EN
Gastroback logo
Official user manual

Gastroback 46006

16 pages·686 KB·Vacuum Packer·PDF·ENDEFRITNLJA
Gastroback 46006
Table of Contents 7 sections GASTROBACK · Instructions for use · Design vacuum cleaner Basic · IMPORTANT INDICATIONS FOR OPTIMAL FUNCTION · … ShowHide
Page 1 of the Gastroback 46006 user manual — GASTROBACK
Page 1 · click to enlarge
Page 1

GASTROBACK

Instructions for use

Design vacuum cleaner Basic

Instructions for use must be read before using them.

Article No 46006 Design Vacuum Basic

® · Model and accessory changes reserved!

Page 2 of the Gastroback 46006 user manual — IMPORTANT INDICATIONS FOR OPTIMAL FUNCTION
Page 2 · click to enlarge
Page 2

!

Please read all instructions and guidance provided with the device

delivered carefully and completely by before you

Please put the device into operation and observe all warnings,

which are listed in the user manual.

IMPORTANT INDICATIONS FOR OPTIMAL FUNCTION

  • For the welding of food use only special foil/foil bags provided for this purpose. Other bags melt due to the high temperature of the welding seal and would damage the welded seal by plastic residue.
  • Never touch the welding seal of the device when it is switched on. Risk of burning!
  • Note: For the best result, you should never fill the foil bag too full. Let's leave approx. 8 cm foil above the food free. Otherwise, no vacuum can be generated.
  • Make sure that the foil bag has no food particles, grease or liquids in the sealing area when you weld the foam bag; otherwise, it could affect the welding.
  • Freeze moist foods for a short time. During the vacuum process, no moisture can be sucked in and the foodstuffs are not pressed.
  • IMPORTANT: For proper function, make sure that the sealing ring is installed correctly.
  • IMPORTANT: The lid must latch correctly after insertion of the foil bag. You hear two clicks of sound when you snap in. Only then is the device ready for operation.
  • The apparatus is not suitable for continuous operation. Please wait for approx. 2 minutes after a vacuuming process before starting another operation.
  • IMPORTANT: The foil bags are not suitable for cooking or microwave. Be sure to take the foods out of the foil for warming up.
Page 3 of the Gastroback 46006 user manual — General precautionary measures
Page 3 · click to enlarge
Page 3

General precautionary measures

Read all instructions and notes about the device before Use carefully and completely through it, and preserve the Instructions are good. Use the Device and/or parts of it only in the manner specified therein for the purpose described (for intended use) and perform only work on the Equipment as described in these instructions. Unintentional use and especially misuse can lead to serious personal damage and property damage due to dangerous electrical voltage, hot surfaces and fire.

  • Check the device regularly for damage. Never use the equipment if it or parts thereof are damaged, have been subjected to excessive loads (e.g. fall, impact, overheating or moisture penetration) or no longer work as expected. Then immediately unplug the power plug from the socket and have the device checked in a specialist workshop.
  • Repair and maintenance of the equipment may only be carried out by authorised specialist workshops. Use only components, spare parts and accessories for the device that are intended and recommended by the manufacturer for this purpose to avoid scalding and exposure to overheating, fire or electricity.
  • Children and infirm persons must always be specially supervised when handling the device. Never leave the device unattended if it is accessible for young children. Make sure that young children can not tear the device down on the cable. The device is not suitable for use by children, physically or mentally impaired persons and those who have no experience unless they have received an introduction to the device from a person responsible for your safety. Children should be supervised to make sure they are not playing with the device. Always keep the device in a dry, clean and frost-free place where it is not accessible to young children.
  • Do not place heavy or hard objects on the device.
  • Place the device on a readily accessible, level, dry and sufficiently stable work surface. During operation, do not place valuable or sensitive objects on the weld seal to avoid damage from heat.
  • Never place the device on the edge or at the edge of the work surface. Provide enough space on the work surface for good air circulation: at least 20 cm on each side and 1 m above the device. Keep the work area clean and dry. Do not use the device in wet or damp areas.
  • Always let the device cool down first before you start another operation.
Page 4 of the Gastroback 46006 user manual — General precautionary measures
Page 4 · click to enlarge
Page 4
  • Always unplug the power plug first and clean the device before moving or putting it away for storage. Always lock the lid first so that the welding seal and sealing ring are protected during storage.

The weld seal of the design vacuum cleaner basic is heated electrically and must only be connected to a rubbed socket with the correct nominal values (230 V at 50 Hz; alternating current). The socket must be sufficiently secured for 110 watts (10 A or higher). In addition, the socket should be protected by a residual-current circuit breaker whose tripping current should not exceed 30 mA. In case of doubt, contact your electrician.

  • Do not connect the device via a multiple socket to avoid danger from fire and electricity.
  • Never leave the device unattended when the power plug is inserted. Unplug the power plug from the socket if you do not want to use the device, move the device or clean the device.
  • The use of extension cables is discouraged. If you still want to use an extension cable, then only use extension cables with a ground conductor, safety plug and safety coupling for a power of at least 110 Watt/10 A (wire cross section: 0.75 mm2 or more).
  • Always treat the cables carefully. Always unwind the cables used completely before you put the device into operation. Never put the device on a power cable. Do not let the cables hang down over the edge of the work surface. Keep power cords away from the heated appliance parts (welding seal). Never pull, tear or fold the cable, squeeze or knott. Keep the cables away from hot surfaces. Make sure that no one can step on the cable or stumble over it. Touch the housing of the plug when you unplug it.
  • Never dip or place appliances or cables in water or other liquids. Never pour liquids into the device or over the device, or cable. Never clean the appliance or parts of it in the dishwasher.
  • The apparatus is not suitable for continuous operation. Please wait for approx. 2 minutes after a vacuuming process before starting another operation. By overheating (even under strong environmental influences) (e.g. B. 35 degrees or overvoltage +10 percent may cause the automatic thermal protection system of the device to switch on. In this case, let the device cool for a few minutes until it is ready to operate again.
Page 5 of the Gastroback 46006 user manual — General precautionary measures
Page 5 · click to enlarge
Page 5

Hot surfaces - risk of combustion

The design vacuum cleaner Basic is used for the welding of food and the weld seal becomes very hot during operation.

  • The welding seal is electrically heated. The heating system begins to work automatically once the vacuuming process is complete. Never place foreign bodies (paper, textiles or plastic) on the heating surface of the welding seal to avoid damage to the device and fire risk!

Even after the sealing process, the welding seal is still very hot for some time. Allow the device to cool down briefly before you start another process.

Never during operation or shortly after use, contact the welding seal with any body parts or heat-sensitive objects.

  • Special care is required if you want to clean the device. Always unplug the power plug first and wait until the weld seal has cooled to room temperature before cleaning the device.
  • Never place the device or parts of it in or on furnaces, or near strong sources of heat (example: heating systems, burners). Keep power cords away from the heated appliance parts (welding seal). Never put the device on a power cord!
  • Never operate the device in the vicinity of combustible, highly flammable materials (example: alcohol, spirit, gasoline). Place never heated alcoholic beverages (example: mulled wine, grog) or hot food containing alcohol next to the device. Due to the heat, alcohol evaporates very quickly and forms an ignitable mixture which can lead to deflagration due to contact with ignition sources (example: candles, burning cigarettes, heating rods in the device) and cause serious damage to persons and property.
Page 6 of the Gastroback 46006 user manual — Get to know the design vacuum cleaner basic
Page 6 · click to enlarge
Page 6

Get to know the design vacuum cleaner basic

Closure opening for the cover

Seal Only button = sealing only = start signal lamp lights red = device works out signal lamp = seal mode ended

Cancel process Press key = Vacuum = Start signal lamp lights up red

Seal Only button lights up additionally = vacuum process ended

Seal Only and Vacuum Seal = both signal lamps off = sealing process ended

Show 7 more labels / short text on this page
Rubber seal · Weld seal · Cover · Sealing rings · Operating menu · (on both sides) · Connection for vacuum hose adapter
Page 7 of the Gastroback 46006 user manual — B
Page 7 · click to enlarge
Page 7

Make the device operational

1. Unpack the device carefully, place it on a suitable dry work surface (see: General safety instructions). Make sure you have enough space in front of the device so that you can put the foil bag before the device when vacuuming.
2. Make sure the sealing ring (in the lower part of the device) is inserted correctly. The sealing ring must lie correctly in the guide channel and not project beyond the edge of the guide groove.
3. Plug the power plug into a suitable wall outlet for 230 V, 50 Hz, AC (see: Precautions when handling electricity). The device is operational.

A

1. After you have made the device ready for use (see: Make it operational), press the shutter openings on both outsides of the device and open the lid (see Fig.). A. Make sure the weld seal is clean and that there are no foreign bodies on the heating surface.
2. Take the roll with the slide and cut a corresponding (not too short) piece of slide from the reel. IMPORTANT: Make sure that after filling the foil bag you have at least 8 cm of film above the pouch fill height to seal. You need this 8 cm film length for vacuuming.

B

3. Place one of the open ends of the foil over the weld seal. For sealing the film bag bottom, it is sufficient if the film extends over the welding seal (FIG. B. The film need not extend over the sealing ring into the vacuum chamber, since no vacuum has to be produced for sealing of the sheet bag bottom.
4. Close the lid and press the cover on the marked places (Fig. 1). C) firmly downwards until the lid is locked in with two clicks and

sealing the film bag

Page 8 of the Gastroback 46006 user manual — F
Page 8 · click to enlarge
Page 8

is tightly closed. Make sure that the lid is securely closed and latched. Only then is the device ready for operation.

D

5. Press the Seal Only button (Fig. 1). D. The device starts to work. The signal lamp of the Seal Only button lights up red. The device operates in sealing mode and the bag bottom is welded. When the sealing process is completed, the lamp goes out.

E

6. Now open the device by pressing the shutter openings on both outsides of the device (Fig. 1). E) and remove the foil bag.
7. Check if the weld is uniform. The weld is then secure and tight if it is smooth, and no patterns of the uneven side of the foil bag can be seen at the seam.
8. After you have sealed the bag floor and made sure that the weld is secure and tight, you can fill the bag with food.

F

9. Place the open side of the foil bag over the weld seal. For sealing the film bag, the film must reach into the vacuum chamber via the welding seal and the lower edge of the gasket ring (FIG. F. If the film bag does not reach into the vacuum chamber, no vacuum can be produced. Make sure that the

Vacuum in the foil bag

Page 9 of the Gastroback 46006 user manual — H
Page 9 · click to enlarge
Page 9

The foil bag does not extend over the pin in the center of the vacuum chamber. This is necessary for generating the vacuum and must not be blocked.

G

10. Close the lid and press the cover on the marked places (Fig. 1). G) firmly downwards until the lid is locked and tightly closed with two clicks. Make sure that the lid is securely closed and latched. Only then is the device ready for operation.

H

11. Press the Vacuum Seal button (Fig. 1). H. The device starts to work. The signal lamp of the Vacuum Seal button lights up red. The air is sucked out of the foil bag and a vacuum arises. Once the vacuuming process is complete, the signal lamp of the Seal Only button additionally lights up. The device operates in the sealing mode of the film bag is welded. When the sealing process is completed, both signal lamps are extinguished.
12. Now open the device by pressing the shutter openings on both outsides of the device (Fig. 1). I) and remove the foil bag.
13. Check if the weld is uniform. The weld is then secure and tight if it is smooth, and no patterns of the uneven side of the foil bag can be seen at the seam. NOTE: The device is not suitable for continuous operation. Please wait for approx. 2 minutes after a vacuuming process before starting another operation.
14. Unplug the power plug from the socket as soon as you stop using the device for a long time. NOTE: If the device fails to create a vacuum, it will automatically shut down after 30 seconds. In this case, check whether the foil bag has a hole or if the foam bag is inserted correctly.
Page 10 of the Gastroback 46006 user manual — D
Page 10 · click to enlarge
Page 10
1. After you have made the device ready for use (see: Make it operational), press the shutter openings on both outsides of the device and open the lid (see Fig.). A.

A

2. Take the supplied vacuum hose adapter and connect the tube (with its narrower end) to the pin in the middle of the vacuum chamber (Fig. 1). B. The hose must be firmly seated and not slip.

B

3. Fill the container with food.
4. Place the vacuum bell of the Vacuum Hose Adapter over the black rubber seal on the lid of the container. Press the vacuum bell slightly on the cover so that it closes off airtight with the cover (FIG. 1). C.
5. Now press the Vacuum Seal button (Fig. 1). D. The device starts to work. The signal lamp of the Vacuum Seal button lights up red. The air is sucked out of the container and a vacuum arises. When the vacuuming process is completed, the signal lamp goes out. The food is now vacuum packed in the container.

D

If you want to take the food out of the container, you need to easily pull the black rubber seal on the lid of the tank aside. The pressure produced during vacuuming is thus left out of the container. You can hear air entering the container and now open it.

Vacuum in the container

Page 11 of the Gastroback 46006 user manual — Get to know the design vacuum cleaner basic
Page 11 · click to enlarge
Page 11

Turn off the device and unplug from the socket.

Slightly moisten a cloth or sponge with warm dishwasher solution and use it to clean the heating surface of the weld seal (if necessary). Make sure that no water runs into the device.

If necessary, you can remove the gasket in the lower part of the device for cleaning. Carefully remove the gasket by pulling the gas seal upwards.

During vacuuming, up to 90% of the oxygen is removed from the foil bag or filtered. The container is sucked and everything closed airtight. Oxygen, light and temperatures above 0 degrees cause food to spoil quickly.

  • The vacuum prevents oxidation of the food and deprives bacteria or mold from developing.
  • The food is protected from odors and retains its full taste.
  • No odors can form in the refrigerator.
  • The nutrients and minerals are preserved.
  • The foods remain fresh up to 5 times longer.
  • Frozen goods are protected from freeze burning and retain their natural colour.

Cleaning · Advantages of Vacuuming

Page 12 of the Gastroback 46006 user manual — Get to know the design vacuum cleaner basic
Page 12 · click to enlarge
Page 12
  • Food must be cooled in the refrigerator before vacuuming to create an optimal vacuum.
  • Foods with a high moisture content should be frozen briefly in the freezer before vacuuming. During vacuuming, no moisture can be attracted and the food is not pressed.
  • IMPORTANT: The foil bags are not suitable for heating the vacuum-packed food in them in a microwave or hot water bath.
  • NOTE: Before you vacuum pack fresh fish, be sure to remove the offal.
  • Do not overfill the foil bags or vacuum containers. In this case, difficulties can occur in the production of the vacuum.
  • Make sure that the opening of the foil bag is dry, lies flat and no food residues are in the sealing area. Otherwise, the foil bag cannot be properly sealed.
  • Carefully wipe excess air out of the foil bag before you start vacuuming to optimize the vacuuming process and not overload the device.
  • They can be used e.g. B. Matches, first aid bags and clothing Vacuuming around these objects from moisture content e.g. B. When camping, protect or vacuum silver jewelry and thus protect it from tarnishing.
  • Do not vacuum sharp, hard objects such as B. bones or molluscs. The sharp edges can tear the film bag during vacuuming and thus prevent a vacuum.
  • To create ice batteries for your refrigerator or as an ice pack for injury, fill a 2/3 foil bag with water and seal the foil pouch.

Food Normal storage Vacuum packed

fresh raw meat 3 days 9 days cooked meat 5 days 15 days fresh fish 2 days 5 days fruits and vegetables 5 days 14-21 days

Durability table

Page 13 of the Gastroback 46006 user manual — Get to know the design vacuum cleaner basic
Page 13 · click to enlarge
Page 13

Food Normal storage Vacuum packed

Sausage/ham 7 days 20 days Soup 2 days 10 days Cream pastries 2 days 8 days Bread 2 days Eight days Rice / Pasta / Coffee / Tea 180 days 365 days

* Storage in the refrigerator at 3-5 degrees

Food Storage Normally packaged Vacuum packed

fresh berries refrigerator 1-2 days 10 days hard open cheese refractory 3-4 months 6-8 months coffee beans refraction cabinet 2 weeks 2 years ground coffee cupboard 2 years 5 years biscuits (packed) cabinette 2 months 6 months 6 month fish freezer compartment 2 months mottled meat (beef) freezer space compartment 6-9 months poultry chicken freezer 12 months 3 year cowl freezer 2-3 months nuts freezer 2 months noodles (uncooked) cup board 2 years rice (unboiled) closet 6 months 2 years sugar cup Board 2 years 4 years fresh vegetable freezer 10 months 3 years

WARNING: Turn off the device, always unplug first, let it cool down enough and clean before putting it away for storage. Always keep the device in a clean, dry and frost-free place where it is protected against excessive stress (falling, bumps, blows) and inaccessible to young children. Do not place heavy objects on the device. Clean the device after the instructions in section cleaning. Make sure that no foreign bodies are on the heating surface of the weld seal. Close the lid and keep the device on a flat, solid and stable base.

The equipment must be disposed of in accordance with local regulations for the disposal of e-waste. If necessary, check with your local waste disposal company.

Durability table · Storage · Disposal instructions

Page 14 of the Gastroback 46006 user manual — Get to know the design vacuum cleaner basic
Page 14 · click to enlarge
Page 14

Help with troubleshooting

Possible problem The Simple Solution to the Problem

The device is not working when it is switched on

  • Check whether the device is connected to the mains correctly and if the power plug works. To test the socket, connect another device.
  • Check if power plugs and power cords are in order. If they are damaged, contact an authorized customer service office.
  • The device automatically switches off when overheated. Allow the device to cool for 15 minutes and try again.

The device does not seal the foil bag bottom

  • Check whether the foil bag is correctly placed (see: sealing of the foam bag) and if the film on the sealing surface is dry and flat.

The device does not vacuum properly and there is too much oxygen left in the foil bag

  • Check whether: - the foil bag is correctly placed (see vacuuming in the foam bag) and if the end of the folio bag extends into the vacuum chamber, but not over the pin in the middle of the vacuum room. - the sealing ring is inserted correctly - contaminants are present on the welding seal or gaskets - food particles in the film bag lie above the welded seal - the film pouch has a hole - This can be checked by taking the weldable bag and keeping it under water. With light pressure on the bag, air would escape and small bubbles of air would rise. In this case, re-weld the bag or fill the food into a new foiled bag.

The device does not seal the foil bags correctly

  • Check whether: - the foil bag is correctly placed (see vacuuming in the foam bag) and if the end of the folio bag extends into the vacuum chamber, but not over the pin in the middle of the vacuum room. contaminants are present on the welding seal or sealing ring - food particles in the film bag lie above the welded seal
  • If the weld seal becomes too hot, the foil bag melts - open the device and leave the unit some

Cool for minutes.

  • In the event of overheating, the device shall be switched off automatically. Allow the device to cool for 15 minutes and then try again.
Page 15 of the Gastroback 46006 user manual — Get to know the design vacuum cleaner basic
Page 15 · click to enlarge
Page 15

Help with troubleshooting

Possible problem The Simple Solution to the Problem

No vacuum is created in the container

  • Check whether: - the vacuum hose adapter is correctly connected to the device (see: Vacuuming in container) - the lid of the container is closed off airtight with the cover - the cover of the tank is properly sealed - the black rubber gasket on the tank cover is correctly fastened in the opening of the cover – the black elastic seal is brittle or has holes - the suction tube adaptor and both connection points of the hose have no defects or are broken off - the tank does not overcrowd - leave at least 3 cm free space underneath the edge of the deck!

The foil bag loses its vacuum after sealing

  • Folding, crumbs, grease or moisture in the weld seam can cause leakage. Open the bag, clean the inner side of the foil bag on the weld and seal it again.
  • Some foods (such as e.g. B. Fresh fruits and vegetables can ferment or release natural gases.
  • Lack of refrigeration or changing temperatures can cause food to spoil.
  • Check the bag for damage in which you hold the bag under water. With light pressure on the bag, air would escape and small bubbles of air would rise. In this case, re-weld the bag or fill the food into a new foiled bag.

The container loses the vacuum

  • Check whether: - the rubber seal is brittle or has holes - the seal fits correctly on the container lid edge,

dirty or damaged

We guarantee for all Gastroback electrical appliances that they are defect-free at the time of purchase. Proof of manufacturing or material defects will be replaced or corrected free of charge, excluding further claims and within two years after the date of purchase. A warranty claim of the buyer does not exist if the damage to the device can be attributed to improper treatment, overload or installation errors.

Technical interventions by third parties without our written consent will lead to the immediate expiry of the warranty claim. The buyer must present the original proof of purchase in order to assert the claim and, if warranted, bears the costs and risk of transport.

Guarantees/guarantees

Page 16 of the Gastroback 46006 user manual — GASTROBACK GMBH
Page 16 · click to enlarge
Page 16

GASTROBACK GMBH

Business Route 20 • D-21279 Hollenstedt/Germany

http://www.gastroback.de • Email: [email protected]

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Gastroback 46006

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Gastroback 46006

Be the first to ask — other owners or our team will answer.

Original document

Gastroback 46006 manual PDF

16 pages·686 KB·Vacuum Packer·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…