Instruction/ maintenance manual of the product EM/2 60, EM/2 72 Worksaver
Go to page of 42
OWNER’S MANUAL MODEL NO’ s EM/2 60 EM/2 72 CAUTION For Safe Operation Read Rules And Instructions Carefully SINO LEEINGLES, PIDA A YUDA A AIGUIEN QUE SI LO LEA P ARA QUE LE TRADUZCA LAS MEDIDAS DE SEGURIDAD. OWNER’S MANUAL MODEL NO’ s EM/2 60 EM/2 72 APRIL 2000 FS-FM001-OG F ARM ST A R P .
1 T ABLE OF CONTENTS CHECKLISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SAFETY INFORMA TION . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY SIGNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 DELIVER Y CHECKLIST Inspect the mower thoroughly after assembly to be cer- tain it is set up properly . The following checklist is a reminder of points to inspect. Check off each item as it is found satisfactory or after proper adjustment is made. h Check operator's manual and familiarize the opera- tor with all sections of it.
3 T o the Owner/Operator/Dealer All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded opera- tor who recognizes the potential hazards and follows reasonable safety practices.
4 37 EM/2 60 & EM/2 72 PTO P A R TS LIST SAFETY INSTRUCTIONS ( continued) Safety of the operator is one of the main concerns in designing and developing a new piece of equipment. Designers and manufacturers build in as many safety features as possible.
36 5 EM/2 60 & EM/2 72 PTO P A R T S D R A WING SAFETY INSTRUCTIONS ( continued) Keep safety signs clean and legible at all times. Replace safety signs that are missing or have become illegible. Replaced parts that displayed a safety sign should also display the current sign.
6 35 EM/2 60 & EM/2 72 GEARBOX P A R TS LIST SAFETY INSTRUCTIONS ( continued) Safety is a primary concern in the design and manufacture of our products. Unfortunately , our ef forts to pro- vide safe equipment can be wiped out by a single careless act of an operator .
34 7 EM/2 60 & EM/2 72 GEARBOX P A R T S D R A WING SAFETY INSTRUCTIONS ( continued) Never operate the tractor and mower until you have read and completely understand this manual, the T ractor Operator ’s Manual, and each of the Safety Messages found on the safety signs on the tractor and mower .
8 33 SAFETY INSTRUCTIONS ( continued) Mower operating power is supplied from tractor PTO. Refer to your tractor manual for PT O engagement and disengagement instructions. Always operate the tractor PTO in the 540 rpm speed selection. DO NOT OVER SPEED! Know how to stop tractor and mower quickly in case of an emergency .
32 9 EM/2 60 & EM/2 72 P A R T S D R A WING SAFETY INSTRUCTIONS ( continued) Never place hands or feet under mower with tractor engine running or before you are sure all motion has stopped. Stay clear of all moving parts. Do not reach or place yourself under equipment until it is blocked securely .
10 31 SAFETY INSTRUCTIONS ( continued) Stop mower and tractor immediately upon striking an obstruction. T urn engine off, remove key , inspect and repair any damage before resuming operation. The mower discharge deflectors, belt guards, driveline and gearbox shields should be used and maintained in good working condition.
30 11 SAFETY INSTRUCTIONS ( continued) Comply with state and local laws governing highway safety and movement of farm machinery on public roads. The use of flashing amber lights is acceptable in most localities. However , some localities prohibit their use.
12 29 SAFETY INSTRUCTIONS ( continued) Good maintenance is your responsibility . Poor maintenance is an invitation to trouble. Follow good shop practices. - Keep service area clean and dry . - Be sure electrical outlets and tools are properly grounded.
28 13 MAINTENANCE INSTRUCTIONS ( continued) SAFETY INSTRUCTIONS ( continued) After servicing, be sure all tools, parts and service equipment are removed. Check to ensure all safety signs are installed and in good condition. (See safety sign section for location drawing.
14 27 MAINTENANCE INSTRUCTIONS ( continued) SAFETY SIGN LOCA TION DRIVE BEL T ADJUSTMENT 1. Shut off mower and tractor . 2. Loosen all four nuts (Item 1) on the gearbox slide plate (Item 2). See figure 14. 3. Loosen jam nut (Item 3) on the tension adjustment bolt (Item 4) 4.
26 15 MAINTENANCE INSTRUCTIONS ( continued) SAFETY SIGNS W ARNING! When attaching the driveline yoke to the tractor PTO shaft, it is important that the spring activated locking collar turns freely and that the locking pin is seated on the PTO shaft groove.
16 25 SAFETY SIGNS MAINTENANCE INSTRUCTIONS W ARNING! Always disengage the tractor PTO before raising the mower for transport or making adjustments. LUBRICA TION Do not let excess grease collect on or around parts, par- ticularly when operating in sandy areas.
24 17 DRIVELINE SAFETY SIGNS TROUBLESHOOTING ( continued) PROBLEM POSSIBLE CAUSE SOLUTION Belt slippage Mower is overloading, grass is too Slow tractor ’s ground speed but tall or heavy maintain 540 RPM PTO speed.
18 23 TRACTOR REQUIREMENTS AND PREP A R A TION The models EM/2 60 and EM/2 72 Finishing Mowers are designed for light duty cutting such as lawn main- tenance with a Category I, 3 pt. hitch and with a 540 rpm PTO. These mowers are not designed for tractors over 40 horsepower .
22 19 ASSEMBL Y INSTRUCTIONS The mower will attach to most tractors with a Category I, 3 pt. hitch system and a 540 RPM PTO. Do not exceed horsepower recommendations. DANGER! Operating with PTO speed over 540 RPM can cause excessive vibration and mower failure, which can result in serious injury or even death.
20 21 OPERA TION INSTRUCTIONS ( continued) CUTTING HEIGHT ADJUSTMENT Important: Avoid very low cutting heights.Striking the ground with the blades gives the most damaging shock loads a mower can encounter and will cause damage to it and the driveline.
20 21 OPERA TION INSTRUCTIONS ( continued) CUTTING HEIGHT ADJUSTMENT Important: Avoid very low cutting heights.Striking the ground with the blades gives the most damaging shock loads a mower can encounter and will cause damage to it and the driveline.
22 19 ASSEMBL Y INSTRUCTIONS The mower will attach to most tractors with a Category I, 3 pt. hitch system and a 540 RPM PTO. Do not exceed horsepower recommendations. DANGER! Operating with PTO speed over 540 RPM can cause excessive vibration and mower failure, which can result in serious injury or even death.
18 23 TRACTOR REQUIREMENTS AND PREP A R A TION The models EM/2 60 and EM/2 72 Finishing Mowers are designed for light duty cutting such as lawn main- tenance with a Category I, 3 pt. hitch and with a 540 rpm PTO. These mowers are not designed for tractors over 40 horsepower .
24 17 DRIVELINE SAFETY SIGNS TROUBLESHOOTING ( continued) PROBLEM POSSIBLE CAUSE SOLUTION Belt slippage Mower is overloading, grass is too Slow tractor ’s ground speed but tall or heavy maintain 540 RPM PTO speed.
16 25 SAFETY SIGNS MAINTENANCE INSTRUCTIONS W ARNING! Always disengage the tractor PTO before raising the mower for transport or making adjustments. LUBRICA TION Do not let excess grease collect on or around parts, par- ticularly when operating in sandy areas.
26 15 MAINTENANCE INSTRUCTIONS ( continued) SAFETY SIGNS W ARNING! When attaching the driveline yoke to the tractor PTO shaft, it is important that the spring activated locking collar turns freely and that the locking pin is seated on the PTO shaft groove.
14 27 MAINTENANCE INSTRUCTIONS ( continued) SAFETY SIGN LOCA TION DRIVE BEL T ADJUSTMENT 1. Shut off mower and tractor . 2. Loosen all four nuts (Item 1) on the gearbox slide plate (Item 2). See figure 14. 3. Loosen jam nut (Item 3) on the tension adjustment bolt (Item 4) 4.
28 13 MAINTENANCE INSTRUCTIONS ( continued) SAFETY INSTRUCTIONS ( continued) After servicing, be sure all tools, parts and service equipment are removed. Check to ensure all safety signs are installed and in good condition. (See safety sign section for location drawing.
12 29 SAFETY INSTRUCTIONS ( continued) Good maintenance is your responsibility . Poor maintenance is an invitation to trouble. Follow good shop practices. - Keep service area clean and dry . - Be sure electrical outlets and tools are properly grounded.
30 11 SAFETY INSTRUCTIONS ( continued) Comply with state and local laws governing highway safety and movement of farm machinery on public roads. The use of flashing amber lights is acceptable in most localities. However , some localities prohibit their use.
10 31 SAFETY INSTRUCTIONS ( continued) Stop mower and tractor immediately upon striking an obstruction. T urn engine off, remove key , inspect and repair any damage before resuming operation. The mower discharge deflectors, belt guards, driveline and gearbox shields should be used and maintained in good working condition.
32 9 EM/2 60 & EM/2 72 P A R T S D R A WING SAFETY INSTRUCTIONS ( continued) Never place hands or feet under mower with tractor engine running or before you are sure all motion has stopped. Stay clear of all moving parts. Do not reach or place yourself under equipment until it is blocked securely .
8 33 SAFETY INSTRUCTIONS ( continued) Mower operating power is supplied from tractor PTO. Refer to your tractor manual for PT O engagement and disengagement instructions. Always operate the tractor PTO in the 540 rpm speed selection. DO NOT OVER SPEED! Know how to stop tractor and mower quickly in case of an emergency .
34 7 EM/2 60 & EM/2 72 GEARBOX P A R T S D R A WING SAFETY INSTRUCTIONS ( continued) Never operate the tractor and mower until you have read and completely understand this manual, the T ractor Operator ’s Manual, and each of the Safety Messages found on the safety signs on the tractor and mower .
6 35 EM/2 60 & EM/2 72 GEARBOX P A R TS LIST SAFETY INSTRUCTIONS ( continued) Safety is a primary concern in the design and manufacture of our products. Unfortunately , our ef forts to pro- vide safe equipment can be wiped out by a single careless act of an operator .
36 5 EM/2 60 & EM/2 72 PTO P A R T S D R A WING SAFETY INSTRUCTIONS ( continued) Keep safety signs clean and legible at all times. Replace safety signs that are missing or have become illegible. Replaced parts that displayed a safety sign should also display the current sign.
4 37 EM/2 60 & EM/2 72 PTO P A R TS LIST SAFETY INSTRUCTIONS ( continued) Safety of the operator is one of the main concerns in designing and developing a new piece of equipment. Designers and manufacturers build in as many safety features as possible.
3 T o the Owner/Operator/Dealer All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded opera- tor who recognizes the potential hazards and follows reasonable safety practices.
2 DELIVER Y CHECKLIST Inspect the mower thoroughly after assembly to be cer- tain it is set up properly . The following checklist is a reminder of points to inspect. Check off each item as it is found satisfactory or after proper adjustment is made. h Check operator's manual and familiarize the opera- tor with all sections of it.
1 T ABLE OF CONTENTS CHECKLISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SAFETY INFORMA TION . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY SIGNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OWNER’S MANUAL MODEL NO’ s EM/2 60 EM/2 72 CAUTION For Safe Operation Read Rules And Instructions Carefully SINO LEEINGLES, PIDA A YUDA A AIGUIEN QUE SI LO LEA P ARA QUE LE TRADUZCA LAS MEDIDAS DE SEGURIDAD. OWNER’S MANUAL MODEL NO’ s EM/2 60 EM/2 72 APRIL 2000 W S-FM001-OG WORKSAVER, INC.
An important point after buying a device Worksaver EM/2 60, EM/2 72 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Worksaver EM/2 60, EM/2 72 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Worksaver EM/2 60, EM/2 72 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Worksaver EM/2 60, EM/2 72 you will learn all the available features of the product, as well as information on its operation. The information that you get Worksaver EM/2 60, EM/2 72 will certainly help you make a decision on the purchase.
If you already are a holder of Worksaver EM/2 60, EM/2 72, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Worksaver EM/2 60, EM/2 72.
However, one of the most important roles played by the user manual is to help in solving problems with Worksaver EM/2 60, EM/2 72. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Worksaver EM/2 60, EM/2 72 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
