Instruction/ maintenance manual of the product EMX620 Yamaha
Go to page of 18
E Owner’ s Manual Keep This Manual For Future Reference. 1 123 HIGH LOW MONI EFFECT PA D LEVEL –15 +15 –15 +15 01 0 01 0 01 0 2 HIGH LOW MONI EFFECT PA D LEVEL –15 +15 –15 +15 01 0 01 0 3 HI.
FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
Important 3 EMX620—Owner’s Manual Important Read the following before operating the EMX620 W arnings • Do not allow wate r to enter this unit or allow the unit t o become wet.
4 Important EMX620—Owner’s Manual Operating Notes • U sing a mobile telephone near this unit may induc e noise. I f noise occurs, use the telephone awa y from the unit. • XLR -ty pe connect ors are wired as follows: pin 1: ground, pin 2: hot (+), and pin 3: cold (–).
Introduction 5 EMX620—Owner’s Manual Introduction Thank you for pur chasing the Y amaha EMX620 P ower ed Mixer . In order to tak e full advantage of the EMX620 and enjoy long and trouble-free operation, read this owner’ s manual carefully , and keep it in a safe place for futur e reference.
6 Front & Rear Panels EMX620—Owner’s Manual Front & Rear Panels Control Panel ■ Channel Section The channel co nt r ols are used to set the EQ, MONI and EFFECT send levels, channel LEVEL, and P AD for each channel.
Control Panel 7 EMX620—Owner’s Manual ■ DIGIT AL EFFECT Section The DIGIT AL EFFECT section is used to turn the built-in digital effects processor on and off and select effects programs. F VOCAL, L. HALL, S. HALL switches These switches are used t o select the effects pro- grams: V OCAL, L.
8 Front & Rear Panels EMX620—Owner’s Manual N LIMITER indicator The LIMITER indicator lights up when the lim- iter circuit, which is designed to pr otect the inter - nal powe r amplifier against exc essive input signals and load mismatches, activates.
Input/Output Panel 9 EMX620—Owner’s Manual Input/Output Panel 1 Hi-Z, Lo-Z (inputs 1–4) These are the input c onnectors for input chan- nels 1 through 4. Both the Hi-Z and Lo-Z input can be used with microphones and, by using the P AD switch, can also be used with line-le vel sourc es, such as synthesiz ers and dr um machines.
10 Front & Rear Panels EMX620—Owner’s Manual I MAIN—OUTPUT jack The MAIN—OUTPUT jack outputs the MAIN bus signal after the 7-band graphic equalizer and MASTER level co ntrol, and can be connected to the input of a larger mix er , or a more pow erful amplifier , for example.
Rear Panel 11 EMX620—Owner’s Manual Rear Panel 1 POWER switch The PO WER switch is used to turn on and off the powe r to the EMX620. B SPEAKERS A & B jacks The SPEAKER A & B phone jacks output the main signal from the internal pow er amplifier and are used to c onnect speakers.
12 Front & Rear Panels EMX620—Owner’s Manual Hookup Example B — SPEAKERS — A Headphones Larger mixer or Amplifier Hi-Z Lo-Z Hi-Z Lo-Z Hi-Z Lo-Z Hi-Z LINE Lo-Z 1 LINE 2 INST 1 INST EFFECT OUT FOOT SW 2 PHONES MAIN MONITOR INPUT TO MAIN OUTPUT 11 22 T APE IN AUX IN REC OUT 88 *2 *1 *1.
Basic Operation 13 EMX620—Owner’s Manual Basic Operation Connecting Sour ces Before c onnecting any microphones or instru- ments, make sure that the EMX620 and an y other applicable equipment is turned off. Also make sure that the LE VEL control on each EMX620 input channel, and the MAIN MASTER and MONI MASTER contr ols are turned down.
14 Troubleshooting EMX620—Owner’s Manual T roubleshooting The following table describes the possible malfunctions of this demvice, and the appropriate actions to be taken in eac h case. Prob lem Cause Action Sound is no longer out- put from the speakers .
Specifications 15 EMX620—Owner’s Manual Speci fi cations ■ General Speci fi cations For E uropean M odel Pur chaser/U ser Information specified in EN55103-1 and EN55103-2. Inrush C ur rent: 23A Conformed En v ironment: E1, E2, E3 and E4 Maximum output po wer 135 W/8 Ω @0.
16 Specifications EMX620—Owner’s Manual ■ Input Speci fi cations ■ Output Speci fi cations • PHONE J ACKS are unbalanced. • 0 dB= 0.775 Vrms, 0 dBV= 1 Vrms.
Block & Level Diagrams 17 EMX620—Owner’s Manual ■ Block & Level Diagrams +30dB +20dB +10dB 0dB – 10dB – 20dB – 30dB – 40dB – 50dB +30dB +20dB +10dB 0dB – 10dB – 20dB – 30.
YAMAHA CORPORATION V474530 R1 1 IP 20 Pro Audio Division, #18/3 P.O. Box 3, Hamamatsu, 430-8651, Japan Printed in Taiwan.
An important point after buying a device Yamaha EMX620 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Yamaha EMX620 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Yamaha EMX620 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Yamaha EMX620 you will learn all the available features of the product, as well as information on its operation. The information that you get Yamaha EMX620 will certainly help you make a decision on the purchase.
If you already are a holder of Yamaha EMX620, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Yamaha EMX620.
However, one of the most important roles played by the user manual is to help in solving problems with Yamaha EMX620. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Yamaha EMX620 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
