Instruction/ maintenance manual of the product 1698 Bissell
Go to page of 17
1698 POWERSTEAMER® PROHEA T TM PLUS SERIES ■ Assembly ■ Operation ■ Safety ■ Storage SmartClean ® System pre-treats, loosens, and lifts out dirt.
■ Keep openings free of dust, lint, hair , etc. ■ Use only commercially available floor cleaners and waxes intended for machine application ■ Keep appliance on a level surface ■ T urn off all .
3 4 1. 2. 3. 4. 5. 6. 7. Slide upper handle onto lower handle. Feed bundled power cord through tool caddy from caddy’ s flat side. Align handle holes and tool caddy holes. Place hex nut into back of tool caddy and hold in place. Insert bolt from front to back turning into hex nut until snug.
SmartT emp ™ T emperature control automatically heats the cleaning solution as it is being applied to the carpet (*) to safely optimize cleaning effectiveness. • The SmartT emp ™ Ready Light indicates when the heater is ON and ready to clean. It is found on the front of the handle where it is easy to see while you clean.
SmartMix ® Provides custom control for each cleaning job. 1. Lift the SmartMix ® concentrate bottle up out of the machine base. 2. Flip the bottle over so that the valve cap is in an upward position. 3. Unscrew the valve cap and fill the bottle to the mark with BISSELL cleaning solution.
7 NOTE: Both the SmartMix ® Bottle and the clean water tank must have liquid in them in order for the machine to spray . If one tank is empty the machine will not apply either cleaning solution or water only . If you’re using the W A TER ONL Y setting, fill the SmartMix ® Bottle with water also.
T i g h t e n R e l e a s e 8 4. Set the tank down and rotate the handle forward to unlatch the lid. Lift off and set the lid aside. 5. Find the mouth of the bladder and fill to the bottom of the neck with hot tap water . NOTE: Fill the Bladder with water only .
9 Tip: A special red float device in the tank will cause the cleaner to stop removing solution from the carpet and the motor sound will rise in pitch to let you know the dirty water tank is full. The Flow Indicator This is located on the machine base.
10 1. Plan activities to give carpet time to dry . 2. Remove easily moved furniture from the room (chairs, lamps, coffee tables, etc). 3. V acuum thoroughly to pick up loose debris and pet hair before using the POWERSTEAMER ® PROHEA T ™ PLUS. 4. Plan your cleaning route to leave an exit path.
11 How to clean upholstery and small areas A d s d fd d g h g bv h cv b b j jk n h n b j jk vh g c g h h jj jh ffhl k llgh Manufacturer’ s T ag Tip: Deep cleaning carpeting and upholstery regularly can reduce dust and allergens in your home. Important - Check Upholstery T ags: 1.
12 Cleaning bare floors T ilt Handle Back Carrying Bottom Front Edge of Machine Base Snap T ogether Bare Floor Cleaning T ool Handle Release The Bare Floor T ool provides effective cleaning for linoleum, vinyl, and tile floors. Caution: Do not use on hardwood floors.
13 Machine Preparation 1 2. Set up machine following instructions in The Basics section, pages 5-9. Be sure to thoroughly rinse out any remaining cleaning solution to prevent slippery linoleum, vinyl, and tile floors. Use BISSELL floor cleaning chemical in the SmartMix ® tank.
1. T urn Power and SmartT emp ™ switches OFF . 2. Unplug power cord from the outlet and coil around machine cord wrap. 3. Remove and rinse tools in clean, running water , dry and replace in tool caddy . 4. Coil flex hose around storage brackets on tool caddy .
SmartT emp ™ Ready Light does not illuminate. Possible Causes Remedies The SmartT emp ™ switch is T urn On the SmartT emp ™ switch. not turned ON. The machine Power Switch is Both switches must be ON to activate the not turned ON. SmartT emp ™ Ready Light.
16 Dirtlifter ® PowerBrush does not turn. Possible Causes Remedies The Brush Belt or Pump Belt T urn the machine OFF and unplug from the may be broken. outlet. T o check if a Brush Belt has broken, you will need a flat head screwdriver . Insert the blade end into the lower slot of the Belt Access door to release the lower snap.
17 Item Part No. Part Name 1 010-9201 4” Small Area T ool 2 603-0910 6” Stair T ool 3 010-9148 Spraying Crevice T ool 4 010-1185 T urboBrush ™ 5 014-9131 Bare Floor T ool 6 014-9142 PreT reat Wa.
18 About your warranty One Y ear Warranty BISSELL Ltd., or an Authorized BISSELL Service Centre will repair or replace, free of charge, any part which is defective or malfunctioning within 1 year of the purchase date, provided that it is used for personal and not commercial or rental service.
An important point after buying a device Bissell 1698 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bissell 1698 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bissell 1698 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bissell 1698 you will learn all the available features of the product, as well as information on its operation. The information that you get Bissell 1698 will certainly help you make a decision on the purchase.
If you already are a holder of Bissell 1698, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bissell 1698.
However, one of the most important roles played by the user manual is to help in solving problems with Bissell 1698. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bissell 1698 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
