Instruction/ maintenance manual of the product 9456 Bloomfield
Go to page of 30
721 OWNERS M A NUAL for POST-MIX DISPENSERS MODELS : 9454 9456 Includes: Installation Operation Use & Care Servicing Instructions p/n 83188 Rev. C ECN- 12 738 M 721 04 0811 cps Model 9456 3-Flavor.
NOTE: For your protection, please note that equipment in this shipment was carefully inspected and packaged b y skilled personnel before le aving the factory. Upon acceptance of this shipm ent, the transportation company assumes full responsibility for its safe delivery.
MODEL STYLE VOLT S WAT TS AMP S 1ø POWER SUPPLY CORD 9454 2-FLAVOR 120 VAC 1ø 1500 W 12.5A 9456 3-FLAVOR NEMA 5-15P 1 TABLE OF CONTENTS SPECIFIC ATIONS Thank You for pu rchasing th is Bloomfield Industries appliance.
FE AT U R E S AN D OP E R AT I N G CO N T R O L S 2.
FEATURES AND OPER ATING CONTROLS (continued) 3 ITEM DESCRIPTION COMMENTS 1 WA TE R TA NK 2 WATER LEVEL PROBES SENSE HIGH AND LOW WATER LEVE LS 3 DISPENSER W ATER SUPPLY TUBES 9456 SHOWN.
FEATURES AND OPERATING CONTROLS (continued) 4 INTERNAL COMPONENTS ITEM DESCRIPTION COMMENTS 30 W HIPPER MOTORS 31 AUGER MOTOR 32 VENT "TEE" 33 DISPENSE SOLENOIDS 34 TEMPERATURE CONTROL THERM.
PRECAUTIONS A ND GENERAL INFORM A TION 5 WARNING: ELECTRIC SHOCK HAZARD All servicing requiring access to non-insulated components must be performed by qualified service personnel. Do not open any access panels which requ ire the use of tools. Failure to heed this warning can result in electrical s hock.
INSTALL ATION 6 RE A D THIS CAREFULL Y BEFORE ST A RTING TH E INST A LLA TION Unpack the unit. Inspec t all com ponents for completeness and condition. Ensure that all packing materials have been removed from the unit. Read all instructions in this m anual carefully before st arting installation of this f ryer.
INSTALLATION (continued) 7 WARNING: SHOCK HAZARD Brewer must be properly grounded to prevent possible shock hazard. DO NOT assume a plumbing line will provide suc h a ground . Electrical shock will cause death or serious injury. IMPORTANT: Supply power mu st match nameplate for voltage and phase.
OPERATION 8 OPERATING MODES IMPORTANT: Dispensers used to dispense both hot and cold drinks, must be connected to a co ld wat erline . Portab l e un its ha ve no mean s of providing t wo diff erent wa ter tem per atures, INITIAL SET-UP: WATERLINE-CONNECTED DISPENSERS 1.
OPERATION (continued) 9 INITIAL SET-UP: PORTABLE DISPENSERS 1. Turn PO W ER switch OFF . Turn W ATERLINE / PORTABLE switch to PORTABLE Turn HE ATER switch OFF . Turn COLD/HOT / HOT/HOT switch to HOT/HOT Turn DISPE NSE / FLUSH switch to flush 2. Add water to tank.
OPERATION (continued) NOTE : Hoppers and motors for various products are essenti ally identical. In a cold / hot dispensing mode, the cold product must be placed in the left dispen ser only . Otherwise, product m ay be place d in and dispen sed fr om either hopper.
CLEANING I NSTRUCTIONS PROCEDURE: Daily Cleaning - Dispenser PRECAUTIONS: Avoid spla shing hot water f rom tank FREQUENCY: Daily TOOLS: Mild Detergent, Clean So ft Cloth or S ponge 1. Open f ront door. Turn the DISPENSE / FLUSH switch to the FLUSH position 2.
CLEANING I NSTRUCT IONS (continued) 12 PROCEDURE: Weekly Cleaning & Sanitizing PRECAUTIONS: Disconnect disp enser fro m electric pow er and allo w to cool. Av oid splashing hot water f rom tank FREQUENCY: Weekly TOOLS: Small Flat-Blade Screwdriver Bott le Brush of Stiff Bristle Brush Mild D etergent, Clean Sof t Cloth or Sponge 1.
CLEANING INSTRUCTIONS (continued) 13 PROCEDURE: Weekly Cleaning - Hoppers PRECAUTIONS: None FREQUENCY: Weekly, or as necessary TOOLS: Mild Detergent, Clean Soft Cloth or Sponge 1. W hen refilling hopper, insp ect auger spring, star wheel and inside of hopper for a "crusty" buildup.
TROUBLESHOOTING SUGGEST IONS 14 CAUTION: SHOCK HA ZA RD Opening access panels may expose un insulated electrical components. Disconnect dispenser from electrical pow e r before removing any panel. Do not attempt to repair or replace components without first unplugging the pow er cord.
TROUBLESHOOTING SUGGESTIONS (continued) 15 PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION WATER DRIPS OR FLOWS OUT SPOUT WITH POWER OFF Foreign particles inside dispense valve Remove valve coil, gently lif .
SERVICING INSTRUCTIONS 16 CAUTION: SHOCK HAZARD Opening access pan els may expose uninsu lated electr ical components. Disconnect dispenser f rom electrical power before removing any panel. Do not attemp t to repair or replace components without first unplugging the po wer cor d .
SERVICING INSTRUCTIONS 17 COLD WATE R A DJUSTMENT The dispenser can dispense both hot and cold beverage on ly when connected t o a wat er line with the water suppl y valve open. Cold product is available from the left dispenser only, and only when the COLD/HOT, HOT/ HO T selector switch is set in COLD/HOT position.
SERVICING INSTRUCT IONS (continued) 18 REPLACE PRODUCT DELIVERY AUGER Before at tempting majo r changes, such a s installi ng a diff erent rate product delivery auger, consult your product supplier for recommendations as to the required ratio product weight per volume of water.
SERVICING INSTRUCTIONS (continued) 19 CAUTION: CHEMICA L BU RN HA ZA RD Deliming chemicals may be caustic. Wear appropriate protective gloves and goggles during this procedur e. Never siphon deliming chemicals or solutions by mouth. This operation sh ou ld on l y be performed by qualified and experienced service personnel.
EXPLODED VIEWS 20.
EXPLODED VIEWS (continued) 21.
EXPLODED VIEWS (continued) 22.
EXPLODED VIEWS (continued) 23.
EXPLODED VIEWS (continued) 24.
25 SERVICE PARTS LIST Nut w/ Lockwasher S0311 Nut, Nylon 1/2-13 S0313 Nut, Hex SS 6-32 x 5/15 S0316 Nut, NS 4-40 SS S0343 Screw SS 6-32 x 1/4 S0434 Screw SS 6-32 x 3/8 S0435 Screw SS 10-32 x 3/8 S0444 Washer SS .187 ID S0514 Washer SS .500 ID S0518 Washer Nylon .
WIRING DIA GRAM 26 9454.
WIRING DIA GRAM 27 9456.
Bloo mf iel d Indu st ri es, Inc . Division of Carrier Co mmercial Refrigeration In US and Can ada T elep h one: 775 -689- 5700 Fa x: 888 -492- 2783 Fa x: 800 -356- 5142 () websi te: www .
An important point after buying a device Bloomfield 9456 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bloomfield 9456 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bloomfield 9456 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bloomfield 9456 you will learn all the available features of the product, as well as information on its operation. The information that you get Bloomfield 9456 will certainly help you make a decision on the purchase.
If you already are a holder of Bloomfield 9456, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bloomfield 9456.
However, one of the most important roles played by the user manual is to help in solving problems with Bloomfield 9456. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bloomfield 9456 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
