Instruction/ maintenance manual of the product FSP 44 Boca Research
Go to page of 32
Te c hni cal Manual Revisi on D: 0 4.18.08 FSP 4 2/44 /46 Flight Str ip Pr inter.
BOCA SYSTEMS, INC. © 2008 Boca Systems, Inc. All rights reser ved. Under the cop yright laws, this manual ma y not be copied, in whole or in par t, without the written consent of BOCA. Ev er y eff or t has been made to ensure that the inf or mation in this manual is accurate .
T able of Contents P age 1.0 Introduction 1 2.0 Unpacking the Printer 2 3.0 A tour of your printer 3 4.0 Installation 7 4.1 Loading Flight Strips 7 5.0 Standard Configuration 9 5.2 Control P anel Indicators 18 6.0. Interf ace Pinouts 19 7.0 Ther mal P aper - Theor y and Specification 20 8.
T able of Figures and Appendices P age Figure 1 P ackaging 2 Figure 2a Control P anel and LCD 3 Figure 2b Flight Strip Pr inter(FSP) 3 Figure 2c Cabinet Lock Mechanism 3 Figure 3a FSP side view 4 Figu.
FCC NO TICE NO TE: The equipment has been tested and f ound to comply with the limits for a class A digital de vice, pursuant to par t 15 of the FCC rules. These limits are designed to provide reasonab le protection against har mful interf erence when the equipment is operated in a commercial en vironment.
W ARRANTY INFORMA TION PRINTERS - BOCA warrants each pr inter to be free of def ects for a period of one y ear from the date of shipment when subject to nor mal use and service. This warranty co v- ers all par ts and labor e xcept f or the print head which is w arranted f or 90 days .
1.0 Intr oduction The BOCA Flight Str ip Printer, (FSP) is a direct thermal tick et printer with an int egrat ed cutting mechanism designed f or air traffic control en vironments. This manual will provide the user with general inf or mation regarding printer set-up , configuration and troubleshooting.
2.0 Unpac king the Printer The printer is shipped in a r uggediz ed container . Please sa ve pac king mater ial f or future use. Remov e the pr inter ( see figure 1 ) and accessories from the bo x and inspect f or obvious damage . If damage is noticed, please repor t it immediately to BOCA.
3.0 A T our of Y our Printer Figure 2b - Flight Strip Pr inter (FSP) 3 Output Slot (Hopper Mounting Holes) Figure 2a - Control P anel and LCD Figure 2c - Cabinet Lock Mechanism.
Figure 3a - FSP , Side View 4 A. Cutter Assemb ly B. Optical Detector C . Timing Belt D . Dr iv e Pulley (2) E. T ransf or mer F . Print Head Release Lev er A B C D E F NOTE: THE CUTTER ASSEMBLY MAY VARY DEPENDING ON THE DATE OF MANUFACTURE OF THE PRINTER.
5 Figure 3b - FSP , Cov er Open A. Print Head Release Lev er B. Logic Board C . LCD Control Board A B C NOTE: LOGIC BOARD CONFIGURATIONS MAY VARY DEPENDING ON THE DATE OF MANUFACTURE OF THE PRINTER.
Figure 4 - FSP , Rear View 6 A. A C P ower Connector B. Fuse Holder (2amp ,SB) C . Input Slot D. Interf ace Connector (Ser ial) E . Locking Mechanism F. ON/OFF Switch NOTE: CONFIGURATION MAY VARY DEPENDING ON THE DATE OF MANUFACTURE OF THE PRINTER FGL42 LOGIC BOARD CONFIGURATION SHOWN.
4.0 Installation The FSP is designed to be mounted on a counter top or shelf . Howe ver , prior to site and installation, the printer should be powered up and r un in the self test ay the printer flat on a counter . Please confirm that the line v oltage agrees with the v oltage listed on the label affix ed to the side of the unit (see figure 4).
F EED DIRECTION Figure 7 - Flight Strip loading Y ou ma y now install the printer in its per manent location. Adequate room should be provided behind the printer f or the smooth f eeding of stock. Begin loading flight strips through the entrance slot ( figure 7 ) with a smooth motion until the printer automatically positions the flight str ip .
5.0 Standar d Configuration The FSP is f actor y configured for specific customer requirements using an enhanced FGL package . Pr inting resolution is 300 dots per inch. F or complete inf or ma on the FGL Programming Language , please see the programming guide.
The char t below lists the present menu topics . These topics are subject to change . TEST TICKET TYPE? The FSP allows one of f our different test tic k ets to be pr inted when the pr inter’ s test button is pressed. In addition, this selection also deter mines other preset associated with the test tick et format selected.
MINI/MICR O? Defines the type of printer . MINI Is f or a printer with a Cutter Assembly (factory default) MICRO Is f or a printer without a Cutter Assembly PRINT SPEED? Controls the speed the tic ket tra vels at. Also eff ects the print quality . The numbers range from 0 - F ASTEST to 7 - SLO WEST .
SPECIAL HEAD? Is used when a special paper path size is installed (2.125”, 2.5”, 2.7”...) Here are the f ollowing choices: P A TH TYPE? Defines the number of paper paths used. Here are the f ollowing choices: BUFFER MODE? Defines when the printer will go busy .
INC CUT2 COUNT? Same as INC CUT1 COUNT? but eff ects path #2 on a dual path pr inter . (Does not apply) DEC CUT2 COUNT? Same as DEC CUT1 COUNT? but eff ects path #2 on a dual path pr inter . (Does not apply) 2-SIDED PRINTER? Only used with 2S tick et pr inters .
FLASH A CK MODE? Enables or disab les an ACK being sent bac k to the host after a flash operation. Y our choices are YES (Enabled) or NO (Disab led). NO is factory default. SOFTW ARE BUSY? Defines if the printer will go busy after each b yte is received.
15 5.1 THIS SECTION HAS BEEN REMOVED This page has been left blank intentionally.
Flash erase op era tion inc omplete Error No. De scription Ready Pa per Jam 1O N OFF 2 Flash Vpp problem OFF OFF Data O ut of paper 3 4 5 6 7 8 9 10 11 12 13 14 15 OF FO N O FF OFF Flash byte erase er.
6.0 Interface Pinouts Serial Pinouts RS232 (Standar d) Pin Function 2P r inter T ransmit 3P r inter Receiv e 7G round 5,20 DTR (Printer Ready) 4,22 R TS (+5Vdc) T ypical RS232 Pin Connections * Option.
7.0 Thermal P aper - Theory & Specification The print head’ s lif e expectancy is composed of both a mechanical and an electrical component. Both of these f actors are strongly influenced by the quality of the thermal paper used. MECHANICAL The print head has a theoretical rating of 60 kilometers.
8.0 Maintenance and Adjustments Y our tick et printer is solidly constr ucted and has been designed f or high volume use . I t requires minimal care to provide maximum ser vice. This section provides an o v er vie w of pr inter maintenance , including par t alignments, adjustment and replacement.
8.1.5.5 Tic ket Load Switch The tick et load switch should be positioned such that the printer automatically activ ates the stepper motor at the proper time when tick ets are loaded into the pr inter . When loading tick ets, the stepper motor should tur n on when the tic ket stops in front of the ther mal head.
8.1.6 THERMAL PRINT HEAD The print head should be cleaned per iodically to pre vent debris from building up on the print element. The required cleaning inter v al v aries greatly depending on the quality of the tick et stock and the amount of dust entering the pr int area.
Figure 9a - Print Head remov al Figure 9b - Print Head remov al Adjustment set screws 24 Remov e these two unmarked screws to replace print head. Figure Figure Figure 9c 9e 9d - Print Head remov al Clean this surface . Print Head release lev er . Head is installed wrong.
8.2 Cutter Assembl y 8.4 General Cleaning The interior of the pr inter should be cleaned whene ver there is a visib le accumulation of dust. Use a small vacuum f or cleaning. Be careful not to jar any of the printer’ s par ts loose. 25 The SC cutter (SC2) system is a fully integrated rotar y cutter mechanism pow er ed by a DC motor .
9.0 P AR TS LIST ITEM P ar t Number s Description 1 423182 CABINET , FSP 2 423182CV CO VER, FSP 3 423111FSP PRINT CA GE, FSP 4 421366FSP P APER GUIDE, FSP (LO WER) 5 421367FSP P APER GUIDE, UPPER 6 42.
10.0 T r oubleshooting Guide This is a simplified troubleshooting guide listing some of the typical prob lems. It is not intende d to provide technical details or repair methods , but can serve as a guide f or fault isolation in the field. If you need additional help , please contact BOCA at T el: (561) 998-9600 F ax: (561) 998-9609 1.
28 7. POOR PRINT OUT (light print out) a. Make sure the print head/cam lock assemb ly if fully locked in the closed position. b . Consult “Thermal Print Head” in Section 8.1.6 . c. Adjust print intensity setting via the control panel. Consult Section 5.
An important point after buying a device Boca Research FSP 44 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Boca Research FSP 44 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Boca Research FSP 44 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Boca Research FSP 44 you will learn all the available features of the product, as well as information on its operation. The information that you get Boca Research FSP 44 will certainly help you make a decision on the purchase.
If you already are a holder of Boca Research FSP 44, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Boca Research FSP 44.
However, one of the most important roles played by the user manual is to help in solving problems with Boca Research FSP 44. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Boca Research FSP 44 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
