Instruction/ maintenance manual of the product IES-1000 ZyXEL Communications
Go to page of 313
IES-1000 Integrated Ethernet Switch Version 2.05 11/2005 User’s Guide.
IES-1000 User ’s Guide ii Copyright Copyright Copyright © 2005 by ZyXEL Communications Corporation. The contents of this publication may not be reproduced in any part or as a whole, transcribed, st.
IES-1000 User ’s Guide Interference S tatement s and W arnings iii Interference S t atement s and W arnings FCC Interference Statement: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference.
IES-1000 User ’s Guide iv W arranty ZyXEL Limited W arranty ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in materials or workmanship for a period of up to two years from the date of purchase.
IES-1000 User ’s Guide Customer Support v Customer Support Please have the following information read y when you contact customer support. Product model and serial number. Warranty information. Date that you received your device. Brief description of the problem and the steps you took to solve it.
IES-1000 User ’s Guide vi W arranty support@zyxel.es +34-902-195-4 20 Spain sales@zyxel.es +34-913-005-345 www.zyxel.es ZyXEL Communications Alejandro Villegas 33 1º, 28043 Madrid Spain support@zyxel.se +46-31-744-7700 Sweden sales@zyxel.se +46-31-744-7701 www.
IES-1000 User ’s Guide T able of Contents vii T able of Content s Copyri ght ...................................................................................................................... ............................................. ii Interference S tatem ents and W arnings .
IES-1000 User ’s Guide viii T able of Contents 5.1 Removing a G.SHDSL SAM1008 Network Module ............................................................................ 5-1 5.2 Installing a Network Module ...........................................
IES-1000 User ’s Guide T able of Contents ix 10.3 Bridge Overview ................................................................................................................ ................. 10-2 10.4 Bridge Setup Screen ......................
IES-1000 User ’s Guide x T able of Contents Chapter 15 VLAN........................................................................................................................... ................. 15-1 15.1 VLAN Over view .......................
IES-1000 User ’s Guide T able of Contents xi 21.6 Configured Settings ............................................................................................................ ................. 21-2 21.7 Password .................................
IES-1000 User ’s Guide xii T able of Contents 27.2 Ethernet Commands .............................................................................................................. .............. 27-1 Chapter 28 Bridge Co mmands .....................
IES-1000 User ’s Guide T able of Contents xiii 35.1 Configuration Files of the Network Module ...................................................................................... . 35-1 35.2 Configuration Backup ...................................
IES-1000 User ’s Guide xiv List of Figures List of Figures Figure 1-1 MTU Application ..................................................................................................... .................................. 1-5 Figure 1-2 Central Office or ISP Application .
IES-1000 User ’s Guide List of Figures xv Figure 9-2 Ho me Screen ......................................................................................................... .................................. 9-2 Figure 9-3 Bridge Setup Example ......
IES-1000 User ’s Guide xvi List of Figures Figure 12-3 G .SHDS L Profile Setup .............................................................................................. .......................... 12-6 Figure 12-4 G .S HDSL Add Profile .........
IES-1000 User ’s Guide List of Figures xvii Figure 20-3 Reboot Sy stem Conf irmation ......................................................................................... ...................... 20-6 Figure 20-4 Logout ...........................
IES-1000 User ’s Guide xviii List of Figures Figure 33-1 Setting IP Addr ess and Defaul t Gateway ............................................................................. ................ 33-2 Figure 36-1 BOOT P/TFTP Server ....................
IES-1000 User ’s Guide List of T able s xix List of T ables T able 3-1 Front Panel Ports of the SAM1008 Ne twork Module ...................................................................... .......... 3-2 T able 3-2 Front Panel Ports of the AAM1008 Ne twork Module .
IES-1000 User ’s Guide xx List of T able s T able 10-18 Bridge Fast Mode VLAN ID Setup ..................................................................................... ................ 10-21 T able 10-19 IP Setup ...............................
IES-1000 User ’s Guide List of T able s xxi T able 19-2 Hard ware Monitor .................................................................................................... .............................. 19-2 T able 19-3 Port S tatistics .........
IES-1000 User ’s Guide xxii Preface Preface Congratulations on your purchase of the IES-1000 Integrated Ethernet Switch. About this User ’ s Manual This user’s guide explains how to: Install.
IES-1000 User ’s Guide Preface xxiii Please refer to www.zy xel.com for an online glossary of networking terms or the ZyXEL download library for additional support documentation. Online Registration Register your product online at www.zyxel.com for global products, or at www.
Overview and Installation I Part I: Overview and Installation This part introduces the general features, defaul t settings, hardware and installation of the IES- 1000 Integrated Ethernet Switch.
.
IES-1000 User ’s Guide Getting to Know the IES-1000 1-1 Chapter 1 Getting to Know the IES-1000 This chapter describes the key features, benefits and applica tions of your IES-1000. The IES-1000 (Integrated Ethernet Switch) is an IP-based DSLAM (Internet Protocol Digital Subscriber Line Access Multiplexer) that connects up G.
IES-1000 User ’s Guide 1-2 Getting to Know the IES-1000 G.lite (ITU-T G.992.2) G.hs (ITU-T G.994.1) ANSI T1.413 issue 2 ETSI (TS 101 388) • Rate adaptation support N-wire Mode (SAM1008) The n-wire mode allows you to physically bundle two or four G.
IES-1000 User ’s Guide Getting to Know the IES-1000 1-3 You can limit the number of MAC addresses that may be dy namically learned or statically configured on a port. You may enable/disable the MAC count filter on individual ports. IEEE 802.1X Port-based Authentication The IES-1000 supports the IEEE 802.
IES-1000 User ’s Guide 1-4 Getting to Know the IES-1000 Overheating Detection, W arning and Safegaurd An ALM LED turns on when the IES-1000’s internal temper ature is too high and turns off when the tem perature has returned to a normal level. Internal fans cool the unit.
IES-1000 User ’s Guide Getting to Know the IES-1000 1-5 Figure 1-1 MTU Application.
IES-1000 User ’s Guide 1-6 Getting to Know the IES-1000 1.2.2 Central Of fice or ISP Application The IES-1000 provides DSL service over telephone wires to subscribers. The following figure shows the IES- 1000 set up in an Internet Service Provider (ISP) building or teleph one company central office.
IES-1000 User ’s Guide Factory Default Settings 2-1 This section describes the factory default settin gs of the IES-1000. 2.1 IP Parameters • IP address = 192.
IES-1000 User ’s Guide 2-2 Factory Default Settings • Enable/Disable State: Disabled • Profile: DEFVAL Maximum upstream/downstream speed: 2304 Kbps Minimum upstream/downstream speed: 192 Kbps 2.
IES-1000 User ’s Guide Factory Default Settings 2-3.
.
IES-1000 User ’s Guide Hardware Overview 3-1 This chapter gives a brief introductio n to the IES-1000 hardware. 3.1 Additional Inst allation Requirements A computer with Ethernet 10Base-T or 100Base.
IES-1000 User ’s Guide 3-2 Hardware Overview 3.3.1 Network Module Front Panel LEDs See the Turning On the IES-1000 chapter for details on the LED indicators on t he front panel of a SAM1008 or AAM1008 network module. 3.3.2 Front Panel Port s The following tables describe front panel ports.
IES-1000 User ’s Guide Hardware Installation 4-1 This chapter shows you how to install hardware for a freestanding or rack-m ounted scenario. 4.1 Environment The following are the recommended environments for the IES-1000. 4.1.1 Operating Environment Temperature: 0 — 50°C; Humidity: 5% — 95% (non-condensing) 4.
IES-1000 User ’s Guide 4-2 Hardware Installation 4.4.1 Att aching the Mounting Bracket s to the IES-1000 Step 1. Position a mounting bracket on one side of the IES-1000, lining up the four screw holes on the bracket with the screw holes on the side of the unit (see the figure shown next).
IES-1000 User ’s Guide Hardware Installation 4-3 Figure 4-2 Mounting the IES-1000 on a Rack Step 2. Using a #2 Philips screwdriver, install the M5 flat head screws through the mounting bracket holes into the rack. Step 3. Repeat Step 1 and Step 2 to attach the second mounting bracket on t he other side of the rack.
.
IES-1000 User ’s Guide Removing and Installing Network Modules 5-1 This chapter shows you how to remove and install network modules. Each IES-1000 accommodates up to two network modules.
IES-1000 User ’s Guide 5-2 Removing and Installing Network Modules Figure 5-3 Removing a Network Module from the IES-1000 Chassis 5.2 Inst alling a Network Module Step 1. Hold the module with the network ports facing you an d insert it into an empty slot located on the front of the IES-1000 as shown next.
IES-1000 User ’s Guide Removing and Installing Network Modules 5-3 Figure 5-4 Installing a Network Module into the IES-1000 Chassis The front of the network module must be flush with the front of the IES-1000 after you install a network module or it will not work! Step 3.
Hardware Connections II Part II: Hardware Connections and Troubleshooting This part covers how to connect the IES-1000 and tu rn it on. It also cove rs how to troubleshoot the hardware.
IES-1000 User ’s Guide Hardware Connections 6-1 This chapter shows you how and where to make hardware connections. Before you make your hardware connections, make su re that your IES-1000 is safely and securely positioned. 6.1 Front Panel Connections All connections are made on the front panel of th e IES-1000.
IES-1000 User ’s Guide 6-2 Hardware Connections Figure 6-2 Console Port Connection 6.3 SHDSL Port Connections The SHDSL ports connect to an MDF (Main Distribution Frame) and end-user equipment via telephone wires. • For detailed specifications about the associated RJ-11 connector, refer to the Pin Assignment appendix.
IES-1000 User ’s Guide Hardware Connections 6-3 Figure 6-3 SHDSL Port and MDF Connections Step 3. Connect a different telephone wire to the lowe r port of the MDF using a punch-down tool. Step 4. Connect the other (RJ-11) end of the telephone wire to the end-user G.
IES-1000 User ’s Guide 6-4 Hardware Connections Figure 6-4 SHDSL Port, MDF and User Equipment Connections Notes About MDFs (Main Distribution Frames) An MDF is usually installed between end-users’ equipment and the telephone company (CO) in a basement or telephone room.
IES-1000 User ’s Guide Hardware Connections 6-5 Figure 6-5 Magnified View of MDF Wiring Connect wiring from end-user equipment to the lower por ts of an MDF using a telephone wire. Connect wiring from the telephone company to the upper ports of an MDF (see the previous figure).
IES-1000 User ’s Guide 6-6 Hardware Connections Figure 6-6 AAM1008 Installation Overview You can also use RJ-11 connectors on both ends of the telephone cables connect directly to an ADSL modem(s) or patch panel. This chapter discusses connections using MDFs.
IES-1000 User ’s Guide Hardware Connections 6-7 Figure 6-7 Installation Scenario A Procedure T o Connect T o An MDF Step 1. Connect the RJ-11 connector end of a telephone wire to one of the USER ports on the AAM1008. Step 2. Connect the other end of the telephone wire to th e upper ports of the MDF using a punch-down tool.
IES-1000 User ’s Guide 6-8 Hardware Connections Figure 6-8 One MDF for End-user and CO Connections Please refer to the following figure for the connection schema. MDF 1 is the original MDF used for telephone connections only. MDF 2 is used for telephone connections only.
IES-1000 User ’s Guide Hardware Connections 6-9 Figure 6-9 Installation Scenario B Procedure T o Connect T o MDFs Step 1. Acquire two additional MDFs (MDFs 2 and 3). Step 2. Connect the RJ-11 connector ends of telephone wires you want for ADSL service to the USER ports on the AAM1008.
IES-1000 User ’s Guide 6-10 Hardware Connections 6.4.4 Inst allation Scenario C Phone service is also available but there are two MDFs; one for end-user telephone lin e connections and the other one for CO telephone line connections (see the following figure).
IES-1000 User ’s Guide Hardware Connections 6-1 1 Figure 6-11 Installation Scenario C Procedure T o Connect T o MDFs Step 1. Acquire two additional MDFs (3 and 4). Step 2. Connect the RJ-11 connector ends of telephone wires you want for ADSL service to the USER ports on the AAM1008.
IES-1000 User ’s Guide 6-12 Hardware Connections Connect the top ports of MDF 1 to the telephone company. 6.4.5 LAN Port (Ethernet) Connection Connect the LAN port of your SAM1008 to an Ethernet WAN switch using a st raight-through Category 5 UTP (Unshielded Twisted Pair) cable with RJ -45 connectors.
IES-1000 User ’s Guide Hardware Connections 6-13 Figure 6-13 Connecting the Power Cord to the IES-1000 and a Power Source 6.6 DC Power Model Power Connections Use the following procedures to connect the IES-1000 to a power source after you have installed the IES-1000 in a rack.
IES-1000 User ’s Guide 6-14 Hardware Connections Figure 6-14 Connecting IES-1000 Power.
IES-1000 User ’s Guide T urning On the IES-1000 7-1 Chapter 7 Tu r n i n g On the IES-1000 This chapter discusses the fans and LEDs of the IES-1000 after you turn it on. 7.1 Introduction Before turning on your IES-1000, m ake sure you: • Have attached a computer to the IES-1000 serial port as explained previously.
IES-1000 User ’s Guide 7-2 T urning On the IES-1000 Figure 7-2 SAM1008 Front Panel LEDs Figure 7-3 AAM1008 Front Panel LEDs Table 7-1 Network Module LED Descriptions LED COLOR STATUS DESCRIPTION ALM Red On The module has overheated. Off The module is functio ning within normal temperature para meters.
IES-1000 User ’s Guide Hardware T roubleshooting 8-1 This chapter explains how to troubleshoot IES-1000 hardware. 8.1 System S tartup When you turn on the IES-1000, it automatically runs a self-test that takes approximately 20 seconds. The SYS LED will remain on if your IES-1000 has started normally.
IES-1000 User ’s Guide 8-2 Hardware T roubleshooting 8.3 The SHDSL LED(s) Do Not T urn On The SHDSL LEDs show the operational status of SHDSL port co nnections. If the SHDSL LED is off, it means the link to the SHDSL modem/router is down or there is not a connection to the SHDSL po rt.
IES-1000 User ’s Guide Hardware T roubleshooting 8-3 Table 8-4 ADSL LED Troubleshooting STEP CORRECTIVE ACTION 10 Repeat the steps above us ing a different ADSL port.
IES-1000 User ’s Guide 8-4 Hardware T roubleshooting tests to be done. Suppose you’re using installation scenar io “B” as shown in the chapter on MDF connections. The logic for other scenarios should be similar. Use steps A-D if there is no voice but you can transmit da ta.
IES-1000 User ’s Guide Hardware T roubleshooting 8-5 Table 8-7 Testing In-house Wiring STEP TEST C Disconnect the telephone wire from CO . Conne ct a telephone to the telephone wire. If there is no dial tone, then the probl em is between your devi ce and MDF 2.
Getting S tarted III Part III: Getting Started This part tells how to access and navigate the w eb configurator . It also describes the Getting S tarted web configurator screens.
.
IES-1000 User ’s Guide Web Configurator Access and Navigation 9-1 This chapter describes how to log into the web configurator and navigate through it.
IES-1000 User ’s Guide 9-2 W eb Configurator Access and Navigation 9.3 Home Screen This is the web configurator home screen. Click a link on t he navigation panel to go to the corresponding s creen.
IES-1000 User ’s Guide Web Configurator Access and Navigation 9-3 Table 9-1 Navigation Panel Links LABEL DESCRIPTION Diagnostic This link takes you to a screen wher e you can view error logs and test the DSL connectio ns. Config Save Click this link to save your changes to the device’ s non-volatile memory.
IES-1000 User ’s Guide 9-4 W eb Configurator Access and Navigation 9.5 Saving Y our Configuration Click Apply in a configuration screen to save your changes back to the IES-1000’s volatile memory. The IES- 1000 loses these changes if it is turned off or loses power.
IES-1000 User ’s Guide Web Configurator Access and Navigation 9-5 Click the Packet Type Filter to go down one level to the Packet Type Filter Setup screen (shown next).
.
IES-1000 User ’s Guide Getting S tarted Screens 10-1 This chapter explains the General Setup and Bridge Setup screens. 10.1 Getting S tarted Overview The web configurator allows you to configure basic settings using the Getting Started screens. 10.2 General Setup Screen Click General Setup in the navigation panel to open t his screen.
IES-1000 User ’s Guide 10-2 Getting S tarted Screens Table 10-1 General Setup LABEL DESCRIPTION Slot ID Type 1 or 2 for the slot ID number. The sl ot ID help s keep track of this individual network module. Apply Click Apply to save your changes back to the IES-1000's volatile memory.
IES-1000 User ’s Guide Getting S tarted Screens 10-3 Figure 10-2 Bridge Setup The following table describes this screen. Table 10-2 Bridge Setup LABEL DESCRIPTION Operating Mode Bridge Mode Choose Normal or Fast from the drop-down list box. The Normal mode supports 802.
IES-1000 User ’s Guide 10-4 Getting S tarted Screens Table 10-2 Bridge Setup LABEL DESCRIPTION MAC Count Filter Click this link to go to a scr een for setting limits on how many MAC addres ses may be dynamically learned or stat ically configured on a port.
IES-1000 User ’s Guide Getting S tarted Screens 10-5 Table 10-3 Bridge Packet Type Filter Setup LABEL DESCRIPTION Packet Filter Type Choose Any or IP or PPPoE from the drop-do wn list. Choose Any to allow all kinds of packets, IP to allow IP packets only or PPPoE to allow PPPoE packe ts only.
IES-1000 User ’s Guide 10-6 Getting S tarted Screens Figure 10-4 Default Port Filter Settings 10.5.1 Port Filter Setup Screen Click Port Filter in the Bridge Setup screen to open this screen. Figure 10-5 Bridge Port Filter Setup The following table describes this screen.
IES-1000 User ’s Guide Getting S tarted Screens 10-7 Figure 10-6 Edit Bridge Port Filter Setup The following table describes this screen. Table 10-5 Edit Bridge Port Filter Setup LABEL DESCRIPTION Bridge Setup Click this link to go to the Bridge Setup screen.
IES-1000 User ’s Guide 10-8 Getting S tarted Screens Figure 10-7 Bridge MAC Filter Setup The following table describes this screen. Table 10-6 Bridge MAC Filter Setup LABEL DESCRIPTION Bridge Setup Click this link to go to the Bridge Setup screen. Port Number Click the port name to edit that port’s MAC filter setup.
IES-1000 User ’s Guide Getting S tarted Screens 10-9 Table 10-7 Bridge MAC Filter Entry List LABEL DESCRIPTION Bridge Setup Click this link to go to the Bridge Setup screen. Bridge MAC Filter Setup Click this link to go to the Bridge MAC Filter Setup screen.
IES-1000 User ’s Guide 10-10 Getting S tarted Screens Table 10-8 Bridge MAC Filter Entry Add LABEL DESCRIPTION Apply Click Apply to save your changes back to the IES-1000's volatile memory.
IES-1000 User ’s Guide Getting S tarted Screens 10-1 1 Table 10-9 MAC Count Filter Setup LABEL DESCRIPTION Max Static MAC Count This field’s first number displays how ma ny MA C addresses are statically spe cified for a port. This field’s second number displays the limit of how many MAC addresses may be statically specified on the port.
IES-1000 User ’s Guide 10-12 Getting S tarted Screens Table 10-10 MAC Count Filter Edit LABEL DESCRIPTION Max Static MAC Count Use this field to limit the number of MAC addresses that may be statically specifi ed for this port.
IES-1000 User ’s Guide Getting S tarted Screens 10-13 The following table describes this screen. Table 10-11 Bridge MAC Address Record LABEL DESCRIPTION Bridge Setup Click this link to go to the Bridge Setup screen. Setup Aging Time Enter a time from 10 to 1,000,000 seconds.
IES-1000 User ’s Guide 10-14 Getting S tarted Screens Figure 10-13 Bridge IGMP Snooping Record The following table describes this screen. Table 10-12 Bridge IGMP Snooping Record LABEL DESCRIPTION Bridge Setup Click this link to go to the Bridge Setup screen.
IES-1000 User ’s Guide Getting S tarted Screens 10-15 Table 10-12 Bridge IGMP Snooping Record LABEL DESCRIPTION Member Ports This field di splays the ports that bel ong to this multicast grou p, E=Et hernet, 1~8 = ADSL ports 1 through 8. Refresh Click this button to update the multicast filtering record.
IES-1000 User ’s Guide 10-16 Getting S tarted Screens 10.5.11 DHCP Relay Screen Click DHCP Relay in the Bridge Setup screen to open this screen. Figure 10-15 DHCP Relay Setup Table 10-13 DHCP Relay Setup LABEL DESCRIPTION Bridge Setup Click this link to go to the Bridge Setup screen.
IES-1000 User ’s Guide Getting S tarted Screens 10-17 Figure 10-16 Add DHCP Server Table 10-14 Add DHCP Server LABEL DESCRIPTION Bridge Setup Click this link to go to the Bridge Setup screen. DHCP Relay Setup Click this link to go to the DHCP Relay Setup scree n.
IES-1000 User ’s Guide 10-18 Getting S tarted Screens the memory capacity of the device. In essence, RADIUS authentication allows you to validate an unlimited number of users from a central location. Figure 10-17 RADIUS Server 10.5.13 802.1X Setup Sc reen Click 802.
IES-1000 User ’s Guide Getting S tarted Screens 10-19 Table 10-15 802.1X Setup LABEL DESCRIPTION Control When this field displays Auto , the IES-1000 authenticates all subscribers before they can access the network through this port.
IES-1000 User ’s Guide 10-20 Getting S tarted Screens Table 10-16 RADIUS Server Setup LABEL DESCRIPTION Shared Secret Specify a password (up to 31 alphanumer ic cha racters) as the key to be shared between the external RADIUS server and the IES-1000.
IES-1000 User ’s Guide Getting S tarted Screens 10-21 Table 10-17 Edit 802.1x Setup LABEL DESCRIPTION Reauthentication Select ( On ) if a subscriber has to periodi cally re-enter his or her usernam e and password to stay connected to the port.
IES-1000 User ’s Guide 10-22 Getting S tarted Screens Table 10-18 Bridge Fast Mode VLAN ID Setup LABEL DESCRIPTION Port Number This is the port's name. VLAN ID Enter a VLAN ID number for the port. The valid range is 1-4094. You can not configure more than one port to use the same VLAN ID.
IES-1000 User ’s Guide Getting S tarted Screens 10-23 Table 10-19 IP Setup LABEL DESCRIPTION Default Gateway Enter the IP address of the default-outgoing gatew ay in dotted de cimal notation, for example 192.168.1.254. Apply Click Apply to save your changes back to the I ES-1000's volatile memory.
.
IES-1000 User ’s Guide ADSL Module Port Setup 11 - 1 This chapter explains how to configure individual ports on the AAM-1008. 11.1 ADSL Module Port Setup Overview The web configurator allows you to configure settings for the ADSL Access Module’s ports.
IES-1000 User ’s Guide 11 - 2 ADSL Module Port Setup 11.5 Interleave Delay Interleave delay is the wait (in milliseconds) that determines the size of a single block of data to be interleaved (assembled) and then transmitted.
IES-1000 User ’s Guide ADSL Module Port Setup 11 - 3 - Maximum Signal/Noise Ratio: 31 db - Minimum Signal/Noise Ratio: 0 db - Minimum Transmission Rate: 32 Kbps - Maximum Transmission Rate: 2048 Kb .
IES-1000 User ’s Guide 11 - 4 ADSL Module Port Setup Figure 11-1 ADSL Port Setup The following table describes this screen. Table 11-2 ADSL Port Setup LABEL DESCRIPTION Profile Setup Click this link to go to a screen for setting up DSL pro files. Port Number This field shows “0” for the Ethernet port.
IES-1000 User ’s Guide ADSL Module Port Setup 11 - 5 11.8.1 ADSL Profile Setup Screen A profile is a list of settings that you define. Then you can assign them to one or more individual ports. Click the Profile Setup link in the Port Setup screen to go to the Profile Setup screen.
IES-1000 User ’s Guide 11 - 6 ADSL Module Port Setup ADSL Profile Add or Edit Screen Click the Profile Setup link in the Port Setup screen to go to the Profile Setup screen. Click the Add button in the Profile Setup screen to add a new profile or click the name of an existing profile to edit the profile.
IES-1000 User ’s Guide ADSL Module Port Setup 11 - 7 Table 11-4 ADSL Add Profile LABEL DESCRIPTION Min Rate (Kbps) Type the minimum upstream transfer rate (from 3 2 to 1024 Kbps) for this profile. Configu re the minimum upstream transfer rate to be less than the m aximum upstream transfer rate.
IES-1000 User ’s Guide 11 - 8 ADSL Module Port Setup When auto-negotiation is turned on, the Ethernet port of the IES-1000 negotiates with the peer Ethernet port on the Ethernet cable automatically to determine the optimal connection speed and duplex m ode.
IES-1000 User ’s Guide ADSL Module Port Setup 11 - 9 Table 11-5 Ethernet Port Setup LABEL DESCRIPTION Default VLAN ID Type the Port VLAN ID (PVID) from 1 to 4094. The IES-1000 assig ns the PVID to untagged frames or priority frames (0 VID) received on this port.
IES-1000 User ’s Guide 1 1-10 ADSL Module Port Setup Figure 11-5 ADSL Port Setup Edit The following table describes this screen. Table 11-6 ADSL Port Setup Edit LABEL DESCRIPTION Channel Setup Click this link to go to the port's Channel Setup screen.
IES-1000 User ’s Guide ADSL Module Port Setup 11 - 11 Table 11-6 ADSL Port Setup Edit LABEL DESCRIPTION Default VLAN ID Type the Port VLAN ID (PVID) from 1 to 4094. The IES-1000 assig ns the PVID to untagged frames or priority frames (0 VID) received on this port.
.
IES-1000 User ’s Guide G .SHDSL Module Port Setup 12-1 This chapter explains how to configure individual ports on the SAM1008. 12.1 G . SHDSL Module Port Setup Overview The web configurator allows you to configure settings for the G.SHDSL Access Module’s ports.
IES-1000 User ’s Guide 12-2 G .SHDSL Module Port Setup You can n-wire bundle multiple groups of ports on a single IES-1000 (or even within a single SAM1008 m odule) as long as they do not overlap. 12.5 Port Bonding The port bonding feature allows you to send IP packets over two to eight G.
IES-1000 User ’s Guide G .SHDSL Module Port Setup 12-3 12.7 Default G .SHDSL Module Settings The default profile always exists and all of the G.SHD SL ports use the default profile settings when the network module is shipped. The default profile' s name is set to DEFVAL .
IES-1000 User ’s Guide 12-4 G .SHDSL Module Port Setup Figure 12-2 G.SHDSL Port Setup The following table describes this screen. Table 12-2 G.SHDSL Port Setup LABEL DESCRIPTION Profile Setup Click this link to go to a screen for setting up DSL pro files.
IES-1000 User ’s Guide G .SHDSL Module Port Setup 12-5 Table 12-2 G.SHDSL Port Setup LABEL DESCRIPTION Active This field shows whether the port is turned on ( Yes ) or not ( No ). The factory default of all DSL ports is disabled. A port must be enabled for data transmission to occur.
IES-1000 User ’s Guide 12-6 G .SHDSL Module Port Setup Click the Profile Setup link in the Port Setup screen to go to the Profile Setup screen. Figure 12-3 G.SHDSL Profile Setup Table 12-3 G.SHDSL Profile Setup LABEL DESCRIPTION Port Setup Click this link to go to the Port Setup screen.
IES-1000 User ’s Guide G .SHDSL Module Port Setup 12-7 Figure 12-4 G.SHDSL Add Profile Table 12-4 G.SHDSL Add Profile LABEL DESCRIPTION Port Setup Click this link to go to the Port Setup screen. Profile Name When editing a profile, this is the name of this profile.
IES-1000 User ’s Guide 12-8 G .SHDSL Module Port Setup Figure 12-5 G.SHDSL Port Setup The following table describes this screen. Table 12-5 G.SHDSL Port Setup LABEL DESCRIPTION Channel Setup Click this link to go to the port's Channel Setup screen.
IES-1000 User ’s Guide G .SHDSL Module Port Setup 12-9 Table 12-5 G.SHDSL Port Setup LABEL DESCRIPTION Default VLAN ID Type the Port VLAN ID (PVID) from 1 to 4094. The IES-1000 assig ns the PVID to untagged frames or priority frames (0 VID) received on this port.
IES-1000 User ’s Guide 12-10 G .SHDSL Module Port Setup Table 12-6 Add G.SHDSL N-wire Group LABEL DESCRIPTION Port Setup Click this link to go to the Port Setup screen.
IES-1000 User ’s Guide G .SHDSL Module Port Setup 12-1 1 Figure 12-7 Add G.SHDSL Port Bonding Table 12-7 Add G.SHDSL Port Bonding LABEL DESCRIPTION Port Setup Click this link to go to the Port Setup screen. Bonding Name Type a name to identify this port bonding group.
IES-1000 User ’s Guide 12-12 G .SHDSL Module Port Setup Table 12-7 Add G.SHDSL Port Bonding LABEL DESCRIPTION Available Ports /Available Groups When you select a 2-wire mode, the screen displays the available ports (those that are not members of an n-wire grou p or another port bondi ng group).
IES-1000 User ’s Guide Virtual Channel Management 13-1 This chapter shows you how to configure virtual channels. T he configuration of virtual channels is the same for both the AAM1008 and SAM1008 network modules.
IES-1000 User ’s Guide 13-2 Virtual Channel Management 13.1.3 VC Mux VC Mux is a type of encapsulation where, by prior mutual agreement, each protocol is assigned to a specific virtual circuit, for example, VC1 carries IP, VC2 carries IPX, and so on.
IES-1000 User ’s Guide Virtual Channel Management 13-3 Table 13-1 DSL Port Channel Setup LABEL DESCRIPTION Edit Port Setup Click this link to go to the Edit Port Setup screen. Port Setup Click this link to go to the Port Setup screen. VPI/VCI This field displays the Virtual Path Identifie r (VPI) and Virtual Circui t Identifier (VCI).
IES-1000 User ’s Guide 13-4 Virtual Channel Management V ariable Bit Rate (VBR) The Variable Bit Rate (VBR) ATM traffic class is used w ith bursty connections. Connections that use the Variable Bit Rate (VBR) traffic class can be grouped into real time (rt-VBR) or non-real time (nrt-VBR) connections.
IES-1000 User ’s Guide Virtual Channel Management 13-5 Sustained Cell Rate (SCR) Sustained Cell Rate (SCR) is the mean cell rate of eac h bursty traffic source. It specifies the maximum average rate at which cells can be sent over the virtual c onnection.
IES-1000 User ’s Guide 13-6 Virtual Channel Management Burst T olerance (BT) Burst Tolerance (BT) is the maximum number of cells that the port is guaranteed to handle without any discards. BT controls the time scale over which the SCR is enforced. BT is used to determine if a cell arrived too early in relation to SCR.
IES-1000 User ’s Guide Virtual Channel Management 13-7 Figure 13-4 DSL Port VC Profile Setup Table 13-2 DSL Port VC Profile Setup LABEL DESCRIPTION Channel Setup Click this link to go to the Channel Setup screen. Profile Name This name identifies the profile.
IES-1000 User ’s Guide 13-8 Virtual Channel Management DSL Port VC Profile Add or Edit Screen Do the following to open th e VC Profile screen: Step 1. Click a DSL port's index number in the Port Setup screen to go to the DSL Port Setup screen. Step 2.
IES-1000 User ’s Guide Virtual Channel Management 13-9 Table 13-3 DSL Port VC Profile Add LABEL DESCRIPTION Class Select cbr (constant bit rate) to specify fixed (alwa ys-on) bandwidth for voice or data traffic. Select ubr (unspecified bit rate) for application s that are non-time sensitive, such as e-mail.
IES-1000 User ’s Guide 13-10 Virtual Channel Management Figure 13-6 DSL Port Channel Add Table 13-4 DSL Port Channel Add LABEL DESCRIPTION Channel Setup Click this link to go to the port's Channel Setup screen. VPI Type the Virtual Path Identifier for this port.
IES-1000 User ’s Guide Virtual Channel Management 13-1 1 Table 13-4 DSL Port Channel Add LABEL DESCRIPTION Apply Click Apply to save your changes back to the I ES-1000's volatile memory.
Advanced Applications and Management IV Part IV: Advanced Applications and Management This part describes the Advanced Applications and Advanced Management web configurator screens and troubleshooting.
IES-1000 User ’s Guide S tatic Route 14-1 This chapter explains how to configure static rout es for the IES-1000. 14.1 S tatic Route Overview The web configurator allows you to set up static routes that tell the IES-1000 how to forward management traffic when you configure the TCP/IP parameters manually.
IES-1000 User ’s Guide 14-2 S tatic Route 14.2.1 Add S tatic Route Screen Click Static Route Setup in the navigation panel to open the Static Route screen and then click Add to open this screen. Use this menu to configure a static route. Figure 14-2 Add Static Route The following table describes this screen.
IES-1000 User ’s Guide S tatic Route 14-3 Table 14-2 Add Static Route LABEL DESCRIPTION Apply Click Apply to save your changes back to the IES-1000's volatile memory.
.
IES-1000 User ’s Guide VLAN 15-1 This chapter explains how to configure VLANs on the IES-1000. 15.1 VLAN Overview A VLAN (Virtual Local Area Network) allows a physical ne twork to be partitioned into multiple logical networks. Stations on a logical network belong to one group.
IES-1000 User ’s Guide 15-2 VLAN TPID 2 Bytes User Priority 3 Bits CFI 1 Bit VLAN ID 12 bits TPID has a defined value of 8100 (hex). The first three bits of the TCI define user priority (giving eight priorit y levels). The CFI (Canonical Format Indicator) is a single- bit flag, always set to zero for Ethernet switches.
IES-1000 User ’s Guide VLAN 15-3 added and deleted using GARP VLAN Registration Protocol (GVRP), where GARP is the Generic Attribute Registration Protocol. 15.5 Automatic VLAN Registration GARP and GVRP are the protocols used to automati cally register VLAN membership across switches.
IES-1000 User ’s Guide 15-4 VLAN Table 15-1 GARP Terminology Port VID This is the VLAN ID assi gned to untagged frames that this port received (in Port Setup). Acceptable Frame Type Whether tagged only or both untagged frames a re accepted on this port.
IES-1000 User ’s Guide VLAN 15-5 Table 15-2 Static VLAN Setup LABEL DESCRIPTION Management VLAN ID The management VLAN ID is the number of the VLAN through which you manage the IES- 1000. The management VLAN defines which ports you can use to manage the IES-1000.
IES-1000 User ’s Guide 15-6 VLAN The following table describes this screen. Table 15-3 Add VLAN Static Entry LABEL DESCRIPTION VLAN Setup Click this link to go to the Static VLAN Setup screen. VLAN ID This is the ID number of VLAN group index number you clicked in the Static VLAN Setup page.
IES-1000 User ’s Guide SNMP 16-1 This chapter explains how to configure Simple Network Management Protocol (SNMP). 16.1 SNMP Management SNMP (Simple Network Management Pr otocol) is a protocol used for exchanging m anagement information between network devices.
IES-1000 User ’s Guide 16-2 SNMP Base (MIB) is a collection of managed objects. SNMP a llows manager and agents to communicate for the purpose of accessing these objects. SNMP itself is a simple request/response protocol based on the manager/agent model.
IES-1000 User ’s Guide SNMP 16-3 16.2 SNMP Setup Screen Click SNMP in the navigation panel to open the SNMP screen. Figure 16-2 SNMP Setup The following table describes this screen. Table 16-2 SNMP Setup LABEL DESCRIPTION Trust Host The trusted host, your IES-1000 will only respond to SNMP messages from this addre ss.
IES-1000 User ’s Guide 16-4 SNMP Figure 16-3 Add SNMP Access Entry The following table describes this screen. Table 16-3 Add SNMP Access Entry LABEL DESCRIPTION SNMP Setup Click this link to go to the SNMP Setup page. Trusted Host If you enter a trusted host, your IES-1000 w ill only respond to SNMP messages from this address.
IES-1000 User ’s Guide Logins 17-1 This chapter explains how to change the IES-1000’s passwords. 17.1 Logins Overview The Logins screen allows you to configure the administrator password. 17.2 Logins Screen Click Logins in the navigation panel to open the Logins screen.
IES-1000 User ’s Guide 17-2 Logins Table 17-1 Logins LABEL DESCRIPTION Apply Click Apply to save your changes back to t he IES-1000's volatile memory.
IES-1000 User ’s Guide Maintenance 18-1 This chapter explains how to use the maintenance screens to set the Unix syslog parameters and remote management; as well as perform firmware and configuration file maintenance. 18.1 Maintenance Overview The Maintenance screen allows you to set UNIX sy slog parameters.
IES-1000 User ’s Guide 18-2 Maintenance Table 18-1 Maintenance LABEL DESCRIPTION Backup Configuration Use the Backup link to save your cu rrent configuration to a computer. UNIX System Log Select this check box to activate syslog (UNIX system loggin g ) and then configure the UNIX syslog parameters d escribed in the following fields.
IES-1000 User ’s Guide Maintenance 18-3 Table 18-2 Secured Client Setup LABEL DESCRIPTION Secured Enable Select this check box to allow these secured client s to manage the IES-1000. Do not select this check box unless the IP address that you are usi ng to manage the IES-1000 is already configured as one of the cli ent addresses below.
IES-1000 User ’s Guide 18-4 Maintenance Table 18-3 Add Secured Client LABEL DESCRIPTION Secured Client Setup Click this link to go to the Secured Client Setup screen. Secured Client Address Set the IP address of a computer that you want to allow Telnet, FTP or Web access to this IES- 1000.
IES-1000 User ’s Guide Maintenance 18-5 Figure 18-4 Firmware Upgrade 18.2.3 Restore Configuration Screen Click Maintenance in the navigation panel and then Restore Configuration to open the Restore Configuration screen. Use the Restore Configuration screen to restore a previously saved configuration from your computer to the IES- 1000.
IES-1000 User ’s Guide 18-6 Maintenance 18.2.4 Backup Configuration Screen Click Maintenance in the navigation panel and then Backup Configuration to open the Backup Configuration screen. Use the Backup Configuration screen to save the current configuration of the IES-1000 to a computer.
IES-1000 User ’s Guide St a t i s t i c s 19-1 This chapter explains the Advanced Management Statistics screens. 19.1 S tatistics Overview The web configurator provides statistics screens to allo w you to see how much traffic the IES-1000 is handling and how it is handling it.
IES-1000 User ’s Guide 19-2 S tatistics Table 19-1 Statistics LABEL DESCRIPTION DSL Driver | Modem Code Conversion This field displays the version of DSL dri ver and modem code. Hardware Monitor Click this button to display temperature statistics. Port Statistics Click this button to display statis tics for the port s.
IES-1000 User ’s Guide St a t i s t i c s 19-3 Table 19-2 Hardware Monitor LABEL DESCRIPTION Status This field displays Norma l for temperatures bel ow the threshold and Error for those above. Poll Interval(s) The text box displays how often (in seconds ) this scre en refreshes.
IES-1000 User ’s Guide 19-4 S tatistics Table 19-3 Port Statistics LABEL DESCRIPTION State This field shows wheth er a port is turned on ( enable ) or off ( disable ). TxPkts This field shows the n umber of frames tran smitted by this port since the netwo rk module last restarted or the statistics were last manually cle ared via command.
IES-1000 User ’s Guide St a t i s t i c s 19-5 Table 19-4 Channel Statistics LABEL DESCRIPTION System Uptime This field shows how long the system ha s been ru nning since the last time it was started. Port This refers to the DSL port number. VPI This field displays the ch annel’s Virtual Path Identifier (VPI).
IES-1000 User ’s Guide 19-6 S tatistics Figure 19-5 VLAN Status The following table describes this screen. Table 19-5 VLAN Status LABEL DESCRIPTION Index This is the VLAN index number. VID This is the VLAN ID number config ured in the Edit Static VLAN page.
IES-1000 User ’s Guide Diagnostic 20-1 This chapter explains the Advanced Management Diagnostic screens. 20.1 Diagnostic Overview The IES-1000 provides diagnostic screens to aid in troubleshooti ng. 20.2 Diagnostic Screen Click Diagnostic in the navigation panel to open the Diagnostic screen.
IES-1000 User ’s Guide 20-2 Diagnostics Table 20-1 Diagnostic LABEL DESCRIPTION Reset Syst em Click this button to restart the IES-1000. A warning dialog box displays asking if you're sure you want to restart the system. Click OK to proceed. Clear System Log Click this button to clear the log of events in the multi-line text box.
IES-1000 User ’s Guide Diagnostic 20-3 Table 20-3 Log Messages LOG MESSAGE TYPE DESCRIPTION ADSL <port> Link Down(SN=<seq no>) WARN An ADSL port lost its connection.
IES-1000 User ’s Guide 20-4 Diagnostics Table 20-3 Log Messages LOG MESSAGE TYPE DESCRIPTION GSHDSL <port> Link Info: NM=<noise margin> ATT=<loop attenuation> INFO This log displays information about a G.SHDSL p ort’s connection.
IES-1000 User ’s Guide Diagnostic 20-5 Table 20-3 Log Messages LOG MESSAGE TYPE DESCRIPTION THERMO RELEASE OVER RANGE: dev:<device id> value:<temp> WARN The temperature detected in the netwo rk module has come back to normal.
IES-1000 User ’s Guide 20-6 Diagnostics Table 20-4 DSL Line Diagnostic LABEL DESCRIPTION Port This refers to the DSL port number. Select a port upon which you want to perform a loopba ck test. Local Loopback Click this to perform a local loopback test on the specified DSL po rt.
IES-1000 User ’s Guide Diagnostic 20-7 Figure 20-4 Logout.
.
IES-1000 User ’s Guide T roubleshooting 21-1 This chapter covers potential problem s and possible remedies. After each problem description, some steps are provided to help you to diagnose and t o solve the problem. 21.1 DSL LED(s) A DSL LED is not on.
IES-1000 User ’s Guide 21-2 T roubleshooting 21.3 DSL LED(s) T urn On and Off A DSL LED turns on and off intermittently. Table 21-3 Troubleshooting a Non-Constant DSL LED STEPS CORRECTIVE ACTION 1 Check the IES-1000’s diagnostic scre en. 2 Connect a DSL modem directly to the DSL port of the IES-1000 using a different telephone wire.
IES-1000 User ’s Guide T roubleshooting 21-3 21.8 Local Server The computer behind a DSL modem or router cannot access a local server connected to the IES-1000. Table 21-7 Troubleshooting a Local Server STEPS CORRECTIVE ACTION 1 Refer to section 21.
Commands V Part V: Commands This part gives informati on on commands for the IES-1000.
.
IES-1000 User ’s Guide Commands Introduction 22-1 This section introduces the command line interface and lists the available commands. 22.1 Command Line Interface Overview In addition to the web configurator, you can use commands to configure the IES-1000.
IES-1000 User ’s Guide 22-2 Commands Introduction [on|off] means that you can use either on or off . 5. “Command” refers to a command used in the command line interface (CI co mmand). Using commands not documented in this User’s Guide can damage the unit and possibly render it unusable.
IES-1000 User ’s Guide Commands Introduction 22-3 Table 22-1 Commands MODULE COMMAND DESC RIPTION bridge config save Saves the bridge’s run time configuration to nonvolatile memory. print Shows the bridge’s run time configuration. reset Reloads the bridge’s run ti me configuration from nonvolatile memory.
IES-1000 User ’s Guide 22-4 Commands Introduction Table 22-1 Commands MODULE COMMAND DESC RIPTION enable [1 | 2] Turns on IGMP snooping. 1 sets unknown-discard mode, 2 sets unknown-flood mode. disable Turns off IGMP snooping. timeout [<seconds>] Sets how long the IES-1000 retains entries in the multicast filtering database.
IES-1000 User ’s Guide Commands Introduction 22-5 Table 22-1 Commands MODULE COMMAND DESCRIPTION <n> Shows buffer <n> in the current buffer pool. steal <num> Steals <num> buffers from the current buffer pool. version Displays version information for the buffer driver.
IES-1000 User ’s Guide 22-6 Commands Introduction Table 22-1 Commands MODULE COMMAND DESCRIPTION read <addr> Reads the MII register of the device with the selected PHY address. write <addr> <data> Writes data to the MII register of the device with selected the PHY address.
IES-1000 User ’s Guide Commands Introduction 22-7 Table 22-1 Commands MODULE COMMAND DESCRIPTION <process> Shows the controlled resources in the specified process. <process> <resource> Shows the value of the specified resource in a process.
IES-1000 User ’s Guide 22-8 Commands Introduction Table 22-1 Commands MODULE COMMAND DESCRIPTION disable <port> Disables 802.1X security on the specified po rt. control <port> <auto|auth| unauth> Sets how the specified port shoul d be authenticated.
IES-1000 User ’s Guide Commands Introduction 22-9 Table 22-1 Commands MODULE COMMAND DESCRIPTION fsck Does a file system check in the current partition. <partition> Does a file system che ck in the specified partition. format Formats the current partition.
IES-1000 User ’s Guide 22-10 Commands Introduction Table 22-1 Commands MODULE COMMAND DESCRIPTION version Shows the version information of file system. adsl The adsl commands apply to the AAM module. config save Saves configuration of the ADSL module to nonvolatile memory.
IES-1000 User ’s Guide Commands Introduction 22-1 1 Table 22-1 Commands MODULE COMMAND DESCRIPTION pvcs <muxMode> <txvpi> <txvci> [<rxvpi> <rxvci>] Sets the PVC configuration to all ADSL ports.
IES-1000 User ’s Guide 22-12 Commands Introduction Table 22-1 Commands MODULE COMMAND DESCRIPTION loopback <portNo> local | f5 Does a local/OAM F5 loopback test on the specified GSHDSL port. stat ch <port> <vpi> <vci> Shows the statistics of the specified PVC channel.
IES-1000 User ’s Guide Commands Introduction 22-13 Table 22-1 Commands MODULE COMMAND DESCRIPTION bondc <bond name> <port list> or bondc <mode> <bond name> <group list> Bonds the specified member list an d sets them to STU-C mode.
IES-1000 User ’s Guide 22-14 Commands Introduction Table 22-1 Commands MODULE COMMAND DESCRIPTION chs [<start port> [<stop port>]] Shows the contents of all PVC channels in all ports o r in the specified ports. vcp <profile name> Shows the contents of the specific VC profile.
IES-1000 User ’s Guide Commands Introduction 22-15 Table 22-1 Commands MODULE COMMAND DESCRIPTION ip arp add <if> <ip> <mac> Adds ARP record <ip> <mac> to interface <if>. delete <if> <ip> Deletes ARP record <ip> from interface <if>.
IES-1000 User ’s Guide 22-16 Commands Introduction Table 22-1 Commands MODULE COMMAND DESCRIPTION delete <netName> Deletes a subnet. flush Removes all sub nets. version Shows the version information for the IP module. isfs trace Shows the ISFS trace level.
IES-1000 User ’s Guide Commands Introduction 22-17 Table 22-1 Commands MODULE COMMAND DESCRIPTION facility <facility> Sets the syslog facility. server <ip> Sets the syslog server IP. secured host Shows the secured host. enable | disable Enables or disables che cking for the secured host .
IES-1000 User ’s Guide 22-18 Commands Introduction Table 22-1 Commands MODULE COMMAND DESCRIPTION list Shows the VLAN’s current status periodically. stop Stops showing the VLAN’s current status periodically. pvid Lists the default port VLAN ID for all ports.
IES-1000 User ’s Guide System Commands 23-1 Chapter 23 System Commands This chapter describes the IES-1000’ s system-related commands. 23.1 System Commands Overview Use the commands described in this chapter to configure system functions on the IES-1000.
IES-1000 User ’s Guide 23-2 System Commands This command changes the management password. The management password is used for authentication at console or Telnet login. This command is only allowed for local console management sessions. The management password must be from 1 to 8 characters long and any ch aracter is accepted.
IES-1000 User ’s Guide System Commands 23-3 192.168.1.1 sys> set contact [<name>] This command allows you to set the name of the contact person for your IES-1000. The previous setting will be cleared if the command is entered with the name omitted.
IES-1000 User ’s Guide 23-4 System Commands where <chassis number>= The number for this IES-1000 chassis (1 to 64). This command sets a number to identify this IES-1000 in a network. This is an op tional parameter to help network administrators keep track of multiple IES- 1000s.
IES-1000 User ’s Guide System Commands 23-5 23.5 UNIX Syslog Commands Use UNIX syslog commands to send logs to your UNIX server. If the DSL link is on or goes down, the IES-1000 will send a log to your UNIX server. The table, shown next, indicates what is logged in each case.
IES-1000 User ’s Guide 23-6 System Commands This command sets the UNIX server IP address. If <server IP>=0.0.0.0 (default), then logs will be dropped (not be sent). 23.6 System Error Log Commands The system error log will record error events locally to the IES-1000 memory.
IES-1000 User ’s Guide ADSL Commands 24-1 The ADSL (Asymmetrical Digital Subscriber Line) subsystem allows yo u to configure and monitor the ADSL ports on the AAM1008 network module. 24.1 ADSL Overview See the web configurator chapter on ADSL for background inform ation about ADSL.
IES-1000 User ’s Guide 24-2 ADSL Commands The config save command saves the ADSL configuration into nonvolatile memory. 24.3.2 Disable Port Command Syntax: 192.168.1.1 adsl> disable port <port number> where <port number> = port number, from 1 to 8.
IES-1000 User ’s Guide ADSL Commands 24-3 24.3.5 Enable Ports Command Syntax: 192.168.1.1 adsl> enable ports The enable ports command forcibly enables all ADSL ports. The factory default of all ports is disabled. A port must be enabled before data transmission can occur.
IES-1000 User ’s Guide 24-4 ADSL Commands An example is shown next. Figure 24-1 Linedata Command Example 24.3.7 Lineinfo Command Syntax: 192.168.1.1 adsl> lineinfo <port number> where <port number> = A port number, from 1 to 8. The lineinfo command shows the line operating values of an ADSL port.
IES-1000 User ’s Guide ADSL Commands 24-5 The results contain the operating modes, interleave delay, parity byte assignment and parity bytes per codeword, symbols per codeword and interleave depth. Information ob tained prior to training to steady state transition will not be valid or will be old inform ation.
IES-1000 User ’s Guide 24-6 ADSL Commands Down/up stream Depth value This is the current downstream or upstream, interle aved codeword depth value. The larger the number, the more interleave blocks data is distribu ted across and the stronger the protection against errors (and the lower the performa nce is).
IES-1000 User ’s Guide ADSL Commands 24-7 Downstream (ds) refers to data from the ATU-C and upstrea m (us) refers to data from the ATU-R. “I” stands for interleaved and “ni” stands for non-interleaved (fast mode). A block is a set of consecutive bits associated with the path; each bit belongs to one and only one block.
IES-1000 User ’s Guide 24-8 ADSL Commands An example is shown next. Figure 24-4 Linerate Command Example These results contain the current downstream and upstream operating values (SHOWTIME) for the requested line, the latest available downstream and upstream margins, channel attenuation and the ma ximum attainable rate.
IES-1000 User ’s Guide ADSL Commands 24-9 24.3.12 List Ports Command Syntax: 192.168.1.1 adsl> list ports The list ports command shows the configured maximum rates, modes and states of all ADSL ports. 24.3.13 Set Profile Command Syntax: 192.168.1.
IES-1000 User ’s Guide 24-10 ADSL Commands The profile is a table that contains information on ADSL line configuration. Each entry in this table reflects a parameter defined by a manager, which can be used to configure the ADSL line. Note that the default value will be used fo r any of the above fields that are omitted.
IES-1000 User ’s Guide ADSL Commands 24-1 1 24.3.15 List Profiles Command Syntax: 192.168.1.1 adsl> list profiles The list profiles command displays all of the ADSL ports and that profile is assigned to each one.
IES-1000 User ’s Guide 24-12 ADSL Commands Figure 24-6 Show Profile Command Example 24.3.17 Show Profiles Command Syntax: 192.168.1.1 adsl> show profiles The show profiles command displays the settings of all the ADSL profiles. 24.3.18 Set Port Command Syntax: 192.
IES-1000 User ’s Guide ADSL Commands 24-13 The mode parameter specifies the standard that this po r t is allowed. When set to auto, the AAM1008 follows whatever mode is set on the other end of the line. An nex A refers to ADSL over PO TS and Annex B refers to ADSL over ISDN.
IES-1000 User ’s Guide 24-14 ADSL Commands where <port number> = A port number, from 1 to 8. The show port command shows the line status (up or down) , the actual upstream/downstream rates and mode of an individual ADSL port. 24.3.21 Show Ports Command Syntax: 192.
IES-1000 User ’s Guide ADSL Commands 24-15 24.3.23 Set PVCs Command Syntax: 192.168.1.1 adsl> set pvcs <multiplexing mode> <tx vpi> <tx vci> [<rx vpi> <rx vci>] wher.
.
IES-1000 User ’s Guide G .SHDSL Commands 25-1 The G.SHDSL (G.991.2 Single-pair High-speed Digital Subscriber Line) subsystem allows you to configure and monitor the G.SHDSL ports on the SAM1008 network module. 25.1 G . SHDSL Overview Refer to the web configurator chapter on G.
IES-1000 User ’s Guide 25-2 G .SHDSL Commands 192.168.1.1 gshdsl> config save This command saves the G.SHDSL configuration into non volatile memory. You must use this command to save any configurations that you make, otherwise the IES-1000 will return to its de fault settings when it is restarted.
IES-1000 User ’s Guide G .SHDSL Commands 25-3 25.3.5 Enable Ports Command Syntax: 192.168.1.1 gshdsl> enable ports This command forcibly enables all G.SHDSL ports. 25.3.6 Lineinfo Command Syntax: 192.168.1.1 gshdsl> lineinfo <port #> where <port #> = A port number, from 1 to 8 This command shows the line operating values of a G.
IES-1000 User ’s Guide 25-4 G .SHDSL Commands where <Port> = The port number on the SAM1008. <Sp> = The line rate. If Sp=0 , then the connection is down. <NM> = Noise Margin. The noise margin in decibels. <ATTEN> = Attenuation.
IES-1000 User ’s Guide G .SHDSL Commands 25-5 Mode = This field displays which port bonding or n-wire mode the port is set to use. “Normal” displays when the port is not p art of an n-wire group. “2-wire” displays when the port is part of a port bonding group (but not part of an n- wire group).
IES-1000 User ’s Guide 25-6 G .SHDSL Commands <Cmin> = The minimum transmission rate in Kbps. This setting is optional. 192 Kbps is the default if you do not configure a value for this parameter. Setting Cmax and Cmin to the same rate fixes the rate for that port.
IES-1000 User ’s Guide G .SHDSL Commands 25-7 An example is shown next. This display shows that there are two profiles (DEFVAL and gold) and that p ort 3 belongs to the gold profile while ports 1, 2, 4 , 5, 6, 7 and 8 belong to the DEFVAL profile. Figure 25-2 List Profiles Command Example 25.
IES-1000 User ’s Guide 25-8 G .SHDSL Commands 192.168.1.1 gshdsl> show profiles The show profiles command displays the settings of all the G.SHDSL profiles. 25.3.15 Set Port Command Syntax: 192.168.1.1 gshdsl> set port <port #> <profile name> where <port #> = The number of the port to which you want to assign a profile.
IES-1000 User ’s Guide G .SHDSL Commands 25-9 networks. The <rx vpi> and <rx vci> settings will be equal to those of <tx vpi> and <tx vci> if the rx settings are not configured. The set pvc command allows the configuration of a PVC (p ermanent virtual circuit) for an individual G.
IES-1000 User ’s Guide 25-10 G .SHDSL Commands 25.3.21 Display All G .SHDSL Line Information Syntax: 192.168.1.1 gshdsl> monitor [<start port> [<stop port>]] where <start port> = The first port number in a range of ports for which you want to display line information.
IES-1000 User ’s Guide G .SHDSL Commands 25-1 1 Make sure that G.SHDSL ports five through eight are all the same end of their connections (all STU-C or all STU- R). G.SHDSL ports one through four do not need to be set to be the same end of the connection as G.
IES-1000 User ’s Guide 25-12 G .SHDSL Commands Make sure that G.SHDSL ports five through eight are all the same end of their connections (all STU-C or all STU- R). G.SHDSL ports one through four do not need to be set to be the same end of the connection as G.
IES-1000 User ’s Guide G .SHDSL Commands 25-13 Make sure that G.SHDSL ports five through eight are all the same end of their connections (all STU-C or all STU- R). G.SHDSL ports one through four do not need to be set to be the same end of the connection as G.
IES-1000 User ’s Guide 25-14 G .SHDSL Commands G.SHDSL ports one through four do not need to be set to be the same end of the connection as G.SHDSL ports five through eight. For exam ple, G.SHDSL ports one th rough four could be set t o be STU-C while G.
IES-1000 User ’s Guide G .SHDSL Commands 25-15 192.168.1.1 gshdsl> delete nwire <group name> where <group name> = The name of the n-wire group.
IES-1000 User ’s Guide 25-16 G .SHDSL Commands 25.3.31 List Bonded Members Command Syntax: 192.168.1.1 gshdsl> list bond The list bond command displays all of the bonded members.
IES-1000 User ’s Guide Virtual Channel Management 26-1 This chapter shows you how to use commands to configure virtual channels. 26.1 About V irtual Channels See the web configurator chapter on virtual channel mana gement for background inf ormation on virtual channels.
IES-1000 User ’s Guide 26-2 Virtual Channel Management <scr/mcr> = The Sustained Cell Rate (scr) sets the av erage cell rate (long-term) that can be transmitted. SCR applies with the rt-vbr and nrt-vbr traffic classes. Min imum C ell R ate (mc r) is t he mi nimum rate at which the sender can send cells.
IES-1000 User ’s Guide Virtual Channel Management 26-3 26.2.3 Delete VCPs Command Syntax: 192.168.1.1 adsl> delete vcps The delete vcps command deletes all of the virtual channel profiles, except the DEFVAL profile. You cannot delete a virtual channel profile that is assigned to any of the network m odule’s DSL channels.
IES-1000 User ’s Guide 26-4 Virtual Channel Management 26.3 PVC Channels Channels (also called Permanent Virtual Circuits or PVCs) let you set priorities for different services or subscribers. You can define up to eight channels on each DSL port and use the m for different services or levels of service.
IES-1000 User ’s Guide Virtual Channel Management 26-5 The delete ch command deletes the specified PVC channel. The following example deletes the PVC channe l for port 8 that uses VPI 0 and VCI 33. 192.168.1.1 adsl> delete ch 8 0 33 26.3.3 Delete Channels Command Syntax: 192.
IES-1000 User ’s Guide 26-6 Virtual Channel Management 26.3.5 Show Channels Command Syntax: 192.168.1.1 adsl> show chs [<start port> [<stop port>]] where <start port> = The first port number in a range of ports for which you want to display line information.
IES-1000 User ’s Guide Virtual Channel Management 26-7 where <start port> = The first port number in a range of ports for which you want to display line information. 1 is used if you leave this blank. <stop port> = The last port number in a range of ports for which you want to display line information.
IES-1000 User ’s Guide 26-8 Virtual Channel Management 192.168.1.1 adsl> stat ch <port> <vpi> <vci> where <port> = A port number (1 to 8) or (*) means all 8 ports. <vpi> = The VPI setting (0 to 255). <vci> = The VCI setting (32 to 65535 if vpi = 0) or (1 to 65535 if the vpi d oes not = 0).
IES-1000 User ’s Guide Virtual Channel Management 26-9 Figure 26-6 Channel Statistics Command Example 26.3.12 Clear Channel Command Syntax: 192.168.1.1 adsl> clear ch <port> <vpi> <vci> where <port> = A port number (1 to 8) or (*) means all 8 ports.
.
IES-1000 User ’s Guide 10/100M Fast Ethernet Port Commands 27-1 The Ethernet subsystem allows you to configure and monitor the 10/100M fast Ethernet port. 27.1 10/100M Fast Ethernet Overview Refer to the web configurator chapter on the ADSL m odule ports for backgrou nd information on the 10/100M auto-sensing Ethernet ports.
IES-1000 User ’s Guide 27-2 10/100M Fast Ethernet Port Commands <speed> = 10 or 100 This command sets the connection speed used when auto-negotiation is turned off. 10 stands for 10Mbps and 100 stands for 100Mbps. 27.2.4 S tatus Command Syntax: 192.
IES-1000 User ’s Guide Bridge Commands 28-1 This chapter discusses the bridge subsystem . It allows you to configure and monitor the bridging, configure MAC filters, port-based VLANs (port filter) and tagged frame functions of t he IES-1000.
IES-1000 User ’s Guide 28-2 Bridge Commands 192.168.1.1 bridge> status This command displays the bridge manageme nt statistics. 28.4 MAC Filter Commands Use MAC filter commands to filter incoming frames based on MAC (Media Access Control) address(es) that you specify.
IES-1000 User ’s Guide Bridge Commands 28-3 <port> = A bridge port number. <mac> = The source MAC address in "00:a0:c5:12:34:56" format. This command adds a source MAC address fixed on a speci fied port. You may add up to five MAC addresses.
IES-1000 User ’s Guide 28-4 Bridge Commands where ID = The location of the entry in the multicast filtering database. VID = The VLAN ID of the entry in the multicast filtering database. GDA = Group Destination Address. The IP address of a multicast group destination.
IES-1000 User ’s Guide Bridge Commands 28-5 28.5.6 Ethertype Command Syntax: 192.168.1.1 bridge> ethertype [<port> <any|ip|pppoe>] where <port> = A bridge port number. any = The filter allows all packet types to be forwarded to and from the specified port.
IES-1000 User ’s Guide 28-6 Bridge Commands An example with an altered configuration is shown next. 192.168.1.1 > bridge 192.168.1.1 bridge> portfilter 2 1 3 192.168.1.1 bridge> portfilter 3 1 2 This example sets the allowed outgoing bridge ports of por t 2 (DSL port 1) to p ort 1 (Ethernet port) and port 3 (DSL port 2).
IES-1000 User ’s Guide Bridge Commands 28-7 Figure 28-5 Example of Modified Port Filter Port 3 The following figure illustrates that port 1 (the Ethernet port) is linked to ports 2 (DSL port 1) and 3 (DSL port 2). Ports 2 (DSL port1) and 3 (DSL port 2) are also linked to each other.
IES-1000 User ’s Guide 28-8 Bridge Commands <port> = The port number on the network module. Port 0 is t he CPU’s port, port 1 is the Ethernet port and ports 2-9 are the br idge ports on net work module modules. These are logical ports. <vid> = The tag number (or IEEE 802.
IES-1000 User ’s Guide DHCP Relay Commands 29-1 This chapter describes how to use the DHCP Relay commands. 29.1 DHCP Relay Overview Refer to the web configurator part for background inf ormation on DHCP. 29.2 DHCP Relay Commands Use these commands to configure the DHCP relay feature.
IES-1000 User ’s Guide 29-2 DHCP Relay Commands The delete command removes the specified DHCP server or all servers fro m the list of servers to which the IES- 1000 relays client TCP/IP configuration requests. 29.2.4 Enable Command Syntax: 192.168.1.
IES-1000 User ’s Guide DHCP Relay Commands 29-3 29.2.8 S tatus Command Syntax: 192.168.1.1 dhcprelay> status The status command displays whether or not the DHCP relay feature is activated. 29.2.9 T race Command Syntax: 192.168.1.1 dhcprelay> trace The trace command activates trace option(s).
IES-1000 User ’s Guide 29-4 DHCP Relay Commands 192.168.1.1 dhcprelay> relayinfo disable The relayinfo disable command turns off the DHCP relay agen t information (Option 82) feature.
IES-1000 User ’s Guide IEEE 802.1X Commands 30-1 This chapter describes how to use the dot1x commands. 30.1 IEEE 802.1X Overview The IES-1000 supports IEEE 802.1X port-b ased authentication (refer to the web configurator part for background information).
IES-1000 User ’s Guide 30-2 IEEE 802.1X Commands where [level] = Use 1 to turn on the packet debug level. This has the IES-1000 display the contents of EAPOL (Extensible Authentication Protocol Over LAN) frames. This can help you determine whether or not the subscriber is sending IEEE 802.
IES-1000 User ’s Guide IEEE 802.1X Commands 30-3 30.2.8 Port Re-authentication Command Syntax: 192.168.1.1 dot1x> port reauth <port> <on|off> where <port> = A port number (1 to 8).
IES-1000 User ’s Guide 30-4 IEEE 802.1X Commands <addr> = The IP address of the external RADIUS server. This command sets the external RADIUS server IP address. 30.2.12 RADIUS Port Command Syntax: 192.168.1.1 dot1x> radius port <portnum> where <portnum> = The UDP port number of the external RADIUS server.
IES-1000 User ’s Guide IEEE 802.1Q T agged VLAN Commands 31-1 This chapter generally describes the IEEE 802.1Q Tagged VLAN and associated CI Commands. 31.1 IEEE 802.1Q T agged VLAN Introduction The IEEE 802.1Q Tagged VLAN allows your network module to deliver tagged/untagged fra mes to and from its ports.
IES-1000 User ’s Guide 31-2 IEEE 802.1QT agged VLAN Commands Example: 1. 192.168.1.1> vlan1q 2. 192.168.1.1 vlan1q> svlan setentry 11 2 fixed untag 3. 192.168.1.1 vlan1q> svlan setentry 11 1 fixed tag 4. 192.168.1.1 vlan1q> pvid 2 11 5. 192.
IES-1000 User ’s Guide IEEE 802.1Q T agged VLAN Commands 31-3 2. 192.168.1.1 vlan1q> vlan enable 31.3 IEEE 802.1Q T agged VLAN Commands Bridge port 1 stands for the Ethernet port, bridge port 2 stands for DSL port 1, bridge port 3 stands for DSL port 2, and so on.
IES-1000 User ’s Guide 31-4 IEEE 802.1QT agged VLAN Commands This command sets the VLAN ID to a specific port in the PVID table. To display the PVID table simply enter this command without parameters, as shown next. Figure 31-1 Example: PVID Command Display Make sure you set all bonded ports to have the same PVID.
IES-1000 User ’s Guide IEEE 802.1Q T agged VLAN Commands 31-5 This command displays the static VLAN registration tabl e. The following figure is an example of what is displayed when you use this command.
IES-1000 User ’s Guide 31-6 IEEE 802.1QT agged VLAN Commands Modify a S tatic VLAN T able Example The following is an example of how to modify a static VLAN table. 1. 192.168.1.1 vlan1q> svlan setentry 3 3 fixed untag 2. 192.168.1.1 vlan1q> svlan setentry 2 2 fixed untag 3.
IES-1000 User ’s Guide IEEE 802.1Q T agged VLAN Commands 31-7 Figure 31-4 SVLAN Example An untagged frame comes in from the LAN. The switch checks the PVID table and assigns a temporary VID of 1. The switch ignores port# 1 (the LAN port where the frame came in), because the switch does not send a frame to the port that it came in through.
IES-1000 User ’s Guide 31-8 IEEE 802.1QT agged VLAN Commands 31.3.7 SVLAN Getentry Command Syntax: 192.168.1.1 vlan1q> svlan getentry <vid> where <vid> = A VLAN ID. Valid parameter range = [1 – 4094]. This command displays an entry with a speci fied VLAN ID in the static VLAN table.
IES-1000 User ’s Guide IEEE 802.1Q T agged VLAN Commands 31-9 Figure 31-6 Example: DVLAN List Command Display In the figure above, “ || ” denotes “filter” and “ >> ” denotes “forward”. 31.3.10 DVLAN Getentry Command Syntax: 192.
IES-1000 User ’s Guide 31-10 IEEE 802.1QT agged VLAN Commands Figure 31-8 Example: VLAN List Command Display In the figure above “ O " denotes “egress port”, “ V ” denotes “tagged” and “ X ” denotes “ untagged”.
IES-1000 User ’s Guide IEEE 802.1p Priority Commands 32-1 This chapter explains IEEE 802.1p Priority CI Commands. 32.1 Introduction IEEE 802.1p Priority CI Commands assign priorit y levels to individual ports.
IES-1000 User ’s Guide 32-2 IEEE 802.1p Priority Commands 32.2.2 Regen Port Command Syntax: 192.168.1.1 vlan1q> regen port [<port #> <user priority> <regenerated priority>] where <port #> = A bridge port number. Valid parameter range = [1 – 9].
IES-1000 User ’s Guide IP Commands 33-1 This chapter shows you how to configure the IP (Internet Protocol) parameters. The IP host implementation in the IES-1000 allows you to manage it ove r the network. More often than not, you have m ore than one IES-1000 for a particular installation.
IES-1000 User ’s Guide 33-2 IP Commands 192.168.1.1> ip 192.168.1.1 ip> enable ether 192.168.1.3 255.255.255.0 192.168.1.1 ip> route delete default 192.
IES-1000 User ’s Guide IP Commands 33-3 <host> = The IP address of the target. <ttl> = Time to Live (optional). This parameter lim its the number of hops (routers) that the echo request can travel before it reaches the target.
IES-1000 User ’s Guide 33-4 IP Commands This command removes all of the subnets. 33.2.8 Route Add Command Syntax: 192.168.1.1 ip> route add <dom name> a.b.c.d <relay> [am:bm:cm:dm [<cost> [<timeout>]]] where <dom name> = The name of the static route.
IES-1000 User ’s Guide IP Commands 33-5 Syntax: 192.168. 1.1 ip> enable [<if> [mtu <size> [<ip> [<ipmask>]]] where <i/f> = The name of an interface (“ether” for this device). [mtu <size>] = Maximum Transmit Unit.
.
IES-1000 User ’s Guide Remote Management 34-1 This chapter shows you how to manage the IES-1000 remotely. 34.1 Remote Management Introduction More often than not, you will have the IES-1000 located re m otely making its remote management features very useful.
IES-1000 User ’s Guide 34-2 Remote Management 34.3.2 SNMP Access Delete Command Syntax: access delete <community> [<IP addr>] This command revokes SNMP access by the specified community (password). If the IP address is specified, access is denied for that manager station only.
IES-1000 User ’s Guide Remote Management 34-3 34.4.2 T rap Delete Command Syntax: trap delete <community> <IP addr> This command deletes a trap destination. The parameters are the sa me as the trap add command. 34.4.3 T rap Flush Command Syntax: trap flush This command deletes all trap destinations.
.
IES-1000 User ’s Guide Configuration Backup/Restore 35-1 This chapter describes the process f or backing up your user settings (configuration) f rom the network module onto your computer and how to restore them to the network module. The network modules use FTP for configuration backup/r estore through their built-in FTP servers.
IES-1000 User ’s Guide 35-2 Configuration Backup/Restore Do not turn off the network module during the restore process, as it may corrupt the firmware and make your network module unusable. Connect to the network module with your favorite FTP c lient.
IES-1000 User ’s Guide Firmware Upload and Recovery 36-1 This chapter describes how to load new firm ware onto your device, or recover firmware that is in t he non-volatile memory. The network modules use FTP to upload firmware and no longer support TFTP uploads.
IES-1000 User ’s Guide 36-2 Firmware Upload and Recovery Do not turn off the network module during the updating process, as it may corrupt the firmware and make your network module unusable. 1. Connect to the network module with your favorite FTP client.
IES-1000 User ’s Guide Firmware Upload and Recovery 36-3 4. Run BootpTftp.exe , to bring up the following window. Click New to create a MAC address entry. Figure 36-1 BOOTP/TFTP Server 5. The Input Box window will pop up as shown next. Type the MAC address of the network module and then click OK .
IES-1000 User ’s Guide 36-4 Firmware Upload and Recovery Figure 36-3 Database Edit Dialog 7. Select Normal Bootp to enable normal BOOTP/TFTP functions. Figure 36-4 Enable BOOTP/TFTP 8. Restart the network module and press any key w ithin three seconds to get the following screen.
IES-1000 User ’s Guide Firmware Upload and Recovery 36-5 10. Enter atnb at the network module boot console. 11. Wait for the firmware upload to finish. 12. Use the following command sequence on the network module to write new firmware to flash memory.
.
IES-1000 User ’s Guide T roubleshooting 37-1 Chapter 37 T roubleshooting This chapter covers potential problem s and possible remedies. After each problem description, some steps are provided to help you to diagnose and t o solve the problem. 37.1 SHDSL or ADSL LED(s) An SHDSL or ADSL LED is not on.
IES-1000 User ’s Guide 37-2 T roubleshooting 37.3 SHDSL or ADSL LED(s) T urn On and Off An SHDSL or ADSL LED turns on and off intermittently. Table 37-3 Troubleshooting a Non-Constant DSL LED STEPS CORRECTIVE ACTIO N 1 Use the lineinfo command with G.
IES-1000 User ’s Guide T roubleshooting 37-3 Table 37-5 Troubleshooting Port Bonding STEPS CORRECTIVE ACTIO N 3 Swap the telephone wiring between the non-t ran smitting port and one of the bonded group’ s transmitting ports. For example, SHDSL ports 1 and 2 are bonde d.
IES-1000 User ’s Guide 37-4 T roubleshooting Table 37-7 Troubleshooting the Password CORRECTIVE ACTIO N Refer to section 36.2 to update your firmware. All settings will retu rn to default values, so any configurations you have made will be lost. 37.
IES-1000 User ’s Guide T roubleshooting 37-5 Table 37-10 Troubleshooting Telnet STEPS CORRECTIVE ACTIO N 3 If you are attempting to telnet from the DSL side of the network module, refer to section 37.2 to make sure that you can transmit data to the network module.
Appendices and Index VI Part VI: Appendices and Index This part gives appendices and an index..
IES-1000 User ’s Guide Safety W arnings A Appendix A Safety W arnings Refer to the Hardware Specifications appendix for the gauge of wire to use for each connection. The length of exposed (bare) IES-1000 power wire should not exc eed 7mm. Do not use this product near water, for example, in a wet basement.
.
IES-1000 User ’s Guide Removing and Installing a Fuse C Appendix B Removing and Inst alling a Fuse This appendix shows you how to remove and install fuses for the AC power IES-1000.
IES-1000 User ’s Guide D Removing and Installing a Fuse Step 4. Gently pull the fuse casing from the IES-1000. The in stalled fuse is located attached to, and on the outside of the fuse housing; the spare fu se is located inside the fuse housing. Diagram 2 Accessing the Spare Fuse Step 5.
IES-1000 User ’s Guide PIN Assignments E Appendix C Pin Assignment s Mini RJ-1 1 4P4C (Console Port) Pin Assignment s Diagram 3 RJ-11 4P4C (Console Port) Pin Assignments RJ-1 1 6P2C (SHDSL Port s on.
IES-1000 User ’s Guide F PIN Assignments Note that a 2, 4 or 6 pin connector can be used with this port provided pins 3 and 4 connect to a SAM1008 SHDSL port.
IES-1000 User ’s Guide Hardware S pecifications G Appendix D Hardware S pecifications Physical Interfaces IES-1000 • Two slots for a total of up to two hot-swappable DSL network m odules • Power.
IES-1000 User ’s Guide H Hardware S pecifications • One AAM1008 = 1.1 kg Wire Gauge S pecifications Chart 1 Wire Gauge Specifications WIRE TYPE REQUIRED AWG NO. (DIAMETER) Telephone Wire 26 or larger DC Power Model IES-1000 Power Wire 16 to 18 American Wire Gauge (AWG) is a measure ment system for wire that sp ecifies its thickness.
IES-1000 User ’s Guide Index I Index # #2 Philips Screwdriver 4-1 1 10 Mbps Ethernet 7-2 10/100M Auto-Sensing Ethernet 11-7 100 Mbps Ethernet 7-2 4 4-wire 12-1 8 802.
IES-1000 User ’s Guide J Index C CBR 13-3, 13-7 CDVT 13-5, 13-7 CE Mark Warning iii Cell Delay Variation Tolerance 13-5 Central Side Port Bonding Command 25-12 Certifications iii Channel Attenuation.
IES-1000 User ’s Guide Index K Disclaimer ii Display All G.SHDSL Line Information 25-10 Downstream 11-7 Downstream (ds) 24-7 Downstream Max Rate: Kbps 11-5 Duplex 8-3 DVLAN Getentry Command 31-9 DVL.
IES-1000 User ’s Guide L Index G.SHDSL Compliance 1-1 G.SHDSL modem 8-2, 8-3 G.SHDSL Module Port Setup 12-3 G.SHDSL Port 8-2 G.SHDSL Ports (SAM1008) 2-1 G.
IES-1000 User ’s Guide Index M LEDs 3-2 Lightening G Limited Warranty iv Line Bit Allocation 24-3 Line Delay Command 24-8 Line Operating Values 24-4, 25-3 Line Performance Counters 24-6, 25-3 Line R.
IES-1000 User ’s Guide N Index Network Modules 1-1 NIC See Network Interface Ca rd Non real-time Variable Bit Rate 13-4, 13-7 NRM 13-4, 13-7 nrt-VBR 13-7 nrt-VBR) 13-4 Number of Resource Manageme nt.
IES-1000 User ’s Guide Index O Rack-Mounted IES-1000 Installation 4-1 RADIUS (Remote Authent ication Dial-In User Service) 10- 17 RADIUS IP Command 30-3 RADIUS Port Command 30-4 RADIUS Secret Comman.
IES-1000 User ’s Guide P Index Set Port Command 24-12, 25-8 Set Ports Command 24-13, 25-8 Set Profile Command 24-9, 25-5 Set PVC Command 24-14, 25-8 Set PVCs Command 24-15, 25-9 Set Remote Side N-wi.
IES-1000 User ’s Guide Index Q Syslog Server Command 23-5 System Commands 23-1 System Error Log Commands 23-6 System Error Logging 1-3 System Name 10-1 T Table of Contents vi Tagged Ethernet Frames .
IES-1000 User ’s Guide R Index Tags 31-1 Unware Device s 31-1 VLAN Acceptable Frame Type 11-9, 11-11, 12-9 VLAN Disable Command 31-3 VLAN Enable Command 31-3 VLAN List Command 31-9 VPI 13-10 VT100 3.
An important point after buying a device ZyXEL Communications IES-1000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ZyXEL Communications IES-1000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ZyXEL Communications IES-1000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ZyXEL Communications IES-1000 you will learn all the available features of the product, as well as information on its operation. The information that you get ZyXEL Communications IES-1000 will certainly help you make a decision on the purchase.
If you already are a holder of ZyXEL Communications IES-1000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ZyXEL Communications IES-1000.
However, one of the most important roles played by the user manual is to help in solving problems with ZyXEL Communications IES-1000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ZyXEL Communications IES-1000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
