Instruction/ maintenance manual of the product SC-7E Blodgett
Go to page of 18
1 SC-7E and SC-10E ELECTRIC CONVECTION STEAMER INSTALLATION – OPERATION – MAINTENANCE BLODGETT OVEN COMPANY www.blodgett.com 44 Lakeside Avenue, Burlington, Vermont 05 401 USA Telephone (800) 33 1.
2 IMPORTANT NOTES FOR INSTALLATION AND OPERATION This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
3 TABLE OF CONTENTS DESCRIPTION PAGE 1.0 Service Connections ............................................................................................... 4 2.0 Installation Instructions...............................................................
4 1.0 SERVICE CONNECTIONS.
5 2.0 INSTALLATION INSTRUCTIONS This steamer was inspected before leaving the factory. The transportation company assumes full responsibility for safe delivery upon acceptance of the shipment. Immediately after unpacking the steamer, check for possible damage.
6 ELECTRICAL CONNECTION WARNING: Electrical grounding connections must comply with applicable portions of the National Electrical code and/or other local electric codes. WARNING: Disconnect the power supply to the appliance before cleaning or servicing.
7 DRAIN CONNECTIONS The drain connection must be 1" (25 mm) IPS down, preferably with one or two elbows only, maximum length 6 feet (1830 mm) and piped to an open gap type drain (Figure 1). Drain pipe should be either iron or copper. DO NOT use PVC pipe – PVC pipe may lose its rigidity or glue may fail.
8 VENT HOOD Some local codes may require the steamer to be located under an exhaust hood. Information on the construction and installation of ventilating hoods may be obtained from NFPA Standard No. 96, Vapor Removal from Cooking Equipment , (latest edition).
9 3.0 OPERATION WARNING: Live steam and accumulated hot water in the compartment may be released when the door is opened. WARNING: An obstructed drain can cause personal injury or property damage. CONTROLS Main Power Switch ON - The boiler will automatically fill and begin heating to the preset temperature.
10 3.0 OPERATION (Continued) BEFORE FIRST USE Clean the protective oils from all surfaces of the steamer. Use a non-corrosive, grease dissolving commercial cleaner, following manufacturer’s directions. Rinse thoroughly and wipe dry with a soft clean cloth.
11 CONSTANT STEAM FEATURE, (OPTIONAL) A switch has been added to control this feature. It is located below the timer under the heading “COOKING MODE”. TIMED COOKING T he switch must be positioned to the right, towards the heading “TIMED COOKING”.
12 COOKING HINTS Your steamer efficiently cooks vegetables or other foods for immediate serving. Steam cooking should be carefully time controlled. Keep hot food holding-time to a minimum to produce the most appetizing results. Prepare small batches, cook only enough to start serving, then cook additional amounts to meet demand.
13 4.0 CLEANING WARNING: DO NOT use cleaning agents that are corrosive. WARNING: Disconnect the power supply to the appliance before cleaning or servicing. At the end of each day, or between cooking cycles if necessary... Turn main power switch OFF. Remove pans and racks from compartment and wash in sink.
14 GUIDELINES FOR MAINTAINING STAINL ESS STEEL SURFACES There are three things that can break down stainless steel and allow corrosio n to develop: 1) Abrasion; 2) Deposits and water; 3) Chlorides.
15 5.0 MAINTENANCE REMOVAL OF SCALE DEPOSITS WARNING: Read and follow instructions on the CLR bottle. Use plastic or rubber gloves to avoid skin contact. IF CLR comes in contact with skin, rinse and clear water. 1. Drain steam generator tank by setting ON/OFF switch to off.
16 6.0 TROUBLESHOOTING PROBLEM POSSIBLE CAUSES Cold water flows continuously into drain when steamer is OFF. Either or both solenoid valves are not closing. Contact your authorized service agency to repair or replace solenoid valves. Water overflowing into cooking compartment.
17 7.0 SERVICE ADJUSTMENT FOR HIGH ALTITUDE LOCATI ONS NOTICE: Contact the factory, the factory representative or local service company to perform maintenance and repairs.
18 8.0 SERVICE (Continued) WATER OVERFLOWS INTO COOKING COMPARTMENT When steamer is first turned on for the day, and the following conditions occur: - READY light does not come on after about 15 minut.
An important point after buying a device Blodgett SC-7E (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Blodgett SC-7E yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Blodgett SC-7E - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Blodgett SC-7E you will learn all the available features of the product, as well as information on its operation. The information that you get Blodgett SC-7E will certainly help you make a decision on the purchase.
If you already are a holder of Blodgett SC-7E, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Blodgett SC-7E.
However, one of the most important roles played by the user manual is to help in solving problems with Blodgett SC-7E. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Blodgett SC-7E along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
