Instruction/ maintenance manual of the product W338 White
Go to page of 12
1 Please r ead the instr uction manual car efully befor e operating the machine. Sew E-Z Model W338 Mini Sewing Machine Instruction Manual Call T oll Fr ee 800-331-3164 www .
2 Introduction Bobbin compar tment (I) Bobbin (S) Needle (R) Needle Clamp (P) Needle Clamp Screw (O) T ension Screw (Q) T ake Up Lever (D) Thread Spindle (C) Thread Spool (E) Bobbin Holder (V) Bobbin .
3 Par ts & Accessories Foot Pedal Jack (M) AC/DC Adapter (DC 6V) Accessories Needle Threader , T ape measure, Seam ripper , Needles, Thimble, Thread, Buttons, Pins, Scissors, Bobbins, Snaps.
4 Battery Installation Battery Installation 1. Caution: Make cer tain the POWER SWITCH is in the of f position befor e inser ting the batteries. 2. Inser t (4)AA batteries in the batter y slot compar tment in the bottom of the machine. Be cer tain the batteries ar e in the corr ect polarities as marked on the machine.
5 Threading the machine Threading the machine 1. Raise thread spindle (C) by grasping the exposed top and pulling upward until thread spindle (C) is fully extended.
6 Bobbin Winding and Inser tion Winding the bobbin Y ou can wind your own bobbins with thread from spools you purchase separately to have a vir tually unlimited thread color selection. Match your fabrics or contrast with the thread shades of your choice.
7 Operating the Sew E-Z Pr ess the power switch to begin sewing. Don’t pull the fabric. Rotate the handwheel to bring the needle to the highest position.
8 Operating the Sew E-Z Controlling the Sewing Speed The machine has two speeds of sewing control. In the “H” position the switch is in, while in the “L” position the switch is out. W e recommend using the slow speed at the beginning. When you become more experienced and feel confident controlling the machine, you can use the fast speed.
9 Operating the Sew E-Z Adjusting thread tension T ension for maximum per for mance has been set and adjusted at the factor y . However , if you should find that stitches are too loose, or too tight, you can adjust the stitch. 1. Loosen stitch by turning the tension screw (Q) counter-clockwise.
10 Changing the Needle 1. T ur n the handwheel (K) clockwise to raise the needle (R) to its highest position. 2. Loosen the needle clamp screw (O) by turning it counter-clockwise (toward you). Y ou may need to use a shor t slotted screwdriver or small pliers.
11 Precautions 1. The sewing machine does not run when the power switch is pressed. •Batteries are inser ted incorrectly . Inser t the batteries again using the diagram provided inside the batter y compar tment. •Batteries are exhausted. Replace with new batteries.
12 ©2006 VSM Sewing Inc. White is a registered trademark. All rights reser ved..
An important point after buying a device White W338 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought White W338 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data White W338 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, White W338 you will learn all the available features of the product, as well as information on its operation. The information that you get White W338 will certainly help you make a decision on the purchase.
If you already are a holder of White W338, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime White W338.
However, one of the most important roles played by the user manual is to help in solving problems with White W338. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device White W338 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
