Instruction/ maintenance manual of the product Cadet 310 Solid Zodiac
Go to page of 10
/ 10 E N G L I S H 1 CAUTION z CAREFULLY READ THIS MANUAL BEFORE OPERATING YOUR BOAT. z THIS OWNER’S MANUAL IS IN TWO VOLUMES THAT MUST BE KEPT TOGETHER. NOTICE: THE OWNER'S MANUAL IS IN TWO VOLUMES: - VOLUME 1 DEALS WITH OPERATING PRECAUTIONS AND SAFETY RECOMMENDATIONS THAT MUST BE OBSERVED.
/ 10 2 ASSEMBLY PROCEDURE We recommend that you follow the specific order of the assembly procedur e. Proceed step by step and refer to the corresponding pages. PROCEDURE PAGE SECTION 1. inventory the elements composing your boat, 2 CHECK ON UNPA CKING and learn how to recognise them I - IV DESCRIPTION 2.
/ 10 E N G L I S H 3 ASSEMBLY Choose a smooth and clean surface IF THE BUOYANCY TUBE WAS STOR ED AT A TEMPERATURE BELOW 0°C / 32°F, LEAVE IT AT 20°C / 68°F FOR 12 HOURS BEFORE UNFOLDING. CADET SOLID : INSTALL THE MARINE PLYWOOD FLOOR: • Sprinkle some starch in the angle (joint of t he buoyancy tubes to the bottom) to facilitate fitting.
/ 10 4 ASSEMBLY fig 1-A 1 2 3 4 5 6 fig 1-B a- angle b- floorboard c- tube d- bottom a b c d fig 2 1 2 3 4 5 6 fig 3 fig 4 7 8 1 2 3 4 5 7 9.
/ 10 E N G L I S H 5 ASSEMBLY CADET ROLL UP 200 - 240: INSTALL THE SLATTED FLOOR: Boat deflated, slide the slats in their pockets starting by the closes t to the transom.
/ 10 6 INFLATION SYSTEM The inflation system is composed of: THE FOOT PUMP a. connecting tip b. hose end piece c. hose base d. outlet for inflation a b c d THE STANDARD VALVES ( 1 ) cap ( 2 ) valve insert ( 3 ) base To activate the standard valv es into INFLATION position: • Free the valve insert from its protection.
/ 10 E N G L I S H 7 INFLATION Activate all valv es into inflation position . Fit the hose to the foot-pump. To inflate your boat properly, the bottom side of the foot-pump must rest on a flat ground .
/ 10 8 PRESSURE The correct pressure for the buoyancy tube and the keel is 240 mb / 3,4 PSI (green area of the pressure indicator). If your boat is not equipped with a ACCESS pressure indicator, we recommend that you purchase one from your Dealer. This will permit a quick and efficient control of the pressure during inflation.
/ 10 E N G L I S H 9 ASSEMBLY OF STANDARD EQUIPMENT TO ASSEMBLE AND INSTALL THE OARS: THE REMOVABLE SEAT (EXCEPT C 200 ROLL UP) Install the seat before the boat is totally inflated.
/ 10 10 DEFLATING / FOLDING THE BOAT 1. Deflate the boat. 2. Replace the valve protections. 3. Remove oars and equipment. 4. Remove the floorboard (For Cadets solid only - for cadets Roll up with a slatted floor, It is not necessary to remove the slats to fold the boat).
An important point after buying a device Zodiac Cadet 310 Solid (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Zodiac Cadet 310 Solid yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Zodiac Cadet 310 Solid - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Zodiac Cadet 310 Solid you will learn all the available features of the product, as well as information on its operation. The information that you get Zodiac Cadet 310 Solid will certainly help you make a decision on the purchase.
If you already are a holder of Zodiac Cadet 310 Solid, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Zodiac Cadet 310 Solid.
However, one of the most important roles played by the user manual is to help in solving problems with Zodiac Cadet 310 Solid. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Zodiac Cadet 310 Solid along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
