Instruction/ maintenance manual of the product ZGF 982 Zanussi
Go to page of 16
GAS HOB ZGF 982 INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance GB.
2 Import ant Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 727727 Inst allation z .
3 This appliance complies with the following E.E.C. Directives: * 73/23 - 90/683 (Low V oltageDirective); * 93/68 (General Directives); * 89/336 (Electromagnetical Compatibility Directive) ; * 90/396 .
4 Operation Hob burners T o light a burner: z turn the relevant control knob anticlockwise to the maximum position, then push it down to ignite the burner; z then, check the flame is regular and adjust it as required. If you cannot light the flame even after several attempts, check the "cap" and “crown” (see Fig.
5 Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply . The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool.
6 Something Not W orking? If the hob is not working correctly , please carry out the following checks before contacting your local Service Force Centre.
7 Zanussi Guarantee conditions We, Zanussi, undertake that if, within 24 months of the date of the purchase, this Zanussi appliance or any part thereof is proved to be defective by any reason only of .
8 OVERALL DIMENSIONS Width: 860 mm Depth: 510 mm CUT OUT DIMENSIONS Width: 830 mm Depth: 480 mm SUPPLY CONNECTIONS Gas: R 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230 V 50 Hz supply , 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse.
9 FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE FITTING THE GAS HOB WITH A COOKER HOOD ABOVE 700 mm 400 mm 400 mm 100 mm 55 mm 50 mm 50 mm 600 mm 700 mm 400 mm 400 mm 100 mm 55 mm 600 mm 50 mm 50 mm.
10 Inst allation IMPORTANT: This hob must be installed by a competent person to the relevant Gas Standards. Any gas installation must be carried out by a competent person. The manufacturer will not accept liability , should the above instructions or any of the other safety instructions incorporated in this book be ignored.
11 FO 2564 FO 2044 3 Dimensions are given in mm. Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface.
12 Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed.
13 Fault Finding Preliminary Electrical Systems Check A. EARTH CONTINUITY CHECK - Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary . a ) T est leads from any appliance earth point to earth pin on plug.
14 Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ignitor does not spark Check .
15 Commissioning When the hob has been fully inst alled it will be necessary to check the minimum flame setting. T o do this, follow the procedure below . - T urn the gas tap to the MAX position and ignite. - Set the gas t ap to the MIN flame position then turn the control knob from MIN to MAX several times.
Grafiche MDM - Forlì 35672-5604 01/05 From the Electrolux Group. The world’s No.1 choice. The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use.
An important point after buying a device Zanussi ZGF 982 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Zanussi ZGF 982 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Zanussi ZGF 982 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Zanussi ZGF 982 you will learn all the available features of the product, as well as information on its operation. The information that you get Zanussi ZGF 982 will certainly help you make a decision on the purchase.
If you already are a holder of Zanussi ZGF 982, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Zanussi ZGF 982.
However, one of the most important roles played by the user manual is to help in solving problems with Zanussi ZGF 982. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Zanussi ZGF 982 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
