EN
JVC logo
Official user manual

JVC MX-J552

28 pages·1014 KB·Audiosystem·PDF·ENDEFRITNLJA
JVC MX-J552
Table of Contents 80 sections About this manual · precautionary measures · The buttons on the device · The front panel · … ShowHide
About this manualp.1precautionary measuresp.1The buttons on the devicep.3The front panelp.3The remote controlp.5SLEEP SOUNDp.5MODEp.5DISPLAYp.5MODE PTY/EON .p.5CA-MXJ750Rp.5TAPE A/Bp.5REC START/STOPp.5CA-MXJ552R CA-MXJ550R CA-MXJ500p.5FM MODEp.5FADE MUTINGp.5Getting startedp.6Remove the device from the packagingp.6Connecting the antennasp.6The FM antennap.6Place the batteries in the remote controlp.6R6(SUM-3)/AA(15F)p.6ANTENNAp.6LOOP AM EXTp.6FM 75 COAXIALp.6AM (LW/MW) antennap.7Connecting the speakersp.7VOOR DE CA-MXJ750Rp.71 2, 3p.7AM EXTp.7AM LOOPp.7FM 75p.7COAXIALp.7VOOR DE CA-MXJ552R/CA-MXJ550R/CA-MXJ500p.7Connecting other equipmentp.8General functionsp.9Disable and disable the currentp.9DAILYp.9ON TIMEp.9RECp.9Select Player Resourcesp.9Set the clockp.9Adjust the volumep.10Select the sound modesp.10Enhance bass soundp.10HALL STAGE ROCKp.10POPp.10CLASSICp.10MANUAL 1 MANUAL 2 MANUAL 3p.10Create your own sound mode . . Manual Modep.11Looking up sendersp.12Look up pre-selection channelsp.12Programming of the shippersp.12Received FM transmitters with RDSp.13Search for program attributes by PTY codes (PTY search)p.13Change the RDS informationp.13Switch temporarily to a program of your choicep.14EXAMPLE 1p.14EXAMPLE 2p.14PTY SELECT EON SELECTp.14EXAMPLE 3p.14TA NEWS INFOp.14Play CDsp.15Loading CDsp.15Play whole CD CDs . .p.15Basic functions CDp.15Program the playback order of the songs . .p.16REPEAT ALL REPEAT 1CDp.17Lock CD Tray Lockp.17Play a cassettep.18Search for the beginning of a song . . Music Scanp.18Recordp.19Recording Cassettes on deck Bp.19Direct recording of CDp.203 CUT1 CUT2 CUT3 CUT4p.20Cassettes dubbingp.20Recording with Auto Editp.21Use the time functionsp.22Use the Daily Timerp.22TUNER FM TUNER AMp.22TAPE AUXp.22
Page 1 of the JVC MX-J552 user manual — precautionary measures
Page 1 · click to enlarge
Page 1
Diagram . .
Diagram . .

We thank you for purchasing one of our JVC products. Before using this device, it is advisable to read the manual carefully in order to get the best out of the device. Keep this manual so you can look up things later.

About this manual

Power supply • When you pull the plug from the wall contact, you must always pull the connector, never on the cord.

This manual is divided as follows:

  • The manual mainly deals with the operation and function of buttons on the device. You can also use the remote control buttons if they have the same or similar names (or markings) as on the device. If the remote control is different from that of the device, this will be explained.
  • General information that is the same for many functions is put together in one place and is not repeated before each action. For example, the information on how to turn off the device, set volume, change sound effects and other functions, which are explained in the section .General functions . . on pages 9 to 11 is not repeated over and over again.
  • This manual shall use the following markings:

NEVER touch the power cord with wet hands.

  • Condensation In the following conditions, condensation on the lens inside the device may occur:
  • Just after heating is switched on in a room
  • In a humid room
  • If the device is put directly out of cold in a warm place If this occurs, the apparatus may fail. In such a case, leave the device on for several hours so that it can evaporate moisture, remove the plug from the wall contact and put it back in.

Give warnings to prevent damage or risk of fire/electric shocks. Also provides information about operations that prevent the optimal operation of the device.

  • Other precautions
  • Should a metal object or moisture enter the device, you should remove the plug from your wall contact and consult your supplier before proceeding.
  • If you do not use the device for a longer time, remove the plug from your wall contact.

Provides information and suggestions on what you need to know.

NEVER disassemble the device, as it does not contain any parts that can be repaired by yourself.

If any malfunctions occur, remove the plug from the wall contact and contact the supplier.

precautionary measures

  • Installation
  • Place the device in a flat and dry place where the temperature does not reach 5°C or above 35°C.
  • The device must be properly ventilated to prevent overheating.
  • Keep a sufficient distance between the device and the television set.
  • Keep sufficient distance between the speakers and TV to avoid interference with the TV.

NEVER place the device near heat sources or in places where it is exposed to direct sunlight, excessive dust formation or vibration.

Page 2 of the JVC MX-J552 user manual — About this manual
Page 2 · click to enlarge
Page 2
Page 2 of the JVC MX-J552 user manual — About this manual
Page 3 of the JVC MX-J552 user manual — The front panel
Page 3 · click to enlarge
Page 3

The buttons on the device

Feel familiar with the function of buttons on the device.

The front panel

Diagram . .
Diagram . .

Press PANEL OPEN/ CLOSExanal to open. If you want to close the panel again, Press this button again.

Page 4 of the JVC MX-J552 user manual — The buttons on the device
Page 4 · click to enlarge
Page 4
Diagram . .
Diagram . .

For more information, see the page "P"s in brackets. The front panel 1 CD charge 2 button (standby/on) and StandBY light (9) 3 Display 4 For the CA-MXJ750R: SUBWOOFER VOLUME button (10) For the CA-MxJ552R/CA-M XJ550R/CA- MXJ500: ACTIVE BASS EX. LEVEL button (10) 5 Sensor remote control 6 TAPE 2 3 button and light (9, 18) This button also serves to enable the device. 7 AUX button and light (9) This button also serves to enable the device. 8 Deck A cassette holder (18) 9 0 EJECT button for deck A (18) p CD keys (CD1, CD2 and CD3) (15)

j 7 button (stop) (15 . . 21) k TUNING . / + buttons (12)

1 / ¡ buttons (fast left/fast right) (11, 16, 18) l SEA CONTROL button (11) / PROGRAM/RENDOM button (16, 17, 20) z EDIT button (21) x REPEAT button (17) c DISPLAY button (9) v SOUND MODO button (10) b CANCEL button (9, 17 22)

DEMO button (8) n Only for the CA-MXJ750R/CA-MxJ552R/CA-

  • MXJ550R: RDS function buttons (13)
  • DISPLY MODE, PTY/EONEN SELECT . / + buttons The display 1 Only for the CA-MXJ750R/CA-MxJ552R/CAMXJ550R: RDS function indications
  • Indications RDS, EON and TA/NEWS/INFO 2 Time clock indications
  • DAILY indicator (Daily timer), REC indicator (Recording timer) and SLEEP indicator (Drag timer);

These buttons also serve to enable the device. q 0 (buttons for opening/close CD-lade) (15)

These buttons also serve to enable the device. w VOLUME button (10) e CD £¥8 (play/ pause) button and light (9, 15)

  • -indicator (Timer) 3 Indications playback mode cd
  • Indications REPEAT (ALL/1CD/1), PROGRAM and RENDOM 4 Indications CD Numbers 5 Cd indications 6 Pattern indication SEA (Sound Effect Amplifier) 7 For the CA-MXJ750R: SUBWOOFER indicator (10) For the CO-MxJ552R/CA-M XJ550R/CA-M xJ500: BASS indicator (10) 8 Function indications tuner
  • MONOEN STEREOINDICATIONS 9 Indications of cassette functions
  • (Reverse mode), A/B (on-set cassette deck), 2 3 (playback direction of the cassette) and REC indicators p SOUND MDE indication q Main display

This button also serves to enable the device. Button PANEL OPEN/ CLOSE (9)

This button also serves to enable the device. t PHONES-jack (10) y FM/AM button and light (9, 12)

This button also serves to enable the device. u Deck B cassette holder (18, 19) i EJECT 0 button for deck B (18,19) The Roll Panel o PRESET . . / + buttons (12)

4 / ¢ (search/search backwards) buttons (9, 11, 16, 21 .0.24); REVERSE MODE button (18 .21) a REC START/ STOP button (19, 21) s DUBBING button (20) d CD REC STARTS button (20, 21), f TAPE A/ B button (18) g CLOCK/ TIMER button (9, 22 .24) h SET button (9, 12, 22 .10.24)

  • Displays the source name, frequency, etc.

Follow-up

Page 5 of the JVC MX-J552 user manual — FADE MUTING
Page 5 · click to enlarge
Page 5

The remote control

The remote control

1 Buttons CD numbers (CD1, CD2 and CD3) (15) These buttons also serve to enable the device. 2 SOUND MOD button (10) 3 TAPE A/B button (18) 4 REC START/STOP button (19), 21) 5 For the CA-MXJ750R: SUBWOFER + / . + / . . - buttons (10) 6 1 / 4 (quick left/ reverse) button (16 . This button also serves to enable the device. 8 FADE MUTING button (10) 9 AUX button (9) This button also serves to enable the device. p -button (standby/on) (9) q SLEEP button (24) w All for the CA-MXJ750R/CA-MxJ552R/CA-

SLEEP SOUND

MODE

DISPLAY

MODE PTY/EON .

CA-MXJ750R

TAPE A/B

REC START/STOP

CA-MXJ552R CA-MXJ550R CA-MXJ500

FM MODE

ACTIVE BASS EX.

MXJ550R: RDS function buttons (13) • DISPLAY MODE, PTY/EON and SELECT . . / + buttons e Number buttons (12, 16) r FM MODE button (12) t ¢ / I button (forward search/fast right) (16 . 18) y CD £¥8 button (9, 15)

FADE MUTING

This button also serves to enable the device. u 7 button (stop) (15 . . 21) i FM/AM button (9, 12)

This button also serves to enable the device. VOLUME + / .

When using the remote control, you should point it on the sensor for the remote to the front panel.

Show 9 more labels / short text on this page
p · q w · e · r · t · + · y · i u · o
Page 6 of the JVC MX-J552 user manual — FM 75 COAXIAL
Page 6 · click to enlarge
Page 6

Getting started

Remove the device from the packaging

Connecting the antennas

After you remove the device from the package, check that you have the following items present. The number in brackets indicates the number of items delivered.

The FM antenna

Diagram . .
Diagram . .
  • AM (LW/MW) antenna (1)
  • FM antenna (1)
  • Remote control (1)
  • Batteries (2)

Contact the supplier immediately if any of these items are missing.

Place the batteries in the remote control

1 Connect the FM antenna to the Fm 75 Ω COAXIAL Ending.

Place the batteries .R6(SUM-3)/AA(15F) .in the remote control by placing the + and .L on the batteries on the + or . When the remote control stops working, replace the two batteries at once.

2 - Fold the antenna.

3 Hang the antenna (for example along a wall or behind curtains) in such a way that it receives the best reception.

Information about the included FM antenna The FM antenna included with this device can be used as a temporary measure. If the reception is bad, you can connect an outdoor FM antenna.

R6(SUM-3)/AA(15F)

Connecting an outdoor FM antenna Before connecting the antenna, you need to disconnect the supplied FM antenna.

FM antenna for outdoors (not included)

ANTENNA

LOOP AM EXT

  • NEVER use an old battery along with a new one.
  • NEVER use different types of batteries together.
  • Do NOT expose the batteries to heat or open fire.
  • NEVER leave the batteries in the battery holder when you are not using the remote control for a long time. The device can then be damaged by leaking batteries.

FM 75 COAXIAL

You must use a 75 Ω antenna with a coaxial connection point (DIN 45325).

Follow-up

Page 7 of the JVC MX-J552 user manual — VOOR DE CA-MXJ552R/CA-MXJ550R/CA-MXJ500
Page 7 · click to enlarge
Page 7

AM (LW/MW) antenna

Connecting the speakers

VOOR DE CA-MXJ750R

1 2, 3

ANTENNA

Vinyl coated edge (not included)

AM EXT

AM LOOP

FM 75

COAXIAL

AM (LW/MW) antenna (loop included)

1 Connect the AM (LW/MW) antenna to the AM LOOP terminals, as shown on the image.

2 Turn the AM (LW/ MW) antenna until you find the best reception.

Connecting an AM (LW/MW) antenna for outdoor use If the reception is bad, connect one vinyl coated cord to the AM EXT connection point and fold it horizontally. (The AM (LW/MW) antenna must remain connected.)

VOOR DE CA-MXJ552R/CA-MXJ550R/CA-MXJ500

  • For better reception with both FM and AM (LW/ MW)
  • Make sure the antenna does not touch any other connecting points and wires.
  • Keep the antennas away from metal parts of the device, connecting cords and power cord.
Show 21 more labels / short text on this page
Blue · Loudspeaker cord (blue/black) · Ludder cord (black/blue) · Red · Black · Black * Ludzer cord · (red/black), · Speaker · Speakers · Right · Red * Loud-speakers cord · Red/black, the speaker cord · Black or black · Speaking speakers · Speakspeaking speakers
Page 8 of the JVC MX-J552 user manual — Connecting other equipment
Page 8 · click to enlarge
Page 8
Diagram . .
Diagram . .

1 Hold the clamp of the speaker stop at the back of the device.

Connect audio equipment with an optical digital input terminal You can record CDs on a connected digital device.

2 Place the end of the speaker cord in the stop point. When connecting the speakers, make sure that the polarity (colours) are similar: a on a and · on ·.

Diagram . .
Diagram . .

3 Let go of the clamp.

Before connecting the external equipment, remove the protective plug from the terminal.

Connecting other equipment

You can connect both analogue and digital equipment.

  • NEVER connect equipment while the power is switched on.
  • NEVER connect equipment to the power supply when all connections are not yet complete.

Connect an optical digital cord (not included) between the optical digital input terminal on the external device and the CD OPTICAL DIGITAL OUTPUT connection.

Connecting an analogue device Make sure you connect audio cords correctly: White plugs are for left-hand and red audio signals from right.

Now you can finally insert the device and connected external equipment into your wall contact!

Diagram . .
Diagram . .

When you insert the power cord into a wall contact, the display demonstration will be started automatically.

If you want to stop the demonstration, press any button on the device or remote control.

Diagram . .
Diagram . .

If you want to play external devices via this unit you must connect the AUX inputs of this unit using audio cables (not included) to the external device's audio outputs.

Start the display demonstration manually Hold DEMO for more than 2 seconds.

If you want to stop the demonstration, press any button.

Page 9 of the JVC MX-J552 user manual — Select Player Resources
Page 9 · click to enlarge
Page 9

General functions

4 Press 4 or on ¢ to set the right hour and then press SET.

Disable and disable the current

Diagram . .
Diagram . .

If you want to enable the unit, you should

Check the clock time display Press DISPLAY while the device is playing. • Every time you press this button, the source display and time display are displayed in turn on the display.

The roller panel will be opened automatically.

If you want to turn off the device (on standby), Press again so that the StandBY light will be lit.

Reset the clock If you have adjusted the clock before, press Clock/TIMER several times until the setting mode is selected. • Every time you press this button, one of the following clock modes is displayed:

The roller panel is also closed. Even when the device is on standby, a small amount of power is consumed.

DAILY

ON TIME

REC

If you want to completely disable the power supply, You can remove the power cord from the wall contact.

ON TIME Clock setting

(The time signal is blinking.)

(The hour digitals start flashing.)

When you disconnect the power cord or when a power failure occurs The clock is reset directly to .0:00 p.m. and the tuner pre-selection channels (see page 12) are deleted after a few days.

In case of power outages The clock loses the settings and is reset to .0:00.

Select Player Resources

Set the clock

If you want to listen to the FM/AM (LW/MW) channels, Press FM/AM (see page 12). If you want to play CDs, press CD £¥8 (see page 15 .l). If you want to play cassettes, press TAPE 2 3 (see page 18). If you want to select the external equipment as a source, Press AUX.

Before proceeding, set the built-in clock at the right time. Only on the device: 1 Press PANEL OPEN/CLOSE. The device is switched on and the roller panel will be opened automatically. 2 Press Clock/TIMER.

When you press the playback button for a particular source (FM/AM, CD £¥8, AUX and TAPE 2-3), the device is turned on and the roll-out panel automatically opens (and the device starts playing from its chosen source when it is ready).

The time display on the display starts to blink. 3 Press 4 or on ¢ to set the right hour and then press SET.

  • If you have pressed SET and want to correct the time mark, press CANCEL. The time tag's gonna blink again.

Canceled clockwise

Page 10 of the JVC MX-J552 user manual — HALL STAGE ROCK
Page 10 · click to enlarge
Page 10

If you use the remote control, press SUBWOOFER + if you want to increase the volume of the subwoofer or press SUBWOOFER .

Adjust the volume

You can only adjust the volume when the device is switched on.

Turn the VOLUME button in the direction of time to increase volume and counterclockwise to lower volume. • The volume level can be adjusted in 32 steps (MIN, FULL 1 .VOL 30, and MAX).

For the CA-MXJ552R/CA-MxJ550R/ CA- MXJ500 With the ACTIVE BASS EX. LEVEL button on this unit allows you to keep the full wealth of bass sound when listening to a playback source at low volume.

Diagram . .
Diagram . .

Turn the ACTIVE BASS EX. LEVEL button clockwise to strengthen the bass sound or counterclockwise to weaken it. • The bass sound can be adjusted step by step in 4 steps (BASS 1 . . BASS 3 and MAX).

With the remote control press VOLUME + to increase volume or turn it down on a more secure level.

Listen without disturbing others Connect headphones to the PHONES jacket. There won't be any sound coming out of the speakers. Make sure the volume is low when you plug in or put your headphones on.

The BASS indicator is always on when the unit is switched on.

If you want to use the remote control, click on ACTIVE BASS EX button. + press to strengthen the bass sound and on the ACTIVE BASS EX key. ..to reduce the bass sound.

Diagram . .
Diagram . .

NEVER turn off the device (on standby) when the volume is exceptionally high, because suddenly loud noise can damage your hearing, speakers and/or headphones when you switch on again. DO NOT REMEMBER that you cannot adjust the volume when the device is on standby.

If the Active Bass function wants to disable, you must turn the button against clock hands until the entry .BASS OFF .

Temporarily reduce volume Press the remote control on FADE MUTING. The volume is gradually reduced to . If you want to restore the sound again, Press this button again.

Select the sound modes

You can select one of the 6 preset sound modes (3 surround modes and 3 SEA (Sound Effect Amplifier) . The sound modes can only be used when playing, not when recording.

Enhance bass sound

If you want to select the sound modes, Press SOUND MODE until the desired sound mode is displayed on the display. The SOUND MOD indication is also illuminated on the display.

Denne funktion har kun indvirkining for afspilning og har ing betydning for din optelse.

For the CA-MXJ750R You strengthen and adjust the sound of subwoofers connected to the rear of this unit by means of the SUBWOOF VOLUME button (see page 7).

  • Every time you press this button, one of the following sound modes is displayed:

Turn the SUBWOOF VOLUME button clockwise to strengthen the sound of the subwoofer or counterclockwise to weaken it. • The sound of the subwoofer can be adjusted in 6 steps (WOOFER 1 . . WOOFER 5, and MAX).

Diagram . .
Diagram . .

Mr D. CLUB (Dance CLUB)

HALL STAGE ROCK

POP

CLASSIC

MANUAL 1 MANUAL 2 MANUAL 3

The SUBWOOFER indicator is always on when the unit is enabled.

(Canceled) · (Cancelled)

Page 11 of the JVC MX-J552 user manual — Create your own sound mode . . Manual Mode
Page 11 · click to enlarge
Page 11
Diagram . .
Diagram . .

Surround modes*: D.CLUB: Strengthens resonance and basses. HALL: Adds depth and brightness to the sound. STAGE: Adds brightness and spreads the sound,

2 Adjust the SEA pattern as desired.

1. Press 4 or ¢ to select the customized frequency range (LOW, MID, HIGH).

Like an outdoor stadium.

SEA modes (Sound Effect Amplifier): ROCK: Strengthens low and high frequencies. Suitable for acoustic music. POP: Suitable for vocal music. CLASSIC: Suitable for classical music.

2. Press 1 or I to adjust the level (from .3 to +3) of the selected frequency range.
Manual modesMANUAL1/2/3:
3. Repeat step 1) and 2) to adjust the level of the other frequency bands. 3 Press SEA CONTROL again.

Your own memory-saved sound mode. See .Join your own sound mode . . Manual mode. • .

Diagram . .
Diagram . .

OFF: Cancel sound mode.

* Surround elements are added to the SEA elements to create a feeling that you're there. When one of these modes is selected, the SOUND MIDE indication is illuminated as .

4 Press 4 or on ¢ to select one of the modes MANUAL 1, 2 or 3 in which you want to save the SEA pattern. 5 Press SEA CONTROL again.

When one of the SEA modes including manual mode (SEA elements without surround elements) is selected, it is illuminated as .

Diagram . .
Diagram . .

Create your own sound mode . . Manual Mode

  • You can change SEA patterns according to your own preference. These modified settings can be saved in the modes MANUAL 1, 2 and 3.
  • The next steps are subject to a time limit. If the setting is cancelled before you are finished, start again at step 1.
  • To include environmental effects in your SEA pattern, select one of the environment modes (D.CLUB, HALL or STADIUM) before following the procedure below.

The SOUND MODE indication is also illuminated. The SEA pattern you created is saved in the MANUAL mode selected from the previous step.

Apply your own sound mode Select MANUAL 1, 2 or 3 when using sound modes. See .The sound modes select .

ONLY ON THE Device: 1 Hold SEA CONTROL down until .SEA CONTJULY appears on the display.

Diagram . .
Diagram . .

The current level is displayed.

Page 12 of the JVC MX-J552 user manual — Programming of the shippers
Page 12 · click to enlarge
Page 12
Diagram . .
Diagram . .

Only on the device: 1 Find the transmitter you want to program. • See look up missionaries.

Looking up senders

Diagram . .
Diagram . .

1 Press FM/AM. The device is automatically switched on and tuned to the pre-selection transmitter (FM or AM . The roller panel will be opened automatically. • Every time you press this button, FM and AM (LW/MW) are chosen alternately. 2 Look up a station. On the device: Press the TUNING button . / + and hold it for at least 1 second. On the remote: Press the 1¥4 -key or the ¢¥¡-key and hold it for at least 1 second. The device starts by searching for channels and stops when a transmitter is found with sufficient signal strength. If a program is broadcast in stereo, the STEREO indication is illuminated.

2 Press SET.

3 Press PRESET . . / + to select a memory number.

4 Press SET again.

The transmitter of step 1 is stored under the memory number selected in Step 3. • If you save a new transmitter under a number that is already in use, the previously saved transmitter will be deleted.

Interrupt the search, Press the TUNING button . . / + (or 1¥4 or . · .).

If you use the TUNING . . / + button briefly and repeatedly (or on 1¥4 or ¢¥¡) press The frequency changes step by step.

When you disconnect the power cord or when a power failure occurs The programmed transmitters will be erased after a few days. If this happens, you need to reprogramme the transmitters.

Change the FM reception mode When receiving an FM broadcast in stereo is difficult or gives a lot of noise, press FM MODE on the remote until the word MONO appears on the display. The reception is better. If you want to restore the stereo effect, Press FM MODE again until the MONO indication is out. In this stereo mode, you can hear stereo sound when a program is broadcast in stereo.

Look up pre-selection channels

1 Press FM/AM. The device is automatically switched on and tuned to the pre-selection transmitter (FM or AM . The roller panel will be opened automatically. • Every time you press the button, FM and AM (LW/MW) are chosen alternately. 2 Select a memory number. On the device: Press PRESET . On the remote: Press the number keys. Press 5 if you want memory number 5

Programming of the shippers

You can program 30 FM transmitters and 15 AM (LW/MW) transmitters. In some cases, test frequencies are already stored in the tuner memory because the programming function has been tested at the factory. This is not a malfunction. You can save the desired channels in memory using the following programming method. • The next steps are subject to a time limit. If the setting is cancelled before you are finished, start again at step 1.

choose. Press +10 and then 5 if you

choose memory number 15. Press +10 and then 10 if you

select memory number 20. Press +10, +10 and then 5 as

you want to choose memory number 25. Press +10, +10 and then 10 if you

select memory number 30.

MHz

Page 13 of the JVC MX-J552 user manual — Change the RDS information
Page 13 · click to enlarge
Page 13

Received FM transmitters with RDS

This section of the manual is for models equipped with RDS functions (the CA-MXJ750R, CA- MXJ552R and CA-mXJ550R).

Search for program attributes by PTY codes (PTY search)

One of the advantages of RDS is that you can search for a particular type of program by specifying PTY codes. • See . .Additional information . on page 27 for more information about the PTY codes.

With RDS, FM transmitters can send an additional signal with the normal program signals. The broadcasters send the name of the channels, for example, as well as information about the type of program that is broadcast, such as sports or music etc.

  • Do not forget to program FM RDS transmitters by using the PTY codes in order to use EON function. See page 12 if you haven't done this yet.
  • The next steps are subject to a time limit. If the setting is cancelled before you are finished, start again at step 1. 1 Press PTY/EON until .PTY and .SELECT .
  • Whenever you press this button, one of the following RDS modes is displayed:

When you tune in to an FM transmitter that provides the RDS service, the RSS indication is illuminated on the display.

This device allows you to receive the following types of RDS signals.

PS (Programme Service):

This displays commonly known station names.

PTY (Program type):

This displays the type of program that is broadcast.

RT (Radiotext):

Diagram . .
Diagram . .

This displays text messages that the sender sends.

2 Press SELECT . . / + until the desired PTY code is displayed on the display.

EON (Enhanced Other Networks):

This will display information on the types of program performances broadcast by other RDS channels.

  • More information about RDS
  • Some FM transmitters and AM (LW/MW) transmitters do not send RDS signals.
  • Different FM RDS channels can offer different RDS services. Contact local radio stations if you want more information about the RDS services in your area.
  • RDS may not function properly if the receiving transmitter does not send signals correctly or if its signal strength is weak.
  • Whenever you press this button, one of the following PTY codes is displayed:

NEWS . . AFFAIRS . INFO . SPORT . M . . LIGHT M ♪ CLASSICS . OTHER M . WEATHER . FINANCE . CHILDREN . SOCIAL A . RELIGION . PHONE IN . TRAVEL . LEISURE . JAZZ . COUNTRY . NATIONAL . OLDIES . 3 Press PTY/EON again. During the search, in turn .SEARCH's and selected PTY code are displayed. The device searches 30 programmed FM channels, stops as soon as the selected program is found by you (see WEETFOUNDS) and matches it. • If no program is found, the words "NOT" and "FOUND" are displayed in turn and the device returns to the last received transmitter.

Change the RDS information

You can read RDS information on the display while listening to an FM transmitter.

Press DISPLAY MODE. • Every time you press this button, the following information is displayed:

Diagram . .
Diagram . .

Station frequency (or preset channel no.) (or programmed channel number)

If a transmitter does not emit PS, PTY or RT signals The main display shall show .--- --- PS, .‐---"--"--."--""--

If it takes a long time before the RDS information received from a transmitter is displayed • • PTYS or • WAIT RTS may be displayed in the display.

Stop the search Press PTY/EON while searching.

Page 14 of the JVC MX-J552 user manual — TA NEWS INFO
Page 14 · click to enlarge
Page 14

Switch temporarily to a program of your choice

This is how the EON function works:

EXAMPLE 1

  • Thanks to the receipt of EON information from FM RDS transmitters, the device can temporarily switch with the EON function to a broadcast program of its choice (TA, NEWS and INFO) from another channel.
  • The EON function only works if you listen to a programmed FM RDS transmitter that transmits EON information.
  • The EON indication will light up when you receive a transmitter with EON information.

If there is no channel to be found that will broadcast the selected program The device remains tuned to the current transmitter.

. . As soon as a transmitter starts broadcasting the program you selected, the device automatically switches to the appropriate transmitter. The indication for the PTY code received is starting to blink.

. . When the program is finished, the main display .EON ENDS shall show and the device will return to the previously selected transmitter but the EON function will remain active.

  • Activate EON: DO NOT REMEMBER that you need to program FM RDS transmitters in order to use the EON function. See page 12 if you haven't done this yet.
  • The next steps are subject to a time limit. If the setting is cancelled before you are finished, start again at step 1. 1 Press PTY/EON until .EON and .SELECT .
  • Whenever you press this button, one of the following RDS modes is displayed:

EXAMPLE 2

If there is a channel that will broadcast the selected program The device matches the selected program. The indication for the PTY code received is starting to blink.

. . When the program is finished, the main display .EON ENDS shall show and the device will return to the previously selected transmitter but the EON function will remain active.

PTY SELECT EON SELECT

2 Press SELECT . . / + until the desired EON data type is displayed on the display. The indication for the selected EON data type is also shown.

EXAMPLE 3

If the FM transmitter you are listening to is sending out the selected program The device continues to receive the transmitter, but the indication for the PTY code received starts blinking.

. . When the program is finished, the indication for the received PTY code stops flashing and burns continuously but the EON function remains active.

  • Each time you press this button, one of the following EON data types is displayed:
  • More information about the EON function
  • EON information from some channels may not be compatible with this device. If this is the case, the EON function may not work properly.
  • When listening to a program that is tuned with the EON function, it does not switch to another station even though another transmitter starts broadcasting a program containing the same EON information.
  • The EON function will be cancelled when you change the source to CD, TAPE or AUX; the feature will be temporarily canceled if you modify the source into AM.

TA NEWS INFO

TA: Traffic information NEWS: News INFO: Programme performance indicators intended to provide information in the broadest sense of the word. OFF: The EON function has been cancelled. The indication for the EON data type (TA, NEWS, INFO) is based. 3 Press PTY/EON again. The indication for the EON data type stops flashing and burns continuously. The EON function is now activated. See .This is how the EON function works.

Cancelled · OFF (Canceled)

Page 15 of the JVC MX-J552 user manual — Basic functions CD
Page 15 · click to enlarge
Page 15

Play CDs

Loading CDs

Play whole CD CDs . .

Only on the device: 1 Press 0 for the CD-lade (CD1 to 3) in which you want to play a CD. The device is automatically switched on and the CD drawer slides out. The roller panel will be opened automatically. 2 Place a CD correctly on the circle of the CD drawer, with the label pointing upwards.

You can play CD DVDs continuously. 1 Place the desired CDs. 2 Press the buttons of CDs (CD1, CD2 and CD3) you want to play. The CD will be played from the first track of the selected CD.

Songs of the current CD

Diagram . .
Diagram . .

Number of the played song

  • When using a CD-single (8 cm), place it on the inside circle of the CD-lade. 3 Press the same 0 as in step 1. The CD-lade is closed and the corresponding CD-indication (CD1 to CD3) is illuminated on the display. 4 Repeat steps 1 to 3 to insert the remaining CD-ROMs.
  • If you press CD £¥8 instead of the numbered buttons, then the corresponding CD will be played (if there is a CD in one of the load).

If you want to interrupt the playback, Press 7.

If you want to remove the CD, Press 0 of the corresponding CD-lade.

  • Order of CD playback When you have 3 CD playouts in the load, they are played in one of these order:
  • When you press CD1: CD1 ] CD2 ] CD3 (stops after that)
  • When you press CD2: CD2 ] CD3 ] CD1 (stops after that)
  • When you press CD3: CD3 ] CD1 ] CD2 (stops after that) * When only 2 CDs are placed, they will be played in the same order, skipping the drawer without a CD.

If you want to play more than one CD continuously When you press 0 to insert the next CD, the first CD tray will be automatically closed and the next drawer will slide out.

Information on the cd indications Each CD indication corresponds to the CD-lade with the same number.

Diagram . .
Diagram . .

Basic functions CD

When playing a CD, you can use the following functions.

Switch CDs while playing another CD Press the 0 corresponding to a CD that is not playing or selected at this time, to remove and change this CD from the drawer. If you switch CDs while playing, playback will only stop when all the CDs that you have switched are played.

  • The CD marking for the CD number you have chosen will be illuminated.
  • The CD indication flashes while the corresponding CD is played.
  • The CD indication will go off when the device signals that there is no CD in the corresponding drawer.

Interrupt playback temporarily Press CD £8 When playback is temporarily interrupted, the expired playing time blinks on the display. If you want to resume the playback, Press CD £¥8 again.

Page 16 of the JVC MX-J552 user manual — Program the playback order of the songs . .
Page 16 · click to enlarge
Page 16
  • Every time you press this button, one of the following CD modes is displayed:
  • Look up a particular fragment in a song Keep 1 or ¡ pressed while playing.
  • 1 : Replay the song quickly.
  • ¡: Quick forward playback of the song. When you use the remote control, hold down 1/4 or ¢ / ¡.
Diagram . .
Diagram . .

3 Press the buttons of CD DVDs (CD1, CD2 and CD3) you want to play.

  • Go to another song Press before or while playing several times at 4 or ¢ .
  • 4:Back to the beginning of the current or previous number.
  • ¢ :To the beginning of next or subsequent numbers. When you use the remote control, hold down 1/4 or ¢ / ¡.

CD Number Program Step Number

If you: 4 or ¢ Holds (or 1 / 4 or ¢ / ¡ before playing) You can change the numbers continuously.

4 Select a song from the cd selected in previous step. On the device: Press 4 or on ¢ to select the desired number and then press SET.

Go straight to another number using the cipher keys If you press the number key(s) before or while playing, you can play the desired song.

For example: Press 5 if you want number 5

choose. Press +10 and then 5 if you want to choose number 15. Press +10 and then 10 if you want to choose number 20. Press +10, +10, and then 2 if you want to choose number 32.

On the remote: Press the number keys. • See .Just go to another number with the numbers keys .For more information about using the digits keys.

Diagram . .
Diagram . .

Program the playback order of the songs . .

  • Before playing, you can choose the order in which to play the songs. You can program up to 32 numbers in advance.
  • If you want to repeat the programmed numbers (see page 17), press REPEAT after starting the playback program. 1 Place the desired CDs.
  • If the current playback source is not the CD player, press CD £¥8 and then 7 before going to next step. 2 Press PROGRAM/ RANDOM several times until .PROGRAM . . is displayed on the display.
  • 5 Programme the other songs you want to listen to.
  • If you want to program songs from the same CD, repeat step 4.
  • If you want to program numbers from another CD, repeat steps 3 and 4. 6 Press CD £¥8 . The songs will be played in the order you programmed.

If you want to interrupt the playback, Press 7.

If you want to interrupt the program, press PROGRAM/ RANDOM again several times before or after playing until another playback mode is started. (The program you created will be stored in memory until you disable the device or erase it.)

  • If a program is stored in memory, this program will be called.

Follow-up

Page 17 of the JVC MX-J552 user manual — Lock CD Tray Lock
Page 17 · click to enlarge
Page 17
Diagram . .
Diagram . .

If you want to interrupt the playback, Press 7. • Random playback will also be terminated when one of the CD loads is opened.

Check the contents of the program Before playing, you can check the contents of the program by pressing on the remote control 1/4 or ¢ / ¡.

If you want to interrupt the random playback, Press PROGRAM/RENDOM again several times before or after playing until another playback mode is started.

  • ¢ / ¡:Represents the programmed numbers in the programed order.
  • 1 / 4 :Represents the numbers in reverse order. Change the program Before playing, you can delete the programmed numbers displayed on the display by pressing CANCEL.
  • Whenever you press this button, the displayed programmed number is deleted from the program. If you want to add songs to the program before playing, select the numbers that you wish to add by performing step 4 of the programming procedure on page 16. If you want to erase the entire program before or after playing, press 7. . .PROGRAM . is displayed on the display.
  • If you have a CD drawer slided out, the programmed tracks of this CD will also be deleted from the program.

Even if you have 4 press (or on 1 / 4 on the remote) You cannot go back to the previous tracks during random playback. Repeat track or CD CDs . .

You can repeat all the cdws, the entire program or individual songs that are currently being played as often as you like. If you want to repeat the playback, press REPEAT during or before playing. If you want to repeat program performances and play randomly, press REPEAT after the playback has started. • Every time you press this button, the following repetition mode is chosen, with the following indication illuminated on display:

If you try to include a 33rd number in the program,.

REPEAT ALL REPEAT 1CD

REPEAT 1 Canceled (Continuous play)

REPEAT ALLRepeats all tracks on all CD drives (continuously)

If the specified number is ignored You have tried to program a song from an empty CD-lade or a number that does not exist on the chosen CD (if you choose for example number 14 on a CD with only 12 numbers). In such cases the numbers given are ignored. Play in random order

or in random order) or all the numbers in the program. REPEAT 1CD*: Repeats all songs on one CD. REPEAT 1: Repeats one song on one CD. * REPEAT 1CD is not used for program playback and playback in random order.

If you want to cancel it again, Press REPEAT several times until the REPEat indication (REPEAT ALL, REPEATE 1CD or REPE AT 1) goes out on display. • Replay is also cancelled when you select program playback or playback in random order.

  • The numbers of all the CDs placed are played in random order.
  • To repeat the random playback, press REPEAT after you have started playing randomly. 1 Place the desired CDs.
  • If the current playback source is not the CD player, press CD £¥8 and then 7 before going to next step. 2 Press PROGRAM/ RANDOM several times until .RANDOM .Pump the display.

Lock CD Tray Lock

You can lock the CD drawer so that the CD loads cannot slide out. • This function can only be used by means of the buttons on the device.

Diagram . .
Diagram . .

If you want to lock a CD drawer, Press 0 for the desired CD while holding 7. (If a CD-lade is opened, close it first.) •LOCKED • Shortly display the cd-lades and lock them in the drawers.

  • Every time you press the button, one of the following CD modes is displayed:
Diagram . .
Diagram . .

If you want to remove the lock of the CD drives, Press 0 for the desired CD while holding 7. •UNLOCKED • Shortly displayed, the cd-locking is removed in the drawers.

3 Press CD £¥8. The songs are played in random order. The random playback will be terminated once all the songs have been played.

If you try to remove a CD from the drawer, it will be.LOCKED . to indicate that the CD-ROMs are locked.

If you want to skip the track that is playing for the rest, Press ¢ (or on the remote control)

Cancelled · (Continu Playback)

Page 18 of the JVC MX-J552 user manual — Search for the beginning of a song . . Music Scan
Page 18 · click to enlarge
Page 18
Diagram . .
Diagram . .

You can play cassettes of type I, type II and type IV without changing the settings.

Repeat both sides of . Reverse Mode works for both decks at the same time. When this mode is enabled, the end of one side of the cassette automatically plays the other side and then repeats the same process.

Play a cassette

If you want to enable Reverse Mode, press REVERSE MODE until the Reverse Mode indication is illuminated on display as a .

1 Press EJECT (0) for the cassette deck you want to use.

If you want to disable Reverse Mode, Press REVERSE MODE again until the Reverse Mode indication is illuminated on display as .

When Reverse Mode is enabled while in deck A and B a cassette is placed After the back (2) of the cassette is played, the tape is played in the other deck.

2 Place a cassette with the tape down.

Search for the beginning of a song . . Music Scan

Diagram . .
Diagram . .

You can use Music Scan to look up the beginning of a particular song. Music Scan searches for the empty parts on the cassette that are usually inserted between songs, after which the next track is played.

Find the start of the current number When playing, press 1/¡ (1/4 or ¢ / ¡ on the remote control) the opposite direction of play from the cassette. The indicator for the opposite direction of play slowly flashes on the display.

3 Close the cassette holder carefully. If you place a cassette in deck A and deck B, the tape that you last placed will be selected for playback. If you want to use the other deck, press TAPE A/B . 4 Press TAPE 2 3. The cassette is played and the directional indication (2 3) starts to blink slowly in order to indicate the direction of playback of the tape. • Every time you press this button, the direction of play of the cassette changes.

The search will stop automatically at the start of the current track, after which the current song will be played again automatically.

Find the beginning of the next song When playing, press 1/¡ (1/4 or ¢ / ¡ on the remote control) same play direction from the cassette. The indication of the same direction begins to blink slowly and quickly in turn. The search stops automatically at the beginning of the next track, after which the following number is played automatically.

3. the front is played. 2 : This is the backside of this. When the cassette is played to its end, it will be automatically stopped if the Reverse mode is not enabled. (See .a) Repeat both sides of the page .
  • Music Scan searches for an empty 4 seconds between the songs, so it will not function properly in the following cases
  • There is no empty part at the beginning of a song.
  • There is noise (often caused by frequent use or bad copying) on the empty area.
  • Long, very soft passages or breaks in a song.

If you want to interrupt the playback, Press 7.

If you want to use the other deck, press TAPE A/B and then fold on TAPE 2 3.

If you want to fast flush left or right, Press 1/¡ (1/4 or ¢ / ¡ on the remote control) while not playing. The indication for the direction of play (2 3) starts to blink quickly on the display.

Thickness C-120 or even thinner cassettes are not recommended, as these tires quickly lose quality and easily become entangled in the clamp rollers and guide wheels.

If you want to remove the cassette, Press 0 EJECT for deck A or EJECT 0 for deck B.

For cassette deck B · For cassettedeck A

Page 19 of the JVC MX-J552 user manual — Recording Cassettes on deck B
Page 19 · click to enlarge
Page 19

Record

  • IMPORTANT:
  • It may be illegal to record or play copyrighted material without the consent of the copyright holder.
  • The recording level is automatically set correctly and thus is independent of the volume level (and the subwoofer level on the CA-MXJ750R, active balevel at the CA -MX J552R, CA - MXJ550R and CA - mXJ500). So while making a recording, you can adjust the sound that you are listening to without affecting the recording you're making.
  • During recording, any sound modes that are switched on can be heard via the loudspeakers and headphones. However, sound effects are not included (see page 10).
  • If your recordings show too much noise or cracking, the device may be too close to a television set. Keep a sufficient distance between the device and the television set.
  • You can use type I and II cassettes for recording.

Recording Cassettes on deck B

1 Press EJECT 0 for deck B.

  • 2 Place a tape cassette with the belt down. 3 Close the cassette holder carefully. 4 Check the direction of playback for deck B.
  • If the direction of play is not correct, press TAPE 2 3 twice and then 7 to change the direction. 5 Start playing the source . . FM, AM (LW/ MW)*, CD player, deck A or external equipment connected to AUX jacks.
  • When the source is a CD, you can also use CD Direct Recording (see page 20) and Auto Edit Recording.
  • When the source is cassette deck A, you can also use the dubbing method. (See .Cassettes dubben . on page 20.)

Secure the recordings against erase On the back of cassettes there are two tabs to prevent accidental deletion or new recording. Remove these tabs to protect the recording from erase. If you still want to record on a secure cassette, cover the holes with tape. When using a type II cassette, make sure you do not cover the holes intended to determine the type of cassette.

*See .One AM (LW/MW) transmitter record . . Beat Cut . on page 20. 6 Beggings. On the device: Tryk på REC START/ STOP. On the remote control: Hold REC START/STOP inde i mindst 1 secund.

  • The best sound quality for recording and playing If the heads, guide wheels and clip rollers of cassette decks become contaminated, the following may happen:
  • Reduction of noise quality
  • Discontinue sound
  • Blur the sound
  • Delete incomplete
  • Recording problems Clean the heads, guide wheels and clamp rollers Use a alcohol-wetted cotton wool.

The REC indicator on the display is activated and the recording starts. If you want to end the recording, press the REC START/STOP button again or press 7. If you want to remove the cassette from the deck, Press EJECT 0 for deck B. Recording on both sides . . Reverse Mode Press REVERSE MODE until the Reverse Mode indication is illuminated as . • When you use the Reverse mode for recording, first take forward (3). Otherwise, recording is stopped after only one side of the cassette has been recorded. If you want to disable Reverse Mode, press REVERSE MODE again until the Reverse Mode indication is illuminated as .

Demagnetize the heads Turn off the device and use a demagnetization device for heads (available at electronics shops and record stores).

Clip rolls Guide wheels · Head

Page 20 of the JVC MX-J552 user manual — 3 CUT1 CUT2 CUT3 CUT4
Page 20 · click to enlarge
Page 20

Record an AM (LW/MW) transmitter . . When you record an AM (LW/MW) broadcast, it is possible that you will hear sound vibrations (which are never audible when listening to the broadcast without recording them). If this happens, press PROGRAM/RENDOM several times while recording until the sound vibrations are less audible. • Every time you press this button, the following information is displayed:

Direct recording of CD

Everything on the CD is recorded in the same order as on the cd, or in the sequence you specified for Program play. 1 Place a recording cassette in deck B. 2 Place a CD correctly on the circle of the CD drawer, with the label pointing upwards. 3 Press one of the CD buttons (CD1 to CD3) to select your desired CD and then press 7. 4 Press CD REC START. The entry .CD RECO shall appear and the REC indicator on the display will be displayed. Deck B starts the recording and the CD player starts playing. When the recording is complete, .CD REC FINISHED .v will be displayed on the display and then the CD player and deck B stop.

3 CUT1 CUT2 CUT3 CUT4

Cassettes dubbing

It is recommended to adjust the cassette type (type I or II) for recording according to the original type.

1 Press TAPE 2 3 and then on 7.

If you want to end the recording that is made using this recording method, press 7 or the REC START/ STOP button.

2 Place the source cassette in deck A and a recording cassette in dek B. • Place the cassettes in the two decks so that they are played forward (3). 3 Press DUBBING. The recording is starting.

Recording on both sides . . Reverse Mode Press REVERSE MODE until the Reverse Mode indication is illuminated as .

  • When you use the Reverse Mode for recording directly from CD, first record forward (3 ). When there is no room left on the tyre while a number is recorded ahead (3 ), the last song is recorded at the beginning of the rear (2 ). If you start recording on the back (2 ), recording is stopped when only one side of the cassette is recorded.

If you want to interrupt recording, Press 7.

Recording on both sides . . Reverse Mode Press REVERSE MODE until the Reverse Mode indication is illuminated as .

If you want to disable Reverse Mode, press REVERSE MODE again until the Reverse Mode indication is illuminated as .

If you want to disable Reverse Mode, press REVERSE MODE again until the Reverse Mode indication is illuminated as .

Follow-up

Page 21 of the JVC MX-J552 user manual — Recording with Auto Edit
Page 21 · click to enlarge
Page 21
Diagram . .
Diagram . .

Recording with Auto Edit

Diagram . .
Diagram . .

If you are using Auto Edit when recording, you can record the songs of CD in such a way that they fit on the cassette. Auto Edit creates a program by selecting the CD numbers in numerical order. To avoid the end of the last track being broken down on the front, the latter number is chosen in such a way that it fits the remaining part of the tyre.

Numbers to be recorded on the rear side (SIDE-B) are displayed.

  • Every time you press this button, the numbers to be recorded at the front (SIDE-A) and on the back (SIDE -B) will be displayed in turn. 5 Place a recording cassette of the correct length in deck B. 6 Press REVERSE MODE until the Reverse Mode indication is illuminated as .
  • If you do not enable Reverse Mode () the recording will stop as soon as the front of the cassette is recorded. 7 Press CD REC START. The REC indicator on the display is connected. On deck B the recording starts, after which about 10 seconds later the CD player starts playing. When the recording is complete, .CD REC FINISHED's display will be displayed and then the cd player and deck B stop.
  • If a cassette has not been flushed back, this is done on deck B before the recording starts.
  • An empty 10 seconds part is automatically inserted at the beginning of each side of the cassette.

Only on the device: 1 Place your desired CDs. • If the current playback source is not the CD player, press CD £8 and then 7 before going to next step. 2 Press EDIT.

3 Press the CD button (CD1 to CD3) of the CD you want to record.

Interrupt the Auto Edit recording Press 7 or REC START/STOP to insert an empty 4 seconds portion on the tape. (An empty part of 4 seconds is important when using Music Scan . see page 18.)

End the recording made by this recording method Press the CANCEL key during or after playing. • You can also end recording by pressing one of the following keys . . 7, REC START/ STOP and PROGRAM/ RENDOM.

The optimal band length for the CD is displayed.

Manually change the tyre length If the selected tyre length is not satisfactory, you can change it by pressing 4 or ¢. For the tyre length you can choose from the following values: . .

Page 22 of the JVC MX-J552 user manual — DAILY
Page 22 · click to enlarge
Page 22

Use the time functions

There are three time functions . . Recording Timer, Daily Timer and Sleep Timer.

2 Press Clock/TIMER again.. . TIME . shall be displayed for 2 seconds, and the time setting mode shall be enabled.

Diagram . .
Diagram . .

Before you can use the time functions, set the clock in the device at the right time. (See page 9.)

Use the Daily Timer

Daily Timer allows you to be awakened by your favorite music or radio program.

3 Set the time you want the device to be enabled. 1) Press 4 or ¢ to set the right hour and then press SET. 2) Press 4 or ¢ to set the minutes and then press SET. .OFF TIME .At the same time, it will be displayed for 2 seconds and then the time setting mode for switching off is switched on. 4 Set the time you want to turn off the device (set on standby). 1) Press 4 or ¢ to set the right hour and then press SET. 2) Press 4 or ¢ to set the minutes and then press SET. Enables the source selection mode.

  • This is how the Daily Timer works The device is automatically switched on, the volume is set to its preset level and the specified source is played when the time has been set (the indication starts blinking just before that and it keeps flashing as long as the time function works). Then the device is automatically switched off at the preset time (SUPFS starts flashing just before). The settings of the time function remain in memory until you change it.
  • The next steps are subject to a time limit. If the setting is cancelled before you are finished, start again at step 1.
  • If you make an error while setting the time function, press CANCEL. (This does not always work. If CANCEL does not work, press Clock/ TIMER several times and start again at step 1.)
Diagram . .
Diagram . .
Diagram . .
Diagram . .
  • Before you begin...
  • If you want to play a CD, make sure that you select the CD-lade in which the CD is placed.
  • If you want to play a cassette . . . If the direction of play of the cassette is properly set, check that it is in place.
  • If you set the external device as a playback source, make sure that its timer is set at the same time.

5 Press 4 or on ¢ to select the source and then press SET. • Whenever you press 4 or ¢, one of the following sources is displayed:

Only on the device: 1 Press CLOCK/TIMER until .DAILY . The DAILY(Daily Timer) indication also starts blinking on the display.

TUNER FM TUNER AM

TAPE AUX

– CD – –

TUNER FMaligns with a preset FM-

Transmitter. = go to step 6. TUNER AM: adjusts to a preset AM (LW/

MW) transmitter. =Go to step 6. . CD ♪ . .: plays a CD from a given number of

a certain CD. = go to step 6. TAPE: plays a cassette in deck A or deck B. = go

To step 7. AUX: Play an external source. = go to step 7.

  • Each time you press this button, one of the following time modes is displayed:

DAILY

ON TIME

REC

ON TIME Clock setting

(see page 9)

Continuation · Klokin- thesis Cancelled · Canceled

Page 23 of the JVC MX-J552 user manual — DAILY
Page 23 · click to enlarge
Page 23

6 When selecting . CD . . Press 4 or ¢ to select the CD-number and then press SET. 2) Press 4 or ¢ to set the playback track and then press SET. The volume setting mode is enabled. When selecting .TUNER FM Press 4 or ¢ to select the programmed transmitter number and then press SET. The volume setting mode is enabled. 7 Press 4 or on ¢ to set the volume. • To adjust the volume, you have to choose between . . If you select .VOL . .

If the device is enabled when time set starts The Daily Timer function is not working.

Use the Recording Timer

Recording Timer allows you to record a radio broadcast automatically on a cassette.

  • This is how the Recording Timer works The device is automatically switched on, tunes to the specified transmitter, sets the volume at . . MIN . and starts recording when the set time has arrived (the indication begins to blink immediately before it keeps flashing while the time function is working). Then the device is automatically switched off at the preset time (SUPFS starts flashing just before). The settings of the time function remain in memory until you change it.
  • The next steps are subject to a time limit. If the setting is cancelled before you are finished, start again at step 1.
  • If you make an error while setting the time function, press CANCEL. (This does not always work. If CANCEL does not work, press Clock/ TIMER several times and start again at step 1.)
Diagram . .
Diagram . .

8 Press SET to complete the Daily Timer settings. The DAILY (Daily Timer) indication stops blinking and burns continuously. The settings you specify will be displayed in the correct order on the display. 9 Press to disable the device (to be switched on standby) if you have set the Daily Timer while the device was turned on.

ONLY on the device: 1 Place a recording cassette in deck B. 2 Press CLOCK/TIMER until .RECOFF is displayed on the display. The REC (Recording Timer) indication also starts to blink on the display.

In or off Daily Timer after you have specified settings

  • Each time you press this button, one of the following time modes is displayed:

1 Press Clock/TIMER several times until .DAILY . 2 If you want to disable the Daily Timer, press CANCEL. The DAILY indicator (for the Daily timer) is displayed on the display (the entry .OFFS shall appear for some time). The Daily Timer has been cancelled, but the settings for the Daily Timers are kept in memory. If you want to turn on the Daily Timer, press SET. The DAILY indicator (for the Daily timer) on the display is illuminated. The settings you specify will be displayed in the correct order on the display, so that you can confirm them.

DAILY

ON TIME

REC

Klokinstelt (see page 9.)

ON TIME Clock setting

3 Press Clock/TIMER again.. . TIME . shall be displayed for 2 seconds, and the time setting mode shall be enabled.

Diagram . .
Diagram . .

Cancelled · Canceled

Page 24 of the JVC MX-J552 user manual — Enable or disable Recording Timer after you have specified settings
Page 24 · click to enlarge
Page 24
Diagram . .
Diagram . .

4 Set the time you want the device to be enabled. 1) Press 4 or ¢ to set the right hour and then press SET. 2) Press 4 or ¢ to set the minutes and then press SET. .OFF TIME .At the same time, it will be displayed for 2 seconds and then the time setting mode for switching off is switched on. 5 Set the time when you want to turn off the device (set on standby). 1) Press 4 or ¢ to set the right hour and then press SET. 2) Press 4 or ¢ to set the minutes and then press SET. The station selection mode is enabled. 6 Select the desired transmitter. 1) Press 4 or ¢ to select the bandwidth (JOTUNER FM. or GOTUNEr AM.) and then press SET. 2) Press 4 or ¢ to select the channel number and then press SET. The REC (Recording Timer) indication stops blinking and burns continuously. The settings you specify will be displayed in the correct order on the display. 7 Press to switch off the device (to be set on standby), if necessary.

With Sleep Timer you can fall asleep with music. You can set the Sleep Timer when the device is enabled.

This is how the Sleep Timer works The device will automatically be switched off when the specified time span has expired.

Only on the remote control: 1 Press DEEP. The time to disable is displayed and the SLEEP indication on the display starts blinking. • Every time you press this button, the following times are displayed:

20 30 60 90 120

2 Wait about 5 seconds after you have specified the desired duration. The SLEEP indication stops blinking and burns continuously.

If you want to check how much time is left before the device is switched off, Press SLEEP once, and the remaining time will be displayed for about 5 seconds. If you want to change the time of disable, Press DEEP a few times until the desired duration is displayed on the display. If you want to cancel the specified setting, Press SLEEP a few times until the DEEP indication is disabled. • The Sleep Timer will also be cancelled when you turn off the device.

If you want to listen to another source while recording Press REC START/STOP to stop the recording. If you don't do this, you can't specify another source.

The priority of time functions

Since each time function can be set separately, you may wonder what happens if the settings for these functions overlap. Here are some examples. • Recording Timer takes precedence over Daily Timer and Sleep Timer. If Daily Timer is set to be in function at a time when Recording Timer has been in operation, Daily Timeer will not be enabled at all.

Enable or disable Recording Timer after you have specified settings

1 Press CLOCK/TIMER several times until .RECO-PATCH is displayed on the display. 2 If you want to disable the Recording Timer, press CANCEL. The REC (Recording Timer) indication on the display is disabled. The Recording Timer has been cancelled, but the settings for the Recording Timer are kept in memory. If you want to enable the Recording Timer, press SET. The REC (Recording Timer) indication on the display is illuminated. The settings you specify will be displayed in the correct order on the display, so that you can confirm them.

6:00 7:30 7:00 6:30

Not working.

If Recording Timer is set at a time when Sleep Timer has been in function, Sleep Timeer does not work (the SLEEP indication is not disabled).

6:00

7:00 6:30

7:30

Not working.

Show 6 more labels / short text on this page
Cancelled · Cancelling · Recording Timer · Daily Timer• Recording Timer · Sleep Timer
Page 25 of the JVC MX-J552 user manual — Works with CD-ROMs
Page 25 · click to enlarge
Page 25
Diagram . .
Diagram . .

If you want to get the best out of your device, keep the CDs and cassettes clean and the mechanism.

Works with CD-ROMs

Cassette-tapes, cassette-taped or similar articles

  • Remove the CD from the cover by holding it at the edges and pressing gently on the hole in the middle.
  • Never touch the shiny surface of the CD or bend it.
  • After use, you should return the CD to the cover in order to avoid warping.
  • When the tape is loose in the cassette, pull it tight again by turning a pencil into one of the recesses in the middle.
  • When the tyre is loose, it can stretch, break or get caught in a cassette.
  • Don't ever touch the tape yourself.
  • Make sure you do not scratch the surface of the CD when you put it back in the cover or box.
  • Avoid exposure to direct sunlight, extreme temperatures and moisture.
  • Never store tyres in these places: . . In dusty spaces .

Clean the CD Rub the CD with a soft cloth, in a straight line from the middle to the edge.

heat . . In humid spaces .

NEVER use solvents such as vinyl plate cleaning agents, sprays, thinner or gasoline to clean the CDs.

Page 26 of the JVC MX-J552 user manual — Use the time functions
Page 26 · click to enlarge
Page 26
Diagram . .
Diagram . .

If you have any problems with this device, first check this list for a possible solution before calling the repair service. If you cannot solve the problem using the suggestions given here or if the device is physically damaged, call an expert (for example the dealer) for a repair.

I can't hear a sound.

Connections are not correct or unlocked.

Check all connections and improve them. (See pages 6 to 8.)

Broadcasts are hard to hear because of noise.

  • Antennas are not connected.
  • Connect the antennas firmly in the right way.
  • Move the AM (LW/MW) antenna.
  • The AM (LW/MW) antenna is too close to the device.
  • The FM antenna is not well folded and placed.
  • Expand the FM antenna to its best position.

Discontinue sound.

The CD is scratched or contaminated.

Clean or replace the CD. (See page 25.)

The CD drawer cannot be opened or closed.

  • The power cord isn't connected.
  • The drawers are locked.
  • Put the power cord in the wall contact.
  • Unlock the CD load. (See page 17.)

The CD is not playing.

The CD is upside down.

Place the CD with the label upwards.

The cassette holders can't open.

Power supply from the power cord is switched off while the tire was running.

Turn on the device.

Recording is not possible.

Lips on the back of the cassette have been removed.

Cover the cutouts with tape.

Functions are off.

The built-in microprocessor may be defective due to external electrical interference.

Unplug the power cord and plug it back into the wall contact.

The remote control isn't working.

  • The path between the remote control and sensor on the device is blocked.
  • The batteries are dead.
  • Remove the obstacle.
  • Replace the batteries.

Symptom · Cause · Action

Page 27 of the JVC MX-J552 user manual — Description of the PTY codes:
Page 27 · click to enlarge
Page 27
Diagram . .
Diagram . .

This section of the manual is for models equipped with RDS functions (the CA-MXJ750R, CA- MXJ552R and CA-mXJ550R).

Description of the PTY codes:

FINANCE: Exchange reports, trade, economy etc.

CHILDRENProgramme performance targets for young people

NEWS: News.

target group.

AFFAIRS: Recent news programme that highlights news facts in conversations or analyses.

SOCIAL A: Programs on sociology, history, geography, psychology and society.

INFO: Programs intended to provide information, in the broadest sense.

RELIGION: Religious program performances.

PHONE IN: Programs where the public can express their opinion, either by telephone or in a public forum.

SPORT: Sports program.

EDUCATION: Educational programme "s'.

DRAMA: All the hearing games and radio series. CULTURE: Programme activities relating to national or regional culture, including language, theatre etc.

TRAVEL: Travel information. LEISURE: Programme activities on recreational activities.

JAZZ: Jazz music.

SCIENCE: Programme activities on science and technology.

COUNTRY: Country music.

VARIED: This is mainly used for spoken program essays such as quizzes, panel games and interviews with well-known people.

NATIONALContemporary popular music from the country or

region in the language of that country or region.

OLDIES: Music from the so-called "golden century" of pop music.

POP M: Contemporary commercial pop music.

ROCK MRock music.

FOLK M: Folk music.

M.O.R. M: Contemporary music.

DOCUMENT:Documentary programme performances, which are facts on

The Commission's proposal is based on the following principles:

LIGHT M: Instrumental music and vocal or coral works.

TRAFFIC: Traffic information.

CLASSICS: Performances of major classical orchestral works, symphonies, chamber music, etc.

OTHER M: Music that falls into none of the previous categories.

The classification of the PTY codes may be different for some FM transmitters than the above list.

WEATHER: Weather reports and weather forecasts.

Page 28 of the JVC MX-J552 user manual — 0,15% (WRMS)
Page 28 · click to enlarge
Page 28

Specifications

CA-MXJ750R

CA-MXJ552R/CA-MXJ550R/CA-MXJ500

Amplifier Output current (IEC 268-3/DIN) SUBWOOFERS: 65 W per channel, min. RMS, both channels driven in 6 Ω at 63 Hz with up to 0.9% total harmonic distortion. Main SPEAKERS: 20 W per channel, min. RMS, both channels

Amplifier Output current (IEC 268-3/DIN) 75 W per channel, min. RMS, both channels driven in 6 Ω at 1 kHz with up to 0.9% total harmonic distortion.

Audio input sensitivity/impedance (at 1 kHz)

AUX420 mV/50 k Ω

Drived in 6 Ω at 1 kHz with up to 0.9% total harmonic distortion.

Digital OutputCD OPTICAL DIGITAL OUTPUT
Signal wave length660 nm Output level: .a.15 dBm to .b.12 dBm

(at 1 kHz measured by the HEAD-LISSING PRESSURES)

Speakers/impedance6 Ω – 16 Ω
AUX460 mV/50 k Ω
Digital OutputCD OPTICAL DIGITAL OUTPUT

Tuner FM range: 87,50 MHz . .

Signal wave length660 nm Output level: .a.15 dBm to .b.12 dBm
Speakers/impedance6 Ω – 16 Ω

Tuner FM range: 87,50 MHz . .

CD Player CD Capacity3 cdvs Dynamic range: 85 dB Signal-to-noise ratio: 90 dB Wow and flutter: Unmeasurable
CD Player CD Capacity3 cdvs Dynamic range: 85 dB Signal-to-noise ratio: 90 dB Wow and flutter: Unmeasurable

Normal (type I): 50 Hz .14,000 Hz Cro2 (type II): 50Hz .14,000 Hz Metal (type IV): 50hz

0,15% (WRMS)

Normal (type I): 50 Hz .14,000 Hz Cro2 (type II): 50Hz .14,000 Hz Metal (type IV): 50hz

General Power supply: AC 230 V , 50 Hz Power consumption: 95 W (in operation) 14 W (on standby) Dimensions (approximately): 265 mm x 335 mm x 368 mm (W/H/D) Mass (approximately: 9.7 kg

0,15% (WRMS)

General Power supply: AC 230 V , 50 Hz Power consumption: 120 W (in operation) 15 W (on standby) Dimensions (approximately): 265 mm x 335 mm x 368 mm (W/H/D) Mass (approximately: 9,9 kg

Included accessories See page 6.

Design and specifications may be modified without prior notice.

Included accessories See page 6.

Design and specifications may be modified without prior notice.

Audio import sensitivity/impedance · Cassettedeck Frequency response · Cassettedeck Frequency response

Ask about the JVC MX-J552

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the JVC MX-J552

Be the first to ask — other owners or our team will answer.

Original document

JVC MX-J552 manual PDF

28 pages·1014 KB·Audiosystem·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…