Instruction/ maintenance manual of the product ZI 918/8 KA Zanussi
Go to page of 20
REFRIGERA TOR- FREEZER ZI 918/8 KA INSTRUCTION BOOKLET 2223 248-73.
2 IMPOR T ANT SAFETY INFORMA TION It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transf erred to another ow.
3 CONTENTS Instructions f or the User Important Safety Information 2 Operation 4 Before use 4 Setting the temperature 4 The freezer compartment 4 F reezing fresh food 4 F rozen f ood storage 5 Thawing.
4 OPERA TION Before using Remov e all securing tapes. W ash inside the appliance with luke warm water and bicarbonate of soda (5 ml to 0.5 litre of water).
5 Normal Operating Sounds • Y ou may hear f aint gurgling or bub bling sounds when the refrigerant is pumped through the coils or tubing at the rear , to the cooling plate/ev aporator or to the fix ed freezer shelv es.
6 Mov able shelves The walls of the refrigerator hav e runners so that the shelves can be positioned as desired . For better use of space , the front half-shelves can lie ov er the rear ones. D338 P ositioning the door shelves T o per mit storage of f ood packages of v arious sizes, the door shelves can be adjusted in height.
7 Food Storage • T o obtain the best results from your appliance, neither hot foods nor liquids which ma y ev aporate, should be placed in the larder compar tment. • K eep the time between buying chilled f ood and placing it in your fridge as shor t as possible .
8 MAINTENANCE AND CLEANING Before an y maintenance or cleaning work is carried out, DISCONNECT the appliance from the ELECTRICITY supply . Internal cleaning Clean the inside and accessories with warm water and bicarbonate of soda (5ml to 0.5 litre of water).
9 Remember to wash the defrost cleaner in hot soap y water at regular intervals. Dry throughly before replacing. Freezer When the frost has reached a thickness of up to 4mm it can be remov ed using the ice scraper provided with the appliance. Dur ing this operation it is not necessary to disconnect the appliance from the mains and remov e the food.
10 SOMETHING NO T WORKING Symptom No power to the appliance The light does not come on The temperature in the fridge or freezer section is too high The freezer door will not open The compressor runs continously Excessive frost and ice has b uilt up Noise W ater under the salad bin Solution Check there is pow er at the sock et.
11 During a nor mal night time period of approximately 8 hours a traditional fridge freezer can normally maintain the frozen f ood temperature but if the appliance is left f or longer period in a low ambient the freezer will defrost . If, after the abo ve chec ks, there is still a f ault, call your local Service Force Centre.
12 Standard guarantee conditions We , Zanussi, undertake that if within 12 months of the date of the purchase this Zanussi appliance or any part thereof is prov ed to be defectiv e by reason only of f.
13 TECHNICAL SPECIFICA TIONS PO WER SUPPL Y V OL T AGE AND FREQUENCY 220-240 V / 50 Hz T O T AL POWER ABSORBED 100 W A VERA GE D AIL Y UNITS ELECTRICITY * 0.
14 INST ALLA TION P ositioning This appliance should only be installed at a location where the ambient temperature corresponds to the climate classification indicated on the rating plate, which is located at the left on the inside of the appliance.
15 Electrical connections Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. W ARNING: THIS APPLIANCE MUST BE EARTHED . The manufacturer declines an y liability should this safety measure not be observed.
16 Instructions for totall y built-in appliances Door rever sal Recess dimensions Height (1) 1446 mm Depth (2) 550 mm Width (3) 560 mm T o ensure adequate ventilation, allow the clearances shown in figure. 50 mm min. 200 cm 2 200 cm 2 min. D567 The appliance is supplied with the right or the left door opening.
17 Fit the appliance in the niche by making sure that it stands against the interior surface of the unit on the side where the door hinges of the appliances are fitted. Inser t the appliance until the upper strip butts up against the unit (1) and make sure that the low er hinge is in line with the surface of the unit (2).
18 Place guide (Ha) on the inside par t of the furniture door , up and down as shown in the figure and mark the position of external holes. After ha ving drilled holes, fix the guide with the screws supplied.
19 After completion of the door rev ersing operation, check that the door gask et adheres to the cabinet. If the ambient temperature is cold (i.e. in Winter), the gasket ma y not fit perfectly to the cabinet.
© Electrolux plc 2005.
An important point after buying a device Zanussi ZI 918/8 KA (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Zanussi ZI 918/8 KA yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Zanussi ZI 918/8 KA - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Zanussi ZI 918/8 KA you will learn all the available features of the product, as well as information on its operation. The information that you get Zanussi ZI 918/8 KA will certainly help you make a decision on the purchase.
If you already are a holder of Zanussi ZI 918/8 KA, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Zanussi ZI 918/8 KA.
However, one of the most important roles played by the user manual is to help in solving problems with Zanussi ZI 918/8 KA. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Zanussi ZI 918/8 KA along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
