Instruction/ maintenance manual of the product 2722 Zebra Technologies
Go to page of 30
User’s Manual No. 980344-001 Rev. A ©2001 Zebra Technologies Corporation 2722 2742 3742 Desktop Thermal Printer User’s Manual.
COPYRIGHT NOTICE This document contains information proprietary to Zebra Technologies Corporation. This docu - ment and the information contained within is copyrighted by Zebra Technologies Corporation and may not be duplicated in full or in part by any person without written approval from Zebra Technol - ogies Corporation.
TABLE OF CONTENTS Installation and Operation Unpacking Your Printer . . . . . . . . . . . . . . . . . . . . 2 Getting To Know Your Printer . . . . . . . . . . . . . . . . . 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Attach Power .
General Cautions and Warnings This page describes general safety and maintenance warnings and cautions for the printer and are referenced throughout the manual. Warning - Shock Hazard The printer should never be operated in a location where it can get wet.
1 Installation and Operation This section provides information on the instal- lation and operation of the printer. The printer is a low cost, desktop thermal bar code printer. LP models are direct thermal. TLP modes are thermal transfer and direct thermal printers.
Unpacking Your Printer Installation and Operation 2 980344-001 Rev.A For W in B a r C o d e L a b e l P r in t e r s S o ftw a re a n d D o c u m e n ta tio n 105551 -006 © 2001 Zeb ra T echno log ie.
Getting To Know Your Printer 980344-001 Rev.A 3 Installation and Operation.
Installation The following steps will guide you through the installation of the printer, media and software. Step 1 - Attach Power SHOCK HAZARD WARNING See page iv Installation and Operation 4 980344-001 Rev.
Step 2 - Attach Interface Cable 980344-001 Rev.A 5 Installation and Operation Parallel Interface Serial Interface.
Step 3 - Load Media Installation and Operation 6 980344-001 Rev.A Open Cover Open Print Head Open Guides MOVIE MOVIE MOVIE.
Before You Load Media in the Printer You must remove the outside length of media (that is, one, full revolution of labels and any liner). When you remove this part of the media, you remove the oils, dust, and adhesives that contaminate it.
Step 3 - Load Media (cont.) Installation and Operation 8 980344-001 Rev.A 2722 Install Roll Media OUT OUT OUT OUT OUT OUT OUT OUT 2742 / 3742 Install Roll MOVIE.
Step 3 - Load Media (cont.) 980344-001 Rev.A 9 Installation and Operation Thread the Media MOVIE MOVIE Seat Media Roll.
Step 3 - Load Media (cont.) Installation and Operation 10 980344-001 Rev.A Close Guides Close Guides 2742 / 3742 MOVIE.
Step 3 - Load Media (cont.) 980344-001 Rev.A 11 Installation and Operation Close Cover MOVIE MOVIE Close Print Head.
Step 3 - Load Media (cont.) If the indicator fails to light, refer to Appendix A - Trouble Shooting. Run the AutoSense routine. Installation and Operation 12 980344-001 Rev.
Step 4 - AutoSense Step 5 - Install Software Start your computer and follow the installation instructions on the compact disc (CD). 980344-001 Rev.A 13 Installation and Operation O O 2 UKQ1813 4.00 Serial port : 96,N,8,1 Image buffer size:245K Fmem:000,0K,019.
Using Fan-Fold Media Installation and Operation 14 980344-001 Rev.A Place Media In Rear Face Print Surface UP Insert & Load Media.
Label Dispenser Printers with an optional label taken sensor can dispense a single peeled label. Remove the label to automatically print the next label.
Label Dispense Option Installation and Operation 16 980344-001 Rev.A TLP2722 Insert Liner (2742 Shown) Pull Liner Through (2742 Shown).
Label Dispense Option 980344-001 Rev.A 17 Installation and Operation Close Print Head Close Cover TL P 2722 Push to Open Label Taken Sensor Press FEED Button TLP2722 Remove Presented Label.
Thermal Transfer Ribbon Loading This feature is supported on TLP model printers, only. Installation and Operation 18 980344-001 Rev.A Thermal Transfer Print Head Mechanism MOVIE Ribbon Path.
Thermal Transfer Ribbon Loading Open Print Head 980344-001 Rev.A 19 Installation and Operation Load Ribbon Core Load Transfer Ribbon Start Ribbon Open Print Head (Rear View) Pull Ribbon Around Print H.
Installation and Operation 20 980344-001 Rev.A.
Appendix A - Troubleshooting Problem Solution or Reason POWER indicator does not light GREEN when power switch is turned to ON (1) position. 1. Check power connections from A.C. outlet to power supply to printer. POWER indicator lights GREEN, but printer will not print.
Printer Maintenance 22 980344-001 Rev.A Clean the Print Head Don’t Clean Rollers with Cleaning Pen MOVIE.
Printer Configuration Settings The printer has flash (non-volatile) memory to store printer configuration settings. The settings are stored in flash memory and are set by programing, printer drivers or the AutoSense routine. The settings are shown on the Dump mode printout or can be reported back to the host via the serial port.
Serial Interface Communication Configuration The printer’s serial port is configured with the Y command for the printer. The printer supports interface data rates from 1200 to 38,400 baud.
Parallel Interface Cable Wiring The figure below displays the cable wiring required to use the printer's Centronics parallel interface. +5 volts at 300 mA for external device (e.g. PrintServer) 980344-001 Rev.A 25 PRINTER DB -25 Pin No. Centronics Pin No.
26 980344-001 Rev.A.
An important point after buying a device Zebra Technologies 2722 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Zebra Technologies 2722 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Zebra Technologies 2722 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Zebra Technologies 2722 you will learn all the available features of the product, as well as information on its operation. The information that you get Zebra Technologies 2722 will certainly help you make a decision on the purchase.
If you already are a holder of Zebra Technologies 2722, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Zebra Technologies 2722.
However, one of the most important roles played by the user manual is to help in solving problems with Zebra Technologies 2722. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Zebra Technologies 2722 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
