Instruction/ maintenance manual of the product ZGF 682 Zanussi
Go to page of 16
GAS HOBS ZGF 682 ZGF 692 INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance GB.
2 Guide to Use the instructions The following symbols will be found in the text to guide you throughout the Instructions: Safety Instructions S tep by step instructions for an operation Hints and T ip s Environmental Information Import ant Safety Information Y ou MUST read hese warnings carefully before inst alling or using the hob.
3 1. Hob T op 2. Auxiliary Burner 3. Semi-rapid Burners 4. Ultra-rapid Triple-crown Burner 5. Control knobs Description of the Hob This appliance complies with the following E.
4 Hob burners T o light a burner: z turn the relevant control knob anticlockwise to the maximum position, then push it down to ignite the burner; z then, check the flame is regular and adjust it as required. If you cannot light the flame even after several attempts, check the "cap" and “crown” (see Fig.
5 Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply . The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool.
6 Something Not W orking? If the hob is not working correctly , please carry out the following checks before contacting your local Service Force Centre. IMPORT ANT : If you call out an engineer to a fault listed below , or to repair a fault caused by incorrect use or inst allation, a charge will be made even if the appliance is under guarantee.
7 Zanussi Guarantee conditions W e, Zanussi, undertake that if, within 24 months of the date of the purchase, this Zanussi appliance or any part thereof is proved to be defective by any reason only of.
8 Rear Left Burner (semi-rapid) Heat Input 2.0 kW (6824 BTU/HR) Front Lef t Burner (auxiliary) Heat Input 1.0 kW (3412 BTU/HR) Rear Right Burner (semi-rapid) Heat Input 2.0 kW (6824 BTU/HR) Front Right Burner: ( Ultra-rapid T rip le- crown) Heat Input 4.
9 Import ant safety requirement s I CLEARANCES REQUIRED WHEN FITTING THE HOB WITHOUT A COOKER HOOD ABOVE CLEARANCES REQUIRED WHEN FITTING THE HOB WITH A COOKER HOOD ABOVE FO 0813 FO 0812 700 mm This h.
10 Rectangular cut-out size for hob A) End of shaft with nut B) W asher C) Elbow FO 0814 Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper . The connection should be suit able for connecting to RC 1/2 (1/2 BSP male thread).
11 FO 0763 FO 2564 FO 2044 1 2 3 FO 0199 a Fitting the Hob into the worktop ) Carry out the building in of the hob as follows: • place the seals supplied with the hob on the side edges of the cut ou.
12 Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed.
13 Fault Finding Preliminary Electrical Systems Check A. EARTH CONTINUITY CHECK - Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary . a ) T est leads from any appliance earth point to earth pin on plug.
14 Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ignitor does not spark Check .
15 Conversion from Natural Gas to LPG IMPORTANT The replacement/conversion of the gas hob should only be undertaken by a competent person. It is important to note that this model is designed for use w.
Grafiche MDM - Forlì 35670-9506 01/05 CUSTOMER CARE Zanussi 55-77 High S treet Slough Berkshire, SL1 1DZ T el: 08705 727727 © Electrolux plc 2003 From the Electrolux Group. The world’s No.1 choice. The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use.
An important point after buying a device Zanussi ZGF 682 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Zanussi ZGF 682 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Zanussi ZGF 682 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Zanussi ZGF 682 you will learn all the available features of the product, as well as information on its operation. The information that you get Zanussi ZGF 682 will certainly help you make a decision on the purchase.
If you already are a holder of Zanussi ZGF 682, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Zanussi ZGF 682.
However, one of the most important roles played by the user manual is to help in solving problems with Zanussi ZGF 682. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Zanussi ZGF 682 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
