Instruction/ maintenance manual of the product FV-HD45 Winegard
Go to page of 24
Mast not included with antenna. WARNING Installation of this antenna near power lines is dangerous. For your safety , follow the installation instructions. Instruction Manual For Models FV -HD45/FVHD45C F reeVision ® Antenna Made in U .S.A. (Designed for use with 54–698 MHz DTV frequencies.
Front Assembly (UHF) P arts List Clip Back Assembly (VHF) U-Bolt Element Extensions (8) Large Screw (2) Mast Clamp Insert Large Flange Nut for U-Bolt (2) Small Flange Nut (17) Large Screw Small Flange.
Things to Consider Before Installing the Antenna Location Selection The digital broadcast signal travels line of sight. The fewer objects between your antenna and the broadcast tower , the stronger your signal will be.
Assembling the Antenna Start by unfolding the VHF elements on the back assembly until the elements are perpendicular to the boom (Figure 1). Y ou should hear the elements click into place. Boom VHF Elements Figure 1 Unfold the six UHF elements on the front assembly until they are perpendicular to the boom.
Slide the crimped end of the front assembly boom into the open end of the back assembly boom (Figure 4). Re-insert the screw into the plastic block closest to the mast clamp, and secure with the flange nut. Figure 4 Crimped End Then, slip the phasing lines onto the threaded rivets near the reflector brackets.
6 Tighten the two flange nuts. See Figure 9. Insert the open end of one corner reflector in-between the top of the reflector brackets (Figure 7). (Elements should be on top.) Align the holes in the brackets with the hole in the corner reflector . Insert a large screw through the holes.
7 Adding the Low Band VHF Add- On Kit For RF Channels 2–6 and/or FM Locate the hole in the bottom of the boom near the mast clamp. Insert the large screw through the hole in the bottom of the boom (Figure 11). Place the element extension with crimped ends onto the screw .
8 Shortest Element Extension Figure 12 Longest Element Extension Place each element extension beside the element to which it will connect. The shortest element extension will connect to the shortest element on the back assembly , and the longest element extension will connect to the longest element.
Locate the two posts on the underside of the front assembly (Figure 14). Place two washers on each post. Loosely thread a small nut onto each post. Slide one fork of the matching transformer between a set of washers. Repeat for the other fork on the other post.
1) 2) 3) 4) P roviding Lightning P rotection for the Antenna Mount lightning arrestor or 75 ohm grounding block as close as possible to where lead-in enters house. Ground wires for both mast and lead-in should be copper or aluminum wire, number 8 or larger .
Issue P ossible Cause There is static or snow in the picture. Digital television is all or nothing; the picture is crystal clear , or there isn ’t one.
WinegardCompany•3000KirkwoodStreet•Burlington,IA52601 319-754-0600•F ax319-754-0787•www .winegard.com Printed in U .
El mástil no se incluye con la antena. ADVERTENCIA La instalación de esta antena cerca de líneas eléctricas es peligrosa. P or su seguridad, siga las instrucciones de instalación.
Conjunto Delantero (UHF) Lista de P artes Broche Conjunto T rasero (VHF) P erno U Extensiones de Elemento (8) T ornillo Grande (2) Inserto de la Abrazadera del Mástil T ornillo Grande T uerca de Brid.
Lo que se Debe Considerar Antes de Instalar la Antena Selección de la Ubicación La señal de transmisión digital viaja en la línea de la visión. Entre menos objetos haya entre su antena y la torre de transmisión, más fuerte será su señal.
Ensamble de la Antena Inicie desplegando los elementos VHF en el conjunto trasero hasta que los elementos estén perpendiculares a la pluma (Figura 1). Debe escuchar que los elementos hacen clic en su lugar . Pluma Elementos VHF Figura 1 Despliegue los seis elementos UHF en el conjunto delantero hasta que estén perpendiculares a la pluma.
Deslice el extremo encapsulado de la pluma del conjunto delantero en el extremo abierto de la pluma del conjunto trasero (Figura 4). V uelva a insertar el tornillo en el bloque de plástico más cercano a la abrazadera del mástil, y asegure con la tuerca de brida.
6 Apriete las dos tuercas de brida. V ea la Figura 9. Inserte el extremo abierto de un reflector de esquina en medio de la parte superior de los soportes del reflector (Figure 7). (L os elementos deben estar en la parte superior .) Alinee los orificios en los soportes con el orificio en el reflector de esquina.
7 Agregando el Kit Adicional VHF de Banda Baja P ara Canales 2–6 de RF y FM Localice el orificio en la parte inferior de la pluma cerca de la abrazadera del mástil. Inserte el tornillo grande a través del orificio en la parte inferior de la pluma (Figura 11).
8 Extensión de Elemento Más Corta Figura 12 Extensión de Elemento Más Larga Coloque cada extensión de elemento al lado del elemento al que se conectará. La extensión de elemento más corta se conectará al elemento más corto en el conjunto trasero, y la extensión de elemento más larga se conectará al elemento más largo.
Localice los dos postes en la parte inferior del conjunto delantero (Figura 14). Coloque dos arandelas en cada poste. Enrosque sin apretar una tuerca pequeña sobre cada poste. Deslice una horquilla del transformador de acoplamiento entre un juego de arandelas.
1) 2) 3) 4) P roporcionando P rotección Contra Relámpagos para la Antena Monte el pararrayos o el bloque de conexión a tierra de 75 ohmios tan cerca como sea posible a donde la introducción entra a la casa. Los cables de conexión a tierra para el mástil y la introducción deben ser de cobre o de aluminio, número 8 ó mayor .
Problema Causa probable Hay estática o nieve en la imagen. La televisión digital es todo o nada; la imagen es clara como el cristal, o no hay imagen. La estática significa que existe interferencia entre el sintonizador digital y la pantalla de la televisión.
WinegardCompany•3000KirkwoodStreet•Burlington,IA52601 319-754-0600•F ax319-754-0787•www .winegard.com Impreso en Estados Unidos © 2011 Winegard Compa.
An important point after buying a device Winegard FV-HD45 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Winegard FV-HD45 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Winegard FV-HD45 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Winegard FV-HD45 you will learn all the available features of the product, as well as information on its operation. The information that you get Winegard FV-HD45 will certainly help you make a decision on the purchase.
If you already are a holder of Winegard FV-HD45, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Winegard FV-HD45.
However, one of the most important roles played by the user manual is to help in solving problems with Winegard FV-HD45. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Winegard FV-HD45 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
