Instruction/ maintenance manual of the product bps-120 ZyXEL Communications
Go to page of 20
BPS-120 Stand-Alone Backup Power System User’s Guide V ersion 1.0 October 2004.
BPS-120 User’s Guide 2 1. Copyright Copyright © 2004 by Zy XEL Communications Corporation. The contents of this publ ication m ay not be reprod uced in any part or as a w hole, transcribed, stored .
BPS-120 User’s Guide 3 radio comm unications. Operation of this equipm ent in a residentia l area is li kely to cause harmful interference in which case the us er w ill be required to correct the interferen ce at his own expense. CE Mark W arning: This is a class A product.
BPS-120 User’s Guide 4 Users should not attempt to mak e such conn ections themselves, but sh ould contact the appropriate electrical inspection authority, or electrician, as appropriate.
BPS-120 User’s Guide 5 5. Customer Support When you contact your cu stomer support representative please have t he following information ready: Please have th e following i nformation re ady when you cont act customer support. • Product model and serial num ber.
BPS-120 User’s Guide 6 SUPPORT E-MAIL TELEPHONE 1 WEB SITE METHOD LOCATION SALES E-MAIL FAX 1 FTP SITE REGULAR MAIL support@zyxel.dk +45 39 55 07 00 www.zyx el.dk DENMARK sales@zyx el.dk +45 39 55 07 07 ZyXEL Communications A/S Columbusvej 5 2860 Soeborg Denmark support@zyxel.
BPS-120 User’s Guide 7 T able of Content s 1 Introducing th e BPS-120 ................................................................................. 9 2 Hardware Inst allati on and Conn ections ....................................................
.
BPS-120 User’s Guide 9 1 Introducing the BPS-120 The BPS-120 is a backup power system to wh i ch you can connect up to s ix of ZyXEL ’s devices that ha ve a 12VDC ext ernal backup p ower supply connector.
BPS-120 User’s Guide 10 Do not block the device’s rear panel or the side panel ventilation holes. Leave space between devices when stacking. 2.1 Desktop Inst allation 1. Set the BPS-120 upside-down on a st urdy level s pace with a 100/240 VAC power outl et nearby.
BPS-120 User’s Guide 11 Figure 2 Attaching the Rack Mounting Brackets 2. After attaching both moun ting brackets, position the BPS-1 20 in the rack by lining up the ho les in the brackets with the ap propriate holes on the rack. Secure the BPS-120 to the rack with the rack’s mounting screws.
BPS-120 User’s Guide 12 2.3 Att aching Power Cables and Connector Definition T h e BPS-1 2 0 i n clu d es p o w e r c o nnections for up to s i x (6) e x ternal devices. T h e rear connector pin-out diagram and power signal descripti ons are show n in the following Figure 5 , and Table 1 for OUTPUTs (1-6).
BPS-120 User’s Guide 13 Figure 5 BPS-120 OUTPUT Port Connector Pin Diagram, and Cable.
BPS-120 User’s Guide 14 Table 1 BPS-120 OUTPUT Port Connector(s) (1-6) Pin Definition PIN NUMBER DESIGN ATION 1 GND 2 N/A 3 12V 4 12V 5 12V 6 12V 7 GND 8 GND 9 N/A 10 BPS present 11 BPS Status0 12 BPS Status1 13 Power good 14 GND 2.4 Front Panel and LED Displays The BPS-120 defaults to STANDBY mode w hen the BPS-12 0 is switche d on.
BPS-120 User’s Guide 15 should be lit) when connecting external devices, then toggle th e STANDBY/ACTIVE mode switc h (shown i n Figure 6 ) to active m ode to update OUTPUT 1-6 priority and sense new power readin gs at the output ports . The ACTIVE LED should light.
BPS-120 User’s Guide 16 Table 2 BPS-120 System States a nd I nternal Sy stem Indicators BPS-120 STATE PWR TEMP F AN FAULT On: The BPS-120 has detected an internal system problem or external power fault.
BPS-120 User’s Guide 17 Table 4 BPS-120 Front Panel DC Ou tp ut LEDs State Definitions PORT LED INDICATIONS COLOR DC OUTPUT LED STATUS DESCRIPTION NO CONNECTION Green Off No external device is connected to OUTPUT 1-6. NO CONNECTION Amber Off No external device is connected to OUTPUT 1-6.
BPS-120 User’s Guide 18 Table 4 BPS-120 Front Panel DC Ou tp ut LEDs State Definitions PORT LED INDICATIONS COLOR DC OUTPUT LED STATUS DESCRIPTION DEVICE FAULT Amber Off The BPS-120 has detected an external or internal fault. See Table 5 . DEVICE FAULT Red On T he BPS-120 has detected an external or internal fault.
BPS-120 User’s Guide 19 Table 5 BPS-120 Troubleshooting Tips PROBLEM CONDITION CORRECTIVE ACTION The PWR LED is red. DC output power is unavailable or not operating properly. The interna l power supply is defective or the BPS-120 has detected an overcurrent.
BPS-120 User’s Guide 20 Table 6 Technical Specifications for the BPS-120 Safety UL 60950-1 CSA 60950-1 EN60950-1 IEC-60950-1 EMC FCC Part15 (Class A) CE EMC (Class A).
An important point after buying a device ZyXEL Communications bps-120 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ZyXEL Communications bps-120 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ZyXEL Communications bps-120 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ZyXEL Communications bps-120 you will learn all the available features of the product, as well as information on its operation. The information that you get ZyXEL Communications bps-120 will certainly help you make a decision on the purchase.
If you already are a holder of ZyXEL Communications bps-120, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ZyXEL Communications bps-120.
However, one of the most important roles played by the user manual is to help in solving problems with ZyXEL Communications bps-120. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ZyXEL Communications bps-120 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
