Instruction/ maintenance manual of the product 30C7 Bissell
Go to page of 20
Earn BISSELL Rewards! R egister your product today! See details on back page 2 Thank Y ou USER'S GUIDE 30C7 SERIES Safe ty Instr uctions Product Vie w Assembly Operations Maintenance and Car e T .
www.bissell.com 800.237.7691 T hanks f or buying a BISSELL OptiClean ® V acuum We ’re glad y ou purc hased a BISSELL OptiClean v acuum. E verything we kno w about floor care w ent into t he design and cons truction of this com plet e, high-tec h home cleaning sy s tem.
www.bissell.com 800.237.7691 I MPOR T ANT SAFETY INSTR UCTIONS 3 When using an electrical appliance, basic precautions should be obser ved, including the following: READ ALL INSTRUCTIONS BEFORE USING YOUR UPRIGHT V ACUUM. Always connect to a polarized outlet (left slot is wider than right).
4 P roduct view Crevice T ool Extension W and Handle Release Pedal Stretch Hose T urboBrush ® T ool (30C7 model) Pet T urboBrush ® T ool (30C7T model) Carr y Handle Upper T ank Easy Empty Dirt Conta.
www.bissell.com 800.237.7691 A ssembly The only tool you’ll need to assemble your vacuum cleaner is a Phillips head screwdriver . Attach handle to vacuum 1. Locate the bag that contains the extension wand support, lower cord wrap, and screws. Remove the screw packet from the bag.
www.bissell.com 800.237.7691 A ssembly 6 5. Make sure that crevice tool is inside the extension wand. Store the extension wand and crevice tool on the back of the unit. Place tools on the extension wand support and push toward the back of the unit until clip holds tools in place.
Brush Switch The rotating brush is turned on or off using the switch located next to the power switch on the top of the tank. When the brush switch is on, the brush will start rotating when the unit is reclined. The brush should be on for most carpeted floors.
Using the tools Attach desired tool to hose for above floor cleaning surfaces or hard to reach areas. 1. Remove Hose: With vacuum in upright posi - tion, remove hose end from the suction inlet near the bottom of the vacuum by the wheel. Do not remove “tabbed” end of hose con - nected to the clear tank.
www.bissell.com 800.237.7691 9 O perations Empty dirty container Empty the dirt container as soon as the dirt reaches the “full” line on the side of the container . 1. Unplug the vacuum from electrical outlet. 2. Slide the Lock 'n Seal Lever to the “ Unlock ” position.
www.bissell.com 800.237.7691 M aintenance and care 10 Cleaning the pre-motor filter The pre-motor filter should be checked often and washed as needed to maintain performance. More or less frequent cleaning may be required based on individual vacuuming habits and types of debris picked up.
www.bissell.com 800.237.7691 11 M aintenance and care Clearing Clogs Low suction or poor pickup may be due to a clog in the vacuum cleaner . If you notice a change in the sound of the motor or a reduction in the spinning action in the dirt container , check for a clog.
www.bissell.com 800.237.7691 M aintenance and care 12 Thermal motor protection An internal thermal protector has been designed into your cleaner to protect it from overheating. When the thermal protector activates, the main vacuum motor will stop operating.
www.bissell.com 800.237.7691 13 M aintenance and care Y ou should check your vacuum cleaner ’ s r otating floor brush and drive belt regularly for wear and damage. Y ou should also clean the brush and brush ends of strings, hair , and carpet fibers.
www.bissell.com 800.237.7691 M aintenance and care 14 Replace drive belt 1. Unplug the vacuum from electrical outlet. 2. With rotating floor brush removed from vacuum cleaner (steps 1 – 4 of check rotat - ing floor brush and drive belt page13), grasp old drive belt and remove from motor pulley .
www.bissell.com 800.237.7691 15 M aintenance and care T urboBrush T ool maintenance The T urboBrush T ool should be checked regularly for clogs or debris wrapping around the brush. Note: Model 30C7T comes with the Pet T urboBrush T ool and follows same maintenance instructions.
www.bissell.com 800.237.7691 T roubleshooting www.bissell.com 800.237.7691 16 V acuum cleaner won’ t turn on Possible causes Remedies 1. Power cord not plugged in 1. Check electrical plug 2. Blown fuse/tripped breaker in home 2. Check/replace fuse or reset breaker 3.
www.bissell.com 800.237.7691 17 T roubleshooting V acuum cleaner is difficult to push Possible causes Remedies 1. Incorrect height setting 1. Adjust powerfoot to correct height setting see, page 7 Visible dir t escaping from cleaner Possible causes Remedies 1.
www.bissell.com 800.237.7691 R eplacement parts - BISSELL vacuum 18 A dditional accessories Item Part No. Part Name 1 203-1520 Drive Belt 2 20 3 -1 51 2 Foot Brush Roll 3 203-1509 Pre-Motor Foam Filte.
www.bissell.com 800.237.7691 19 W arr anty - BISSELL OptiClean ® V acuum This warranty gives you specific legal rights, and you may also have other rights which may var y from state to state.
Registering is quick, easy and offers you benefits over the lifetime of your product. Y ou’ll receive: BISSELL Rewards Points Automatically earn points for discounts and free shipping on future purchases. Faster Service Supplying your information now saves you time should you need to contact us with questions regarding your product.
An important point after buying a device Bissell 30C7 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bissell 30C7 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bissell 30C7 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bissell 30C7 you will learn all the available features of the product, as well as information on its operation. The information that you get Bissell 30C7 will certainly help you make a decision on the purchase.
If you already are a holder of Bissell 30C7, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bissell 30C7.
However, one of the most important roles played by the user manual is to help in solving problems with Bissell 30C7. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bissell 30C7 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
