EN
Beper logo
Official user manual

Beper BC001

44 pages·2 MB·Coffee Machine·PDF·ENNLJA
Beper BC001
Page 1 of the Beper BC001 user manual
Page 1 · click to enlarge
Page 1

GENERAL SAFETY ADVICE READ THE OPERATING INSTRUCTIONS CAREFULLY BEFORE FIRST USE OF THE APPLIANCE. Read the following instructions carefully, since they give you useful safety information about installation, use and maintenance and help you avoid mishaps and possible accidents. Remove the packing and make sure that the appliance is intact, with special attention to the supply cable. The elements of the packing (plastic bags, polystyrene, etc) do not have to be accessible to the children, in order to preserve them from danger sources. It is recommended not to throw these packing material in the dome stic waste, but to deliver them to the appropriate station of collection or destruction refusals, asking eventually information to the manager of the Sanitation Department of your own municipality. Before connecting the appliance make sure that the mains voltage corresponds to the data specified on the label. If the plug does not suit the socket, let it be replaced with another suitable plug by qualified personnel only, which shall also ensure that the section of the socket cables is suitable for your appliance power absorption. Never pull the supply cord to unplug the appliance. Make sure that the supply cord never comes into contact with hot or cutting surfaces Do not use this appliance if the supply cord is damaged. In case of damage, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. Only connect this appliance on alternating current Generally, the use adaptors multiple plugs and/or extensions is not recommended; should they be necessary, please use only simple or multiple adaptors and extensions in compliance with the safety rules in force, making sure that the capacity absorption limit marked on the simple adaptors and the extensions and the maximum power limit marked on the multiple adaptor are not exceeded. This appliance is to be destined to its special purpose only. Any other use is to be considered as improper and thus dangerous. The manufacturer cannot be responsible for any damages deriving from improper, wrong or incautious use. To avoid any heating risk, it is recommended to unroll completely the supply cord and to unplug the appliance, when not used.

Page 2 of the Beper BC001 user manual
Page 2 · click to enlarge
Page 2

Before cleaning, always unplug the appliance. To protect against electric shock, do not immerse cord, plug or any parts of the appliance into water or other fluids. Do not hold the appliance with wet hands or feet. Do not hold the appliance with naked feet. Do not expose the appliance to atmospheric agents such as rain, wind, snow, hail. Do not use the appliance near explosives, highly flammable mate rials, gases, burning flames, heaters. DO NOT ALLOW CHILDREN, DISABLED PEOPLE OR EVERY PEOPLE WITHOUT EXPERIENCE OR TECH NICAL ABILITY TO USE THE APPLIANCE IF THEY ARE NOT PROPERLY WATCHED OVER. CLOSE SU PERVISION IS NECESSARY WHEN ANY APPLIANCE USED BY OR NEAR CHILDREN. MAKE SURE THAT CHILDREN DO NOT PLAY WITH THIS APPLIANCE. IF YOU DECIDE NOT TO USE THE APPLIANCE ANY LONGER, MAKE IT UNSERVICEABLE BY SIMPLY CUTTING THE SUPPLY CABLE AFTER DISCONNEC TING THE PLUG FROM THE SOCKET. ALSO MAKE ANY DANGEROUS PARTS UNSERVICE ABLE, ESPECIALLY FOR CHILDREN WHO COULD PLAY WITH THE APPLIANCE.

Page 3 of the Beper BC001 user manual
Page 3 · click to enlarge
Page 3
Beper BC001 diagram (page 3)
Fig. 1

COMPONENTS 1. Water tank cover 2. Water tank handle 3. Water tank 4. Power indicator 5. Ready indicator 6. Knob 7. Steam wand 8. Froth device 9. ON/OFF switch 10. Coffee spoon 11. Drip tray 12. Drip plate 13. Funnel handle 14. Steel mesh 15. Steam button

Before the first use To ensure the first cup of coffee tastes excellent, you should rinse the coffee maker with warm water as follows: 1. Pour water into water tank, the water level should not exceed the “MAX” mark in the tank. Then replace the water tank cover. Note: the appliance is supplied with a detachable tank for easy cleaning, you can fill the tank with water firstly, and then put the tank into the appliance. 2. Set steel mesh into metal funnel (no coffee in steel mesh). make sure the tube on the funnel ali gns with groove in the appliance, then insert the funnel into the appliance as indicating of “INSERT” mark, and you can fix them into coffee maker firmly through turn it anticlockwise until it is fully locked. 3. Place an espresso cup (yourself cup) on removable drip plate. Make sure the knob is on the po sition which is the“ ”position. Note: the appliance is not equipped with jug, please use yourself jug or coffee cup. 4. Connect to power source, press the ON/OFF switch. The power indicator (red) will be illuminated. 5. Turn the knob to the “ ” position, the pump will pump water, when there is water flowing out and close the pump by turning knob again to the “ ” position, make sure the steam button is on the higher position which is the “ ” position and waiting for a moment, the appliance begins to be pre-heated until the ready indicator (blue) is illuminated, it shows the pre-heating is finish. Turn the knob to the “ ” position again, and water will flow out. 6. After about one minute, turn the knob to the “ ” position to stop brewing, you can pour the water in each container out then clean them thoroughly, now you can start brewing.

Pre-heating To make a cup of good hot Espresso coffee, we recommend you preheating the appliance before making coffee, including the funnel, filter and cup, so that the coffee flavour can not be influenced by the cold parts. 1. Remove the detachable tank and open the tank cover to fill it with desired water, the water level should not exceed the “MAX” mark in the tank. Then place the tank into the appliance properly.

Page 4 of the Beper BC001 user manual
Page 4 · click to enlarge
Page 4

2. Set steel mesh into metal funnel, make sure the tube on the funnel aligns with groove in the appliance, then insert the funnel into the appliance as indicating of “INSERT” mark, and you can fix them into coffee maker firmly through turn it anticlockwise until it is fully locked. 3. Place an espresso cup (yourself cup) on removable drip plate. 4. Then connecting the appliance to power supply source. Make sure the knob is on the “ ” posi tion. 5. Press the ON/OFF switch, the power indicator (red) will be illuminated, make sure the steam but ton is on the higher position which is the “ ” position. Turn the knob to the “ ” position, when there is water flowing out, close the pump immediately by turning knob again to the “ ” position. The purpose of the step is that pump the water of the tank into the housing. 6. When the ready indicator (blue) is illuminated, you should turn the knob to the “ ” position again, there will be hot water flowing out. When the ready indicator (blue) is extinguished, close the pump by turning knob again to the “ ” position. The pre-heating is finished.

Make espresso coffee 1. Remove the funnel by turning it in clockwise, .Add ground coffee to steel mesh with coffee spoon, a spoon ground coffee power can make about a cup of top-grade coffee, then press the ground coffee powder tightly with the coffee spoon. 2. Set steel mesh into metal funnel, make sure the tube on the funnel aligns with groove in the ap pliance, then insert the funnel into the appliance as indicating of “INSERT” mark, and you can fix them into coffee maker firmly through turning it anticlockwise until it is at the “LOCK” position . 3. Pour out the hot water in the cup. Then place the hot cup (yourself cup) on drip plate. 4. At the time, the ready indicator (blue) is illuminated, once the blue lamp is illuminated, you should turn the knob to the “ ” position, waiting for a moment, there will be coffee flowing out. Note: During continuous operations, the ready indicator is likely to extinguish due to the inadequate temperature of the water in the boiler, but it does not mean the unit will stop operating, you may continue to make coffee regardless of it. 5.You should turn the knob to the “ ” position manually when desired coffee is obtained or the colour of coffee changes weak obviously,your coffee is ready now. WARNING: Do not leave the coffee maker unattended during making the coffee, as you need ope rate manually sometimes! 6. After finishing making the coffee, you can take the metal funnel out through turn clockwise, then pour the coffee residue out with the steel mesh pressed by press bar. 7. Press the power switch to cut off the power source. 8. Let them cool down completely, then rinse under running water.

Frothing milk / make cappuccino You get a cup of cappuccino when you toping up a cup of espresso with frothing milk. Method: 1- Prepare espresso first with container big enough according to the part “MAKE ESPRESSO COF FEE”, make sure that the knob is at the “ ” position. 2- Press down the steam button to the lower position which is the “ ” position, waiting for until the ready indicator (yellow) is illuminated. Note: During continuous operations, the ready indicator is likely to extinguish due to the inadequate temperature of the water in the boiler, but it does not mean the unit will stop operating, you may continue to make cappuccino regardless of it.

Page 5 of the Beper BC001 user manual
Page 5 · click to enlarge
Page 5

3 - Fill a jug with about 150 grams of milk for each cappuccino to be prepared, you are recommen ded to use whole milk at refrigerator temperature (not hot!). Note: In choosing the size of jug, it is recommend the diameter is not less than 70±5mm, and bear in mind that the milk increases in volume by 2 times, make sure the height of jug is enough. 4 - Insert the steam wand(with the frothing device) into the milk about two centimetre, then turn the knob to the “ ” position , steam will come out from the steam wand. Froth milk in the way moving vessel round from up to down. 5. When the required purpose is reached, you can turn the knob to the “ ” position. Note: Clean steam outlet with wet sponge immediately after steam stops generating, but care not to hurt! 6. Pour the frothed milk into the espresso prepared, now the cappuccino is ready. Sweeten to taste and if desired, sprinkle the froth with a little cocoa powder. 7. Press the power switch to cut off the power source.

Producing steam to heat liquids The steam wand (without the frothing device) can be used to make hot beverages like drinking chocolate, and water. Method: 1. Remove the detachable tank and fill it with desired water, the water level should not exceed the “MAX” mark in the tank. Then place the tank into the appliance properly. 2. Then connecting the appliance to power supply source. 3. Press the ON/OFF switch, the power indicator (red) is illuminated. 4.Turn the knob to the “ ” position, make sure the steam button is on the higher position which is the“ ”position, the pump will pump water, when there is water flowing out, close the pump imme diately, pressing down the steam button to the lower position which is the “ ” position and waiting for a moment, the appliance begins to be heated until the yellow lamp is illuminated, it shows the heating is finish. 5. Remove the frothing device from the steam wand. 6. Dip the steam wand into the liquid to be heated. Turn the knob to the “ ” position. 7. When the required temperature is reached, you can turn the knob to the“ ” position. 8. Press the power switch to cut off the power source.

Automatically power-off function 1. After pressing power switch, if there is no any operation within 25 minutes, the unit will power off automatically. 2. After pressing power switch, if there is no any operation after pump worked for 3 minutes during brewing coffee, the unit will power off automatically.

Page 6 of the Beper BC001 user manual
Page 6 · click to enlarge
Page 6

Clean and maintenance 1 - Cut off power source and let the coffee maker cool down completely before cleaning. 2 - Clean housing of coffee maker with moisture-proof sponge often and clean water tank, drip tray and removable shelf regularly then dry them. Note: Do not clean with alcohol or solvent cleanser. Never immerse the housing in water for clea ning. 3 - Detach the metal funnel through turn it clockwise, get rid of coffee residue inside, then you can clean it with cleanser, but at last you must rinse with clear water. 4 - Clean all the attachments in the water and dry thoroughly.

Claning material deposit 1. To make sure your coffee maker operating efficiently, internal piping is cleanly and the peak flavor of coffee, you should clean away the mineral deposits left every 2-3 months. 2. Fill the tank with water and descaler to the MAX level ( the scale of water and descaler is 4:1, the detail refers to the instruction of descaler. Please use “household descaler”, you can use the citric acid (obtainable from chemist’s or drug stores) instead of the descaler (the one hundred parts of water and three parts of citric acid). 3. According to the program of pre-heating, put the metal funnel (no coffee powder in it) and carafe (jug) in place. Brewing water per “ PRE-HEATING”. 4. Press the ON/OFF switch, the power indicator (red) will be illuminated, you should turn the knob to the position, make sure the steam button is on the higher position which is the “ ” position, when there is water flowing out and close the pump by turning the knob to the“ ” position, and waiting for a moment, the coffee maker begins to be heated. 5. When the ready indicator (blue) is illuminated, it shows the heating is finish. Turning the knob to the“ ” position and make make two cups coffee (about 2Oz). Then close the pump and wait for 5s. 6. Press down the steam button to the lower position which is the “ ” position, waiting for until the yellow indicator is illuminated. Make steam for 2 minutes, then turn the knob to the“ ”position to stop making steam. Press the power switch to stop the unit immediately, make the descalers deposit in the unit at least 15 minutes. 7. Restart the unit and repeat the steps of 4-6 at least 3 times. 8. Then pressing and release the steam button to the higher position which is the “ ”position, when the blue lamp is illuminated, Turning the knob to the“ ” position to brew until no descaler is left. 9. Then brewing coffee (no coffee powder) with tap water in the MAX level, repeat the steps of 4-6 for 3 times (it is not necessary to wait for 15 minutes in step of 6), then brewing until no water is left in the tank. 10. Repeat the step of 9 at least 3 times to make sure the piping is cleanly.

Page 7 of the Beper BC001 user manual
Page 7 · click to enlarge
Page 7
Technical Data Power960-1140W Power supply: 220-240V~50Hz

For any improvement reasons, Beper reserves the right to modify or improve the product without any notice.

The European directive 2011/65/EU on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimize the recovery and recycling of the materials they contain, and reduce the impact on human health and the environment. The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the appliance, it must be separa tely collected.

Page 8 of the Beper BC001 user manual
Page 8 · click to enlarge
Page 8

GUARANTEE CERTIFICATE This appliance has been checked in the factory. From the date of original purchase a 24 month guarantee applies to material and production defects. The purchase receipt and the guarantee cer tificate must be submitted together in case of claim to guarantee.

The guarantee is valid only with a guaranty certificate and proof of purchase (fiscal receipt) indicating the date of purchase and the model of the appliance

For any technical assistance, please contact directly the seller or our head office in order to preserve the appliance’s efficiency and NOT TO void the guarantee. Any intervention on this appliance by non-authorized persons will automatically void the guarantee.

GUARANTEE CONDITIONS If the appliance shows defects as a result of faulty material and/or production during the period of guarantee, we guarantee repair free of charge on condition that:

- The appliance has been used properly and for the purpose for which it has been intended. - The appliance has not been tampered with, otherwise it is not maintainable. - The purchase receipt shall be presented. - The appliance showing a fair wear and tear shall not be covered by this guarantee.

Therefore, any part that could be accidentally broken or having visible signs of use in consumable products (such as lamps, batteries, heating elements…) the aesthetic parts are excluded from the guarantee, and any defect whatsoever resulting from non-respect of the rules for use, negligence in usage and/or maintenance of the appliance, carelessness, wrong or improper installation, damage during transport and any other damage not attributable the supplier.

For every defect that could not be repaired within the guarantee period, the appliance will be repla ced free of charge.

In any case, if the part to be replaced for defect, breakage or malfunction is an accessory and/or a detachable part of the product, Beper reserves the right to replace only the very part in question and not the entire product

TECHNICAL ASSISTANCE Even after the guarantee period we will always pay attention to repairs for defected appliances. For technical assistance and/or repairs after the guarantee period you can directly contact the below address:

CONTACT YOUR DISTRIBUTOR IN YOUR COUNTRY OR ATER SALES DEPARTMENT BEPER. E-MAIL assistenza@beper.com WHICH WILL FORWARD YOUR ENQUIRIES TO YOUR DISTRI BUTOR.

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Beper BC001

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Beper BC001

Be the first to ask — other owners or our team will answer.

Original document

Beper BC001 manual PDF

44 pages·2 MB·Coffee Machine·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…