EN
Laserliner logo
Official user manual

Laserliner CableChecker

68 pages·4.5 MB·Miscellaneous·PDF·ENJA
Laserliner CableChecker
Table of Contents 15 sections Function / Application · Symbols · Safety instructions · Transmitter TX closed Transmitter TX open · … ShowHide
Page 1 of the Laserliner CableChecker user manual — Safety instructions
Page 1 · click to enlarge
Page 1

Read the operating instructions and the enclosed brochure “Guarantee and additional notices“ completely. Follow the instructions they contain. Safely keep these documents for future reference. !

Function / Application

  • Locates telephone wires, network cables, TV cables as well as wires and cables in electrical systems
  • Adapter for testing commonly used plug connections (RJ 11, RJ 45, TV-coax.)
  • Universal test terminals for connecting to any type of conductor
  • Loud audible signal for straightforward identification of selected cables

Symbols

Hazardous electrical voltage warning: Unprotected live components inside the device housing may pose a risk of electric shock.

Safety instructions

  • The structure of the device must not be modified in any way.
  • The device must only be used in accordance with its intended purpose and within the scope of the specifications.
  • Do not expose the device to mechanical stress, extreme temperatures or significant vibration.
  • Isolate the device from all measuring circuits before opening the battery compartment cover.
  • The device is not suitable for measurement whilst under voltage. Therefore, always make sure the measuring circuit is at zero voltage. Appropriate measures must be taken to ensure a zero-voltage state.
  • Do not perform any measurements in the vicinity of or directly a djacent to live cables! There is a risk of fatal electric shocks and damage to the device.
  • Check that all high-voltage capacitors are discharged.
Page 2 of the Laserliner CableChecker user manual — Receiver RECV
Page 2 · click to enlarge
Page 2
  • The sender introduces the measuring voltage into the lines to be tested. This may impair or damage sensitive electronic equipment (e.g. network cards). Therefore, please make sure that any lines to be tested which belong to sensitive electronic equipment are isolated before measurement.
  • The measuring tools and accessories are not toys. Keep out of reach of children.

Transmitter TX closed Transmitter TX open

Laserliner CableChecker — Transmitter TX closed Transmitter TX open diagram (page 2)
Fig. 1 · Transmitter TX closed Transmitter TX open

Receiver RECV

1 Receptacle for receiver RECV 2 ON / OFF switch (side) 3 Cover 4 Status LED 5 Opening for adapter 6 TV-coax adapter 7 Battery compartment 8 RJ 45 adapter 9 Cable terminals 10 RJ 11 adapter 11 Test prod 12 Status LED 13 Receiver signal volume control (side) 14 Test mode button 15 Speaker 16 Battery compartment

Page 3 of the Laserliner CableChecker user manual — Inserting the battery
Page 3 · click to enlarge
Page 3

Inserting the battery

Isolate the device from all measuring circuits before opening the battery compartment cover. It is recommended that you replace the batteries in the sender: When the status indicator light is weak. The batteries in the receiver should be replaced: If the signal volume becomes lower despite the fact that the position of the device or the volume control (13) has not changed. Do not switch on the device with the cover open.

Laserliner CableChecker — Inserting the battery diagram (page 3)
Fig. 2 · Inserting the battery

4 x LR44 1,5 V button cells 2 x 1,5 V type AAA

In order to preserve the batteries, the meter switches off automatically if it is left idle for 30 minutes.

2. Feed the required test adapter through opening (5)
5. Switch on transmitter (2), status indicator (4) flashes

Ensure correct polarity!

Page 4 of the Laserliner CableChecker user manual — a b
Page 4 · click to enlarge
Page 4
Laserliner CableChecker — a b diagram (page 4)
Fig. 3 · a b
3. Both devices are ready when a signal sounds and status indicator (12) lights
  • To locate the cable more efficiently, gradually reduce the receiver signal volume using the control (13). The cable can be located by means of volume differences and is indicated by the status LED (12) lighting up at its brightest or by the maximum signal volume.
  • The best search results are achieved when the test prod (11) has a direct metallic contact with the cable being located. This type of contact will produce a clearly audible jump in the signal. You can also get stronger signals at the cable ends (fig. a) or directly at the individual wires (fig. b).
  • Parallel supply lines may generate buzzing interference in the test lead. If the external interference is too great, switch off the household power supply during measurement if possible.
  • Any interference that occurs (buzzing, etc.) can be reduced by earthing the return conductor or shielding conductor in the test lead. Earthing by means of your own hand or finger may be enough, however.
Laserliner CableChecker — a b diagram (page 4)
Fig. 4 · a b
Laserliner CableChecker — a b diagram (page 4)
Fig. 5 · a b

a b

a b

Page 5 of the Laserliner CableChecker user manual — To avoid interference, disconnect all network plug connections. !
Page 5 · click to enlarge
Page 5

Trace cables 3

Make the measuring circuit zero-potential. Shields in the cable and in the surrounding area (metal coverings, metal supports, etc.) reduce the range of the receiver. !

Connect cable terminals (9) to the required cable. Then use the receiver to search for the line, with the test mode button (14) held down.

Laserliner CableChecker — Trace cables 3 diagram (page 5)
Fig. 6 · Trace cables 3

To achieve the maximum measuring depth, set the receiver signal volume as high as it will go (13).

To trace a single cable, connect the red terminal to the cable to be traced and the black terminal to earth (earthing conductor or shielding).

The signal is weak when connected to two signal lines within a cable. !

To locate LAN cables

Laserliner CableChecker — To locate LAN cables diagram (page 5)
Fig. 7 · To locate LAN cables

Connect the RJ 45 adapter (8) to a network socket. Then use the receiver to search for the line, with the test mode button (14) held down.

To avoid interference, disconnect all network plug connections. !

Page 6 of the Laserliner CableChecker user manual — To avoid interference, disconnect the building telephone service. !
Page 6 · click to enlarge
Page 6

To locate TV cables

Connect the TV-coax adapter (6) to a TV socket. Then use the receiver to search for the line, with the test mode button (14) held down.

To avoid interference, disconnect the building TV service. TV sockets in particular may contain filters that have a negative effect on measurements. In this case, remove the TV socket and perform the measurement directly at the cable. !

To locate telephone cables

Connect the RJ 11 adapter (10) to a telephone socket. Then use the receiver to search for the line, with the test mode button (14) held down.

To avoid interference, disconnect the building telephone service. !

Transmitter TX / Receiver RECV

Signal Multi-frequency pulse Max. input voltage 20 V DC Max. rel. humidity < 85% rH non-condensing Operating temperature -10°C…40°C Storage temperature -10°C…50°C

Max. output current 10 mA Max. signal voltage 8 Vss (peak-to-peak) Max. testing length 100 m Power supply 2 x 1,5 V type AAA Dimensions 80 x 152 x 46 mm Weight (incl. batteries) 185 g

Max. output current 30 mA SCAN mode measuring range 0 - 5 cm measuring depth Power supply 4 x LR44 1,5 V button cells Dimensions 26 x 148 x 17 mm Weight (incl. batteries) 45 g

Subject to technical alterations 01.16

Technical data · Transmitter TX · Receiver RECV

Page 7 of the Laserliner CableChecker user manual — EU directives and disposal
Page 7 · click to enlarge
Page 7

Information on maintenance and care

Clean all components with a damp cloth and do not use cleaning agents, scouring agents and solvents. Remove the battery(ies) before storing for longer periods. Store the device in a clean and dry place.

EU directives and disposal

This device complies with all necessary standards for the free movement of goods within the EU.

This product is an electric device and must be collected separately for disposal according to the European Directive on waste electrical and electronic equipment.

Further safety and supplementary notices at: www.laserliner.com/info

Ask about the Laserliner CableChecker

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Laserliner CableChecker

Be the first to ask — other owners or our team will answer.

Original document

Laserliner CableChecker manual PDF

68 pages·4.5 MB·Miscellaneous·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…