EN
IKEA logo
Official user manual

Ikea HARMONISK

56 pages·4.6 MB·Kitchen Range Hood·PDF·ENNLJA
Ikea HARMONISK
Table of Contents 17 sections HARMONISK · GB · DE · FR · … ShowHide
Page 1 of the Ikea HARMONISK user manual — GB
Page 1 · click to enlarge
Page 1

HARMONISK

GB

DE

FR

IT

Page 2 of the Ikea HARMONISK user manual — HARMONISK
Page 2 · click to enlarge
Page 2
Page 2 of the Ikea HARMONISK user manual — HARMONISK
Page 3 of the Ikea HARMONISK user manual — ENGLISH 4 DEUTSCH 15 FRANÇAIS 26 ITALIANO 43
Page 3 · click to enlarge
Page 3

ENGLISH 4 DEUTSCH 15 FRANÇAIS 26 ITALIANO 43

Page 7 of the Ikea HARMONISK user manual — LED 1 LED 2
Page 7 · click to enlarge
Page 7

Product description

1 Chimney.

2 Control Panel.

3 Light.

4 Panel.

5 Grease Filter (hidden by the panel).

Control panel

Excluding the electronics Touch the button A for 3 seconds. The hood command electronics will be excluded. This function can be useful during the product cleaning operations. Just repeat the operation to reinsert the electronics.

LED 1 LED 2

C D E F B A

To select the functions of the hood just touch the commands.

If the hood fails to operate correctly, briefly disconnect it from the mains power supply for almost 5 sec. by pulling out the plug. Then plug it in again and try once more before contacting the Technical Assistance Service. B LOW-SPEED BUTTON (suction power).

A BUTTON ON/OFF (stand-by)

Functions included:

Motor OFF Touch briefly to switch the motor off.

Reset filter alarm signals In functioning mode, after carrying out filter maintenance, touch the button until hearing the sound signal. The flashing LED 1 (grease filter) or 2 (carbon filter) stops flashing.

When flashing it indicates the need to wash the grease filter. C MEDIUM-SPEED BUTTON (suction

power). When flashing it indicates the need to wash or replace the carbon filter. This signal is normally deactivated.

Page 8 of the Ikea HARMONISK user manual — DO NOT USE ALCOHOL
Page 8 · click to enlarge
Page 8

To activate the alarm, disable the electronic by touching the A button for 3 seconds. Next, simultaneously touch buttons B and C for 3 seconds until hearing the sound signal: at first, only LED 1 will flash and then both LEDs 1 and 2 will flash to indicate the activation. Repeat the procedure to deactivate the alarm: at first, LED 1 and 2 will flash and subsequently only LED 1 to indicate deactivation. If you touch simultaneously buttons B and C for 1 second you

can verify which filter alarm mode is activated: LED 1 flashing alone for grease filter alarm mode, or LEDs 1 and 2 flashing for grease filter and carbon filter alarm mode. D HIGH-SPEED BUTTON (suction power).

E INTENSIVE SPEED BUTTON (suction

power) - duration 5 minutes - touch again to return to previous setting. F LIGHT BUTTON ON/OFF

Cleaning and maintenance

and must therefore be opened each time access to the grease filters and the inside of the hood is required (e.g. to replace the carbon filters). Opening: Pull the panel downwards. Closing: The panels must be fixed to the appropriate pins on the surface of the hood.

power supply.

To clean the grease filter The metal grease filter has an unlimited life and must be washed once a month by hand or dishwasher at low temperature and with a short cycle. With cleaning in a dishwasher the grease filter may become dull; this does not effect its filtering capacity.

Grease filter maintenance: 1. Disconnect the hood from the electric power supply. 2 Remove the grease filters: pull the spring release handle downwards, then remove the filter. 3. After cleaning the grease filter, remount in reverse order ensuring the entire extraction surface is covered. The front side is indicated by the writings “Front” printed on the hidden side of the panel.

Perimeter suction panel The suction panel must be cleaned with the same frequency as the grease filter. Use a damp cloth and a soft liquid detergent. Do not use products containing abrasives.

DO NOT USE ALCOHOL

The panel normally covers the grease filters,

Page 9 of the Ikea HARMONISK user manual — Cleaning and maintenance
Page 9 · click to enlarge
Page 9

The filter will retain its odour-absorbing capacity for three years, after which it will have to be replaced.

Ikea HARMONISK — Cleaning and maintenance diagram (page 9)
Fig. 1 · Cleaning and maintenance
Ikea HARMONISK — Cleaning and maintenance diagram (page 9)
Fig. 2 · Cleaning and maintenance

Charcoal filter maintenance (if the hood is installed in recirculation mode) 1. Unplug the appliance or disconnect the power supply. 2. Remove the panel and grease filters 3. Hook the carbon filter firstly to the metal tab at the back on the hood. 4. Fix it at the front with the two knobs. 5. Refit the grease filters and panel.

LED light The hood is equipped with a lighting system based on LED technology. The LEDs guarantee an optimum lighting, a duration up to 10 times as long as the traditional lamps and allow to save 90% electrical energy.

Unlike traditional charcoal filters, this charcoal filter can be washed and reactivated. With normal hood use, the filter should be cleaned once a month. The best way to clean the filter is in a dishwasher at the highest temperature possible, using a normal dishwasher detergent. To avoid particles of food or dirt settling on the filter during washing and giving rise to unpleasant smells, it is advisable to wash the fi lter on its own. After washing, dry the filter in the oven at 100°C for 10 minutes to reactivate it.

For replacement, contact the technical service.

Page 10 of the Ikea HARMONISK user manual — Cleaning and maintenance
Page 10 · click to enlarge
Page 10

What to do if ...

ProblemPossible causeSolution The appliance does not workThere is no mains electrical powerCheck for the presence of mains electrical power. Turn off the appliance and restart it to see if the faults persists. The appliance is not connected to the electrical supplyCheck if the appliance is connected to the electrical supply. Turn off the appliance and restart it to see if the faults persists. The hood’s suction level is not enoughThe suction speed is too lowCheck the suction speed and adjust as necessary. The metal filters are dirtyCheck that the filters are clean If not, clean the filters in the dishwasher. The air vents are obstructedCheck the air vents for any obstructions and remove as necessary. The light does not workThe light bulb is brokenFor replacement, contact the technical service. LED 1 blinksGrease filters are dirty.Perform maintenance of grese filter as described in the relevant paragraph. LED 2 blinksCarbon filter is dirty.Perform maintenance of carbon filter as described in the relevant paragraph.
Page 11 of the Ikea HARMONISK user manual — Cleaning and maintenance
Page 11 · click to enlarge
Page 11

Before contacting the After-sales service: Switch the appliance on again to see if the problem has disappeared. If not, switch it off again and repeat the operation after an hour. If your appliance still does not work properly after carrying out the checks listed in the troubleshooting guide and switching the appliance on again, contact the After- sales service, clearly explaining the problem and specifying:

  • the type of fault;
  • the model;
  • the type and serial number of the appliance (given on the rating plate);
  • the Service number (the number after the word SERVICE on the rating plate inside the appliance).
Ikea HARMONISK — Cleaning and maintenance diagram (page 11)
Fig. 3 · Cleaning and maintenance
Dimensions - Internal (mm)Width850 mm Heightmax 1420 Depth470 Airflow max - Exhaust (m3/h)646 Noise max - Exhaust (dBa)68,4 Airflow max - Recirculating (m3/h)585 Noise max - Recirculating (dBa)72,1 Total Power (W)262,0 Lamps1 x 7W Weight (Kg)18,7 Installation minimun height dimensions (cm)gas or combi cookers70 electric cookers60

The technical information is situated in the rating plate on the internal side of the appliance.

Ikea HARMONISK — Cleaning and maintenance diagram (page 11)
Fig. 4 · Cleaning and maintenance
Page 12 of the Ikea HARMONISK user manual — IKEA GUARANTEE
Page 12 · click to enlarge
Page 12

Environmental concerns

Disposal of packing The packing material is 100% recyclable and is marked with the recycle symbol . The various parts of the packing must therefore be disposed of responsibly and in full compliance with local authority regulations governing waste disposal.

  • Scrapping of household appliances
  • This appliance is manufactured with recyclable or reusable materials. Dispose of it in accordance with local waste disposal regulations. Before scrapping, cut off the power supply cable.
  • For further information on the treatment, recovery and recycling of household electrical appliances, contact your competent local authority, the collection service for household waste or the store where you purchased the appliance.

Scrapping the product - This appliance is marked in compliance

with European Directive 2002/96/EC, Waste Electrical and Electronic Equipment (WEEE). - By ensuring this product is disposed

Declaration of conformity n • This appliance has been designed, manufactured and marketed in compliance with: - safety objectives of the “Low Voltage”

of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.

Directive 2006/95/CE (which replaces 73/23/CEE and subsequent amendments); - the protection requirements of Directive

The symbol on the product or on the accompanying documentation indicates that it should not be treated as domestic waste but must be taken to an appropriate collection centre for the recycling of electrical and electronic equipment.

“EMC” 2004/108/EC.

Electrical safety of the appliance can only be guaranteed if it is correctly connected to an approved earthing system.

IKEA GUARANTEE

How long is the IKEA guarantee valid? This guarantee is valid for five (5) years from the original date of purchase of your appliance at IKEA, unless the appliance is named LAGAN in which case two (2) years of guarantee apply. The original sales receipt, is required as proof of purchase. If service work is carried out under guarantee, this will not extend the guarantee period for the appliance.

Which appliances are not covered by the IKEA five (5) years guarantee? The range of appliances named LAGAN and all appliances purchased in IKEA before 1st of August 2007.

Who will execute the service? IKEA service provider will provide the service through its own service operations or authorized service partner network.

Page 13 of the Ikea HARMONISK user manual — Environmental concerns
Page 13 · click to enlarge
Page 13

What does this guarantee cover? The guarantee covers faults of the appliance, which have been caused by faulty construction or material faults from the date of purchase from IKEA. This guarantee applies to domestic use only. The exceptions are specified under the headline “What is not covered under this guarantee?” Within the guarantee period, the costs to remedy the fault e.g. repairs, parts, labour and travel will be covered, provided that the appliance is accessible for repair without special expenditure. On these conditions the EU guidelines (Nr. 99/44/EG) and the respective local regulations are applicable. Replaced parts become the property of IKEA.

  • Accidental damage caused by foreign objects or substances and cleaning or unblocking of filters, drainage systems or soap drawers.
  • Damage to the following parts: ceramic glass, accessories, crockery and cutlery baskets, feed and drainage pipes, seals, lamps and lamp covers, screens, knobs, casings and parts of casings. Unless such damages can be proved to have been caused by production faults.
  • Cases where no fault could be found during a technician’s visit.
  • Repairs not carried out by our appointed service providers and/or an authorized service contractual partner or where non-original parts have been used.
  • Repairs caused by installation which is faulty or not according to specification.
  • The use of the appliance in a nondomestic environment i.e. professional use.
  • Transportation damages. If a customer transports the product to his home or another address, IKEA is not liable for any damage that may occur during transport. However, if IKEA delivers the product to the customer’s delivery address, then damage to the product that occurs during this delivery will be covered by IKEA.
  • Cost for carrying out the initial installation of the IKEA appliance. However, if an IKEA appointed Service Provider or its authorized service partner repairs or replaces the appliance under the terms of this guarantee, the appointed Service Provider or its authorized service partner will reinstall the repaired appliance or install the replacement, if necessary. These restrictions do not apply to fault-free work carried out by a qualified specialist using our original parts in order to adapt the appliance to the technical safety specifications of another EU country.

What will IKEA do to correct the problem? IKEA appointed Service Provider will examine the product and decide, at its sole discretion, if it is covered under this guarantee. If considered covered, IKEA Service Provider or its authorized service partner through its own service operations, will then, at its sole discretion, either repair the defective product or replace it with the same or a comparable product.

  • What is not covered under this guarantee?
  • Normal wear and tear.
  • Deliberate or negligent damage, damage caused by failure to observe operating instructions, incorrect installation or by connection to the wrong voltage, damage caused by chemical or electrochemical reaction, rust, corrosion or water damage including but not limited to damage caused by excessive lime in the water supply, damage caused by abnormal environmental conditions.
  • Consumable parts including batteries and lamps.
  • Non-functional and decorative parts which do not affect normal use of the appliance, including any scratches and possible color differences.
Page 14 of the Ikea HARMONISK user manual — SAVE THE SALES RECEIPT!
Page 14 · click to enlarge
Page 14

How country law applies The IKEA guarantee gives you specific legal rights, which cover or exceed all the local legal demands. However these conditions do not limit in any way consumer rights described in the local legislation.

How to reach us if you need our service

Please refer to the last page of this manual for the full list of IKEA appointed After Sales Service Provider and relative national phone numbers.

Area of validity For appliances which are purchased in one EU country and taken to another EU country, the services will be provided in the framework of the guarantee conditions normal in the new country. An obligation to carry out services in the framework of the guarantee exists only if the appliance complies and is installed in accordance with: - the technical specifications of the country in which the guarantee claim is made; - the Assembly Instructions and User Manual Safety Information.

In order to provide you a quicker

service, we recommend to use the specific phone numbers listed on this manual. Always refer to the numbers listed in the booklet of the specific appliance you need an assistance for. Please also always refer to the IKEA article number (8 digit code) and 12 digit service number placed on the rating plate of your appliance.

SAVE THE SALES RECEIPT!

It is your proof of purchase and required for the guarantee to apply. The sales receipt also reports the IKEA name and article number (8 digit code) for each of the appliances you have purchased.

  • The dedicated AFTER SALES for IKEA appliances Please don’t hesitate to contact IKEA appointed After Sales Service Provider to:
  • make a service request under this guarantee;
  • ask for clarifications on installation of the IKEA appliance in the dedicated IKEA kitchen furniture;
  • ask for clarification on functions of IKEA appliances. To ensure that we provide you with the best assistance, please read carefully the Assembly Instructions and/or the User Manual before contacting us.

Do you need extra help? For any additional questions not related to After Sales of your appliances please contact your nearest IKEA store call centre. We recommend you read the appliance documentation carefully before contacting us.

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
The appliance does not workThere is no mains electrical powerCheck for the presence of mains electrical power. Turn off the appliance and restart it to see if the faults persists. p.10
The appliance does not workThe appliance is not connected to the electrical supplyCheck if the appliance is connected to the electrical supply. Turn off the appliance and restart it to see if the faults persists. p.10
The hood’s suction level is not enoughThe suction speed is too lowCheck the suction speed and adjust as necessary. p.10
The hood’s suction level is not enoughThe metal filters are dirtyCheck that the filters are clean If not, clean the filters in the dishwasher. p.10
The hood’s suction level is not enoughThe air vents are obstructedCheck the air vents for any obstructions and remove as necessary. p.10
The light does not workThe light bulb is brokenFor replacement, contact the technical service. p.10
LED 1 blinksGrease filters are dirty.Perform maintenance of grese filter as described in the relevant paragraph. p.10
LED 2 blinksCarbon filter is dirty.Perform maintenance of carbon filter as described in the relevant paragraph. p.10

Ask about the Ikea HARMONISK

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Ikea HARMONISK

Be the first to ask — other owners or our team will answer.

Original document

Ikea HARMONISK manual PDF

56 pages·4.6 MB·Kitchen Range Hood·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…