Instruction/ maintenance manual of the product 73G8 Bissell
Go to page of 16
USER’S GUIDE 3574/73G8/3576/20Q9 SERIES Safety Instructions 3 Product View 4 Assembly Instructions 5-6 Operation / Special T ools 6-8 Maintenance 8-12 T roubleshooting 12-13 Warranty 16 Replacement Parts 14 Consumer Ser vices 15 CleanView ® II BAGLESS DJ68-00280A REV(0.
2 Thanks For Buying A BISSELL CleanV iew ® II We’ re glad you purc hased a BISSELL CleanView II Vacuum. Ever ything we know about floor care went into the design and construction of this complete, high-tech home vacuuming system. Y our BISSELL CleanView II is well made , and we back it with a limited comprehensive one-year warr anty .
3 IMPOR T ANT SAFETY INSTR UCTIONS When using an electrical appliance, basic precautions should be obser ved, including the following: READ ALL INST R U CTIONS BEFORE USING Y OUR UPRIGHT V ACUUM. Always connect to a polarized outlet (left slot is wider than right).
4 C AUTION: Do not plu g in you r va cu um cleaner until you are familiar with all instructions a nd operating procedures. Power Switch Carrying Handle Crevice T ool Post-Motor Filter Quick Reach ® H.
5 How T o Put It T ogether Select Models Only Th e o nl y t ool yo u’ ll ne ed to a ss em bl e yo ur va cu um cleaner is a screwdriver . Locate the vacuum Handle and remove the screw packet ta ped to the base of the Handle. Stand the vacuum upright and slide the base of the Handle firmly into the grooves at the top of the vacuum bod y .
Press the Handle Release Pedal with your foot to place your vacuum in one of three cleaning positions. Upright- For stora ge and above floor c leaning with tools. Normal Cleaning- Press Handle Release Pedal once. Use for most household floor cleaning tasks.
Y our BISSELL CleanView II is not only a pow - erful carpet and rug vacuum c leaner , it’ s also a versatile above floor vacuum cleaner when you select one of the special tools. Raise Handle to Upright Position. Grasp the Quick Reach Handle and lift Hose Wand to separate from suction intake opening.
T o maintain maximum cleaning performance, the following maintenance steps must be performed: Empty the Dirt Container when the dirt reaches the “Full” line on the side. Check the Inner and Outer Circular Filters and the Pre-Motor Filter at least once a month and c lean or replace as needed.
Separate the Outer foam and Inner pleated Circular Filters. Wash each individually by hand in warm water . Mild detergent may be used if desired. Rinse well, then air dry thoroughly before putting them back together and replacing in Filter Cup. The Filter Cup may be washed in warm wa ter with a mild detergent.
For standard models , remove the four screws as shown with a Phillips Head Screwdriver . Lift the Brush Cover off. For wide cleaning path models , Lift tab 1 and release the three la tches in order 2-4 as marked. Lift the Brush Cover off. Grasp Rota ting Floor Brush at both ends and lift.
Determine the light bulb type of your vacuum: Standard Bulb (#203-1297) – approximately 1” long, flat end Large Bulb (#203-1007) – approximately 2” long, round end Standard Bulb – remove the bulb from the socket by grasping bulb and pulling straight out.
12 T roubleshooting V acuum cleaner won’t run P ossible Causes Remedies Power cord not plugged in Check electrical plug Blown fuse/tripped breaker Check/Replace fuse or reset breaker V acuum cleaner.
V acuum cleaner won’t pick up dirt continued P ossible Causes Remedies Dirt Container not installed properly Position correctly and lock in place Filters are dirty Check and clean Inner and Outer Ci.
14 Replacement P arts – BISSELL Cleanview II Series 1 2/3 4 7 5 6 8/9 10 11 12 14 15 16 17 13 7 Y ou may purchase replacement parts from your retailer , by calling BISSELL Consumer Ser vices or by visiting our website.
BISSELL Consumer Ser vices For information about repairs or replacement parts, or questions about your warranty , call: BISSELL Consumer Ser vices 1-800-237-7691 Monday - Frida y 8 a.m. — 10 p.m. ET Saturday 9 a.m. — 8 p.m. ET Or write: BISSELL Homecare Inc .
Warranty 16 This warranty gives you specific legal rights, and you may also have other rights which may var y from state to state. If you need additional instruction regarding this warranty or have questions regarding what it may cover , please contact BISSELL Consumer Services by E-mail, telephone, or regular mail as described below.
An important point after buying a device Bissell 73G8 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bissell 73G8 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bissell 73G8 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bissell 73G8 you will learn all the available features of the product, as well as information on its operation. The information that you get Bissell 73G8 will certainly help you make a decision on the purchase.
If you already are a holder of Bissell 73G8, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bissell 73G8.
However, one of the most important roles played by the user manual is to help in solving problems with Bissell 73G8. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bissell 73G8 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
