EN
Laserliner logo
Official user manual

Laserliner MultiMeter

60 pages·4.9 MB·Measuring instruments·PDF·ENITJA
Laserliner MultiMeter
Table of Contents 10 sections Function / Application · Symbols · Safety instructions · Additional information on use · … ShowHide
Page 1 of the Laserliner MultiMeter user manual — Safety instructions
Page 1 · click to enlarge
Page 1

Read the operating instructions and the enclosed brochure “Guarantee and additional notices“ completely. Follow the instructions they contain. Safely keep these documents for future reference. !

Function / Application

Multimeter for taking measurements in the range of overvoltage category CAT III up to max. 300 V. The multimeter can be used to measure DC and AC voltages, direct current, battery charge status, resistance and check diodes within the specified ranges.

Symbols

Hazardous electrical voltage warning: Unprotected live components inside the device housing may pose a risk of electric shock.

Protection class II: The test device has reinforced or double insulation.

Overvoltage category III: Equipment in fixed installations and for applications where specific requirements with regard to the reliability and availability of equipment have to be met, e.g. circuit-breakers in fixed installations and devices used in industrial applications which are permanently connected to the fixed installation.

Safety instructions

  • The device must only be used in accordance with its intended purpose and within the scope of the specifications. Modifications or changes to the device are not permitted, this will otherwise invalidate the approval and safety specifications.
  • In overvoltage category III (CAT III), the voltage between the test device and earth must not exceed 300 V.
  • The lowest overvoltage category (CAT), rated voltage and rated current apply when using the device together with the measuring equipment.
  • Do not expose the device to mechanical stress, extreme temperatures or significant vibration.
Page 2 of the Laserliner MultiMeter user manual — Function / Application
Page 2 · click to enlarge
Page 2
  • If you are working with voltages higher than 25 V AC / 60 V DC, exercise extreme caution. Touching the electrical conductors at such voltages poses a risk of life-threatening electric shocks.
  • If the device comes into contact with moisture or other conductiveresidue, work must not be carried out under voltage. At and above voltages of 25 V AC / 60 V DC, the presence of moisture creates the risk of life-threatening electric shocks. Clean and dry the device before use. When using the device outdoors, make sure that the weather conditions are appropriate and/or that suitable protection measures are taken.
  • Before taking any measurements, make sure that both the area to be tested (e.g. a line), the test device and the accessories used (e.g. connection cable) are in proper working order. Test the device by connecting it to known voltage sources (e.g. a 230 V socket in the case of AC testing or a car battery in the case of DC testing). The device must no longer be used if one or more of its functions fail or the battery charge is weak.
  • The device must be isolated from all current sources before opening the cover to change the battery(ies) or fuse(s). Do not switch on the device with the cover open.
  • Observe the safety precautions of local and national authorities relating to the correct use of the device and any prescribed safety equipment (e.g. electrician‘s safety gloves).
  • If you have to take hold of the measuring spikes, do so by the grip sections only. Do not touch the measuring contacts whilst the measurement is being taken.
  • Make sure that you always select the correct connections and rotary switch position with the correct measuring range for the measurement to be carried out.
  • Disconnect the power supply to the electrical circuit before measuring or checking the diodes, resistance or battery charge. Make sure that all high-voltage capacitors are discharged. To check, remove the measuring leads of the device from the test piece before changing the mode.
  • When connecting to a voltage, always connect the black measuring lead first before the red lead. Follow the reverse procedure when disconnecting.
  • Only the original measuring leads may be used. Their voltage, category and ampere rated powers must match those of the measuring device.
Page 3 of the Laserliner MultiMeter user manual — Additional information on use
Page 3 · click to enlarge
Page 3
  • If possible, do not work alone. Carry out measurements in the vicinity of hazardous electrical installations only under the guidance of a qualified electrician.
  • The measuring tools and accessories are not toys. Keep out of reach of children.

Additional information on use

Observe the technical safety regulations for working on electrical systems, especially: 1. Safely isolating from power supply, 2. Securing to prevent system being switched on again, 3. Checking zero potential, two-pole, 4. Earthing and short- circuiting, 5. Securing and covering adjacent live components.

Laserliner MultiMeter — Additional information on use diagram (page 3)
Fig. 1 · Additional information on use
Page 4 of the Laserliner MultiMeter user manual — Maximum limit values
Page 4 · click to enlarge
Page 4

Maximum limit values

Laserliner MultiMeter — Maximum limit values diagram (page 4)
Fig. 2 · Maximum limit values

V DC / V AC 300 V DC, 300 V AC

A DC 10 A DC (> 2 A max. 10 seconds every 15 minutes)

To replace the battery or fuses, first disconnect the test prods from their voltage source and then from the device. Undo all the screws at the rear of the device and replace the battery or replace the defective fuse by a fuse of the same type and rating. Do not touch the green pc-board. Also make sure it is kept clean. Close the housing and carefully screw the meter back together. Do not switch on the device with the cover open.

Laserliner MultiMeter — Maximum limit values diagram (page 4)
Fig. 3 · Maximum limit values

1 F 250 mA / 300 V (Ø 5 mm x 20 mm)

2 F 10 A / 300 V (Ø 5 mm x 20 mm)

3 1 x 9 V NEDA 1604 / IEC 6F22

Page 5 of the Laserliner MultiMeter user manual — Voltage measurement DC
Page 5 · click to enlarge
Page 5
Laserliner MultiMeter — Voltage measurement DC diagram (page 5)
Fig. 4 · Voltage measurement DC

The black test prod (–) must always be connected to the "COM socket". When taking current measurements > 200 mA the red test prod (+) must be connected to the "10 A socket". For all other measuring functions, the red test prod must be connected to the "VmAΩ -socket".

Laserliner MultiMeter — Voltage measurement DC diagram (page 5)
Fig. 5 · Voltage measurement DC

Before measuring, make sure that the test prods are connected correctly as the built-in fuse could otherwise trip and damage the measuring circuit. !

If the value of the measured variable is not known in advance, set the rotary switch to the highest measuring range or use the 10 A connection with the 10 A measuring range to measure current. Then reduce the measuring range step by step until a satisfactory resolution is achieved.

Voltage measurement DC

To measure voltage, set the rotary switch to the " " position with the corresponding measuring range (200 mV - 300 V).

Then connect the measuring contacts to the object to be tested. The measured value acquired and the polarity appear on the display.

Laserliner MultiMeter — Voltage measurement DC diagram (page 5)
Fig. 6 · Voltage measurement DC
Page 6 of the Laserliner MultiMeter user manual — Voltage measurement DC
Page 6 · click to enlarge
Page 6
Laserliner MultiMeter — Voltage measurement DC diagram (page 6)
Fig. 7 · Voltage measurement DC

To measure voltage, set the rotary switch to the " " position with the corresponding measuring range (200 V / 300 V).

Then connect the measuring contacts to the object to be tested. The measured value acquired appears on the display.

Laserliner MultiMeter — Voltage measurement DC diagram (page 6)
Fig. 8 · Voltage measurement DC

To measure current, set the rotary switch to the " " position with the corresponding measuring range (2,000 μA - 10 A). Ensure that the test prods are connected correctly.

2,000 μA - 200 mA = VmAΩ -socket > 200 mA - 10 A = 10 A-socket

Disconnect the circuit before connecting the meter. Then connect the measuring contacts to the object to be tested.

Laserliner MultiMeter — Voltage measurement DC diagram (page 6)
Fig. 9 · Voltage measurement DC

The measured value acquired and the polarity appear on the display. Disconnect the circuit again before disconnecting the meter.

Page 7 of the Laserliner MultiMeter user manual — Voltage measurement DC
Page 7 · click to enlarge
Page 7
Laserliner MultiMeter — Voltage measurement DC diagram (page 7)
Fig. 10 · Voltage measurement DC

Do not measure currents above 2 A for longer than 10 seconds within 15 minutes. This could damage the device or the test prods.

Current above 200 mA must not be measured in the μA / mA range and currents above 10 A must not be measured in the A range. Otherwise the corresponding built-in fuse will trip (F 250 mA / 300 V, F 10 A / 300 V, Ø 5 mm x 20 mm). !

To measure the battery charge status, set the rotary switch to the "BAT." position with the corresponding measuring range.

1.5 V = 1.5 V round cells / AA, AAA, C, D 1.2 V round cells (NiMH) / AA, AAA, C, D

9 V = 9.0 V flat cells / E-block

8.4 V flat cells (NiMH) / E-block

Then connect the measuring contacts to the battery.

Laserliner MultiMeter — Voltage measurement DC diagram (page 7)
Fig. 11 · Voltage measurement DC

The battery voltage is shown on the display. You can read off the battery charge status from the following scale.

Good: battery fully charged Weak: battery is weak and will soon need replacing Replace: battery is flat and should be replaced

Example BatteryAlkaline 9 V Measured voltage: 6.2 V Battery charge status: weak
Page 8 of the Laserliner MultiMeter user manual — Voltage measurement DC
Page 8 · click to enlarge
Page 8
Laserliner MultiMeter — Voltage measurement DC diagram (page 8)
Fig. 12 · Voltage measurement DC

1500 1400 1300 1200 1100 1000 900 800 700

9.0 8.3 7.6 6.9 6.2 5.5 4.8 4.1 3.4

1200 1130 1060 990 920 850 780 710 640

8.4 7.9 7.4 6.9 6.4 5.9 5.4 4.9 4.4

To test the diode, turn the rotary switch to position " ".

Then connect the measuring contacts to the diode. The measured value acquired for the forward voltage appears on the display.

If "1" appears on the display instead of a measured value, the diode has either been tested in the reverse direction or is faulty. If 0.0 V is measured, the diode is faulty or a short-circuit has occurred.

Page 9 of the Laserliner MultiMeter user manual — = 17.28 kΩ
Page 9 · click to enlarge
Page 9
Laserliner MultiMeter — = 17.28 kΩ diagram (page 9)
Fig. 13 · = 17.28 kΩ

To measure resistance, set the rotary switch to the "Ω" position with the corresponding measuring range (200 Ω - 2,000 kΩ).

Then connect the measuring contacts to the object to be tested. The measured value acquired appears on the display.

If "1" appears on the display instead of a measured value, either the measuring range has been exceeded or the measuring circuit is not closed or has been interrupted.

= 17.28 kΩ

Resistances can only be measured correctly in isolation; therefore, the components might need to be disconnected from the remainder of the circuit.

When measuring resistance, to avoid the risk of the results of a measurement being distorted, there must be no traces of dirt, oil, solder spray or other contamination on the test prods. !

Page 10 of the Laserliner MultiMeter user manual — Technical data
Page 10 · click to enlarge
Page 10

Technical data

Max. input voltage 300 V AC / DC

200 mV ± (0.5% rdg + 5 digits) 2,000 mV ± (0.8% rdg + 5 digits) 20 V 200 V 300 V ± (1.0% rdg + 5 digits)

AC voltage 200 V ± (1.2% rdg + 10 digits) 300 V

2,000 μA ± (1.0% rdg + 5 digits) 20 mA 200 mA ± (1.2% rdg + 5 digits) 10 A ± (2.0% rdg + 5 digits)

1.5 V round cells / AA, AAA, C, D 1.2 V round cells (NiMH) / AA, AAA, C, D 9.0 V flat cells / E-block 8.4 V flat cells (NiMH) / E-block

Diode test / resistance Test voltage max. 3.2 V

200 Ω ± (1.0% rdg + 5 digits) 2,000 Ω ± (0.8% rdg + 5 digits) 20 kΩ 200 kΩ 2,000 kΩ ± (1.2% rdg + 5 digits) Input sensitivity 1 MΩ (V DC) / 500 kΩ (V AC) Polarity Sign for negative polarity LCD (3 1/2 segments, 1,999 digits)

Fuse F 250 mA / 300 V, F 10 A / 300 V, (Ø 5 x 20 mm) Protection class II, double insulation Overvoltage CAT III - 300 V Pollution degree 2 Degree of protection IP 20 Max. rel. humidity < 75% rH non-condensing Operating temperature 0°C…40°C Storage temperature -10°C…50°C Power supply 1 x 9 V battery (NEDA 1604, IEC 6F22) Dimensions 77 x 139 x 28 mm Weight (incl. battery) 204 g

Test standards EN61010-1, EN61010-2-030, EN61010-2-033, EN61326-1, EN61326-2-2

Subject to technical alterations 12.15

Show 5 more labels / short text on this page
Function Range Accuracy · DC voltage · DC current · Batteries · Resistance
Page 11 of the Laserliner MultiMeter user manual — EU directives and disposal
Page 11 · click to enlarge
Page 11

Information on maintenance and care

Clean all components with a damp cloth and do not use cleaning agents, scouring agents and solvents. Remove the battery(ies) before storing for longer periods. Store the device in a clean and dry place.

EU directives and disposal

This device complies with all necessary standards for the free movement of goods within the EU.

This product is an electric device and must be collected separately for disposal according to the European Directive on waste electrical and electronic equipment.

Further safety and supplementary notices at: www.laserliner.com/info

Ask about the Laserliner MultiMeter

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Laserliner MultiMeter

Be the first to ask — other owners or our team will answer.

Original document

Laserliner MultiMeter manual PDF

60 pages·4.9 MB·Measuring instruments·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…