




9 11 12 7


Option / Optional / Tilval / Optie / Opcional / Opção
3 17 16



2 ON Switching on the unit Insert the KeyCard and press ON briefly. The unit is switched on in the last op- erating mode selected and with the previously selected volume.
Switching the unit on/off using the KeyCard Insert/remove the KeyCard to switch the unit on and off. Refer also to the description of the KeyCard anti-theft system @ in the condensed instructions.
1 Disengaging the fold-down control panel Disengage the control panel to insert or remove the KeyCard and MiniDisc. To disengage the control panel, press knob 1: the control panel folds down. The control panel cannot be removed, nor should it be used a shelf. To re- engage the control panel, push it back into its original position (Arrow 3).
Switching on/off by the ignition The unit may be connected up such that it is switched on and off by the ve- hicle ignition. When the ignition is switched off, a double beep reminds you to remove the KeyCard before leaving the vehi- cle.

Switching off the unit Press ON for approx. 1 second.
The display can be adjusted for the de- sired viewing angle in order to improve legibility. Refer to “Improving the legi- bility of the display” if necessary.
Switching on whilst the ignition is off With the ignition off (and the KeyCard inserted), proceed as follows to oper- ate the unit: Press ON when the double beep sounds. The unit is switched on. The unit switches itself off automatical- ly after an hour’s use in order to pre- vent the vehicle battery from running down.
For safety reasons, the control panel must always be engaged whilst the vehicle is moving. When leaving the vehicle, open the control panel and remove the Key- Card in order to prevent theft.
Switching the sound on/off Press ON briefly. “MUTE” appears on the display when the sound is switched off. To switch the sound back on again, turn the volume knob 3.

3 Adjusting the volume Turn the knob to adjust the volume.
Menu level 1 Station keys and memory levels
Menu level 2 Adjusting radio functions


The selected value is shown on the display. When switched on, the unit plays at the preselected volume (ON VOL). ON VOL can be changed (refer to “Programming with DSC – ON VOL”).
NEXT - FM Switch between the memory levels FM I, FM II, FM T. NEXT - AM (MW, LW) Switch between the MW and LW fre- quency bands.
NEXT - FM Switch between the memory levels FM I, FM II, FM T. NEXT - AM (MW, LW) Switch between the MW and LW fre- quency bands.
4 Softkeys/display Softkey = key with variable function The functions shown in the display can be selected.
ST1 - ST6 ST1- ST6 can be used on this menu level to store radio stations on the FM levels I, II and “T”. You can store six stations each on the MW and LW bands. Store station – hold one of the station keys ST1- ST6 down until the pro- gramme can be heard again (beep). Call up station – select the frequency band. On FM, select the memory level using NEXT and press the appropriate station key briefly.
BND Select the frequency band and memo- ry level (FM I, FM II, FM T, MW, LW).
SCA - Scan a) PTY is deactivated (logo is lit normally, not in reverse video) Press SCA (Radio Scan) briefly – “SCAN” appears in the display alter- nately with the code of the sampled station. All stations on the frequency band which can be received are sam- pled briefly.
In radio mode, use TU to toggle be- tween menu level 1 and menu level 2. The system automatically returns to menu level 1 when no key has been pressed for eight seconds.
Radio mode

Press SCA for approx. 1 second (Preset Scan) – a beep sounds, “SCAN” appears in the display alternately with the code of the sampled station. The stations stored on the station keys and which can be received are sam- pled briefly.
AF on/off: Select menu level 2 using TU and press AF briefly.
TA (priority for Traffic Announce- ments) ”TP” is displayed when a traffic pro- gramme station is being received. ”TA” is displayed when priority for traf- fic programme stations is activated. Only traffic programme stations are played. Priority on/off: Press TA. Abort traffic announcement: Press TA or EXIT.
EXIT To terminate or abort the adjustment process, press the key briefly.
ENT (Enter) To accept/save the adjustments, press the key briefly.
Stopping Radio Scan/Preset Scan: Press SCA or the seek rocker again.
TS (Travelstore) Press TS to switch from any frequency band to FMT. The six strongest sta- tions are automatically stored. When they have been stored, the strongest station is selected and played.
b) PTY is activated (logo appears in reverse video on the display)
MiniDisc and CD changer mode


PTY (Programme Type) PTY turns the station keys into pro- gramme type keys. ”PTY” must first appear on the display in reverse video (Press PTY if neces- sary). A programme type such as NEWS, SPORT, POP can now be stored and selected with each station key. Call up PTY programme types using the rocker << >> and press the station key to store (hold down for approx. 2 seconds until the beep sounds).
Press SCA – the stations transmitting the selected PTY programme type are sampled briefly.
MIX, SCAN, RPT (repeat) and TPM can be selected in MiniDisc and CD changer mode by means of the corre- sponding softkeys.
MIX MiniDisc and CD tracks can be re- played in random order. You can select the following functions by pressing the MIX key:
AF (Alternative Frequency in RDS mode) If “AF” appears in reverse video in the display, the radio automatically looks for a frequency with better reception for the same station.

- MIX MD/MIX CD = Tracks on the
- REP TRCK = Repeat track - REP CD = Repeat CD (only in CD
MiniDisc or CD (in CD changer mode) are played in random order. In CD changer mode, CDs are se- lected in numerical order, tracks are replayed in random order. - MIX MAG (CD changer mode only) =
changer mode) - RPT OFF = Switches off function.
If the rocker is pressed on menu level 2, menu level 1 is automatically called up.
TPM - Track Program Memory For storing and playing preferred tracks in MiniDisc and CD changer mode. Up to 30 MiniDiscs can be man- aged in MiniDisc mode and 99 CDs in CD changer mode with a maximum of 40 tracks each. (Refer to the “TPM programming” section.)
All tracks in the magazine are played in random order. - MIX OFF = Switches off function.
SCA - Scan For sampling the tracks briefly (in CD changer mode, the tracks of all CDs).
CLR For clearing the TPM memory (refer to the “Clearing the TPM memory” sec- tion).
Starting Scan: Press SCA. The tracks are sampled briefly in ascending order. The sam- pling time can be adjusted. (Refer to “Programming with DSC – SCANTIME”.)
<</>> Up/down in steps (on FM only when AF and PTY are deactivated)
5 DPE For activating/deactivating the equaliz- er and changing the equalizer settings.
On FM only: <</>> Page through the transmission chains when AF is activated and PTY deactivated, e.g.: NDR 1, 2, 3, 4, N-JOY
Ending Scan: Press SCA. The last track selected continues playing.
Activating/deactivating the equalizer: Press DPE until the beep sounds. When the equalizer is activated, “EQ” appears in the display.
RPT - Repeat MiniDisc tracks and, in CD changer mode, CD tracks and CDs, can be re- peated. Press the RPT key to select the follow- ing functions:

MiniDisc and CD changer mode
Further functions of the rocker: Further settings available with AUD 8 DSC-MODE 7 PTY The settings are available only if the corresponding function is activated.

Select from the options using << / >>. Use
7 DSC (Direct Software Control) You can adjust programmable default settings using DSC. Further information: “Programming with DSC”.
to change the settings. The values selected are shown on the display. The last setting selected is stored automatically.
Select CD >> Up: Press briefly. << Down: Press briefly.
Particular feature of loudness: The values can be selected between LOUD 6 and LOUD OFF by means of the rocker
8 AUD For adjusting the treble, bass, balance (left/right), fader (front/rear) and loud- ness settings. Loudness = adjustment of the low- volume sounds to the human ear.
Down: Press twice or more in quick succession Replay track from beginning: Press briefly REVIEW - fast rewind (audible): Keep depressed
Leaving AUD: Press EXIT. If no change is made within eight sec- onds, AUD is automatically switched off.
Different treble, bass and loudness settings can be stored for the FM, AM, MD, AUX and TA modes.
Adjustment procedure: Select mode. Press AUD once: “BASS” and the se- lected value appear on the display.

9 DIS Selecting various display modes.
Press DIS briefly: - Name of the selected station - Currently selected frequency - PTY code A condition is that an RDS station can be received with an adequate field strength.
played - CD name, track number
TRACK 13 - Track number or VIVALDI - CD name (CD changer
: Display

mode) or CD 5 T 2 - CD number and track number
(CD changer mode) MIX - Tracks can be played in ran-
dom order SCA - Sample tracks RPT - Repeat function for MiniDisc/
NDR2 - Station name FM - Frequency band I, II, T - Memory level I, II or Travel-
CD changer mode TPM - Save and play preferred
store TP, TA - TP = Traffic Programme (traf-
tracks CLR - Clear TPM memory
Press DIS for approx. two seconds: Toggle display between time and wavelength (incl. memory level in the case of FM).
fic programme station is be- ing received) - TA = Priority for traffic pro-

gramme station is activated PTY - Programme type is activated AF - Alternative frequency with
RDS lo - Seek sensitivity can be se-
FM I, II, T - FM memory level or MW, LW - Frequency band or 00:20 - Time (time played) or 12:50 - Time
lected with DSC EQ - Equalizer is activated DISC-IN - MiniDisc is inserted
CD changer mode · Radio mode · MiniDisc mode

The ignition is off and LED ON is se- lected in the DSC menu (default facto- ry setting). Further information: “Programming with DSC, LED ON/OFF”.
Remove the KeyCard following the procedure in reverse. Important: read the information under “KeyCard anti-theft protection system”.
Switch to CD changer mode (only if a CD changer is fitted). If a CD changer is not fitted, AUX is selected. Condition: AUX ON must be selected in the DSC menu.
@ KeyCard anti-theft protection
Hold the key for MiniDisc ejection down for approx. 2 seconds: the MiniDisc is ejected.
system The KeyCard must be inserted before the unit can be operated.
Switch to MiniDisc mode.

Switch to radio mode. For switching to the FMI, FM II, TS (Travelstore), MW and LW memory levels/frequency bands.
Inserting the KeyCard To disengage the control panel, press key 1. The control panel folds down. Insert the KeyCard with the contact surface facing downwards (see dia- gram). Engage the control panel.
> Slot for MiniDisc
When the MiniDisc is inserted in the direction indicated by the arrow with the label facing upwards, it is automati- cally transported into the operating po- sition. MiniDisc play mode is selected automatically.
For safety reasons, the control panel must always be engaged whilst the vehicle is moving. When leaving the vehicle, open the control panel and remove the Key- Card in order to prevent theft.
? Visual anti-theft protection
The following conditions must be met if the LED is to flash as a visible anti- theft protection measure: The unit is switched off; The control panel is open; The KeyCard is removed;
A Eject


quick succession Replay track from beginning: Press briefly REVIEW - fast rewind (audi- ble): Keep depressed
<</>> Up/down in steps (on FM only when AF is off)
On FM only: <</>> Page through the transmission chains, if AF is on e.g.: NDR 1, 2, 3, 4, N-JOY
briefly. “MUTE” appears on the display when the sound is switched off.
MiniDisc and CD changer mode
C SRC (Source)
Select the operating mode - Radio - MiniDisc - CD changer mode (if a CD changer is
Down: Press twice or more in quick succession Replay track from beginning: Press briefly REVIEW - fast rewind (audible): Keep depressed

Telephone mute
CD changers The following CD changers can be fitted di- rectly: CDC A 06, A 072, A 08, IDC A 09. CD changers A 05 and A 071 can be fitted by means of the 7 607 889 093 adapter cable. The IDC A 09 is included with the Taxas DJ.
If a mobile phone is connected, radio and CD sound can be muted automatically when the phone is in use (telephone mute). “PHONE” then appears on the display.
Before using the car radio, read the follow- ing instructions carefully.
The traffic announcement has priority if TA is activated. Pressing the TA key causes a traffic announcement to be interrupted.
Traffic safety is of paramount importance. Always use your car radio system in a way which enables you to cope with the traffic situation.
Navigation The TravelPilot DX-N can be fitted for dy- namic navigation.
Only use accessories and spare parts ap- proved by Blaupunkt. The following Blaupunkt products can be used with this unit:
Remember that your vehicle covers 14 m a second at a speed of 50 km/h.
The unit is guaranteed in accordance with the statutory provisions of the country in which it was purchased. Irrespective of the statutory provisions, Blau- punkt guarantees the unit for twelve months. Should you have any questions concerning the guarantee, please consult your dealer. Your receipt suffices as proof of guarantee.
In critical situations, do not operate the ra- dio.
You must remain able to hear warning sig- nals, for example from police and fire serv- ice vehicles, immediately and reliably.
Remote control RC 08 (optional)

Keep the volume therefore at a reasonable level whilst driving.
Infrared remote control RC 08 permits operation of the chief functions from the steering wheel.
International hotline
Do you have any questions regarding oper- ation of the unit, or do you require further information? Simply give us a call. The international hotline and fax numbers can be found on the last page of these in- structions.
If you intend to install or modify the system yourself, read the installation and connec- tion instructions at the end of the operating instructions before doing so.
Amplifiers All Blaupunkt amplifiers.

One KeyCard is supplied with the unit.
The car radio can however also be operat- ed with a second KeyCard.
Disengage the control panel as follows
Should you lose or damage a KeyCard, you can obtain a replacement from a specialist dealer.
If you are using two KeyCards, the settings are taken from the first KeyCard. You can customize the following functions:
For safety reasons, the control panel must always be engaged whilst the vehicle is moving. When leaving the vehicle, open the control panel and remove the Key- Card in order to prevent theft.
Station key assignment, bass, treble, bal- ance and fader settings, loudness, TA (traf- fic announcement volume), beep volume, LOW-EQ, HIGH-EQ.
The last state selected such as frequency band, station setting, TA priority, AF, REG ON/OFF, SCAN-TIME, seek run sensitivity, ON VOL (volume at switch on), SHARX, is also saved.
Should a KeyCard other than that belong- ing to the unit be inserted, CARD ERR” ap- pears on the display.
Your selected settings are therefore select- ed automatically when you insert your Key- Card.
An additional KeyCard can be “taught in” whilst the unit is in operation with the first KeyCard.
The unit switches itself off after approx. 10 seconds.
Should a card other than a KeyCard be in- serted (e.g. a phonecard or credit card), “WRONG KC” is displayed for approx. 2 seconds.
To “teach in” a second KeyCard:
to select “LEARN KC”.
In this case, remove the card and insert a KeyCard for the unit. • Press ON to switch on the unit.
/

Battery positive and constant battery posi- tive are connected as described in the in- stallation instructions. The unit is switched off; the control panel is open; the KeyCard is removed; LED ON is selected in the DSC menu (default factory setting). If necessary, refer to “Programming with DSC – LED”.
Keep the car radio passport in a safe place, but not in the car.
A maximum of two KeyCards can be taught in.
Deactivating the flashing LED Select “LED OFF” in the DSC menu to de- activate the flashing LED.
If a third KeyCard is taught in, the card which is not employed for the teaching-in process of the new card automatically loses its va- lidity.
- Enter the digits (press once for
one, twice for two, etc.) << >> - Select the insertion point
The KeyCard will function perfectly only if the contacts are kept free of foreign parti- cles. Avoid touching the contacts directly with your hands.
You can use the KeyCard supplied to call up the radio passport data such as the unit name, type number (7 6 ...) and serial number on the display. Refer to “Programming with DSC – READ KC” for the procedure.
If necessary, clean the KeyCard contacts using a cotton bud soaked in alcohol.
Should the input not be correct, “CODE ERR” appears on the display. After three successive incorrect inputs, “WAIT 1h” ap- pears on the display. The unit remains in Wait mode for one hour. • Switch the unit off and on again. Repeat the teach-in process.
Should you damage or lose the KeyCard for your unit, you can teach in a new KeyCard. You can purchase the new KeyCard from your dealer. You will also require the mas- ter code for the unit, which can be found in the car radio passport.
Anti-theft protection is provided in the form of a flashing LED ? when the vehicle is parked and the KeyCard removed.
The following conditions must be met:
/ · Input errors

Enhancing the display legibility
You can select from the Radio (TU), MiniDisc (MD) and CD changer (CDC) modes.
The display can be adjusted to your pre- ferred viewing angle in order to enhance leg- ibility.
MD can be selected only if a MiniDisc is in- serted.
Proceed as follows: • Press DSC.
CDC can be selected only if a Blaupunkt A 06, A 072, A 08 or A 05, A 071 or IDC A 09 CD changer is connected and a magazine containing at least one CD is inserted.
”ANGLE” appears on the display.
Toggling between operating modes: • Press TU, MD or CDC. If TU is pressed again, menu level 2 is called up. Radio function adjustments can be made on this level. Menu level 1 is called up auto- matically if no input is made for approx. eight seconds.

The Radio Data System provides FM recep- tion with enhanced convenience.

At certain times, the broadcast stations transmit different programme content ac- cording to the region. For example, German Radio 1 serves the northern regions Schleswig-Holstein, Hamburg and Lower Saxony, and at certain times broadcasts re- gional programmes which differ in content. If you are listening to a regional programme and wish to continue to receive it, switch to REG ON in the DSC menu. If you are leav- ing the region in which the regional pro- gramme can be received, or if you wish to enjoy the full RDS service, switch to “REG OFF”. Switching REG over: • Press the DSC key and
An increasing number of radio stations now broadcast RDS information supplementary to the programme proper.
As soon as stations can be recognized, the station code appears, in some cases with indication of the region, e.g. NDR1 NDS (Niedersachsen).
”AF” then appears in reverse video on the corresponding key.
With RDS, the station keys become pro- gramme keys. You now know exactly what station you are receiving, and you can there- fore also select the desired station.

RDS offers you further advantages:
The radio may be muted briefly during the search for the channel with the best recep- tion.
repeated- ly until “REG ON/OFF” appears in the display.
The AF (Alternative Frequency) function en- sures that the best available frequency of the station being received is selected auto- matically.
If “SEARCH” appears on the display when the unit is switched on or when a stored fre- quency is called up, the unit is automatical- ly searching for an alternative frequency.
Switching AF on/off: During radio mode • Press TU: menu level 2 is called up.
”SEARCH” disappears when an alternative frequency has been found, or when the fre- quency band has been completely searched.
If the station can no longer be received with satisfactory quality: • Select a different station.
/

Station tuning
If necessary, these functions can be deacti- vated on menu level 2.
You can select from the following frequen- cy bands:
: the radio automatically looks for the next station. If
Manual tuning:
FM 87.5 – 108 MHz, MW 531 – 1602 kHz and LW 153 – 279 kHz as follows: • Press TU: menu level 2 is displayed.
is held down at the top or bottom, the seek run continues forwards or back- wards at higher speed.
Paging through the transmis- sion chains (FM only)
You can use << >> to call up stations from the region in which they can be received.
If a number of programmes in the station chain can be received, you can page through them with >> (forwards) or << (backwards), e.g. NDR 1, 2, 3, 4
Down << / >> Up/down in steps
(on FM only when AF is deactivated)
Manual tuning with << >>
You can tune manually.
Condition: AF and PTY are deactivated (the corre- sponding symbols are not lit in the display).

again after it has been muted (approx. 2 seconds), and a beep is heard. The station is now stored.
You can change between memory levels I, II and T to store stations and retrieve them again. The selected memory level appears on the display.
You can call up stored stations at the touch of a button.
You can store the six strongest FM stations in the current reception region automatical- ly in the order of field strength. This function is particularly useful on long journeys. Pro- ceed as follows: • Press TU: menu level 2 is displayed.
You can store six stations on the FM band on each memory level (I, II, T) using the sta- tion keys ST1 - ST6.
The six strongest FM stations are automat- ically stored on the “T” (Travelstore) memo- ry level. If fewer than six stations can be re- ceived, four lines appear through the mem- ory locations which are not occupied. When the procedure has been completed, the strongest station (ST 1) is selected.
You can also store six stations each on the MW and LW bands. Proceed as follows: • Press TU: menu level 2 is displayed.
or manually << >>).
Stations can also be stored manually on the Travelstore level if required (see “Storing stations”).
/

Sampling stations with Radio Scan
Changing the sampling time (Scan)
You can sample stored stations briefly on all frequency bands and on the selected FM memory level.
You can sample briefly the stations which can be received on the selected frequency band.
The sampling time can be selected between 5 and 30 seconds.
If you wish to change the duration of the sampling time, refer to “Programming with DSC – SCANTIME“.
Preset Scan can be started only when PTY is disabled (“PTY” is not lit on the display).
Radio Scan can be started only when PTY is deactivated (“PTY” is not lit on the dis- play).
You can change the sensitivity of the auto- matic seek run.
If “lo” is displayed, seek only recognizes sta- tions with good reception (low sensitivity).
If “lo” is not displayed, seek also recognizes stations with poorer reception.
To adjust the sensitivity, refer to “Program- ming with DSC – FM/AM Sens”.
Selecting sampled stations/terminating Preset Scan: • Press SCA or one of the rocker keys briefly.
Selecting a sampled station/deactivat- ing Scan: • Press SCA or one of the rocker keys briefly. If a station is not selected, Scan is switched off automatically when the seek function has passed through the complete frequency range. The station previously selected is played.
Toggling between stereo and mono (FM)
You can toggle between stereo and mono in the DSC menu. This can be useful in are- as where reception is critical. When the unit is switched on, stereo is selected automati- cally.

When reception is poor, the unit switches smoothly to mono.
NEWS CURRENT AFFAIRS INFORMATION SPORT EDUCATE DRAMA CULTURE SCIENCE VARIED POP MUSIC ROCK MUSIC EASY MUSIC LIGHT MUSIC CLASSICS OTHER MUSIC WEATHER FINANCE CHILDREN’S PROG. SOCIAL AFFAIRS RELIGION PHONE IN TRAVEL LEISURE JAZZ MUSIC COUNTRY MUSIC NATIONAL MUSIC OLDIES MUSIC FOLK MUSIC DOCUMENT
If you wish to switch to mono, refer to “Pro- gramming with DSC – STEREO/MONO”.
The state selected appears briefly on the display.
Automatic bandwidth switching (SHARX)

You can activate automatic bandwidth switching on the FM band by means of the SHARX function in the DSC menu. This is very useful when a number of stations are close together.
Interference from strong adjacent stations is largely eliminated when SHARX ON is selected (factory default setting).
You can display the last programme type selected and select a different programme type with << >>.
If necessary, refer to “Programming with DSC – SHARX”.
Use the station keys 1 - 6 to select stored programme types.
Condition: PTY is activated.
You can select the language in DSC from German, English or French (refer to “Pro- gramming with DSC - PTY LANG”).
This is an RDS service which is being im- plemented progressively by the radio sta- tions. The service enables FM stations to be selected according to a specific pro- gramme content. After selecting the pro- gramme type, you can select the stations using seek or Scan.
The programme types listed below are avail- able.
The letters in bold are the same as those on the temporary PTY display.
Activating/deactivating PTY

Prompting the station for the pro- gramme type
If no station broadcasting the selected pro- gramme type is found, “NO PTY” appears briefly on the display, and the beep sounds. The last station selected is played.
Storing the programme type
A programme type is stored on each of the keys ST1 - ST6 by the factory.
On menu level 2: • Hold PTY down for approx. 2 seconds. After the beep, the programme type of the station currently being received is displayed.
You can however store other available pro- gramme types.
You can assign a different available pro- gramme type to each memory location.
”PTY” must be displayed before you can store a different programme type. • If necessary, activate “PTY” using the PTY key.
Refer if necessary to the “Saving the pro- gramme type” section below.
If “NONE” is displayed, the station has no PTY code.
Displaying the selected programme type
b) Using the seek run rocker << >>
If PTY is activated, you can select a programme type with << >>.
Selecting the programme type
a) Using the station keys
Sampling stations with PTY-SCAN
If PTY is activated, the programme types defined by the factory can be selected by means of the keys ST 1 - ST 6.
Condition: “PTY” must be displayed. • Press SCA. The stations with this programme type which can be received are sampled briefly.
To listen to a station broadcasting this programme type:
The selected programme type appears on the display for two seconds.
. If no station broadcasting the selected pro- gramme type is found, “NO PTY” appears briefly on the display, and the beep sounds. The last station selected is played.
Deactivating PTY-SCAN: • Press SCA or the seek rocker again. Following a frequency seek run, PTY-SCAN is automatically deactivated.
To listen to a station broadcasting this programme type:
/ · /

The unit also switches automatically in CD mode to the station broadcasting the select- ed programme type within the transmission chain.
Situation:
PTY is activated, the logo appears on the display. No station broadcasting the selected pro- gramme type can be received at this time (by seek or by Scan). The unit switches back to the previous sta- tion. As soon as a station broadcasting the se- lected programme type can be received within the station chain, the unit switches to this station in radio mode for the duration of the programme.
When the PTY programme is over, the unit switches back to the source previously se- lected (radio or CD).
Example:
- Previous station: NDR 3.
- “PTY” on the display
- Seek run started
- No station with “PTY-POP” found
- Display shows “NO PTY” and
- Switches back to NDR 3 automatically
- NDR 2 is broadcasting “PTY-POP”
- Unit switches within the station chain to NDR 2 and plays it as long as the station continues to broadcast “POP”.
PTY priority · - “POP” selected

EON is the exchange of station information within a transmission chain.
Deactivating the warning tone
Select a different station with the traffic an- nouncement service: • Press the rocker or
Many FM stations transmit up-to-date traf- fic announcements for their broadcasting re- gion.
”TA” appears on the display when traffic pro- gramme priority is activated.
Activating/deactivating priority: • Radio mode: Press the TU key again to call up the function menu (not nec- essary in MD/CDC mode).
Stations which transmit traffic announce- ments transmit a signal which is recognized and evaluated by your car radio. When such a signal is recognized, “TP” (Traffic Pro- gramme) appears in the display.
In addition, some stations transmit no traf- fic announcements of their own, but offer with RDS-EON the facility of receiving traf- fic announcements from a traffic programme station within the same transmission chain.
If you are listening to MDs or CDs and you leave the broadcast range of the selected traffic programme station, the radio automat- ically looks for a new traffic programme sta- tion. If a traffic announcement station is not found within approx. 30 seconds of the start of the seek run, a beep sounds as warning at intervals of 30 seconds. To switch off the warning tone, follow the procedure de- scribed above.
If priority for traffic announcements is to be activated whilst such a station (e.g. NDR3) is being received, “TA” (priority for Traffic Announcements) must appear in the dis- play.
When a traffic announcement is broadcast, the unit switches automatically to the traffic announcement programme (in this case NDR2). The traffic announcement is played, after which the unit switches back to the pro- gramme (NDR3) previously selected.
Adjusting the volume for traffic announcements and the warning tone
Should you leave the broadcast range of a selected traffic announcement programme, a beep sounds as a warning at intervals of approx. 30 seconds. Pressing a station key on which a station without a TP signal is stored also causes a warning tone to sound.
This volume is set in the factory as a de- fault. You can however change it by means of DSC (refer to “Programming with DSC – TA VOL”).

This unit enables you to play MiniDiscs. CDs can also be played with the aid of a Blau- punkt CDC A 06, A 072, A 08, A 05, A 071 or IDC A 09 CD changer. These CD changers are available from your dealer. The IDC A 09 is included with the Taxas DJ.
A MiniDisc is inserted, “DISC-IN” appears on the display. • Press MD.

Note: Only use standard circular 12 cm diameter CDs in the CD changer. 8 cm diameter CDs or CDs with different shapes, e.g. of a butterfly or beer glass, are not suitable for playing. Such CDs present a serious risk of damage to the CD and to the drive. We can accept no liability for damage aris- ing from the use of unsuitable CDs.
Do not obstruct or assist automatic inser- tion or ejection of the MiniDisc, as the mech- anism may otherwise be damaged.
The names of the MD and individual tracks can be displayed if they are stored on the MiniDisc.
If the MiniDisc is not removed, it is drawn in again automatically after approx. 30 sec- onds.
For safety reasons, the control panel must always be engaged whilst the vehicle is moving.
Displaying the MD text
Activating/deactivating MD text

A magazine containing at least one CD must be inserted. • Press CDC. CD changer functions such as CD and track number, name, time played appear in the display.
“14:34” – Time
“00:20” – Time played Key held down: Activate/deactivate MD text.
Down: Press twice or more in quick succession Replay track from beginning: Press briefly REVIEW - fast rewind (audible): Keep depressed
The name of the CD can be displayed only if a name has been entered.
Refer to the “Assigning names to CDs” sec- tion below.
You can switch the display type over in MiniDisc and CD changer replay mode:
The rocker acts as a sequence switch: pressing it repeatedly causes several CDs or tracks to be skipped.
You can select tracks or parts of tracks and, in CD changer mode, CDs conveniently us- ing the rocker.
You can repeat a track or (in CD changer mode) a CD continually. You can select the following functions using the RPT key:
CDC mode:
- REP TRCK = Repeat track
“CD 10” – CD number
- REP CD = Repeat CD (only in CD
“TRACK 13” – Track number
Selecting a CD (CD changer mode only)
“14:34” – Time
<< / >> Select CD (CD changer mode
- RPT OFF = Deactivate function.
“00:20” – Time played
“VIVALDI” – CD name

The track or the CD is played repeatedly until you switch to “RPT OFF” using RPT.
TPM (Track Program Memory)
For storing and playing preferred tracks in MiniDisc and CD changer mode. Up to 30 MiniDiscs can be managed in MiniDisc mode and 99 CDs in CD changer mode with a maximum of 40 tracks each. TPM is ac- tive only in the mode in which the track pro- gramme was stored (MiniDisc or CD chang- er mode).

If “TPM” is shown in reverse video on the display, TPM replay is activated. All tracks on the MiniDisc or CD which were stored in the operating mode with TPM are played. If SCA (Scan) is activated in addition to TPM, only the stored tracks are sampled. TPM replay can be switched on only if tracks have been stored using TPM.
Storing tracks with TPM
A track can be stored only whilst it is being played.
To store: • Hold TPM down for approx. 1 second: “TPM PROG” appears on the display. This track has been stored.
Clearing the TPM memory
You can clear tracks stored with TPM. TPM tracks can be cleared with CLR only during replay. • Activate TPM. “TPM” appears on the display in re- verse video. In this case, “CLR” appears below TPM.
Activating/deactivating TPM replay

SCAN
. The letters of the alphabet in capitals (A-Z), the numbers 0-9 and special characters ap- pear in turn. • Move to the next underline using the rocker << >>, and select a character. Up to eight characters can be selected in this way.
MiniDisc and CD tracks can be replayed in random order. MIX is activated when “MIX” appears in reverse video on the display.
For brief sampling of the MiniDisc or CD tracks.
Starting SCAN: • Press SCA briefly: “SCAN” appears on the display. The tracks are sampled briefly in turn in as- cending order.
You can select from the following MIX func- tions:
MIX MD/MIX CD (in CD changer mode)
Tracks on the MiniDisc or the selected CD are played in random order. In CD changer mode, the remaining CDs are selected in numeric order. MIX applies to the order in which the tracks are played (random).
Ending SCAN: • Press SCA briefly. The last track selected continues playing.
SCAN is also terminated when the rocker, MIX, RPT, DSC, AUD, TU or CDC are pressed.
MIX MAG (in CD changer mode only)
CDC A 08, IDC A 09: All tracks in the mag- azine are played in random order.
to select from the magazine the next CD to which a name is to be assigned. To change a name, enter and save other characters (overwrite).
CDC A 06/072: The CDs are selected in ran- dom order; all tracks of the selected CD are then replayed in random order.
You can assign names to up to 99 CDs in CD changer mode.
MIX is deactivated. CDs are played in nu- meric order.
This name (e.g. VIVALDI) appears on the display when you have selected the corre- sponding display mode using DIS.
repeated- ly until “CDC-NAME” appears on the display.

The stored names and the TPMs of CDs can be deleted simultaneously by means of DSC-Update. You can delete the names and TPMs of the inserted CD with “CLR DISC”. You can delete the names and TPMs of all stored CDs with “CLR ALL”. A CD the stored data (name and TPM) of which are to be deleted must be replayed for this purpose.
To return to the DSC menu item “UPDATE” without deleting CD names and TPMs: • Press ENT briefly.
repeatedly until “UPDATE” appears on the display.
/ · or

The time need be adjusted manually only if an RDS station with CT (clock time) is not being received.
The unit has an internal clock which is set automatically through RDS for absolute ac- curacy.
The time can be displayed in radio and CD mode.
If you wish to correct the time manually, re- fer to “Programming with DSC – CLOCK- SET“.
A condition for correction by RDS is that an RDS transmitter with CT function (CT = clock time) is being received.
Radio mode:
The display can be toggled between time and frequency band (incl. memory level in the case of FM) as follows: • Press DIS for approx. 2 seconds.
Automatic correction of the time can be de- activated.
Correction of the hours can be deactivated by “CLK MAN/CLK AUTO” in the DSC menu. The minutes continue to be corrected.
MiniDisc/CD changer mode:
a) Automatically:
You can select from three different display modes:
This is useful if you wish to display the time of a different time zone, for example. If necessary: • Press DSC briefly and
The time is set automatically when an RDS transmitter with the “CT” (clock time) function is being received.
- Track number, time - Track number, time played - CD name, track number (CD changer
mode only).
repeatedly until “CLK MAN/ CLK AUTO” is displayed. To deactivate hours correction, select << >> “CLK MAN”.
b) Manually by means of
To toggle: • Press DIS briefly.
If the unit has been isolated from the supply voltage for a longer period, “0:00” is dis- played when the power is reconnected.
The time is corrected automatically by RDS- CT, but can also be adjusted manually.
/ · /

The sound in the vehicle is influenced deci- sively by the acoustic characteristics of the passenger compartment, substantially more than by the characteristics of the loudspeak- ers.
The parametric filters can be adjusted ex- actly without instruments.
Now read the “Tonal effect/problem” column in the table, and look for solutions under “Measure”.
In addition, you can select from seven pre- programmed equalizer settings, which are adjusted for different musical styles. Refer to the “Selecting pre-set sound settings” section.
Use the LOW EQ filter for settings in the bass and lower mid-range, and the HIGH EQ filter for the treble and upper mid-range.
The position and installation of the loud- speakers and the volume to the rear, for ex- ample of the door or parcel shelf, are how- ever also important.
The “HIGH EQ” and “LOW EQ” filters can be adjusted in the DPE menu: • Press DPE to call up the DPE main menu.
The steps required for adjustment are de- scribed in the table.
Even when suitable loudspeakers have been selected and installed properly, reso- nances in the passenger compartment may have a detrimental effect upon the sound.
Adjusting the frequency level
The instructions below represent a recom- mendation only. You can adjust the sound characteristics according to your own per- sonal preference.
repeatedly until “HIGH EQ” or “LOW EQ” appear in the display.
This can result in the bass frequencies booming or being absent, mid-frequencies encroaching excessively, musical instru- ments or voices being strongly distorted, or the sound generally being muffled.
We recommend that you use a familiar mu- sic MiniDisc for adjustment of the filters. The MiniDisc should include tracks with a range of instruments and voice. Pure electronic music is not suitable for evaluation purpos- es, since the original sound is not known.
once or several times to adjust the level (GAIN +8 ... GAIN -8).
The subjective sound impression can be improved considerably by suppression or amplification of certain frequency ranges by the car radio.
Before adjusting the equalizer, set the bass, treble, balance and fader to “0”.
This unit is equipped with two parametric fil- ters. The first filter, “LOW EQ”, can be ad- justed from 32 to 500 Hz, the second, “HIGH EQ”, from 630 to 10 000 Hz. In this case, parametric means that one frequency can be increased or reduced for each of the two filters (+10 to -20 dB). The bandwidth/qual- ity of the two filters can also be adjusted.
This setting is described in the condensed instructions under 8 AUD.
Now listen to the MiniDisc with which you are familiar.
Evaluate your impression of the sound ac- cording to your taste.
/ · /

Selecting a quality factor for the bass or mid-range
repeatedly until “LO-Q- FAC” or “HI-Q-FAC” appear in the dis- play.
to save the selected equal- izer setting and return to the DPE main menu.
to save the selected factor and return to the DPE main menu.
This enables you to compare the sound with and without equalizer.
Selecting the preset sound setting
Selecting a preset influences the equalizer and sound settings of the unit. Each select- ed preset can be adjusted manually. When a different preset is selected, however, the factory default setting is restored. Your per- sonal sound settings for BASS, TREBLE, EQ and LD are stored in the “USER” preset mode.
repeatedly until “PRESET” appears on the display.

Begin adjustment with the mid-range/treble and complete it with the bass range.
Bass range 30 to 100 Hz
Bass response too weak
Avoid distortion. Raise the level cautiously if the loudspeaker diameter is too small.
Lower mid-range 100 to 400 Hz
Bass not clean Booming Unpleasant pressure on the ears
Reduce the lower mid-frequen- cies with Filter: “LOW EQ” Frequency: 125 to 400 Hz Level: Approx. -4 dB
The tonal response may be- come too thin and aggressive. Pay attention to the fundamen- tal tone range of the music.
Mid-range 400 to 4 000 Hz
Sound lacks depth, aggressive, no stereo effect
Reproduction must not be- come too faint. Tonal response too weak.
Treble 4 000 to 20 000 Hz
Response is dull Clarity lacking Instruments lack brilliance
Increase the treble range with Filter: “HIGH EQ” Frequency: Approx. 10 kHz Level: +2 to +4 dB
Avoid a sharp tonal response. Loud hissing impairs the quali- ty.
Frequency ranges · Tonal effect/problem · Measure

The car radio offers the facility to adjust cer- tain settings and functions to your require- ments and to store these changes with the aid of DSC (Direct Software Control). The default settings are selected at the fac- tory. An overview of the factory default settings is provided below for future reference.
ANGLE Adjust the display to your own viewing angle.
Activate/deactivate the dy- namic volume level display.
DIM DAY Select the display brightness for daylight (Stages 1-9).
SCROLL Appears only in MiniDisc mode. If the track name is to run continuously through the display, SCROLL ON must be selected.
DIM NIGHT Select the display brightness for darkness (Stages 1-9).
To alter a programming setting: • Press DSC. Select and adjust the functions described below by means of the rocker and the ENT key. The status of adjustment is shown on the display.
The brightness is switched over automatically by the headlights.
REG Appears only in radio mode. If you wish to receive re- gional programmes for your broadcast area, REG ON must be selected.
TA VOL Adjust the volume of traffic announcements and the warning signal from 0 - 66. Traffic announcements are played at this volume if the standard volume is lower. If the standard volume is greater than TA VOL, traffic announcements are played at the standard volume.
SHARX Automatic bandwidth switch- ing on the FM band. Where the station density is high, switch to SHARX ON with << >>: this largely elimi- nates interference from ad- jacent stations. ” SHARX ON” is the default setting.
Select function > Adjust/call up value
ON VOL Select the initial volume. Use << >> to select the de- sired initial volume. If “LAST VOL” is selected, the initial volume is the same as that last selected.
/

HICUT Interference-driven treble reduction. Treble frequen- cies are reduced only when interference is present. Can be selected from NO HICUT (OFF) to HICUT 3 (strongest treble reduction). Decide for yourself which setting is the most pleasant.
AMP DELAY Energization delay of exter-
12/24H MODE Select the time display (12 hour or 24 hour).
nal amplifiers. DLAY OFF signifies no energization de- lay. DLAY 1 to DLAY 4 sig- nify the energization delay in seconds.
CLK ON/OFF The time can be displayed
with the ignition on and the unit switched off. Select CLK ON in this case.
CDC NAME Displayed only in CD chang- er mode. You can use this function to assign any desired name to the CDs. (Refer to “Assign- ing names to CDs”.)
BEEP Confirmation signal for func- tions which require a key to be held down for approx. 1 second. The volume can be selected from 0 to 9 (0 = off).
Change the sensitivity of the seek run. ”SENS 1” indicates close re- ception, ”SENS 6” distant reception. Select “SENS 1” if you wish to receive strong stations in the near range; select “SENS 6” if you also wish to receive weaker, distant sta- tions.
CLOCKSET Manual adjustment of the
time. Use << >> to select hours/ minutes. The flashing range can be adjusted with
LED ON/OFF You can select between
LED ON and LED OFF. When LED ON is selected, the “ON” knob flashes to provide additional security when the unit is switched off and the KeyCard removed.
. Press ENT briefly to save after completing the setting. Refer also to “CLOCK time”.
STEREO/MONO
SCANTIME This setting defines the sampling time (5 - 30 sec- onds) for radio broadcasts and CD tracks.
Toggle << >>. The display indicates the se- lected state briefly. STEREO is selected auto- matically when the unit is switched on.
For activating/deactivating automatic hours correction. Refer also to “CLOCK time, hours correction”.
/

PTY LANG Select the language for pro- gramme type codes: Ger- man, English or French.
UPDATE In CD and CD changer mode, this function enables the names of CDs to be de- leted in order to create space for new CDs. (Refer to “Deleting CD names with DSC-UPDATE”.)
ANGLE 0 DIM DAY 9 DIM NIGHT 9 TA VOL 35 ON VOL LAST VOL PEAK ON/OFF ON SCROLL ON/OFF OFF REG ON/OFF OFF SHARX SHARX ON HICUT HICUT 2 FM/AM SENS SENS 6 STEREO/MONO STEREO AMP DELAY DLAY OFF CDC NAME - CLOCKSET 0:00 CLK AUTO / MAN CLK AUTO 12/24H MODE 24H MODE CLK ON/OFF CLK OFF BEEP 3 LED ON SCANTIME 10 sec. PTY LANG DEUTSCH AUX OFF LEARN KC - READ KC - UPDATE -
AUX ON/OFFThis menu item does not ap-
pear when a CD changer is connected. “OFF” is the de- fault factory setting. If an external unit is con- nected through AUX, “ON” must be selected.
End DSC programming/store settings: • Press DSC.
LEARN KC This function enables you to teach in a second KeyCard. Refer to the instructions un- der “KeyCard anti-theft pro- tection system” “Teaching in a second KeyCard”.
READ KC The data can be read out from a KeyCard. Unit data such as name, type number (76...) and seri- al number are displayed by the KeyCard supplied. Should you remove the Key- Card during the read proc- ess, “READ KC” appears in the display.

Glossary - Technical Terminology
AF – Alternative Frequency
EON – Enhanced Other Network
Output power: 4 x 25 watts sinusoidal to DIN 45 324 at 14.4 V 4 x 40 watts max. power
With RDS, this function ensures that the best frequency of the current programme which can be received is selected automatically.
With RDS, EON permits the exchange of transmitter information within a transmission chain. For example, a non-traffic programme sta- tion can be switched automatically to a traf- fic programme station for the duration of a traffic announcement. Following the an- nouncement, the original non-traffic an- nouncement station is selected again.
Power amplifier for increasing the output power.
Frequency bands: FM : 87.5 – 108 MHz MW : 531 – 1602 kHz LW : 153 – 279 kHz
AUD – Audio
Sound adjustment of basses and trebles, adjustment of the right/left (balance) and front rear (fader) volume ratios.
Sound control for adjustment of the frequen- cy response to the acoustic conditions and personal taste.
BND (Band)
FM sensitivity: 0.7 µV at 26 dB signal-to-noise ratio.
For selection of the frequency band and the memory level.
FM transmission range:
Press the key briefly to terminate or abort the adjustment process.
CL – Clear
Return to the previous menu item.
DSC – Direct Software Control
Blaupunkt’s anti-theft protection system. The unit can be operated only with the correct KeyCard.
Transmission range:
DSC can be used to adjust certain factory default settings according to the user’s per- sonal requirements.
Play CDs/CD tracks in random order.
Press briefly to accept/save the adjust- ments.
Switches audio off.

RPT (Repeat)
TPM – Track Program Memory
See also SCAN.
Repeat CD tracks. Tracks or CDs can be repeated in CD changer mode.
Stores and plays your favourite tracks in CD or changer mode.
For selection of a desired programme type in FM mode (e.g. sport, news). Refer also to RDS.
TS – Travelstore
Briefly plays the radio stations in your cur- rent reception range or the tracks on a CD in CD mode. Using Preset Scan you can scan the radio stations stored on the preset buttons.
Automatically stores the stations with the best reception on the station preset buttons. Very useful during long journeys.
RDS – Radio Data System
Service provided by the broadcast stations for improved listening convenience. For example, the station name is shown in place of the frequency.
Softkey (Software key)
Key with varying functions.
Further RDS functions include:
SRC - Source
AF – Alternative Frequency EON – Enhanced Other Network Radio Text REG – Regional Programme PTY – Programme Type TA – Traffic Announcement TP – Traffic Programme
Source switch between radio and CD chang- er.
TA - Traffic Announcement (priority for traf- fic information)
“TA” in the display indicates that the priority for traffic announcements has been switched on. See also RDS.
Assign priority to regional programmes. REG ON prevents the unit from switching automatically to a different regional pro- gramme of the same broadcasting station with better reception. Refer also to RDS.
TP - Traffic Program
“TP” in the display indicates that the radio is tuned into a station which broadcasts traffic information. See also RDS.
Preset Scan


Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.