Instruction/ maintenance manual of the product ZI 9224 Zanussi
Go to page of 20
REFRIGERA TOR ZI 9224 2222758-70 INSTRUCTION BOOKLET.
2 These warnings are provided in the interests of your safety . Ensure that you understand them all before installing or using this appliance. Y our safety is of paramount importance. If you are unsure about any of the meanings of these warnings contact the Customer Care Department.
3 Contents Instructions for the User Important Safety Instructions . . . . . . . . . . . . . . . .2 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Before use / Setting the temperature . . . . . . . . . . .4 Fresh food refrigeration .
4 Fresh food refrigeration T o obtain the best performance, do not store warm food or evaporating liquids in the refrigerator; do cover or wrap the food, particularly if it has a strong flavour . Do not cover the shelves with any protective material, such as paper , cardboard or plastic, which may obstruct the air circulation through them.
5 Bottle holder ¥ Place the bottles (with the opening facing front) in the pre-positioned shelf. If the shelf is positioned horizontally , place only closed bottles. ¥ This bottle holder shelf can be tilted in order to store previously opened bottles.
6 The -star compartment This compartment is suitable for freezing fresh food, for the storage of commercially frozen food and for ice cube making. Freezing fresh food T o freeze fresh foods it is not necessary to change the setting of the thermostat knob.
7 Because of consumer demand, preservatives have been removed from many pre-prepared foods. This together with the changes in shopping habits to a once-a-week shop, mean that safe handling and storage of food is even more important than ever .
8 The freezer compartment, however , will become progressively covered with frost. This should be removed with the special plastic scraper provided, whenever the thickness of the frost exceeds 4 mm. During this operation it is not necessary to switch off the power supply or to remove the foodstuffs.
9 Changing the light bulb Should the interior light fail to work, first switch off the appliance and disconnect from the electricity supply , then replace the bulb as follows: 1. Unscrew the light cover and then pull it outward by pressing as shown in the figure.
10 Something not W orking? Before contacting your local Service Force Centre check the following points. IMPORT ANT : If you call out an engineer to a fault listed below , or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee.
11 Service and Spare Parts In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Service Force Centre by telephoning:- 08705 929929 Y our telephone call will be automatically routed to the Service Force Centre covering your post code area.
Standard guarantee conditions We, Zanussi, undertake that if within 24 months of the date of purchase this Zanussi appliance or any part thereof is proved to be defective by reason only of faulty work.
13 POWER SUPPL Y VOL T AGE AND FREQUENCY 220-240 V / 50 Hz TOT AL POWER ABSORBED 140 W A VERAGE DAIL Y UNITS ELECTRICITY (*) 0,80 kWh TOT AL GROSS CAP ACITY 218 l NET CAP ACITY Fridge 193 l NET CAP ACITY compartment 17 l ST AR RA TING (*) This figure is based on standard test results in accordance with European Standard EN153.
14 Door reversal The applianceÕs door has been locked in position for transport by means of pins on both sides. According to the door opening direction, remove relevant pins at the top and at the bottom. Attention After completion of the door reversing operation, check that the door gasket adheres to the cabinet.
15 If you fit your own plug, the colours of the wires in the mains lead of your appliance, may not correspond with the markings identifying the terminals in your plug, proceed as follows: Connect the .
Dimensions of the recess Height of housing (1) mm 1225 Depth of housing (2) mm 550 Width of housing (3) mm 560 It is necessary that the cabinet has a ventilation recess with the following dimensions: Depth 50 mm Width 540 mm Building in PR0 540 50 3 2 1 For appropriate venting, follow indications in the figure.
17 PR266 A B C D 6. Place guide (A) on the inside part of the furniture door , up and down as shown in the figure and mark the position of external holes. After having drilled holes, fix the guide with the screws supplied. 20mm A 50mm PR166 PR33/2 C A 8.
.
.
© Electrolux plc 2004 923 458 614.
An important point after buying a device Zanussi ZI 9224 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Zanussi ZI 9224 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Zanussi ZI 9224 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Zanussi ZI 9224 you will learn all the available features of the product, as well as information on its operation. The information that you get Zanussi ZI 9224 will certainly help you make a decision on the purchase.
If you already are a holder of Zanussi ZI 9224, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Zanussi ZI 9224.
However, one of the most important roles played by the user manual is to help in solving problems with Zanussi ZI 9224. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Zanussi ZI 9224 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
