Instruction/ maintenance manual of the product 1F89-0211 White Rodgers
Go to page of 16
1 Blue 2” Heat Pump Ther mostat Heat Pump Installation and Operating Instructions Save these instructions f or future use! F AILURE T O READ AND FOLLO W ALL INSTR UCTIONS CAREFULL Y BEFORE INST ALLING OR OPERA TING THIS CONTROL COULD CA USE PERSONAL INJUR Y AND/OR PROPER TY D AMA GE.
2 REMO VE OLD THERMOST A T 1. Shut off electricity at the main fuse box until installation is complete. Ensure that electrical power is disconnected. 2. Remov e the front cov er of the old ther mostat. With wires still attached, remov e w all plate from the wall.
3 WIRING DIA GRAM L R C 24 VA C 120 VA C Hot SYSTEM MONITOR SWITCH Neutral THERMOS TAT SYSTEM G W2 Figure 2. T ypical wiring diagram for single transf ormer systems TRANSFORMER (Class II Current Limit.
4 INST ALLER/CONFIGURA TION MENU The configuration menu allows you to set cer tain ther mostat operating characteristics to your system or personal requirements. T o enter the menu: Set y our thermostat switch to OFF . Press and hold the and buttons simultaneously f or appro ximately 5 seconds.
5 5) Select Backlight Display - The displa y bac klight impro ves displa y contrast in lo w lighting conditions. When the “C” terminal is connected, selecting backlight CdL On will keep the light on continuously . Select backlight OFF will tur n the light on momentarily when any ke y is pressed.
6 TR OUBLESHOO TING Reset Operation If a voltage spike or static discharge blanks out the display or causes erratic ther mostat operation, y ou may need to reset the ther mostat. T o reset, the System Switch must be in Cool, HEA T , or EMER . Sim ultaneously hold the and buttons f or approximately 10 seconds until the display goes blank.
7 ST A GING Second Stage - A uxiliary Heat Most heat pump systems hav e an A uxiliary or Second Stage electric heater or gas fur nace. Heat produced by a heat pump is economical but may not alwa ys hav e the capacity to maintain a comf or table room temperature setting.
White-Rodgers is a division of Emerson Electric Co. The Emerson logo is a trademark and service mar k of Emerson Electric Co. Homeowner Help Line: 1-800-284-2925 www .
White-Rodgers es una división de Emerson Electric Co. El logotipo de Emerson es una marca comercial y una marca de servicio de Emerson Electr ic Co. Línea de ayuda para el usuario: 1-800-284-2925 www .
7 ET AP AS Segunda etapa - Calor auxiliar La ma yoría de los sistemas de bomba de calor tiene un calentador eléctrico o un calefactor de gas auxiliar o de segunda etapa. El calor producido por una bomba de calor es económico pero no siempre tiene la capacidad necesaria para mantener un valor de temper atura ambiente conf or table.
6 SOLUCIÓN DE PR OBLEMAS Operación de reajuste Si un pico de voltaje o una descarga estática pone en blanco la pantalla o hace que el ter mostato funcione de manera errática es posible que necesite reajustar el ter mostato . P ara reajustar , el interruptor del sistema tiene que estar en Cool, HEA T , o EMER .
5 5) Seleccione luz de fondo de la pantalla - La luz de fondo mejora el contraste de la pantalla en condiciones de poca luz. Cuando la terminal “C” está conectada, la selección de CdL On mantendrá la luz de fondo encendida de f orma contin ua.
4 MENÚ INST ALADOR/DE CONFIGURA CIÓN El menú de configuración le per mite ajustar cier tas características operativ as del ter mostato según el sistema o sus necesidades par ticulares. P ara ingresar en el menú: Ajuste el interr uptor del ter mostato en OFF .
3 CONEXION ELÉCTRICAS L R C 24 VCA 120 VCA Vivo INTERRUPT OR MONITOR DEL SISTEMA Neutro SISTEMA TERMOS TAT O G W2 Figura 2. Diagrama de conexiones típico para sistemas de un solo transf ormador TRAN.
2 RETIRE EL TERMOST A T O VIEJO 1. Apague la electricidad en la caja de fusibles pr incipal hasta que ha ya finalizado la instalación. Asegúrese de que la alimentación eléctrica esté desconectada. 2. Retire la cubier ta delanter a del ter mostato viejo .
1 T er mosta to de bomba de calor Blue 2 pulg. Bomba de calor Instrucciones de instalación y operación ¡Conserve estas instrucciones para consultarlas en cualquier momento! EL NO LEER Y SEGUIR CON CUID ADO T OD AS LAS INSTRUCCIONES ANTES DE INST ALAR O UTILIZAR ESTE CONTROL PODRÍA CA USAR LESIONES PERSONALES Y/O D AÑOS MA TERIALES.
An important point after buying a device White Rodgers 1F89-0211 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought White Rodgers 1F89-0211 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data White Rodgers 1F89-0211 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, White Rodgers 1F89-0211 you will learn all the available features of the product, as well as information on its operation. The information that you get White Rodgers 1F89-0211 will certainly help you make a decision on the purchase.
If you already are a holder of White Rodgers 1F89-0211, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime White Rodgers 1F89-0211.
However, one of the most important roles played by the user manual is to help in solving problems with White Rodgers 1F89-0211. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device White Rodgers 1F89-0211 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
