3 Dampen a clean, lint‑free cloth with water.
4 Wipe only the outside of the printer, making sure to include the standard exit bin.
5 Make sure the paper support and standard exit bin are dry before beginning a new print job.
Clean the printhead lenses when you encounter print quality problems.
1 Open the front door.


Maintaining the printer 146
2 Slide the release lever to the left to unlock the cover.

3 Open the cover.


Maintaining the printer 147
4 Locate the printhead wipers.

5 Gently pull the printhead wipers out until it stops, and then slowly slide them back into place.


Maintaining the printer 148
6 Close the cover.

7 Slide the release lever to the right to lock the cover.


Maintaining the printer 149
8 Close the front door.

1 Open door G.


Maintaining the printer 150
2 Pull out the hole punch box.

3 Empty the container.


Maintaining the printer 151
4 Insert the emptied hole punch box back into the finisher until it stops.

5 Close door G.
Choose a cool, clean storage area for the printer supplies. Store supplies right side up in their original packing until you are ready to use them.
Do not expose supplies to:
A message appears on the display when a replacement supply item is needed or when maintenance is required.
From the home screen, touch Status/Supplies > View Supplies.

Maintaining the printer 152
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Device Status.
To order parts and supplies in the U.S., contact Lexmark at 1-800-539-6275 for information about Lexmark authorized supplies dealers in your area. In other countries or regions, go to the Lexmark support Web site at www.lexmark.com or contact the place where you purchased the printer.
When 88.xx [color] cartridge low or 88.xx [color] cartridge nearly low appears, order a new cartridge.
When 88 Replace [color] cartridge appears, replace the specified cartridge.
Estimated cartridge yield is based on the ISO/IEC 19798 standard (with about 5% coverage per color). Extremely low print coverage (less than 1.25% for a color) for extended periods of time may negatively affect actual yield for that color and may cause cartridge parts to fail prior to exhaustion of toner.
Part name Part number
Black high‑yield toner cartridge C950X2KG
Yellow high‑yield toner cartridge C950X2YG
Magenta high‑yield toner cartridge C950X2MG
Cyan high‑yield toner cartridge C950X2CG
When 84.xx [Color] photoconductor low or 84.xx [Color] photoconductor nearly low appears, order a replacement photoconductor unit.
When 84.xx Replace [color] photoconductor appears, replace the specified photoconductor.
Part name Part number
Photoconductor unit

Maintaining the printer 153
Part name Part number
CMY (Cyan, Magenta, Yellow) Photoconductor Kit
When 82.xx Waste toner bottle nearly full appears, order a replacement waste toner bottle.
When 82.xx Replace waste toner bottle appears, replace the waste toner bottle.
Part name Part number
Waste toner bottle C950X76G
When Staples Low or Staples Empty appears, order the specified staple cartridge.
For more information, see the illustrations inside the stapler door.
Part name Part number
Staple Cartridges‑‑3 pack (Staples G5) 25A0013
Advanced Booklet Staples (Staples G11 and Staples G12) 21Z0357
When [x] Maintenance Kit appears on the printer display, order the indicated maintenance kit to replace the worn parts. All maintenance kit parts except that in the 480K maintenance kit are designed to be user‑replaceable. The kits come with instructions.
Maintenance kit Service part number
160K Maintenance Kit 40X7540
320K (100 V) Maintenance Kit 40X7568
320K (110 V) Maintenance Kit 40X7550
320K (220 V) Maintenance Kit 40X7569
480K Maintenance Kit 40X7560

Maintaining the printer 154
1 Replace the maintenance kit.
2 Reset the maintenance count to zero to clear the 80 scheduled maintenance [x] message.
1 Open the front door.

2 Rotate the release lever counterclockwise to open the cover.


Maintaining the printer 155
3 Lower the cover.

4 Grasp the handle of the photoconductor unit and pull it out of the machine.

5 Unpack the replacement photoconductor unit.

Maintaining the printer 156
6 Align and insert the end of photoconductor unit.

7 Remove the tape from the top of the photoconductor unit.


Maintaining the printer 157
8 Push the tab forward to insert the photoconductor unit.

9 Push the photoconductor unit until it clicks into place


Maintaining the printer 158
10 Gently pull the printhead wipers out until it stops, and then slowly slide them back into place.

11 Close the cover.


Maintaining the printer 159
12 Rotate the release lever clockwise to lock the cover.

13 Close the front door.

1 Open the front door.


Maintaining the printer 160
2 Put your hand under the dent of the toner cartridge, and then slightly lift up the cartridge.

3 Pull out the toner cartridge.


Maintaining the printer 161
4 Unpack the replacement toner cartridge, and then shake it front‑to‑back and side‑to‑side to evenly distribute the toner.

5 Remove the red packing strip from the new cartridge.
6 Insert the new cartridge into the printer.

7 Close the front door.


Maintaining the printer 162
1 Turn the printer off.
2 Open the front door.

3 Remove the used waste toner bottle.

4 Unpack the new waste toner bottle.

Maintaining the printer 163
5 Insert the new waste toner bottle into the printer until it clicks into place.

6 Rotate the release lever counterclockwise to open the cover.


Maintaining the printer 164
7 Lower the cover.

8 Slide out the printhead wipers.


Maintaining the printer 165
9 Slide the printhead wipers back into place.

10 Close the cover.


Maintaining the printer 166
11 Rotate the release lever clockwise to lock the cover.

12 Close the front door.

13 Turn the printer back on.

Maintaining the printer 167
1 Open door G.

2 Grasp the handle of the staple cartridge holder, and then pull out the holder to the right.

3 Pull the staple cartridge out of the finisher.

Maintaining the printer 168

4 Squeeze both sides of the empty staple case with your fingers, and then remove the staple case from the cartridge.

5 Insert the front side of the new staple case into the staple cartridge, and then push the rear side into the cartridge.


Maintaining the printer 169
6 Push the staple cartridge into the finisher until it clicks into place.

7 Close door G.
1 Open door G.


Maintaining the printer 170
2 Press the handles of the staple cartridge to the right, and then take the staple cartridge unit out of the finisher.


Maintaining the printer 171
3 Hold the tabs on both sides of the staple cartridge.


Maintaining the printer 172
4 Rotate the booklet staple cartridge at an angle.


Maintaining the printer 173
5 Lift the booklet staple cartridge out of the unit.

6 Squeeze both sides of the empty staple case with your fingers, and then remove the staple case from the cartridge.


Maintaining the printer 174
7 Insert the front side of the new staple case into the staple cartridge, and then push the rear side into the cartridge.

8 Return the cartridge to its original position, and then gently push the cartridge in until it clicks into place.


Maintaining the printer 175
9 Return the unit to its original position.

10 Close door G.
The printer and options can be safely moved to another location by following these precautions:

Maintaining the printer 176
When shipping the printer, use the original packaging or call the place of purchase for a relocation kit.

Finding advanced networking and administrator information
This chapter covers basic administrative support tasks using the Embedded Web Server. For more advanced system support tasks, see the Networking Guide on the Software and Documentation CD or the Embedded Web Server — Security: Administrator's Guide on the Lexmark support Web site at http://support.lexmark.com.
1 Open an Embedded Web Server associated with your printer.
Type the printer IP address into the address field of your Web browser.
If you do not know the IP address of the printer, you can:
2 Check the virtual display that appears in the top left corner of the screen.
The virtual display works as an actual display would work on a printer control panel, showing printer messages.
1 Type the printer IP address into the address field of your Web browser.
If you do not know the IP address of the printer, you can:
2 Click Device Status.
The device status shows the following:
Configure the printer to send you e‑mail alerts when the supplies are getting low or when the paper needs to be changed or added, or when there is a paper jam.
1 Type the printer IP address into the address field of your Web browser.
Administrative support 177

If you do not know the IP address of the printer, you can:
2 Click Settings.
3 Under Other Settings, click E‑mail Alert Setup.
4 Select the items for notification, and type the e‑mail addresses.
5 Click Submit.
You can view some reports from the Embedded Web Server. These reports are useful for assessing the status of the printer, the network, and supplies.
To view reports from a network printer:
1 Type the printer IP address into the address field of your Web browser.
If you do not know the IP address of the printer you can:
2 Click Reports, and then click the type of report you want to view.
If you want to retain a list of the current menu settings for reference, then print a menu settings page before restoring the factory default settings.
From the home screen, navigate to:
> Settings > General Settings > Factory Defaults > Restore Now >
Administrative support 178

Carefully select paper and specialty media and load it properly to avoid most jams. If jams occur, follow the steps outlined in this chapter.
When a jam occurs, a message indicating the jam location appears on the printer display. Open doors and covers, and remove trays to access jam locations. To resolve any paper jam message, you must clear all jammed paper from the paper path.
Clearing jams 179


Area Area name Jam numbers What to do
1 Cover F 281 4yy.xx Open cover F, and then remove the jammed paper.
2 Door G 455
Open door G, and then remove the jammed paper.
4yy.xx
For staple jams, remove the staple cartridge, and then clear the staple jam.
3 Door H 4yy.xx Open door H, and then remove the jammed paper.
4 Standard exit bin 201–202
Remove all paper from the standard exit bin, and then remove the jammed paper.
5 Standard finisher bin 4yy.xx Remove all paper from the standard finisher bin, and then remove the jammed paper.
6 Finisher bin 1 4yy.xx Remove all paper from the finisher bin 1, and then remove the jammed paper.
7 Finisher bin 2 4yy.xx Remove all paper from the finisher bin 2, and then remove the jammed paper.
8 Door C Tray [x]
24x Open door C, and then remove the jammed paper. Open each tray, and then remove any jams.
9 Tray 5 (high‑capacity feeder)
24x Open the tray, and then remove the jammed paper.
Open the top cover, and then remove the jammed paper. Gently move the tray to the left until it stops, and then remove the jammed paper.
Clearing jams 180


10 Multipurpose feeder 250 Remove all paper from the multipurpose feeder, and then remove the jammed paper.
11 Door B 230 Open door B, and then remove the jammed paper.
Open door A, and then remove the jammed paper.
13 Door D 203 Open door A, and then door D, and then remove the jammed paper.
If the jammed paper is visible in the standard exit bin, then firmly grasp the paper on each side, and then gently pull it out.

Clearing jams 181

1 Open door A by lifting the release latch and lowering the door.
2 Lift the green lever.

3 Firmly grasp the jammed paper on each side, and then gently pull it out.
4 Push the green lever back into place.
5 Close door A.
6 If necessary, touch Continue from the printer control panel.
1 Open door A.
2 If the jammed paper is visible under the fuser, then firmly grasp the paper on each side, and then gently pull it out.
3 Close door A.
4 If necessary, touch Continue from the printer control panel.
If the jammed paper is visible in the standard exit bin, then firmly grasp the paper on each side, and then gently pull it out.
Clearing jams 182


1 Open door A, and then door D by lifting the release latch of each door and lowering the doors.
2 Firmly grasp the jammed paper on each side, and then gently pull it out.

3 Close door D, and then close door A.
4 If necessary, touch Continue from the printer control panel.
Clearing jams 183

1 Lower the multipurpose feeder, and then open door B.

2 Firmly grasp the jammed paper on each side, and then gently pull it out.

3 Close door B.
4 If necessary, touch Continue from the printer control panel.
1 Open door A by lifting the release latch, and then lowering the door.
Clearing jams 184


2 Lift the green lever.

3 Firmly grasp the jammed paper on each side, and then gently pull it out.
4 Push the green lever back into place.
Clearing jams 185

5 Close door A.

6 If necessary, touch Continue from the printer control panel.
1 Open Tray 1.

Clearing jams 186

2 Firmly grasp the jammed paper on each side, and then gently pull it out.

3 Close Tray 1.
4 If necessary, touch Continue, jam cleared from the printer control panel.
1 Check door C, and then firmly grasp the jammed paper and then pull it out.

2 Open the specified tray.
Clearing jams 187

3 Firmly grasp the jammed paper on each side, and then gently pull it out.

4 Close the tray.
5 If necessary, touch Continue, jam cleared from the printer control panel.
1 Pull out the tray until it stops.

Clearing jams 188

2 Firmly grasp the jammed paper on each side, and then gently pull it out.

3 Push the tray gently until it stops.
4 If necessary, touch Continue, jam cleared from the printer control panel.
1 Gently move the tray to the left until it stops.

2 Firmly grasp the jammed paper on each side, and then gently pull it out.

Clearing jams 189

3 Gently put the tray back into position.
4 If necessary, touch Continue, jam cleared from the printer control panel.
1 Gently move the tray to the left until it stops.

2 Open the top cover.

Clearing jams 190

3 Firmly grasp the jammed paper on each side, and then gently pull it out.

4 Close the top cover.

5 Gently put the tray back into position.
6 If necessary, touch Continue, jam cleared from the printer control panel.
Clearing jams 191

1 Remove any jammed pages from the multipurpose feeder.

2 Load paper into the multipurpose feeder.
3 If necessary, touch Continue, jam cleared from the printer control panel.
1 Open door A.
2 Determine where the jam is located, and then remove it: a If the paper is visible under the fuser, firmly grasp it on each side, and then gently pull it out.

b If the paper is not visible, then you will need to remove the fuser unit.
Clearing jams 192

1 Remove the thumbscrew from each side of the fuser unit by rotating them counterclockwise. 2 Lift the handles on each side of the fuser, and then pull to remove the fuser unit.

3 Lift the green lever, firmly grasp the paper on each side, and then gently pull it out.
4 Align the fuser unit using the handles on each side, and then place it back into the printer.

3 Close door A.
4 If necessary, touch Continue from the printer control panel.
Clearing jams 193

1 Open cover F.

2 Firmly grasp the jammed paper on each side, and then gently pull it out.
3 Close cover F.
4 If necessary, touch Continue from the printer control panel.
If the jammed paper is visible in any of the finisher exit bins, then firmly grasp the paper on each side, and then gently pull it out.
Clearing jams 194


1 Open door H.

2 Firmly grasp the jammed paper on each side, and then gently pull it out.

Clearing jams 195

3 Close door H.
4 If necessary, touch Continue from the printer control panel.
1 Open door G.


2 Lift cover G1 lever.
Clearing jams 196

3 Firmly grasp any jammed paper, and then gently pull it out.
4 Move cover G2 to the right, and then remove any jammed paper.
5 Move cover G4 down, and then remove any jammed paper.
6 Move cover G7 to the left, and then remove any jammed paper.
7 Pull handle G9 until the tray is completely open.

8 Lift the inside cover. If the paper is jammed in the rollers, then rotate knob G8 counterclockwise, and then remove the jammed paper.

9 Close door G.
10 If necessary, touch Continue from the printer control panel.
Clearing jams 197

1 Open cover F.

2 Firmly grasp the jammed paper on each side, and then gently pull it out.
3 Close cover F.
4 If necessary, touch Continue from the printer control panel.
1 Open door G.

Clearing jams 198

2 Press the latch to open the stapler door.

3 Lower the latch of the staple cartridge holder, and then pull the staple cartridge holder out of the printer.

4 Use the metal tab to lift the staple guard, and then remove any jammed or loose staples.

Clearing jams 199

5 Close the staple guard.

6 Press down on the staple guard until it clicks into place.
7 Push the staple cartridge holder firmly back into the stapler unit until the staple cartridge holder clicks into place.

8 Close the stapler door.
9 Close door G.
10 If necessary, touch Continue, jam cleared from the printer control panel.
Clearing jams 200
![Page 201 of the Lexmark C 950 user manual — Change [paper source] to [custom type name]](/cdn/reader/c5/c5447e89ce310907a4495e702c5ae8eed252c4319418f7ecb3ef346aa39ca00a/images/page-201.webp?w=400)
Solving basic printer problems
If there are basic printer problems, or the printer is unresponsive, make sure:
Once you have checked each of these possibilities, turn the printer off, wait for about 10 seconds, and then turn the printer back on. This often fixes the problem.
An error has occured with the Flash Drive. Please remove and re-insert the drive.
Try one or more of the following:
Bin 2 is unable to lower, remove paper and check for an obstruction
Try one or more of the following:
Try one or more of the following:
Troubleshooting 201
![Page 202 of the Lexmark C 950 user manual — Change [paper source] to [paper size] [paper type] load [orientation]](/cdn/reader/c5/c5447e89ce310907a4495e702c5ae8eed252c4319418f7ecb3ef346aa39ca00a/images/page-202.webp?w=400)
Try one or more of the following
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Troubleshooting 202

Try one or more of the following:
Close the specified cover to clear the message.
Close the specified door.
The printer attempted a hard disk recovery on a corrupted hard disk, and the hard disk cannot be repaired. The hard disk must be reformatted.
Touch Format disk to reformat the printer hard disk and clear the message.
1 Empty the hole punch box.
For instructions on emptying the hole punch box, from the printer control panel touch More Information.
2 Reinsert the hole punch box into the finisher, and then touch Continue to clear the message.
Error reading USB drive. Remove USB.
An unsupported USB device has been inserted. Remove the USB device, and then install a supported one.
Error reading USB hub. Remove hub.
An unsupported USB hub has been inserted. Remove the USB hub, and then install a supported one.
Try one or more of the following:
Troubleshooting 203
![Page 204 of the Lexmark C 950 user manual — Load [src] with [size]](/cdn/reader/c5/c5447e89ce310907a4495e702c5ae8eed252c4319418f7ecb3ef346aa39ca00a/images/page-204.webp?w=400)
Insert the hole punch box into the finisher, and then touch Continue to clear the message.
Insert the specified tray into the printer.
Try one or more of the following:
Try one or more of the following:
If the printer finds a tray that has the correct paper type and size, it feeds from that tray. If the printer cannot find a tray with the correct paper type and size, it prints from the default paper source. • Cancel the print job.
Try one or more of the following:
If the printer finds a tray that has the correct paper type and size, it feeds from that tray. If the printer cannot find a tray with the correct paper type and size, it prints from the default paper source. • Cancel the print job.
Try one or more of the following:
If the printer finds a tray that has the correct paper type and size, it feeds from that tray. If the printer cannot find a tray with the correct paper type and size, it feeds from the default paper source.
Troubleshooting 204
![Page 205 of the Lexmark C 950 user manual — Load Manual Feeder with [paper type] [paper size]](/cdn/reader/c5/c5447e89ce310907a4495e702c5ae8eed252c4319418f7ecb3ef346aa39ca00a/images/page-205.webp?w=400)
Try one or more of the following:
If the printer finds a tray that has the correct paper type and size, it feeds from that tray. If the printer cannot find a tray with the correct paper type and size, it feeds from the default paper source. • Cancel the print job.
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Troubleshooting 205
![Page 206 of the Lexmark C 950 user manual — Remove paper from [linked set bin name]](/cdn/reader/c5/c5447e89ce310907a4495e702c5ae8eed252c4319418f7ecb3ef346aa39ca00a/images/page-206.webp?w=400)
Try one or more of the following:
If the printer finds a tray that has the correct paper type and size, then it feeds from that tray. If the printer cannot find a tray with the correct paper type and size, then it prints from the default source.
Try one or more of the following:
Remove the stack of paper from the standard exit bin.
Remove the paper from the specified bin. The printer automatically senses paper removal and resumes printing.
If removing the paper does not clear the message, then touch Continue.
Remove the paper from all of the bins. The printer automatically senses paper removal and resumes printing.
If removing the paper does not clear the message, then touch Continue.
Remove paper from the specified bin. The printer automatically detects paper removal and resumes printing.
If removing the paper does not clear the message, then touch Continue.
Print quota exceeded. Print job canceled.
The print job has been cancelled because the print quota has been exceeded. Contact your system support person.
Troubleshooting 206
![Page 207 of the Lexmark C 950 user manual — 32.xx [color] cartridge part number unsupported by device](/cdn/reader/c5/c5447e89ce310907a4495e702c5ae8eed252c4319418f7ecb3ef346aa39ca00a/images/page-207.webp?w=400)
Print quota exceeded. Print job incomplete.
The print job did not complete because the print quota has been exceeded. Contact your system support person.
Try one or more of the following:
Remove any remaining packaging material from the specified location.
Touch Continue to delete the specified job.
The camera mode does not support PictBridge.
Unplug the camera, change the mode and plug the camera back into the printer.
An unsupported disk has been inserted. Remove the unsupported disk, and then install a supported one.
Try one or more of the following:
1 Remove and reinstall the specified print cartridge.
For instructions on removing a print cartridge, touch More Information.
2 Touch Continue to clear the message.
Remove the unsupported toner cartridge, and then install a supported one.
Troubleshooting 207

Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
The printer was unable to restore some or all of the confidential or held jobs on the printer hard disk.
Touch Continue to clear the message.
The printer deleted some held jobs in order to process current jobs.
Touch Continue to clear the message.
Troubleshooting 208

Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Replace the specified cartridge to continue printing.
Try one or more of the following:
Try one or more of the following:
Troubleshooting 209
![Page 210 of the Lexmark C 950 user manual — 55 Unsupported option in slot [x]](/cdn/reader/c5/c5447e89ce310907a4495e702c5ae8eed252c4319418f7ecb3ef346aa39ca00a/images/page-210.webp?w=400)
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
1 Turn the printer off.
2 Unplug the power cord from the wall outlet.
3 Remove the unsupported option card from the printer system board, and then replace it with a supported card.
4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
Troubleshooting 210

Try one or more of the following:
The printer discards any data received through the parallel port. • Make sure the Parallel Buffer menu item is not set to Disabled.
Try one or more of the following:
The printer discards any data received through the serial port. • Make sure the Serial Buffer menu is not set to Disabled.
Try one or more of the following:
The printer discards any data received through the USB port. • Make sure the USB Buffer menu item is not set to Disabled.
Try one or more of the following:
The printer discards any data received through the parallel port. • Make sure the Parallel Buffer menu item is not set to Disabled.
Try one or more of the following:
The printer discards any data received through the USB port. • Make sure the USB Buffer menu is not set to Disabled.
Something has changed in the printer to invalidate the held jobs. Possible changes include:
Troubleshooting 211

Touch Continue to clear the message.
1 Turn the printer off.
2 Unplug the power cord from the wall outlet.
3 Remove the excess disks.
4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
1 Turn the printer off.
2 Unplug the power cord from the wall outlet.
3 Remove the excess flash memory.
4 Connect the power cord to a properly grounded outlet.
5 Turn the printer back on.
1 Turn the printer off.
2 Unplug the power cord from the wall outlet.
3 Remove the additional trays.
4 Connect the power cord to a properly grounded outlet.
5 Turn the printer back on.
Try one or more of the following:
Try one or more of the following:
Troubleshooting 212
![Page 213 of the Lexmark C 950 user manual — 84 unsupported [color] photoconductor](/cdn/reader/c5/c5447e89ce310907a4495e702c5ae8eed252c4319418f7ecb3ef346aa39ca00a/images/page-213.webp?w=400)
Try one or more of the following:
Contact customer support, and report the message. The printer is scheduled for maintenance.
80 Replace paper pick rollers in [paper source], use parts and instructions in tray 1 compartment
Try one or more of the following:
1 Replace the waste toner bottle.
For instructions on replacing the waste toner bottle, from the printer control panel touch More Information.
2 Touch Continue to clear the message and continue printing.
Order a replacement waste toner bottle immediately.
1 Replace the waste toner bottle.
For instructions on installing the waste toner bottle, from the printer control panel touch More Information.
2 Touch Continue to clear the message and continue printing.
Reinsert the waste toner bottle into the printer.
Remove the specified photoconductor, and then install a supported one.
Troubleshooting 213

1 Order a replacement photoconductor immediately.
2 When print quality is reduced, install the new photoconductor, following the instruction sheet that came with the replacement part.
3 Touch Continue to clear the message and continue printing.
Install the specified color photoconductor, following the instruction sheet that came with the replacement part.
1 Replace the photoconductor, following the instruction sheet that came with the replacement part.
2 From the printer control panel, touch Continue to clear the message and continue printing.
1 Order a replacement toner cartridge immediately.
2 Touch Continue to clear the message and continue printing.
The specified print cartridge is very low. If you do not have a replacement toner cartridge, then order one immediately.
1 For instructions on replacing a print cartridge, from the printer control panel touch More Information.
2 Touch Continue to clear the message and continue printing.
The specified print or toner cartridge is empty.
1 Replace the specified cartridge.
For instructions on replacing cartridge, from the printer control panel, touch More Information.
2 Touch Continue to clear the message and continue printing.
The printer automatically clears the message in 30 seconds, and then disables the download emulator on the firmware card.
Troubleshooting 214

The PDF files may contain unavailable fonts.
1 Open the document you want to print in Adobe Acrobat.
2 Click the printer icon > Advanced > Print as image > OK > OK.
The printer self test failed. Turn the printer off, wait about 10 seconds, and then turn the printer back on.
If Performing Self Test and Ready do not appear, turn the printer off and contact Customer Support.
Make sure the flash drive is supported.
Try one or more of the following:
Make sure there is no problem with your printer
From the printer control panel, check the status. If necessary, follow the recovery instructions.
Make sure the printer is ready to print
Make sure Ready appears on the display before sending a print job.
Check if a supply is missing or needs replacement
Remove and then reinstall or replace the supply.
Check if the standard exit bin is full
Remove the paper stack from the standard exit bin.
Check if the paper tray is empty
Load paper in the tray.
Make sure the correct printer software is installed
Troubleshooting 215

Make sure the internal print server is working properly
The printer software is available on the Lexmark Web site at http://support.lexmark.com.
Make sure you are using a recommended USB, serial, or Ethernet cable
For more information, visit the Lexmark Web site at http://support.lexmark.com.
Make sure printer cables are securely connected
Check the cable connections to the printer and print server to make sure they are secure.
For more information, see the setup documentation that came with the printer.
These are possible solutions. Try one or more of the following:
Partial job, no job, or blank page prints
The print job may contain a formatting error or invalid data.
If you are printing from the Internet, then the printer may be reading multiple job titles as duplicates and deleting all jobs except the first one.
Make sure the printer has sufficient memory
Free up additional printer memory by scrolling through the list of held jobs and deleting some of them.
Try one or more of the following:
Reduce the complexity of the print job
Eliminate the number and size of fonts, the number and complexity of images, and the number of pages in the print job.
Turn off the Page Protect setting
From the home screen, navigate to:
Troubleshooting 216

> Settings > General Settings > Print Recovery > Page Protect > Off >
Change the environmental settings
When using Eco‑Mode or Quiet Mode settings, you may notice a reduction in performance.
Check the paper type and paper size settings
Make sure the paper type setting matches the paper loaded in the tray:
1 From the printer control panel Paper menu, check the paper type and paper size settings.
These are possible solutions. Try one or more of the following:
Load the same size and type of paper
Use the same Paper Size and Paper Type settings
These are possible solutions. Try one or more of the following:
Make sure Collate is set to On
From the Finishing menu or Print Properties, set Collate to On.
Troubleshooting 217

Reduce the complexity of the print job
Reduce the complexity of the print job by eliminating the number and size of fonts, the number and complexity of images, and the number of pages in the job.
Make sure the printer has enough memory
Add printer memory or an optional hard disk.
Increase the Print Timeout value
1 From the home screen, navigate to:
> Settings > General Settings > Timeouts
2 Touch the left or right arrow next to Print Timeout until the desired value appears.
3 Touch Submit.
Check the system log for relevant details
1 Type the printer IP address or host name in the address field of your Web browser.
If you do not know the IP address or host name of the printer, then you can:
2 Click Settings or Configuration.
3 Click Device Solutions > Solutions (eSF) > System tab > Log.
4 From the Filter menu, select an application status.
5 From the Application menu, select an application, and then click Submit.
Make sure the file name you want to scan to is not already in use
Verify that the file to which you want to scan is not open by another application or user.
To help prevent errors, make sure either “Append time stamp” or “Overwrite existing file” is selected in the destination configuration settings.
Adjust the scan settings
In the destination configuration settings, lower the scan settings. For example, lower the scan resolution, disable Color, or change the Content type to Text.
Troubleshooting 218

If you still cannot isolate the problem, then contact customer support.
Make sure the bookmark pointing to the form is in the Bookmarks root folder
If the bookmark pointing to the form was created in a subfolder of the Bookmarks folder, then it will not be available under the Forms solution. Delete the bookmark and recreate it under the Bookmarks root folder.
Make sure the bookmark is pointing to the correct location
The printer does not validate bookmarks. If the URL or network location that was specified when the bookmark was created is incorrect, then the printer will not be able to access the document.
Make sure the bookmark is created with Forms and Favorites
If the bookmark is created using another application, then it cannot be accessed in Forms and Favorites.
Make sure the printer authentication is configured
If the application is configured to use MFP authentication credentials, then the printer authentication settings must be configured from the Embedded Web Server.
For more information on configuring the printer authentication settings, see the Embedded Web Server Administrator's Guide available on www.lexmark.com.
Make sure destination is shared and has a valid network address
Check that the folder or source file is set to be shared across the network.
If the destination has been moved, then the network address may have changed. The destination network address can be accessed from the Embedded Web Server.
Make sure the printer is connected to the network
Make sure that all appropriate network cables are securely connected and that the network settings of the printer are correctly configured. For information on networking the printer, see the Networking Guide on the Software and Documentation CD that came with the printer.
If the source file and printer reside in different domains, then make sure the domain information is specified
If the source file exists within a different domain than the printer, then you can edit the destination from the application configuration page and enter the appropriate domain information in the Network Address and Network Domain fields. If you do not know the network address of the computer where your source file resides, then consult your system support person.
You can also add the domain name to the Domain Search Order list under the printer network setup.
Check the system log for relevant details
1 Type the printer IP address or host name in the address field of your Web browser.
Troubleshooting 219 · Contact customer support

If you do not know the IP address or host name of the printer, then you can:
2 Click Settings or Configuration.
3 Click Device Solutions > Solutions (eSF), or click Embedded Solutions.
4 Click System tab > Log.
5 From the Filter menu, select an application status.
6 From the Application menu, select an application, and then click Submit.
Try one or more of the following:
Turn the printer off, wait for about 10 seconds, and then turn the printer on.
Check to see if the option is connected to the printer
1 Turn the printer off using the power switch.
2 Unplug the power cord from the wall outlet, and then from the printer.
3 Check the connection between the option and the printer.
Make sure the option is installed correctly
Print a menu settings page and check to see if the option is listed in the Installed Options list. If the option is not listed, then reinstall it. For more information, see the hardware setup documentation that came with the option, or go to www.lexmark.com to view the option instruction sheet.
Make sure the option is selected
From the computer you are printing from, select the option.
For more information, see “Adding available options in the print driver” on page 42.
Try one or more of the following:
Make sure the paper is loaded correctly
1 Open the paper tray.
2 Check for paper jams or misfeeds.
Troubleshooting 220 · Reset the printer

3 Make sure the paper guides are aligned against the edges of the paper.
4 Make sure the paper tray closes properly.
Turn the printer off, wait about 10 seconds, and then turn the printer on.
Make sure the paper tray is installed correctly
If the paper tray is listed on the menu settings page, but paper jams when it enters or exits the tray, then it may not be properly installed. Reinstall the paper tray. For more information, see the hardware setup documentation that came with the paper tray, or go to http://support.lexmark.com to view the paper tray instruction sheet.
Check the drawer connection
Make sure the 2,000‑sheet drawer is properly connected to the printer.
If the tray is empty, then load paper in the tray or feeder
Open the side door of the tray or feeder, and then remove any jammed paper.
Make sure the memory card is securely connected to the printer system board.
Make sure the flash memory card is securely connected to the printer system board.
Make sure the printer hard disk is securely connected to the printer system board.

Try one or more of the following:
Check the Internal Solutions Port (ISP) connections
Make sure the ISP is securely connected to the printer system board.
Make sure you are using the correct cable and that it is securely connected to the Internal Solutions (ISP) port.
Make sure the network software is configured correctly
For information on installing the network printing software, see the Networking Guide on the Software and Documentation CD.
Try one or more of the following:
Check the print server connections
Make sure the network software is configured correctly
For more information on installing the network printing software, do the following:
1 Open the Software and Documentation CD.
2 Click Additional.
3 Under Publications on this CD, select Networking Guide.
Check the USB/parallel interface card connection
Make sure the USB/parallel interface card is securely connected to the printer system board.
Make sure you are using the correct cable and that it is securely connected.
Troubleshooting 222 · Check the cable · Check the cable

These are possible solutions. Try one or more of the following:
Use recommended paper and specialty media. For more information, see the chapter about paper and specialty media guidelines.
Make sure there is not too much paper in the paper tray
Make sure the stack of paper you load does not exceed the maximum stack height indicated in the tray or on the multipurpose feeder.
Check the paper guides
Move the guides in the tray to the correct positions for the paper size loaded.
The paper may have absorbed moisture due to high humidity
Check the paper path
The paper path is not clear. Clear jammed paper from the entire paper path, and then touch Continue.
Turn on Jam Recovery
1 From the home screen, navigate to:
> Settings > General Settings > Print Recovery
2 Touch the arrows next to Jam Recovery until On or Auto appears.
Troubleshooting 223 · Check the paper · 3 Touch

If the solutions here do not correct the problem, contact customer support. You may have a printer part that requires adjustment or replacement.
Try one or more of the following:
Make sure there is no packing material left on the toner or print cartridge
Remove the cartridge and make sure the packing material is properly removed. Reinstall the cartridge.
Make sure the toner or print cartridge is not low on toner
When 88.xx [color] cartridge low appears, make sure that toner is distributed evenly among all four cartridges:
1 Remove the cartridge.
2 Firmly shake the cartridge side-to-side and front-to-back several times to redistribute the toner.
3 Reinsert the cartridge.
If the problem continues, then the printer may need to be serviced. For more information, contact customer support.
If you are using downloaded fonts, verify that the fonts are supported by the printer, the host computer, and the software program.
Troubleshooting 224

Try one or more of the following:
Move the width and length guides in the tray to the correct positions for the paper size loaded.
Check the paper size setting
Make sure the paper size setting matches the paper loaded in the tray:
1 From the printer control panel Paper menu, check the Paper Size setting.
You may notice fine, horizontal lines in photographs or pages with a high concentration of color. This can occur when the printer is in Quiet Mode. To fix this, set Quiet Mode to Off (Image/Photo).
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE
Check the paper type and weight settings
Make sure the paper type and weight settings match the paper loaded in the tray:
1 From the printer control panel Paper menu, check the Paper Type and Paper Weight settings.
Make sure the photoconductor unit is not defective
Replace the defective photoconductor unit.
Troubleshooting 225 · Check the guides

Make sure the toner cartridge is not low on toner
When 88.xx [color] cartridge low appears, make sure the toner is distributed evenly within the toner cartridge.
1 Remove the toner cartridge.
2 Firmly shake the cartridge side-to-side and front-to-back several times to redistribute the toner.
3 Reinsert the toner cartridge.
If the problem continues, the printer may need to be serviced. For more information, contact customer support.
ABCDE
ABCDE ABCDE
Check the background darkness or removal setting
Try one or more of the following:
Make sure there is no worn or defective print cartridge
Replace the worn or defective print cartridge.
ABCD ABCD ABCD
These are possible solutions. Try one or more of the following:
Troubleshooting 226

Check the paper guides
Move the guides in the tray to the correct positions for the paper size loaded.
Check the paper size setting
Make sure the paper size setting matches the paper loaded in the tray:
1 From the printer control panel Paper menu, check the Paper Size setting.
ABCDE ABCDE
ABCDE ABCDE ABCDE
Try one or more of the following:
Make sure there is no defective toner cartridge
Replace the defective toner cartridge.
Make sure the photoconductor unit is not defective
Replace the defective photoconductor unit.
Make sure the transfer module is not defective
Replace the defective transfer module.
Clean the printhead lenses
1 Open the front door, and then the internal cover.
2 Locate the printhead wipers.
3 Gently pull the printhead wiper out until it stops, and then slowly slide it back into place.
4 Clean the remaining three printhead lenses.
Troubleshooting 227

Try one or more of the following:
Check the paper type and weight settings
Make sure the paper type and weight settings match the paper loaded in the tray or feeder:
1 From the printer control panel Paper menu, check the Paper Type and Paper Weight settings.
Load paper from a fresh package
Paper absorbs moisture due to high humidity. Store paper in its original wrapper until you use it.
Try one or more of the following:
Load paper from a fresh package
The paper may have absorbed moisture due to high humidity. Store paper in its original wrapper until you use it.
Check the paper type and weight settings
Make sure the paper type and weight settings match the paper loaded in the tray or feeder:
1 From the printer control panel Paper menu, check the Paper Type and Paper Weight settings.
Avoid textured paper with rough finishes
Make sure there is no defective print cartridge
Replace the worn or defective print cartridge.
Troubleshooting 228

Make sure the transfer belt is not defective
Replace the defective transfer belt. For more information, see the instruction sheet that came with the replacement part.
Make sure the fuser is not defective
Replace the defective fuser. For more information, see the instruction sheet that came with the replacement part.
Try one or more of the following:
Check the darkness, brightness, and contrast settings
The Toner Darkness setting may be too dark, the Brightness setting may be too dark, or the Contrast setting may be too high.
Load paper from a fresh package
The paper may have absorbed moisture due to high humidity. Store paper in its original wrapper until you use it.
Avoid textured paper with rough finishes
Check the Paper Type setting
Make sure the paper type setting matches the paper loaded in the tray or feeder:
Troubleshooting 229

Try one or more of the following:
Check the darkness, brightness, and contrast settings
The Toner Darkness setting may be too light, the Brightness setting may be too light, or the Contrast setting may be too low.
Load paper from a fresh package
The paper may have absorbed moisture from high humidity. Store paper in its original wrapper until you use it.
Avoid textured paper with rough finishes
Check the Paper Type setting
Make sure the Paper Type setting matches the paper loaded in the tray or feeder:
Try one or more of the following:
Make sure the photoconductor unit is not defective
The photoconductor unit may be defective if marks occur repeatedly in only one color and multiple times on a page.
Troubleshooting 230

Make sure the fuser is not defective
The fuser may be defective if the marks occur down repeatedly in all colors.
Try one or more of the following:
Check the paper guides
Adjust the length and width guides in the tray to the correct positions for the paper size loaded.
Make sure you are using paper that meets the printer specifications.
Make sure the printer is clean or is not contaminated with paper dust
Clean the exterior of the printer
1 Make sure that the printer is turned off and unplugged from the wall outlet.
2 Remove paper from the standard exit bin.
3 Dampen a clean, lint-free cloth with water.
4 Wipe only the exterior of the printer, making sure to include the standard exit bin.
5 Make sure the paper support and standard exit bin are dry before beginning a new print job.
Make sure the paper feed rollers are clean and are not contaminated with dust
1 Turn the printer off using the power switch, and then unplug the power cord from the wall outlet.
2 Remove the paper feed rollers.
3 Dampen a clean, lint-free cloth with water.
Troubleshooting 231 · Check the paper

4 Clean the paper feed rollers.
5 Reinstall the paper feed rollers.
Make sure the photoconductor is not defective and is installed correctly
Remove and then reinstall the photoconductor. If the problem continues, then the photoconductor may need to be replaced.
Try one or more of the following:
Ensure that the fill pattern is correct
If the fill pattern is incorrect, choose a different fill pattern from your software program.
Check the paper type
Troubleshooting 232

Make sure the print cartridge is not low on toner
When 88.xx [color] cartridge low appears, make sure the toner is distributed evenly within the print cartridge:
1 Remove the print cartridge.
2 Firmly shake the cartridge side-to-side and front-to-back several times to redistribute the toner.
3 Reinsert the print cartridge.
If the problem continues, the printer may need to be serviced. For more information, contact Customer Support.
ABCDE ABCDE ABCDE
Try one or more of the following:
Select another tray or feeder
Make sure there is no worn, defective, or empty print cartridge
Replace the worn, defective, or empty print cartridge.
Try one or more of the following:
Make sure the toner cartridge is installed correctly or is not defective
Reinstall or replace the defective toner cartridge.
Make sure the transfer module is not worn or defective
Replace the worn or defective transfer module.
Make sure the photoconductor unit is not worn or defective
Replace the word or defective photoconductor unit.
Troubleshooting 233

Make sure the fuser is not worn or defective
Replace the worn or defective fuser.
Make sure the printer has recalibrated recently
Perform color adjust from the Quality menu.
Make sure the application has not specified an off‑white background
Check the application settings.
Make sure no toner is in the paper path
Contact customer support.
Try one or more of the following:
Check the paper type and weight settings
Make sure the paper type and weight settings match the paper loaded in the tray or feeder:
1 From the printer control panel Paper menu, check the Paper Type and Paper Weight settings. Change the Paper Weight setting from Normal to Heavy.
Check the paper texture setting
From the printer control panel Paper menu, make sure the Paper Texture setting matches the paper loaded in the tray or feeder. If necessary, change the Paper Texture setting from Normal to Rough.
Make sure the fuser is not worn or defective
Replace the worn or defective fuser. For more information, see the instruction sheet that came with the replacement part.
Troubleshooting 234

Try one or more of the following:
Use only transparencies that meet the printer specifications.
Check the paper type setting
Make sure the paper type setting is set to Transparency:
1 From the printer control panel Paper menu, check the Paper Type setting.
This section helps answer some basic color‑related questions and describes how some of the features provided in the Quality Menu can be used to solve typical color problems.
What is RGB color?
Red, green, and blue light can be added together in various amounts to produce a large range of colors observed in nature. For example, red and green can be combined to create yellow. Televisions and computer monitors create colors in this manner. RGB color is a method of describing colors by indicating the amount of red, green, or blue needed to produce a certain color.
What is CMYK color?
Cyan, magenta, yellow, and black (known as CMYK color) inks or toners can be printed in various amounts to produce a large range of colors observed in nature. For example, cyan and yellow can be combined to create green. Printing presses, inkjet printers, and color laser/LED printers create colors in this manner. CMYK color is a method of describing colors by indicating the amount of cyan, magenta, yellow, and black needed to reproduce a particular color.
How is color specified in a document to be printed?
Software applications typically specify document color using RGB or CMYK color combinations. Additionally, they commonly let you modify the color of each object in a document. For more information, see the software application Help section.
How does the printer know what color to print?
When you print a document, information describing the type and color of each object is sent to the printer. The color information is passed through color conversion tables that translate the color into the appropriate amounts of cyan, magenta, yellow, and black toner needed to produce the desired color. The object type information lets different color conversion tables be used for different types of objects. For example, it is possible to apply one type of color conversion table to text while applying a different color conversion table to photographic images.
Troubleshooting 235 · Check the transparencies

Should I use PostScript or PCL emulation printer software? What settings should I use for the best color?
The PostScript driver is strongly recommended for best color quality. The default settings in the PostScript driver provide preferred color quality for the majority of printouts.
Why doesn't the printed color match the color that I see on the computer screen?
The color conversion tables used in Auto Color Correction mode generally approximate the colors of a standard computer monitor. However, because of technology differences that exist between printers and monitors, there are many colors that can also be affected by monitor variations and lighting conditions. For recommendations on how the printer color sample pages may be useful in solving certain color‑matching problems, see the question, “How can I match a particular color (such as a color in a corporate logo)?”
The printed page appears tinted. Can I slightly adjust the color?
Sometimes you may consider printed pages to appear tinted (for example, everything printed seems to be too red). This can be caused by environmental conditions, paper type, lighting conditions, or user preference. In these instances, adjusting the Color Balance setting may create more preferable color. Color Balance lets you make subtle adjustments to the amount of toner being used in each color plane. Selecting positive (or negative) values for cyan, magenta, yellow, and black under the Color Balance menu will slightly increase (or decrease) the amount of toner used for the chosen color. For example, if you believe the overall printed page to be too red, then decreasing both magenta and yellow could potentially improve color.
My color transparencies seem dark when being projected. Is there anything I can do to improve the color?
This problem most commonly occurs when projecting transparencies with reflective overhead projectors. To obtain the highest projected color quality, transmissive overhead projectors are recommended. If a reflective projector must be used, then adjusting the Toner Darkness setting to 1, 2, or 3 will lighten the transparency.
Make sure to print on the recommended type of color transparencies. For more information about the paper and media specifications, see the User's Guide on the Software and Documentation CD.
What is manual color correction?
The color conversion tables applied to each object when using the default Auto Color Correction setting generate preferred color for the majority of documents. Occasionally, you may want to apply a different color table mapping. This customization is accomplished using the Manual Color menu and the Manual Color Correction setting.
Manual Color Correction applies to RGB and CMYK color conversion table mappings as defined in the Manual Color menu.
You can select any of the different color conversion tables for RGB or CMYK:
Color conversion table Settings
Troubleshooting 236

How can I match a particular color (such as a corporate logo)?
Occasionally, you may have a need for the printed color of a particular object to closely match a specific color. For example, you may need to match the color of a corporate logo. While instances can occur in which the printer cannot exactly reproduce the desired color, you should be able to identify adequate color matches for the majority of cases.
The Color Samples menu item can provide useful information in helping solve this particular type of color‑matching problem. The nine Color Samples values correspond to color conversion tables in the printer. Selecting any of the Color Samples values generates a multiple‑page printout consisting of hundreds of colored boxes. Either a CMYK or RGB combination is located on each box, depending on the table selected. The observed color of each box is obtained by passing the CMYK or RGB combination labeled on the box through the selected color conversion table.
You can examine the color samples pages and identify the box whose color is the closest to the desired color. The color combination labeled on the box can then be used for modifying the color of the object in a software application. For instructions, see the software application Help. Manual Color Correction may be necessary to utilize the selected color conversion table for the particular object.
Selecting which Color Samples pages to use for a particular color‑matching problem depends on the Color Correction setting being used (Auto, Off, or Manual), the type of object being printed (text, graphics, or images), and how the color of the object is specified in the software application (RGB or CMYK combinations). When the printer Color Correction setting is set to Off, the color is based on the print job information; no color conversion is implemented.
Note: The Color Samples pages are not useful if the software application does not specify colors with RGB or CMYK combinations. Additionally, certain situations exist where the software application or the computer operating system adjusts the RGB or CMYK combinations specified in the application through color management. The resulting printed color may not be an exact match of the Color Samples pages.
The following table can help identify which Color Sample pages to use for color matching.
Color specification and object to be printed
Color Correction setting Sample pages to use
RGB—Text Auto sRGB Vivid
Manual Manual Color RGB Text Setting
RGB—Graphic Auto sRGB Vivid
Manual Manual Color RGB Graphic Setting
RGB—Image Auto sRGB Display
Manual Manual Color RGB Image Setting
CMYK—Text Auto US CMYK or Euro CMYK
Manual Manual Color CMYK Text Setting
CMYK—Graphic Auto US CMYK
Manual Manual Color CMYK Graphic Setting
CMYK—Image Auto US CMYK
Manual Manual Color CMYK Image Setting
Troubleshooting 237

What are Detailed Color Samples and how do I access them?
These pages require the use of the Embedded Web Server. The Embedded Web Server is a series of resident pages stored in the network printer firmware. To access these pages, browse to the IP address of the network printer. Click Configuration Menu, and then click Detailed Color Samples.
For more information about using the Embedded Web Server, see the User's Guide on the Software and Documentation CD.
Detailed Color Samples are pages similar to the default pages of color samples accessible from the Quality menu using the printer control panel. The default color samples available using this method have an increment value of 10% for red, green, and blue. If you find a value on this page that is close, but would like to scan more colors in a nearby area, then you can use the Detailed Color Samples to select the desired color values and a more specific increment. This provides a way to print multiple pages of colored boxes that surround a specific color of interest.
There are nine conversion tables available with the following three options:
The process can be duplicated for Cyan (C), Magenta (M), Yellow (Y), and Black (K) color conversion tables, too. Collectively, these values are known as CMYK color. The default increment is 10% for Black and 20% each for Cyan, Magenta, and Yellow.
Try one or more of the following:
Make sure the printer and computer are turned on and connected to the same network.
Proxy servers may block or restrict you from accessing certain Web sites including the Embedded Web Server. For more information, contact your system support person.
When you contact customer support, describe the problem you are experiencing, the printer control panel light sequence, and the troubleshooting steps you have already taken to find a solution.
You need to know your printer model type and serial number. For more information, see the label on the inside top front cover of the printer. The serial number is also listed on the menu settings page.
Troubleshooting 238

Lexmark has various ways to help you solve your printing problem. Visit the Lexmark Web site at http://support.lexmark.com, and then select one of the following:
You can browse our library of manuals, support documentation, drivers, and other downloads to help you solve common problems.
E-mail You can send an e-mail to the Lexmark team, describing your problem. A service representative will respond and provide you with information to solve your problem.
Live chat You can chat directly with a service representative. They can work with you to solve your printer problem or provide assistance through Assisted Service where the service representative can remotely connect to your computer through the Internet to troubleshoot problems, install updates, or complete other tasks to help you successfully use your Lexmark product.
Telephone support is also available. In the U.S. or Canada, call 1-800-539-6275. For other countries or regions, visit the Lexmark Web site at http://support.lexmark.com.
Troubleshooting 239 · Tech Library

Product name:
Machine type:
Model(s):
The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.
References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.
For Lexmark technical support, visit http://support.lexmark.com.
For information on supplies and downloads, visit www.lexmark.com.
2015 Lexmark International, Inc.
All rights reserved.
The Software Program and any related documentation are "Commercial Items," as that term is defined in 48 C.F.R. 2.101, "Computer Software" and "Commercial Computer Software Documentation," as such terms are used in 48 C.F.R. 12.212 or 48 C.F.R. 227.7202, as applicable. Consistent with 48 C.F.R. 12.212 or 48 C.F.R. 227.7202-1 through 227.7207-4, as applicable, the Commercial Computer Software and Commercial Software Documentation are licensed to the U.S. Government end users (a) only as Commercial Items and (b) with only those rights as are granted to all other end users pursuant to the terms and conditions herein.
Lexmark C950de · August 2015

Lexmark, Lexmark with diamond design, MarkNet, and MarkVision are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.
PrintCryption is a trademark of Lexmark International, Inc.
Mac and the Mac logo are trademarks of Apple Inc., registered in the U.S. and other countries.
PCL® is a registered trademark of the Hewlett-Packard Company. PCL is Hewlett-Packard Company’s designation of a set of printer commands (language) and functions included in its printer products. This printer is intended to be compatible with the PCL language. This means the printer recognizes PCL commands used in various application programs, and that the printer emulates the functions corresponding to the commands.
The following terms are trademarks or registered trademarks of these companies:

CG Times Based on Times New Roman under license from The Monotype Corporation plc, is a product of Agfa Corporation

Univers Linotype-Hell AG and/or its subsidiaries
All other trademarks are the property of their respective owners.
AirPrint and the AirPrint logo are trademarks of Apple, Inc.
statement
This product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The FCC Class A limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
The manufacturer is not responsible for any radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment.
This product may contain the following modular component(s):
Lexmark regulatory type/model LEX-M01-003; FCC ID: IYLM01003; IC: 2376A-M01003
Lexmark regulatory type/model LEX-M05-001; FCC ID:IYLLEXM05001; IC:2376A-M05001
Lexmark regulatory type/model LEX-M05-002; FCC ID:IYLLEXM05002; IC:2376A-M05002
All licensing notices associated with this product can be viewed from the CD:\LEGAL directory of the installation software CD.
The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.

1-meter average sound pressure, dBA
Values are subject to change. See www.lexmark.com for current values.
The WEEE logo signifies specific recycling programs and procedures for electronic products in countries of the European Union. We encourage the recycling of our products. If you have further questions about recycling options, visit the Lexmark Web site at www.lexmark.com for your local sales office phone number.
This product complies with the India E-Waste (Management and Handling) Rules, 2011, which prohibit use of lead, mercury, hexavalent chromium, polybrominated biphenyls, or polybrominated diphenyl ethers in concentrations exceeding 0.1% by weight and 0.01% by weight for cadmium, except for the exemption set in Schedule II of the Rules.
This symbol identifies static-sensitive parts. Do not touch in the areas near these symbols without first touching the metal frame of the printer.
Printing 53 · Ready 22

Any Lexmark product bearing the ENERGY STAR emblem on the product or on a start-up screen is certified to comply with Environmental Protection Agency (EPA) ENERGY STAR requirements as configured when shipped by Lexmark.
Ambient temperature 10.0 to 33.0°C (50 to 91.4°F)
Shipping and storage temperature ‑40 to 40°C (‑40 to 104°F) and 0 to 35°C (32 to 95°F)
The following table documents the power consumption characteristics of the product.
Mode Description Power consumption (Watts)
Printing The product is generating hard‑copy output from electronic inputs. 680
Copy The product is generating hard‑copy output from hard‑copy original documents.
Scan The product is scanning hard‑copy documents. N/A
Ready The product is waiting for a print job. 95
Sleep Mode The product is in a high‑level energy‑saving mode. 15
Hibernate The product is in a low‑level energy‑saving mode. 1.0
Off The product is plugged into a wall outlet, but the power switch is turned off.
The power consumption levels listed in the previous table represent time-averaged measurements. Instantaneous power draws may be substantially higher than the average.
Values are subject to change. See www.lexmark.com for current values.

This product is designed with an energy-saving mode called Sleep Mode. The Sleep Mode saves energy by lowering power consumption during extended periods of inactivity. The Sleep Mode is automatically engaged after this product is not used for a specified period of time, called the Sleep Mode Timeout.
Factory default Sleep Mode Timeout for this product (in minutes): 5
By using the configuration menus, the Sleep Mode Timeout can be modified between 1 minute and 120 minutes. Setting the Sleep Mode Timeout to a low value reduces energy consumption, but may increase the response time of the product. Setting the Sleep Mode Timeout to a high value maintains a fast response, but uses more energy.
This product is designed with an ultra‑low power operating mode called Hibernate mode. When operating in Hibernate Mode, all other systems and devices are powered down safely.
The Hibernate mode can be entered in any of the following methods:
Factory default Hibernate Timeout for this product in all countries or regions 3 days
The amount of time the printer waits after a job is printed before it enters Hibernate mode can be modified between one hour and one month.
If this product has an off mode which still consumes a small amount of power, then to completely stop product power consumption, disconnect the power supply cord from the wall outlet.
It is sometimes helpful to calculate the total product energy usage. Since power consumption claims are provided in power units of Watts, the power consumption should be multiplied by the time the product spends in each mode in order to calculate energy usage. The total product energy usage is the sum of each mode's energy usage.
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Standard ICES-003.
Cet appareil numérique de classe A est conforme aux exigences de la norme canadienne relative aux équipements pouvant causer des interférences NMB-003.

This product is in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, and 2011/65/EU on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits, and on the restrictions of use of certain hazardous substances in electrical and electronic equipment.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product satisfies the Class A limits of EN 55022 and safety requirements of EN 60950‑1.
This is a product that complies with the emission requirements of EN55022 Class A limits and immunity requirements of EN55024. This product is not intended to be used in residential/domestic environments.
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
This section contains the following regulatory information pertaining to wireless products that contain transmitters, for example, but not limited to, wireless network cards or proximity card readers.
The radiated output power of this device is far below the radio frequency exposure limits of the FCC and other regulatory agencies. A minimum separation of 20 cm (8 inches) must be maintained between the antenna and any persons for this device to satisfy the RF exposure requirements of the FCC and other regulatory agencies.
This device complies with Industry Canada specification RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This device has been designed to operate only with the antenna provided. Use of any other antenna is strictly prohibited per regulations of Industry Canada.
To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.
The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF fields in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada's Web site www.hc-sc.gc.ca/rpb

The term "IC:" before the certification/registration number only signifies that the Industry Canada technical specifications were met.
Cet appareil est conforme à la norme RSS-210 d'Industry Canada. Son fonctionnement est soumis aux deux conditions suivantes :
(1) cet appareil ne doit pas provoquer d'interférences et (2) il doit accepter toute interférence reçue, y compris celles risquant d'altérer son fonctionnement.
Cet appareil a été conçu pour fonctionner uniquement avec l'antenne fournie. L'utilisation de toute autre antenne est strictement interdite par la réglementation d'Industry Canada.
En application des réglementations d'Industry Canada, l'utilisation d'une antenne de gain supérieur est strictement interdite.
Pour empêcher toute interférence radio au service faisant l'objet d'une licence, cet appareil doit être utilisé à l'intérieur et loin des fenêtres afin de garantir une protection optimale.
Si le matériel (ou son antenne d'émission) est installé à l'extérieur, il doit faire l'objet d'une licence.
L'installateur de cet équipement radio doit veiller à ce que l'antenne soit implantée et dirigée de manière à n'émettre aucun champ HF dépassant les limites fixées pour l'ensemble de la population par Santé Canada. Reportez-vous au Code de sécurité 6 que vous pouvez consulter sur le site Web de Santé Canada www.hc- sc.gc.ca/rpb.
Le terme « IC » précédant le numéro de d'accréditation/inscription signifie simplement que le produit est conforme aux spécifications techniques d'Industry Canada.
Products bearing the CE mark are in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, 1999/5/EC, and 2011/65/EU on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits, radio equipment and telecommunications terminal equipment, and on the restrictions of use of certain hazardous substances in electrical and electronic equipment.
Compliance is indicated by the CE marking.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product satisfies the Class A limits of EN 55022 and safety requirements of EN 60950‑1.
Products equipped with 2.4GHz Wireless LAN option are in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, and 1999/5/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits and on radio equipment and telecommunications terminal equipment.

Compliance is indicated by the CE marking.
Operation is allowed in all EU and EFTA countries, but is restricted to indoor use only.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product may be used in the countries indicated in the table below.

AT BE BG CH CY CZ DE DK EE
EL ES FI FR HR HU IE IS IT
LI LT LU LV MT NL NO PL PT
Česky Společnost Lexmark International, Inc. tímto prohlašuje, že výrobek tento výrobek je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Dansk Lexmark International, Inc. erklærer herved, at dette produkt overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch Hiermit erklärt Lexmark International, Inc., dass sich das Gerät dieses Gerät in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Ελληνική ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Η LEXMARK INTERNATIONAL, INC. ΔΗΛΩΝΕΙ ΟΤΙ ΑΥΤΟ ΤΟ ΠΡΟΪΟΝ ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
English Hereby, Lexmark International, Inc., declares that this type of equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Español Por medio de la presente, Lexmark International, Inc. declara que este producto cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Eesti Käesolevaga kinnitab Lexmark International, Inc., et seade see toode vastab direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele muudele asjakohastele sätetele.
Suomi Lexmark International, Inc. vakuuttaa täten, että tämä tuote on direktiivin 1999/5/EY oleellisten vaatimusten ja muiden sitä koskevien direktiivin ehtojen mukainen.
Français Par la présente, Lexmark International, Inc. déclare que l'appareil ce produit est conforme aux exigences fondamentales et autres dispositions pertinentes de la directive 1999/5/CE.
Magyar Alulírott, Lexmark International, Inc. nyilatkozom, hogy a termék megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Íslenska Hér með lýsir Lexmark International, Inc. yfir því að þessi vara er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.
Italiano Con la presente Lexmark International, Inc. dichiara che questo questo prodotto è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.

Latviski Ar šo Lexmark International, Inc. deklarē, ka šis izstrādājums atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių Šiuo Lexmark International, Inc. deklaruoja, kad šis produktas atitinka esminius reikalavimus ir kitas 1999/5/EB direktyvos nuostatas.
Malti Bil-preżenti, Lexmark International, Inc., jiddikjara li dan il-prodott huwa konformi mal-ħtiġijiet essenzjali u ma dispożizzjonijiet oħrajn relevanti li jinsabu fid-Direttiva 1999/5/KE.
Nederlands Hierbij verklaart Lexmark International, Inc. dat het toestel dit product in overeenstemming is met de
essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Norsk Lexmark International, Inc. erklærer herved at dette produktet er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.
Polski Niniejszym Lexmark International, Inc. oświadcza, że niniejszy produkt jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português A Lexmark International Inc. declara que este este produto está conforme com os requisitos essenciais e outras disposições da Diretiva 1999/5/CE.
Slovensky Lexmark International, Inc. týmto vyhlasuje, že tento produkt spĺňa základné požiadavky a všetky príslušné ustanovenia smernice 1999/5/ES.
Slovensko Lexmark International, Inc. izjavlja, da je ta izdelek v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.
Svenska Härmed intygar Lexmark International, Inc. att denna produkt står i överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
STATEMENT OF LIMITED WARRANTY FOR LEXMARK LASER PRINTERS, LEXMARK LED PRINTERS, AND LEXMARK MULTIFUNCTION LASER
This limited warranty applies to the United States and Canada. For customers outside the U.S., refer to the country-specific warranty information that came with your product.
This limited warranty applies to this product only if it was originally purchased for your use, and not for resale, from Lexmark or a Lexmark Remarketer, referred to in this statement as “Remarketer.”
Lexmark warrants that this product:
—Is manufactured from new parts, or new and serviceable used parts, which perform like new parts
—Is, during normal use, free from defects in material and workmanship
If this product does not function as warranted during the warranty period, contact a Remarketer or Lexmark for repair or replacement (at Lexmark's option).
If this product is a feature or option, this statement applies only when that feature or option is used with the product for which it was intended. To obtain warranty service, you may be required to present the feature or option with the product.

If you transfer this product to another user, warranty service under the terms of this statement is available to that user for the remainder of the warranty period. You should transfer proof of original purchase and this statement to that user.
The warranty period starts on the date of original purchase as shown on the purchase receipt and ends 12 months later provided that the warranty period for any supplies and for any maintenance items included with the printer shall end earlier if it, or its original contents, are substantially used up, depleted, or consumed. Fuser Units, Transfer/Transport Units, Paper Feed items, if any, and any other items for which a Maintenance Kit is available are substantially consumed when the printer displays a “Life Warning” or “Scheduled Maintenance” message for such item.
To obtain warranty service you may be required to present proof of original purchase. You may be required to deliver your product to the Remarketer or Lexmark, or ship it prepaid and suitably packaged to a Lexmark designated location. You are responsible for loss of, or damage to, a product in transit to the Remarketer or the Lexmark designated location.
When warranty service involves the exchange of a product or part, the item replaced becomes the property of the Remarketer or Lexmark. The replacement may be a new or repaired item.
The replacement item assumes the remaining warranty period of the original product.
Replacement is not available to you if the product you present for exchange is defaced, altered, in need of a repair not included in warranty service, damaged beyond repair, or if the product is not free of all legal obligations, restrictions, liens, and encumbrances.
As part of your warranty service and/or replacement, Lexmark may update the firmware in your printer to the latest version. Firmware updates may modify printer settings and cause counterfeit and/or unauthorized products, supplies, parts, materials (such as toners and inks), software, or interfaces to stop working. Authorized use of genuine Lexmark products will not be impacted.
Before you present this product for warranty service, remove all print cartridges, programs, data, and removable storage media (unless directed otherwise by Lexmark).
For further explanation of your warranty alternatives and the nearest Lexmark authorized servicer in your area contact Lexmark on the World Wide Web.
Remote technical support is provided for this product throughout its warranty period. For products no longer covered by a Lexmark warranty, technical support may not be available or only be available for a fee.
Lexmark does not warrant uninterrupted or error-free operation of any product or the durability or longevity of prints produced by any product.
Warranty service does not include repair of failures caused by:
—Modification or unauthorized attachments
—Accidents, misuse, abuse or use inconsistent with Lexmark user’s guides, manuals, instructions or guidance
—Unsuitable physical or operating environment
—Maintenance by anyone other than Lexmark or a Lexmark authorized servicer
—Operation of a product beyond the limit of its duty cycle
—Use of printing media outside of Lexmark specifications

—Refurbishment, repair, refilling or remanufacture by a third party of products, supplies or parts
—Products, supplies, parts, materials (such as toners and inks), software, or interfaces not furnished by Lexmark
TO THE EXTENT PERMITTED BY APPLICABLE LAW, NEITHER LEXMARK NOR ITS THIRD PARTY SUPPLIERS OR REMARKETERS MAKE ANY OTHER WARRANTY OR CONDITION OF ANY KIND, WHETHER EXPRESS OR IMPLIED, WITH RESPECT TO THIS PRODUCT, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND SATISFACTORY QUALITY. ANY WARRANTIES THAT MAY NOT BE DISCLAIMED UNDER APPLICABLE LAW ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. NO WARRANTIES, EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD. ALL INFORMATION, SPECIFICATIONS, PRICES, AND SERVICES ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE.
Your sole remedy under this limited warranty is set forth in this document. For any claim concerning performance or nonperformance of Lexmark or a Remarketer for this product under this limited warranty, you may recover actual damages up to the limit set forth in the following paragraph.
Lexmark's liability for actual damages from any cause whatsoever will be limited to the amount you paid for the product that caused the damages. This limitation of liability will not apply to claims by you for bodily injury or damage to real property or tangible personal property for which Lexmark is legally liable. IN NO EVENT WILL LEXMARK BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, INCIDENTAL DAMAGE, OR OTHER ECONOMIC OR CONSEQUENTIAL DAMAGES. This is true even if you advise Lexmark or a Remarketer of the possibility of such damages. Lexmark is not liable for any claim by you based on a third party claim.
This limitation of remedies also applies to claims against any Suppliers and Remarketers of Lexmark. Lexmark's and its Suppliers' and Remarketers' limitations of remedies are not cumulative. Such Suppliers and Remarketers are intended beneficiaries of this limitation.
Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or limitation of incidental or consequential damages, so the limitations or exclusions contained above may not apply to you.
This limited warranty gives you specific legal rights. You may also have other rights that vary from state to state.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Elliptic Curve Cryptography (ECC) Cipher Suites for Transport Layer Security (TLS) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for TLS Elliptic Curve Cipher Suites with SHA-256/382 and AES Galois Counter Mode (GCM) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for TLS Suite B Profile for Transport Layer Security (TLS) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Addition of the Camellia Cipher Suites to Transport Layer Security (TLS) implemented in the product or service.

The use of certain patents in this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for AES-CCM ECC Cipher Suites for TLS implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for IKE and IKEv2 Authentication Using the Eliptic Curve Digital Signature Algorithm (ECDSA) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Suite B Cryptographic Suites for IPSec implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Algorithms for Internet Key Exchange version 1 (IKEv1) implemented in the product or service.








configuration information 43 installation, using Macintosh 46 installation, using Windows 44 wireless network setup
in Windows 44 wireless printer setup
Index 261 · wireless network · in Macintosh 46
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.