EN
Laserliner logo
Official user manual

Laserliner DampMaster

84 pages·4.4 MB·Measuring instruments·PDF·EN
Laserliner DampMaster
Table of Contents 31 sections Measuring material moisture · Mineral building materials Wood · DE · Wood · … ShowHide
Page 1 of the Laserliner DampMaster user manual
Page 1 · click to enlarge
Page 1
Laserliner DampMaster diagram (page 1)
Fig. 1

Auto switch-off after 3 minutes. When the device is turned on, the display will show the ambient temperature for 3 seconds.

Switch on device Switch-over to building materials, Index mode, Test mode

Page 2 of the Laserliner DampMaster user manual
Page 2 · click to enlarge
Page 2

Function/application: This material moisture device detects and evaluates the material moisture content of wood and building materials by way of electric resistance measurement. The displayed value is material moisture in % with respect to dry mass. Example: 100 % material moisture for 1 kg of wet wood = 500 g water.

Laserliner DampMaster diagram (page 2)
Fig. 2

Test mode Index mode Building materials: 01, 02, 03, 04 Wood groups: A, B, C

Laserliner DampMaster diagram (page 2)
Fig. 3

°C / °F switch-over Display illumination Programmable wet/dry indicator Manual temperature compensation

Laserliner DampMaster diagram (page 2)
Fig. 4

Just which wood types are grouped under A, B and C can be found in the table in Section 10.

Page 3 of the Laserliner DampMaster user manual — DE
Page 3 · click to enlarge
Page 3
Laserliner DampMaster — Measuring material moisture diagram (page 3)
Fig. 5 · Measuring material moisture

Just which building materials are grouped under 01 to 04 can be found in the table in Section 11.

Measuring material moisture

Be sure neither supply lines (electric lines, water pipes, etc) nor a metal subsurface is present at the location to be measured. Insert the electrodes as far into the material as possible but never use excessive or sudden impact force as this could damage the device. Always pull the device out of the material with left/right twisting motion. Perform several comparative measurements at different locations to minimise measurement error. The sharply pointed electrodes present an injury hazard. Always put the safety cap on the device when it is not in use or being transported.

Mineral building materials Wood

Laserliner DampMaster — Mineral building materials Wood diagram (page 3)
Fig. 6 · Mineral building materials Wood
Laserliner DampMaster — Mineral building materials Wood diagram (page 3)
Fig. 7 · Mineral building materials Wood
Laserliner DampMaster — Mineral building materials Wood diagram (page 3)
Fig. 8 · Mineral building materials Wood

The location to be measured should be untreated, free of knots, dirt and resin. Measurements should not be made on the end faces of wood because these areas dry particularly quickly such that they produce incorrect measurement results. Perform multiple comparative measurements. Wait until the % symbol stops blinking and remains constantly lighted. Only then are measurement values stable.

Be aware that walls (or surfaces) with differing material structures, or even variations in material composition, can cause measurement results to be falsiÖ ed. Perform multiple comparative measurements. Wait until the % symbol stops blinking and remains constantly lighted. Only then are measurement values stable.

DE

Page 4 of the Laserliner DampMaster user manual — Building materials
Page 4 · click to enlarge
Page 4

Material characteristics The material characteristics available for selection in the measuring device are listed in the tables below. The different types of wood are divided into Groups A ... C. Please set the measuring device for the respective group in which the type of wood to be measured is found (see Step 5). A similar setting must also be made for measurements performed on building materials (see Step 6). Building materials are divided into groups 01 through 04.

Wood

A B C

Abachi Abachi Abura Afzelia Pear wood Black Afara Parana pine Beech Dabema Ebony Oak, red Oak, white Ash Yellowheart Ash - American Ash - Japanese Hickory - silver poplar Hickory - swap Ilomba Ipe Iroko Small-leaved lime Small-leaved lime - American Mockernut hickory Niangon Niové Okoumé Rosewood Rio rosewood Common beech Red oak Teak Willow White oak Cedar Cypress - C. Lusit Board

mahogany Pine Cherry wood Kosipo Larch Limba Mahogany Cherry mahogany Melêze Poplar (all) Plum wood Pine Red sandalwood Elm Maritime pine English oak Durmast oak Tola Tola - branca Walnut Western red Cedar White maple White birch White beech White poplar Swiss pine Common aspen Damson wood Cypress, real Fibre board Wood fibre insulating board Wood fibre hardboard Kauramin particle board Paper Textiles

Maple Alder Patagonian cypress Purpleheart Andiroba Aspen Balsa Basralocus Tree heath Ebiara Birch Logwood Juniper Beech - European hornbeam Hornbeam - white Campeachy Aielé Kapok Douka Douglas fir Oak Oak - holm, English, durmast Emien Alder - red, black Ash Spruce Ash Yellow birch Southern yellow pine Hornbeam Hickory - silver poplar Hickory - poplar Izombé Guanandi Jarrah Elm Karri Chestnut - sweet, red African

Rubber tree Imbuia Kokrodua Niové Bidinkala Tola - real, red Cork Melamine particle board Phenolic resin particle board

Building materials

01 02 03 04

Concrete Screed Aerated concrete Gypsum plaster

Agba · Afrormosia

Page 7 of the Laserliner DampMaster user manual — Material temperature compensation
Page 7 · click to enlarge
Page 7

Material temperature compensation

Laserliner DampMaster — Material temperature compensation diagram (page 7)
Fig. 9 · Material temperature compensation

Relative material moisture is dependent on the temperature of the material. The device automati- cally compensates different material temperatures in that it measures ambient temperature and uses this measurement for its internal calculation.

However, the measuring device also offers an option for setting the temperature manually (see Step 14b) to increase measuring accuracy. This value is not stored and must be set again each time the device is switched on.

Laserliner DampMaster — Material temperature compensation diagram (page 7)
Fig. 10 · Material temperature compensation

LED display illumination can be varied with 3 different settings:

AUTO: Display illumination switches off during periods of inactivity and switches on again automati- cally for measurement procedures.

The setting is stored and remains in effect until it is changed manually.

Laserliner DampMaster — Material temperature compensation diagram (page 7)
Fig. 11 · Material temperature compensation

The units of measure for ambient temperature and material compensation can be set to either °C or °F. The setting is stored and remains in effect until it is changed manually.

14b

Page 8 of the Laserliner DampMaster user manual — Material temperature compensation
Page 8 · click to enlarge
Page 8
Laserliner DampMaster — Material temperature compensation diagram (page 8)
Fig. 12 · Material temperature compensation

The external hand-held electrode is suitable for all types of wood and soft building materials. The self-test function can also be performed with the external hand-held electrode (see Step 17). Be sure the connecting cap is securely attached to the DampMaster. When you are not using the hand-held electrode, always keep it stored in its carrying case to prevent injuries from being caused by the electrode spikes.

Page 9 of the Laserliner DampMaster user manual — Connecting deep electrodes (Art.-No. 082.023) with connecting cable (Art.-No. 082.022)
Page 9 · click to enlarge
Page 9

Connecting deep electrodes (Art.-No. 082.023) with connecting cable (Art.-No. 082.022)

Laserliner DampMaster — Connecting deep electrodes (Art.-No. 082.023) with connecting cable (Art.-No. 082.022) diagram (page 9)
Fig. 13 · Connecting deep electrodes (Art.-No. 082.023) with c…
Laserliner DampMaster — Connecting deep electrodes (Art.-No. 082.023) with connecting cable (Art.-No. 082.022) diagram (page 9)
Fig. 14 · Connecting deep electrodes (Art.-No. 082.023) with c…
Laserliner DampMaster — Connecting deep electrodes (Art.-No. 082.023) with connecting cable (Art.-No. 082.022) diagram (page 9)
Fig. 15 · Connecting deep electrodes (Art.-No. 082.023) with c…
1. Round deep-insertion electrode (non-insulated, ø 2 mm) for moisture measurements in building and insulating materials or between joints or joint intersections.
2. Round deep-insertion electrode (insulated, ø 4 mm) for moisture measurement in the concealed structure levels of multi-layer wall or ceiling structures.
3. Brush deep-insertion electrode for moisture measurement in a homogeneous building material. Contact is established by the brush tip.
4. Flat deep-insertion electrode (insulated, 1 mm flat) for targeted moisture measurement in the concealed structure levels of multi-layer wall or ceiling structures. Electrodes can, for example, be inserted through edge strips or at the wall-ceiling transition.

Applying deep electrodes The spacing of bore holes should be between 30 and 50 mm and be ø 6 mm for brush electrodes. After boring the hole, wait for about 30 minutes to allow moisture driven out of the hole by drilling heat to return to its original value. Otherwise measurement results could be falsified.

Page 10 of the Laserliner DampMaster user manual — other materials: ± 0.5 %
Page 10 · click to enlarge
Page 10

Technical revisions reserved. 04/09 Technical data

Measurement principle

Resistive material moisture measurement by way of integrated electrodes

Modes

3 wood groups 4 building materials Index mode for 15 additional building materials, Test mode

Measurement range / accuracy

wood: 0…30 % / ± 1 %, 30…60 % / ± 2 %, 60…90 % / ± 4 %

other materials: ± 0.5 %

Nominal temperature

25 °C

Permissible operating temperature

0 °C…40 °C

Permissible storage temperature

-10 °C…60 °C

Permissible max. relative humidity

85 %

Power supply

3 x lithium button cells, 3 V, type CR2032

Dimensions (W x H x D)

60 mm X 162 mm X 30 mm

Weight

0.169 kg

Warranty The warranty period is 2 years from the date of purchase. The warranty covers all material or manufactu- ring defects occurring during this time. The following are excluded from warranty: Damage due to improper use (e.g. operation with wrong type of current/voltage, connection to unsuitable power source, fall onto hard surface, etc.) or improper storage, normal wear and tear, and defects which only insigniÖ - cantly impair the value or suitability for use. Any tampering by unauthorised persons will render this warranty void. In the event that you need to claim warranty, please take the complete device together with all information and the invoice to one of our dealers or send it in to Umarex-Laserliner.

Ask about the Laserliner DampMaster

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Laserliner DampMaster

Be the first to ask — other owners or our team will answer.

Original document

Laserliner DampMaster manual PDF

84 pages·4.4 MB·Measuring instruments·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…