Instruction/ maintenance manual of the product 7072 Zoom
Go to page of 40
Operation Manual CONTENTS USAGE AND SAFETY PRECAUTIONS •••••••••••••••••••••••••••• 2 Introduction •••••••••••••••.
USAGE AND SAFETY PRECAUTIONS USAGE AND SAFETY PRECAUTIONS 2 ZOOM 707II GUITAR In this manual, symbols are used to highlight warnings and cautions for you to read so that accidents can be prevented. The meanings of these symbols are as follows: Please observe the following safety tips and precautions to ensure hazard-free use of the 707II.
3 ZOOM 707II GUITAR ● Versatile effects The Variable Architecture Modeling System(VAMS) adapts the internal configuration of the unit to achieve exactly the desired sound. The wide range of choices includes distortion effects, modulation effects such as chorus and flanger, reverb and delay effects, as well as a booster and cabinet simulator.
POWER A0 [ W ]/[ Q ] foot switches Expression pedal [AUX IN] jack [INPUT] jack [DC 9V] (AC adapter) jack [POWER] switch [OUTPUT] knob Cable hook [OUTPUT/PHONES] jack [DRIVE VARIATION] LEDs [DRIVE VARIATION] key [DRIVE] knob This section identifies the parts of the 707II and describes preparations for use.
POWER A0 Display Module LEDs MODULE [ E ]/[ R ] keys [BANK/PATCH] indicator [STORE/EXECUTE] key [CANCEL/EXIT] key [PLAY] key [PEDAL] (pedal assign) key [PEDAL] (pedal assign) LEDs [EDIT] key Parameter.
Preparations Pr eparations Inserting Batteries and a SmartMedia card 6 ZOOM 707II GUITAR 1. Turn the unit over and open the battery compartment cover. 2. Insert four fresh IEC R6 (size AA) batteries into the battery compartment. The use of alkaline batteries is recommended.
7 ZOOM 707II GUITAR 1. Make sure that the amplifier and the 707II are off. Turn the volume at the amplifier to minimum. 2. To power the unit from the AC adapter, insert the small plug of the adapter cable into the [DC 9V] jack on the 707II. Then plug the adapter into an outlet.
POW PRESET group USER group BANK F PATCH 1 BANK b PATCH 0 PATCH 2 PATCH 3 PATCH 4 PATCH 5 PATCH 6 PATCH 7 PATCH 8 PATCH 9 PATCH 1 BANK A PATCH 0 PATCH 2 PATCH 3 PATCH 4 PATCH 5 PATCH 6 PATCH 7 PATCH 8.
WER A0 While playing your instrument, operate the knobs on the panel. Each knob controls a certain parameter , as indicated below . Selects the distortion type for the DRIVE module. Adjusts the modulation rate of chorus, flanger , and similar effects.
Listening to Patches (Play Mode Operation) Listening to Patches (Play Mode Operation) Panel Display in Play Mode Selecting a Patch 10 ZOOM 707II GUITAR 1. In play mode, press one of the [ W ]/[ Q ] foot switches. Pressing the [ Q ] foot switch moves to the next higher patch, and pressing the [ W ] foot switch moves to the next lower patch.
11 ZOOM 707II GUITAR 1. To set the 707II to the bypass (mute) condition, press and release both [ W ]/[ Q ] foot switches in play mode. When you press and immediately release both foot switches, the 707II goes into bypass mode. While the 707II is in the bypass condition, all effects are off and only the direct sound is output.
Using the Easy Edit Function 12 1. To change the sound of a patch in play mode, operate parameter knobs 1 – 3. The parameters controlled by the knobs are as follows. The actual parameter controlled by parameter knobs 1 – 3 depends on the effect selected for the current effect module.
ZOOM 707II GUITAR 13 1. When wishing to use a SmartMedia card, turn power to the 707II off, insert the SmartMedia card into the card slot, and then turn power on again. (For information on inserting a SmartMedia card, see p. 6.) • Before using a SmartMedia card in the 707II, it must be formatted ( → p.
14 •I f the indication "NO" is followed by a "*", a sample is recorded in that number. • If you select a number in which a sample has already been recorded, the previous sample will be overwritten. Be careful not to overwrite a sample that you wish to keep.
15 9. If necessary, you can adjust the sample playback level with parameter knob 3. When you operate parameter knob 3, the indication "SP LVL" appears on the display. The [BANK/PATCH] indicator shows the input signal level, using a range from 0 – 30.
Using the Rhythm Function 16 ZOOM 707II GUITAR The 707II incorporates 60 rhythm patterns which can be selected for playback. This is convenient for parts practice or a quick jam session. 1. Press the [ R / P ] key in play mode. Rhythm pattern playback starts.
ZOOM 707II GUITAR 17 8BEA T1 8BEA T2 8BEA T3 8BEA TSHUFFLE 16BEA T1 16BEA T2 16BEA T3 16BEA TSHUFFLE 3/4 6/8ROCK 5/4 5/4ROCK ROCK'nROLL1 ROCK'nROLL2 ROCK1 ROCK2 HARDROCK1 HARDROCK2 MET AL1 M.
Changing the Sound of a Patch (Edit Mode) Changing the Sound of a Patch (Edit Mode) Patch Configuration Basic Edit Mode Steps 18 ZOOM 707II GUITAR Within each module, there are several different but related effects which are called effect types. For example, the MODULATION module comprises effect types such as CHORUS, PHASER, and WAH.
19 ZOOM 707II GUITAR Because the ISOLATOR, EQ, and TOTAL modules have many parameters, settings are divided into several pages. To switch the page, press the [EDIT] key while the corresponding module LED is lit. 4. To switch the on/off status of the selected module, press both MODULE [ E ]/[ R ] keys together.
Changing the Sound of a Patch (Edit Mode) 20 ZOOM 707II GUITAR Storing and Swapping Patches This section describes how to store an edited patch in memory, and how to swap patches in the USER group. 1. In play mode or edit mode, press the [STORE/EXECUTE] key.
Other Functions Using the Hold Delay Function 21 1. In play mode, select the patch to use with hold delay. 2. Press the [EDIT] key to activate edit mode, and select "HLDDLY" as effect type for the DLY/REV module. 3. Use parameter knob 1 to set the TIME parameter.
Other Functions 22 ■ If a numeric value is set as TIME parameter Recording starts at the moment you push the [ Q ] foot switch and continues for the duration set with the TIME parameter.
ZOOM 707II GUITAR 23 1. To change the patch call method to preselect, hold down the [ Q ] foot switch while turning power to the 707II on. 2. Select the patch in play mode. When you select a patch in this condition, the display and [BANK/PATCH] indicator show the new patch (flashing), but the sound does not change.
ZOOM 707II GUITAR 24 MODULATION module, the effect type is temporarily switched to P-PIT. ● MOD The effect type currently selected for the MODULATION module is adjusted by the pedal. Which parameter is controlled depends on the effect type. ● GAIN The distortion gain is adjusted by the pedal.
25 For example, when PDLMIN is set to 4 and PDLMAX to 8, the parameter adjustment range will be limited as shown in the illustration below. When PDLMIN is set to 7 and PDLMAX to 2, pushing the pedal decreases the parameter value, and the range is as shown below.
Storing Rhythm Patterns and Samples as Part of a Patch 26 By assigning rhythm patterns to patches, you can have the rhythm change in sync with the patches. 1. In play mode, select the patch to which you want to assign a rhythm pattern, and press the [EDIT] key.
27 8. Press the [ R / P ] key. The rhythm pattern of the patch selected in step 7 starts to play. (If an intro type pattern has been assigned, playback starts when the patch is switched in step 7.) 9. If necessary, use parameter knobs 2 and 3 to adjust the tempo and volume of the pattern.
Using SmartMedia card (Utility Mode) 28 If you want to check out the sample, press the [SAMPLER] key to activate the sampler mode, and press the [ W ] foot switch to play the currently selected sample. 6. Press the [STORE/EXECUTE] key to store the patch.
29 4. Press the [STORE/EXECUTE] key. The setting screen for the function selected in step 3 appears. The subsequent steps depend on the selected function. For details, see the respective sections. Storing a single patch on a SmartMedia card You can store a single patch from the internal memory of the 707II on a SmartMedia card.
30 and the [BANK/PATCH] indicator shows the load source bank (A – F) and patch number (0 – 9). 4. Press the [STORE/EXECUTE] key. The indication "SURE?" appears on the display. 5. To carry out the operation, press the [STORE/EXECUTE] key once more.
31 Deleting a group from a SmartMedia card You can delete any group stored on a SmartMedia card. 1. In utility mode, select "P DEL" and press the [STORE/EXECUTE] key. The indication "GROUP" appears on the display, and the [BANK/PATCH] indicator shows the group number (1 – 5) for deleting.
32 3. To carry out the operation, press the [STORE/EXECUTE] key once more. The formatting process starts. When the process is completed, the unit reverts to play mode. If you press the [CANCEL/EXIT] key instead of the [STORE/EXECUTE] key, the formatting operation is canceled.
ZOOM 707II GUITAR Ef fect T ypes and Parameters 33 Universal type compressor that controls attack rate in two stages. ATTACK(FAST/SLOW) FS, SL Adjusts time interval from signal onset to start of compression. SENS 0 – 10 Adjusts compressor sensitivity.
ZOOM 707II GUITAR Effect Types and Parameters EQ (Equalizer) Module 34 High-gain tube preamp sound Tube stack amp sound for heavy metal Warm and modern tube stack amp sound ZOOM's original 9002 t.
ZOOM 707II GUITAR 35 LOW G -12 – 12 Adjusts boost/cut in low range selected with LOW F. LEVEL 1 – 8 Adjusts signal level after passing equalizer module. Parameter 3 Parameter 2 Effect Types and Parameters ZNR/D GA TE (ZOOM Noise Reduction/D Gate) Module CABINET Module MODULA TION Module This module serves for cutting noise during play pauses.
ZOOM 707II GUITAR 36 COLOR 1 – 4 Selects sound character. Periodically varies the level of the sound. DEPTH 0 – 10 Adjusts modulation intensity. RATE 1 – 30 Adjusts modulation speed. CLIP 0 – 10 Adjusts modulation waveform clip. Larger values result in more intense modulation.
ZOOM 707II GUITAR 37 This effect tracks the picking action and controls filter opening accordingly. POSI AF, bF Selects connection point of MOD module. • AF: After CABINET module • bF : Before DRIVE module TIME 1 – 30 Adjusts filter attack speed.
ZOOM 707II GUITAR 38 FB 0 – 10 Adjusts number of repeat cycles (feedback) for delay sound. MIX 0 – 30 Adjusts delay sound level. This is a combined delay and hall reverb effect. This is a combined delay and room reverb effect. * Parameters for DLYHAL and DLYROM are the same.
ZOOM 707II GUITAR 39 ■ No sound, or very low volume •I s the correct AC adapter connected, and the power switch set to ON? Refer to "Getting Connected" on page 7 and turn the power on.
Patch List ZOOM CORPORATION NOAH Bldg., 2-10-2, Miyanishi-cho, Fuchu-shi, Tokyo 183-0022, Japan PHONE: +81-42-369-7116 FAX: +81-42-369-7115 Web Site: http://www.
An important point after buying a device Zoom 7072 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Zoom 7072 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Zoom 7072 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Zoom 7072 you will learn all the available features of the product, as well as information on its operation. The information that you get Zoom 7072 will certainly help you make a decision on the purchase.
If you already are a holder of Zoom 7072, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Zoom 7072.
However, one of the most important roles played by the user manual is to help in solving problems with Zoom 7072. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Zoom 7072 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
