Instruction/ maintenance manual of the product WES2009 4GF Wyse
Go to page of 22
Reference Guide Wyse ® R Class Conversion, XPe to WES2009 Wyse ® USB Firmware T ool TM Release 1.10 Issue: 102910 PN: 883887-16L Rev . C.
Copyright Notices © 2010, Wyse T echnology Inc. All rights reserved. This manual and the software and firmware described in it are copyrighted. Y ou may not reproduce, transmit, transcribe, store in .
Content s 1 Introduction 1 Kit Contents 1 Overview 2 Wyse T echnical Support 2 Related Document ation and Services 2 Wyse Online Community 2 2 Inst alling R90L Thin Client Flash 3 Requirements 3 Proce.
iv Contents This page intentionally blank..
1 Introduction This guide pro vides step-b y-st ep instructions to convert R90L and R90LE thin client s from XPe to WES2009. Caution WES2009 firmware requires R class thin client s to have a minimum of 2GB flash. Note After conv erting your thin clie nts, ob tain any a vailable firmware update at http://www .
2 Chapter 1 The Conversion Sof tware Assembly DV D-ROM conta ins: • A PDF of this Reference Guide • Wyse USB Firmware T ool Release 1.10 • R Class WES Conversion Image folder cont aining the following files: · bios.img · cmos.img · commandsXml.
2 Inst alling R90L Thin Client Flash This chapter cont ains information for users of Wyse R90L thin client s who must install new flash. If you are installing firmw are only , you can skip this ch apter and proc eed to"Installing WES2009 Firmware.
4 Chapter 2 Procedures S tep 1: Remove the R90L Thin Client Lef t Side Cover Caution Follow all precautions listed in the Quick- S tart Guide that came with your thin client for disconne cting and reconnecting the thin client.
Installing R90L Thin Client Flash 5 S tep 2: Install the R90L Flash Module Wa r n i n g Flash modules may be susceptible to da mage by Electro-S tatic Discharge (ESD).
6 Chapter 2 This page intentionally blank..
3 Inst alling R90LE Thin Client Flash This chapte r contains inform ation for user s of Wyse R90LE thin clie nts who must inst all new flash. If you are installing firm ware only , you can skip this chapter and proceed to"Installing WES2 009 Firmware.
8 Chapter 3 Procedures S tep 1: Remove the R90LE Thin Client Lef t Side Cover Caution Follow all precautions listed in the Quick- S tart Guide that came with your thin client for disconne cting and reconnecting the thin client.
Installing R90LE Thin Client Flash 9 S tep 2: Install the R90LE Flash Module Wa r n i n g Flash modules may be susceptible to da mage by Electro-S tatic Discharge (ESD).
10 Chapter 3 Figure 8 Removing the existing f lash module 3. Install the new flash module in th e reverse order of removing the original flash module. Carefully press the flash module onto the st an dof f lock and connector , making sure to lock it into place.
4 Inst alling WES2009 Firmware This chapter include s the requirements and procedures you nee d to install and use Wyse ® USB Firmware T ool TM to update your thin client to WE S2009 firmware.
12 Chapter 4 S tep 3: Use Wyse USB Firmware T ool to Configure a Single USB Key to Convert Firmware 1. Double-click the shortcu t to run the tool an d open the Wyse USB Firmware T ool wizar d (the welcome p age provides the product version and descriptio n, and a link to view the Wyse end user license agreemen t).
Installing WES2 009 Firmware 13 4. Select the Windows Embedded St andard OS type option. 5. Select the Up date Firmware operation to perform option. Note Although the Preserve dat a partition check bo.
14 Chapter 4 Figure 15 Prep are USB drive 11 . Select the USB key onto which you want the configurations (you can use Refresh as needed to recogn ize an inserted USB key), and then click Next . The pr ogress bar s show the Overall Progr ess and task progress.
Installing WES2 009 Firmware 15 S tep 5: V erifying Thin Client Operation After the thin client reboo ts, you can veri fy that the general client information is correct.
16 Chapter 4 S tep 6: Atta ch a Wyse Co nversion Label and Microsof t License Label on Each Converted Thin Client The conversion kit is suppl ied with Wyse Conversion Labels and Microsof t License Labels that must be att ached to each thin client as shown in Figure s 17 and 18.
Installing WES2 009 Firmware 17 T roubleshooting This section contains ge neral troubleshooting information. USB Keys - T roubleshoot ing Boot Issues Due to differ ent manufacturing processes on U SB keys (and the variety of them), not all brands have been tested with the Wyse USB Firmware T ool.
Reference Guide Wys e ® R Class Conversion, XPe to WES2009 Issue: 1029 10 Written and publishe d by: Wyse T echnology Inc., October 2010 Created using FrameMake r ® and Acrobat ®.
An important point after buying a device Wyse WES2009 4GF (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Wyse WES2009 4GF yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Wyse WES2009 4GF - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Wyse WES2009 4GF you will learn all the available features of the product, as well as information on its operation. The information that you get Wyse WES2009 4GF will certainly help you make a decision on the purchase.
If you already are a holder of Wyse WES2009 4GF, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Wyse WES2009 4GF.
However, one of the most important roles played by the user manual is to help in solving problems with Wyse WES2009 4GF. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Wyse WES2009 4GF along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
