Instruction/ maintenance manual of the product rcli-ac charger Zebra Technologies
Go to page of 10
AM16905-001 Rev .A pg. 1 of 10 INST ALLA TION INSTRUCTIONS READ THIS MANUAL CAREFULL Y! F AIL URE TO INST ALL THIS EQUIPMENT PER THESE INSTRUCTIONS WILL VOID THE W ARR ANTY .
pg. 2 of 10 AM16905-001 Rev . A SPECIAL NOTICES The following notices emphasize certain information in the guide. Each serves a special purpose and is displayed in the format shown: Note: Note is used to emphasize any significant information. Caution: Indicates information that, if not followed, can result in damage to software, hardware, or data.
AM16905-001 Rev .A pg. 3 of 10 ELECTRICAL INFORMA TION 100 - 240 V AC, 50-60 Hz CAUTIONS Installation To ensure that the Charger has proper cooling, do not place any padding or cushioning material under the unit or next to the back of the unit.
pg. 4 of 10 AM16905-001 Rev . A QL Series P rinter INTRODUCTION NOTE: Zebra T echnologies Corporation is not liable for personal injur y or damage to any equipment caused by the improper installation of this equipment to any power source.
AM16905-001 Rev .A pg. 5 of 10 REGUL A TORY INFORMA TION Regulatory Markings T ype-approval labels indicate compliance with country regulations. This product carries country-specific labels to indicate compliance.
pg. 6 of 10 AM16905-001 Rev . A INST ALL A TION T ools Required • An electrical drill • 5/32”(4 mm) drill bits (for clearance holes) • T aps- #6-32 (M3) (optional) • Common hand tools Refere.
AM16905-001 Rev .A pg. 7 of 10 NOTE: Locate the Charger and route the cables out of the way of normal use. Refer to Figure 2 for Charger mounting dimensions.
pg. 8 of 10 AM16905-001 Rev . A General Guidelines • Route the Input Power from the general area where the unit(s) will be mounted. • Protect the cables with a snap-in bushing if they must be routed through a wall or sheet-metal enclosures. • Make sure that cable routing does not interfere with other equipment.
AM16905-001 Rev .A pg. 9 of 10 Connect the Printer • Plug the output cable from the Charger to the battery connection on the printer . (Re- fer to the QL Series Users Guide or the or R W 420 Users Guide for more informa- tion.
. AM16905-001 rev . A 3/4 /05 Printed in U.S.A. TECHNICAL SUPPORT U.S. ONL Y Zebra maintains a help line for questions involving installation of the RCLI-AC Chargers. Please have as much information as possible regarding your particular application ready when you call to enable the technical support personnel to help you.
An important point after buying a device Zebra Technologies rcli-ac charger (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Zebra Technologies rcli-ac charger yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Zebra Technologies rcli-ac charger - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Zebra Technologies rcli-ac charger you will learn all the available features of the product, as well as information on its operation. The information that you get Zebra Technologies rcli-ac charger will certainly help you make a decision on the purchase.
If you already are a holder of Zebra Technologies rcli-ac charger, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Zebra Technologies rcli-ac charger.
However, one of the most important roles played by the user manual is to help in solving problems with Zebra Technologies rcli-ac charger. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Zebra Technologies rcli-ac charger along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
