Instruction/ maintenance manual of the product Vanilla 125RL WTB
Go to page of 16
1 2002 FOX FORX Owners Manual FLOAT 80R - FLOAT 80RL - FLOAT 80RLC FLOAT 100R - FLOAT 100RL - FLOAT100RLC Vanilla 100R - Vanilla 100RL - Vanilla 100RLC Vanilla 125R - Vanilla 125RL - Vanilla 125RLC FOX RACING SHOX 130 Hangar Way, Watsonville, CA 95076 831.
2 FLOAT Forx Features One-piece Magnesium Lower Leg Double butted Aluminum Steerer PSC - Precision Steering Control CLS - Coil Lubrication System SDC - Shimmed Damping Control Rebound Adjustment FLOAT.
3 Table of Contents Introduction ................................................................. 4 Contact Information ..................................................... 4 Service / Warranty .......................................................
4 x o h S g n i c a R X O F y a W r a g n a H 0 3 1 6 7 0 5 9 A C , e l l i v n o s t a W 0 0 1 1 . 8 6 7 . 1 3 8 : e n o h P 9 6 4 7 . 9 6 3 . 0 0 8 : a c i r e m A h t r o N 2 1 3 9 . 8 3 7 . 1 3 8 : x a F m o c . x o h s g n i c a r x o f @ e c i v r e s : l i a m - Em o c .
5 Warranty Policy The factory warranty period for your fork is one year from the original date of purchase of the bicycle or fork. A copy of the original purchase receipt must accompany any fork being considered for warranty service. Warranty is at the full discre- tion of FOX Racing Shox and will cover only defective materials and workmanship.
6 Important Safety Information 1. Verify that the brakes are installed and adjusted properly before riding the bicycle. Improperly installed or adjusted brakes can cause loss of control and serious or fatal injuries to the rider. Use only “V” - style or hydraulic cantilever brakes or disc brakes designed by the manufacturer for use on FOX FORX.
7 Tire Sizes FOX FORX will accept tires sizes up to 2.40 inches wide (e.g. WTB MotoRaptor 55/60, 26 x 2.40 ). Any tire larger than 26 x 2.30 must be checked for clearance by the following method. Determining Tire Size - With the tire installed and inflated on the rim, measure the following three dimensions.
8 Service Intervals Your FOX FORX will perform best if serviced at the regular intervals shown below. m e t I h c a E r e t f A e d i R 5 2 y r e v E s r u o H 0 0 1 y r e v E s r u o H y l l a u n n .
9 General Set-Up Instructions Fork Terminology Travel: The total amount the fork compresses. Sag: The amount the fork compresses with the rider sitting on the bike in a normal riding position. Compression Damping: This controls the rate at which the fork compresses Rebound Damping: This controls the rate at which the fork extends.
10 Changing your Coil Spring 1. With a 26mm 6-point socket wrench, loosen and remove the preload topcap. Remove the black spring spacers (two spacers for 125mm travel, 1 for 100mm travel, none for 80mm travel). Compress the fork slightly and remove the coil spring.
11 Damping Adjustment Guidelines Rebound Adjustment (R, RL, RLC) FOX FORX feature a rebound adjuster. This allows the rider to control the speed at which the fork extends after compression. The Rebound Adjustment Knob is the red knob located on top of the right fork leg.
12 Changing Travel - FLOAT Forx FOX FORX travel can be changed by rearranging the travel spacers as shown in the drawings below. After changing travel check the fork for proper operation before riding.
13 Changing Travel - Vanilla Forx FOX FORX travel can be changed by rearranging the travel spacers as shown in the drawings below. After changing travel check the fork for proper operation before riding.
14 80mm 100mm 125mm Adjuster Knobs All Forx RL, RLC RLC Only Travel Spacers 25mm 20mm 20mm 25mm 20mm 25mm 20mm 25mm 20mm Preload Topcap Negative Spring Guide Plunger Shaft Changing Travel - Vanilla Fo.
15 Step 1 - Remove the blue air cap from the top of the left fork leg. Let the air out of the fork. Refer to Pump Instructions for details about letting the air out with a pump. Remove left top cap with a 26mm socket 6-point socket wrench. Step 2 - Loosen the bottom nut 3-4 turns with a 10mm wrench.
16 p/n: 605-00-003-A 2001 FOX Racing Shox, Inc., FOX Forx Owner’s Manual. The information herein is provided as a guide. FOX Racing Shox reserves the right to change all or part without notice. Changing Oil con’t Step 4 - Carefully pull the damper from the fork.
An important point after buying a device WTB Vanilla 125RL (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought WTB Vanilla 125RL yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data WTB Vanilla 125RL - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, WTB Vanilla 125RL you will learn all the available features of the product, as well as information on its operation. The information that you get WTB Vanilla 125RL will certainly help you make a decision on the purchase.
If you already are a holder of WTB Vanilla 125RL, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime WTB Vanilla 125RL.
However, one of the most important roles played by the user manual is to help in solving problems with WTB Vanilla 125RL. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device WTB Vanilla 125RL along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
