Instruction/ maintenance manual of the product X Class Conversion to WES7 Wyse
Go to page of 18
Inst allation Guide Wyse ® X Class Conversion to WES7 Wyse ® USB Firmware T ool TM Release 1.10 Issue: 102910 PN: 883887-19L Rev . B.
Copyright Notices © 2010, Wyse T echnology Inc. All right s reserved. This manual and the software and firmware described in it are copyrighted. Y ou may not rep roduce, transmit, transcribe, store i.
Content s 1 Introduction 1 Kit Contents 1 Overview 2 Wyse T echnical Support 2 Related Document ation and Services 2 Wyse Online Community 2 2 Inst alling X90cw Mobile Thin Client Flash and RAM 3 Requ.
iv Contents This page intentionally blank..
1 Introduction This guide provides ste p-by-step in structions to convert X90cw mob ile thin clients from WES2009 to WES7. Caution WES7 firmware r equires X clas s mobile thin clients to have a min imum of 4 GB flash and 2 GB RAM. Tip After converting yo ur mobile thin clients, o btain any available firmwa re update a t http://www .
2 Chapter 1 The Conversion Sof tware Assembly DVD-ROM conta ins: • A PDF of this Reference Guide • Wyse USB Firmware T ool Release 1.10 • X Class WES7 Conver sion Image folder containing the following files: · bios.img · cmos.img · commandsXml.
2 Inst alling X90cw Mobile Thin Client Flash and RAM This chapte r contains inform ation for u sers of Wyse X90cw mobile thin clients who must install new flash and RAM. If you are installi ng firmware only , you can skip this chapter and proceed to"Installing WES7 Firmware.
4 Chapter 2 Figure 2 Removing the flash cover screws 5. Lift the flash cover to remove it and expos e the flash mo dule as sho wn in Figur e 3. Notice that the front of mobile the thin client is positioned at the bottom of the photo. Wa r n i n g Flash modules may be susceptible to da mage by Electro-S tatic Discharge (ESD).
Installing X90cw Mobile Th in Client Flash and RAM 5 9. Remove the screw from the RAM cover usin g a small Phillips Screwdriver as shown in Figure 4. Figure 4 Removing the RAM cover screw 10. Lift the RAM cov er to remo ve it and ex po se the RAM module as shown in Figure 5.
6 Chapter 2 12. Install the new RAM module in the revers e order of removing the original RAM modu le. Carefully press down on the RA M module until its retaining clip s lock it into place. 13. Replace the RAM cover in the reverse order as described in step s 10 and 9.
3 Inst alling WES7 Firmware This chapter include s the requirement s and procedures you nee d to install and use Wyse ® USB Firmware T ool TM to update your mobile thin client to WES7 firmware.
8 Chapter 3 S tep 3: Use Wyse USB Firmware T ool to Config ure a Single USB Key to Inst all Firmware 1. Double-click the shortcu t to run the tool an d open the Wyse USB Firmware T o ol wizard (the welcome p age provides the p roduct version and descriptio n, and a link to view the Wyse end user license agreemen t).
Installing WES7 Firmware 9 4. Select the Windows Embedded S t andard 7 OS type o ption. 5. Select the Up date Firmware operation to perform optio n. Tip Although the Preserve dat a p artition check bo.
10 Chapter 3 Figure 12 Prep are USB drive 11 . Select the USB key onto which you want the configurations (you can use Refresh as needed to recogn ize an inserted USB key), and then click Next . The pr ogress bar s show the ov erall prog ress and task pr ogress.
Installing WES7 Firmware 11 S tep 5: V erifying Mobile Thin Client Operation After the mob ile thin client reboots, yo u can verify the Ve r s i o n and that your general client information is cor rect. Figure 13 Client Info rmation (blank exa mple) 1.
12 Chapter 3 S tep 6: Attach a Wyse Conversion Label and Microso ft License Label on Each Converted Mobile Thin Client The conversion kit is suppl ied with Wyse Conversion Labels and Microsof t License Labels that must be atta ched to each mobile th in client as shown in Figures 14 and 15.
Installing WES7 Firmware 13 T roubleshooting This section contains ge neral troubleshooting information . USB Keys - T roubleshoot ing Boot Issues Due to differ ent manufacturing proce sses on U SB keys (and the variety of them), not all brands have been tested with the Wyse USB Firmware T ool.
Inst allation Guide Wys e ® X Class Conversion to WES7 Issue: 1029 10 Written and publishe d by: Wyse T echnology Inc., October 2010 Created using FrameMake r ® and Acrobat ®.
An important point after buying a device Wyse X Class Conversion to WES7 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Wyse X Class Conversion to WES7 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Wyse X Class Conversion to WES7 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Wyse X Class Conversion to WES7 you will learn all the available features of the product, as well as information on its operation. The information that you get Wyse X Class Conversion to WES7 will certainly help you make a decision on the purchase.
If you already are a holder of Wyse X Class Conversion to WES7, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Wyse X Class Conversion to WES7.
However, one of the most important roles played by the user manual is to help in solving problems with Wyse X Class Conversion to WES7. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Wyse X Class Conversion to WES7 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
