

Read the operating instructions and the enclosed brochure „Guarantee and additional notices“ completely. Follow the instructions they contain. This document must be kept in a safe place and passed on together with the device. !
Function / Application This material moisture device detects and evaluates the material moisture content of wood and building materials by way of electric resistance measure- ment. The displayed value is material moisture in % with respect to dry mass. Example:ƁL@SDQH@KLNHRSTQDENQƁJFNEVDSVNNC ƁFV@SDQ

ON/OFF Mode selection: Wood, building materials, Index mode, Test mode


Open the battery compartment and insert batteries according to the symbols. Be sure to pay attention to polarity.
GmbH & Co KG nnerfeld 2 757 Arnsberg, Germany : +49 2932 638-300, Fax: -333 ww.laserliner.com
After switching on the device, the ambient temperature is displayed for 1 second.



Display illumination °C / °F switch-over

Just which wood types are grouped under A, B and C can be found in the table in Section 10.
Manual temperature compensation · Programmable wet/dry indicator


Just which building materials are grouped under 01 to 08 can be found in the table in Section 11.
Be sure neither supply lines (electric lines, water pipes, etc) nor a metal subsur- face is present at the location to be measured. Insert the electrodes as far into the material as possible but never use excessive or sudden impact force as this could damage the device. Always pull the device out of the material with left/right twisting motion. Perform several comparative measurements at different locations to minimise measurement error. The sharply pointed electrodes present an injury hazard. Always put the safety cap on the device when it is not in use or being transported.
The location to be measured should be un- treated, free of knots, dirt and resin. Measure- ments should not be made on the end faces of wood because these areas dry particularly quickly such that they produce incorrect measurement results. Perform multiple comparative measurements. Wait until the % symbol stops blinking and remains constantly lighted. Only then are measurement values stable.



Be aware that walls (or surfaces) with differing material structures, or even variations in material composition, can cause measurement QDRTKSRSNADE@KRHÖDC Perform multiple comparative measurements. Wait until the % symbol stops blinking and remains constantly lighted. Only then are measure- ment values stable.
Material characteristics The material characteristics available for selection in the measuring device are listed in the tables below. The different types of wood are divided into Groups A ... C. Please set the measuring device for the respective group in which the type of wood to be measured is found (see Step 5). A similar setting must also be made for measurements performed on building materials (see Step 6). Building materials are divided into groups 01 through 08.



01 Anhydrite screed (AE, AFE) / 0 … 29.5%
06 Limestone, bulk density 1.9 / 0.5 … 18.7%
08 Cement screed without additive / 1.0 … 4.5%


3GDVDSCQXHMCHB@SNQB@MADOQNFQ@LLDCSNSGD@KQD@CXOQDCDÖMDCU@KTDR especially for index mode. This produces a new setting for the „wet“ and „dry“ threshold value (see arrows).

Continued on next page

09 10 11 12 13 14 15 16 17 18 19 20
1000 5,4 11,6 3,4 24,1 9,2 19,8 39,5 10,5 18,2 50,1 70,7 33,1 994 5,3 10,8 3,3 22,3 8,6 19,2 35,4 9,9 18,0 49,1 69,0 32,4 989 5,3 10,0 3,2 20,5 7,9 18,6 31,2 9,3 17,8 48,1 67,0 31,7 927 5,0 8,0 2,8 17,1 6,5 17,2 23,8 8,2 17,2 45,6 62,7 30,3 887 4,9 6,8 2,6 14,9 5,7 16,3 20,0 6,5 16,8 43,9 59,8 29,3 865 4,8 6,0 2,5 13,6 5,2 15,1 17,5 6,9 16,5 42,7 57,9 28,8 830 4,7 5,4 2,4 12,4 4,8 14,0 15,6 6,5 16,2 41,6 56,0 28,1 768 4,6 4,7 2,1 10,6 4,1 13,0 12,4 5,7 15,7 39,5 51,7 26,6 710 4,4 4,0 1,9 8,6 3,4 12,0 9,5 5,0 15,2 37,4 47,7 25,1 644 4,2 3,5 1,7 7,1 2,7 11,3 7,0 4,3 14,7 35,2 43,6 23,6 589 4,1 3,4 1,6 6,2 2,4 11,1 5,9 3,9 14,4 33,5 40,3 22,3 566 4,0 3,4 1,6 6,0 2,3 10,2 5,6 3,8 14,3 33,1 39,5 22,0 491 3,9 3,2 1,4 4,9 1,9 9,7 4,1 3,2 13,8 30,8 35,2 20,2 448 3,8 3,1 1,3 4,4 1,7 9,2 3,5 3,0 13,6 29,7 33,4 19,4 403 3,7 3,0 1,2 3,8 1,5 8,8 2,9 2,7 13,2 27,8 30,8 17,7 375 3,6 3,0 1,1 3,4 1,3 8,4 2,4 2,5 12,9 26,4 28,9 16,6 345 3,5 2,9 1,1 3,0 1,1 8,2 2,0 2,2 12,7 24,8 26,9 15,3 327 3,5 2,9 1,0 2,8 1,1 8,0 1,8 2,2 12,5 24,0 25,8 14,8 306 3,5 2,8 1,0 2,7 1,0 7,9 1,7 2,1 12,4 23,4 24,9 14,4 295 3,5 2,8 1,0 2,6 1,0 7,8 1,7 2,0 12,4 23,0 24,4 14,2 278 3,4 2,8 1,0 2,5 1,0 7,7 1,6 2,0 12,3 22,3 23,4 13,8 269 3,4 2,8 1,0 2,4 0,9 7,6 1,5 1,9 12,2 21,9 22,8 13,6 265 3,4 2,8 1,0 2,3 0,9 7,5 1,5 1,9 12,2 21,6 22,3 13,4 260 3,4 2,8 1,0 2,3 0,9 7,4 1,4 1,8 12,1 21,1 21,7 13,2 248 3,4 2,8 0,9 2,1 0,8 7,2 1,3 1,8 12,0 20,5 20,7 12,7 229 3,3 2,7 0,9 2,0 0,8 7,0 1,2 1,7 11,9 19,7 19,7 12,4 209 3,3 2,7 0,8 1,9 0,7 6,8 1,1 1,6 11,8 17,7 17,2 11,2 189 3,2 2,7 0,8 1,8 0,7 6,6 1,0 1,6 11,6 16,0 15,2 10,2 180 3,2 2,6 0,8 1,7 0,6 6,6 0,9 1,5 11,5 15,1 14,2 9,7 174 3,2 2,6 0,8 1,7 0,6 6,6 0,9 1,5 11,5 14,9 13,9 9,6 164 3,2 2,6 0,7 1,6 0,6 6,5 0,8 1,4 11,4 13,9 12,9 9,0 150 3,1 2,6 0,7 1,5 0,5 6,3 0,8 1,4 11,3 12,5 11,6 8,3 112 3,0 2,5 0,7 1,3 0,5 6,0 0,6 1,2 11,0 9,8 8,0 6,7 105 3,0 2,5 0,7 1,3 0,5 5,9 0,6 1,2 11,0 9,2 7,2 6,4 96 3,0 2,5 0,7 1,2 0,4 5,9 0,6 1,2 10,9 8,6 6,2 6,0 88 3,0 2,5 0,6 1,2 0,4 5,8 0,6 1,2 10,9 8,0 5,4 5,7 80 2,9 2,5 0,6 1,2 0,4 5,8 0,5 1,1 10,7 7,4 4,5 5,4 71 2,9 2,5 0,6 1,2 0,4 5,7 0,5 1,1 10,7 6,6 3,3 4,9 46 2,9 2,5 0,6 1,1 0,4 5,7 0,5 1,1 10,7 5,9 2,3 4,2
All values in material moisture %
Index mode value

21 22 23 24 25 26 27 28 29 30 31
1000 40,2 55,6 34,6 75,8 28,8 51,9 97,3 OL 103,8 110,3 16,3 994 39,0 54,1 32,8 67,9 26,1 50,7 94,9 OL 101,3 107,6 15,6 989 37,8 52,4 31,3 59,1 23,2 49,6 92,3 OL 98,7 105,0 13,6 927 35,1 48,9 27,9 43,5 18,1 46,7 86,7 OL 92,5 98,5 11,0 887 33,1 46,2 25,8 35,3 15,2 44,6 82,5 OL 88,3 93,9 9,8 865 31,8 44,5 24,4 29,8 13,4 43,2 97,9 OL 85,4 91,0 9,2 830 30,3 42,1 23,1 25,9 12,1 41,8 77,0 OL 82,5 87,7 8,8 768 27,7 36,5 20,7 20,1 9,8 38,9 71,1 OL 76,0 81,0 8,2 710 25,0 30,9 18,5 14,5 7,7 35,9 65,3 OL 70,0 74,5 7,6 644 22,2 25,4 16,3 10,0 5,8 33,1 59,0 132,7 63,2 67,5 7,1 589 19,9 20,9 14,9 8,1 4,9 30,8 53,5 112,8 57,3 61,2 6,4 566 19,4 19,9 14,6 7,7 4,7 30,3 52,2 108,7 56,0 59,9 6,0 491 16,5 14,1 12,8 5,3 3,6 27,2 45,2 83,3 48,7 51,9 5,3 448 15,1 11,5 12,0 4,2 3,1 25,8 42,1 71,8 45,3 48,4 4,8 403 12,7 9,2 11,0 3,4 2,6 23,4 39,0 55,3 40,5 43,2 4,2 375 11,2 7,6 10,3 2,9 2,3 21,7 37,0 49,6 37,2 39,9 4,0 345 9,5 5,7 9,4 2,2 1,9 19,9 34,6 43,3 33,6 36,0 3,7 327 8,6 5,1 9,1 2,0 1,7 18,9 33,3 41,1 31,4 33,6 3,4 306 7,9 4,9 8,9 1,9 1,6 18,2 32,0 39,7 29,5 31,7 3,1 295 7,4 4,7 8,7 1,8 1,6 17,8 31,3 38,9 28,3 30,5 3,0 278 6,7 4,4 8,5 1,7 1,5 17,0 30,2 37,4 26,7 28,7 2,8 269 6,3 4,2 8,3 1,6 1,4 16,6 29,7 36,5 26,2 28,1 2,5 265 5,9 4,1 8,2 1,5 1,4 16,2 29,4 35,8 25,6 27,7 2,4 260 5,5 3,9 8,0 1,5 1,3 15,8 28,9 35,0 25,2 27,1 2,3 248 4,7 3,5 7,7 1,3 1,2 14,9 28,1 33,4 24,2 26,1 2,2 229 4,0 3,2 7,5 1,2 1,1 14,2 27,3 31,9 23,2 25,0 1,9 209 2,9 2,7 7,1 1,1 1,0 13,0 24,3 28,4 20,8 22,4 1,6 189 1,9 2,4 6,8 0,9 1,0 11,9 21,6 25,3 18,7 20,2 1,3 180 1,3 2,2 6,7 0,8 0,9 11,3 20,3 23,6 17,7 19,2 1,2 174 1,1 2,2 6,6 0,8 0,9 11,1 19,9 23,2 17,4 19,8 1,1 164 0,8 2,1 6,4 0,8 0,8 10,4 18,3 21,3 16,5 17,9 0,8 150 0,3 1,9 6,2 0,7 0,8 9,5 16,1 18,8 15,1 16,5 0,5 112 0,0 1,8 5,7 0,6 0,6 7,6 11,5 11,7 11,2 12,3 0,0 105 0,0 1,8 5,6 0,6 0,6 7,2 10,9 10,1 10,3 11,4 0,0 96 0,0 1,7 5,5 0,5 0,6 6,7 10,2 8,3 9,2 10,2 0,0 88 0,0 1,7 5,4 0,5 0,6 6,3 9,7 6,8 8,4 9,3 0,0 80 0,0 1,7 5,3 0,5 0,5 5,8 9,1 5,8 7,3 8,2 0,0 71 0,0 1,7 5,3 0,4 0,5 5,3 8,5 4,9 6,2 7,0 0,0 46 0,0 1,7 5,2 0,4 0,5 4,8 8,3 4,5 5,2 5,8 0,0
OL = Outside measuring range GB
Index mode value · dry moist wet


The relative material moisture of wood is dependent on temperature. The device automatically compensates for different wood temperatures by measuring the ambient temperature and using it for the internal calculation.
To increase measuring accuracy, however, the measuring device also offers an option for setting the temperature manually (see Step 16b). This value is not stored and must be set again each time the device is switched on.
AUTO: Display illumination switches off during periods of inactivity and
switches on again automatically for measurement procedures. ON: Display illumination remains on permanently. OFF: Display illumination remains off permanently.
The setting is stored and remains in effect until it is changed manually.



The units of measure for ambient temperature and material compensation can be set to either °C or °F. The setting is stored and remains in effect until it is changed manually.

Functional and operational safety is only warranted when the instru- ment is operated within the specified climatic conditions and is only used for those purposes for which it is designed. The assessment of measurement results and actions taken as a consequence lie in the user‘s scope of responsibility, depending on the given type of work. !
Technical revisions reserved. 06.16
3 wood groups 8 building materials Index mode for 23 additional building materials, Test mode
wood: 0 - 30% / ± 1%
Permissible operating temperature 0 °C…40 °C
Permissible storage temperature -10 °C…60 °C Permissible max. relative humidity 85% Power supply Batteries, 4x 1.5 V type AAA
Dimensions (W x H x D) 58 mm x 155 mm x 38 mm
EU directives and disposal This device complies with all necessary standards for the free movement of goods within the EU.
This product is an electric device and must be collected separately for disposal according to the European Directive on waste electrical and electronic equipment.


Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.