Instruction/ maintenance manual of the product BE815 Belling
Go to page of 28
BE815 Combi Fridge Freezer INSTALLATION AND USER INSTRUCTIONS You must read these instructions prior to using the appliance and retain them for future reference.
.
Cor. er.s Introduction & safety warnings .......................................................................... 2 Electrical requirements ..................................................................................... 3 Transportation instructions .
Congratulations on your choice of a quality Appliance which has been designed to give you service for many years. WARNING ! IMPORTANT ! DO NOT connect your appliance to the electricity supply until all packing and transit protectors have been removed.
GREEN & YELLOW OR GREEN N BLUE OR BLACK BROWN OR RED V) t i C O CORD GRIP C D ELECTRICAL REQUIREMENTS Before you insert the plug into the wall socket make sure that the voltage and the frequency shown in the rating plate inside the appliance corresponds to your electricity supply.
TRANSPORTATION INSTRUCTIONS 1. The appliance should be transported only in a vertical upright position. The packing as supplied must be intact during transportation. 2. If during the course of transport the appliance has to be transported horizontally, it must only be laid on its left hand side when standing in the front of the appliance.
This fridge freezer has been designed to operate in ambient temperatures between +5 and +32 degrees C (41 and 90 degrees F) Therefore if the appliance is installed in an unheated/cold room (eg: conser.
FROZEN FOOD STORAGE DRAWERS DEFROST WATER COLLECTION CHANNEL GETTING TO KNOW YOUR COMBI FRIDGE / FREEZER DAIRY COMPARTMENT EGG TRAY THERMOSTAT KNOB INTERIOR LIGHT ( 1 ,•• ,• WINE RACK CABINET SH.
SUGGESTED ARRANGEMENT OF FOOD IN THE FRIDGE/FREEZER Arrangement Examples (See diagram) 1. Baked, chilled cooked food, dairy products, cans. 2. Wine 3. Meat, sausages, cold cuts. 4. Fruit, vegetables, salads. 3 5. Frozen food and freezing of fresh food.
TEMPERATURE CONTROL AND ADJUSTMENT Operating temperatures are controlled by the thermostat knob (see diagram) located on the ceiling of fridge compartment.
STARTING Final Check Before you start using the fridge/freezer check that: 1. The interior is dry and air can circulate freely at the rear of the cabinet. 2. Clean the interior as recommended under "CLEANING AND CARE." 3. Insert the plug into the wall socket and switch on the electricity supply.
FREEZING FRESH FOOD Please observe the following instructions to obtain the best results. Do not freeze too large a quantity at any one time. The quality of the food is best preserved when it is frozen right through to the core as quickly as possible.
DEFROSTING A) FRIDGE COMPARTMENT The fridge compartment defrosts automatically. The defrosting water runs to the drain tube via a collectioncontainer at the back of the appliance (1). (see diagram) During defrosting water droplets may form at the back of the fridge compartment where concealed evaporator is located.
CLEANING AND CARE " We recommend that you switch off the appliance at the socket outlet and pull out the mains plug before cleaning. ** Never use any sharp abrasive instrument, soap, household cleaner, detergent and wax polish for cleaning. " Use luke warm water to clean the cabinet of the appliance and wipe it dry.
REPLACING THE INTERIOR LIGHT BULB (See diagram) Should the light fail to work, proceed as follows. 1. Switch off at the socket outlet and pull out the mains plug.
DO'S AND DON'TS Do- Clean and defrost your appliance regularly (See "Defrosting") Do- Keep raw meat and poultry below cooked food and dairy products. Do- Take off any unusable leaves on vegetables and wipe off any soil. Do- Leave lettuce, cabbage, parsley and cauliflower on the stem.
ENERGY SAVING TIPS 1- Ensure your appliance is installed in a well ventilated area. If the ambient temperature is low (but in no case lower than 5 degrees C), then the energy saving will be more.
es) cc min. 200 cm 2 1 min. 200 cm 2 INSTALLATION INSTRUCTIONS (All dimensions are in mm) Ventilation CD OD N OD 0 0 16.
Ventilation Ventilation 200 cm2 200 cm 2 Ventilation requirement 17.
• 4 Parts are supplied in the plastic bag. Fit plastic trims and door furniture brackets supplied with the product. 18.
19.
2 mri l l * ". t 4* *_, 2 mOss.k Ensure 2 mm gaps are obtained, adjust if necessary. 20.
REVERSING THE DOORS Reverse the doors following numbered instructions..
GUARANTEE DETAILS Your new Belling product is guaranteed against the cost of breakdown repairs for twelve months from the date of the original purchase. W hat is covered? • Repairs necessary as a result of faulty materials, defective components or manufac- turing defect.
HOW TO OBTAIN SERVICE Please keep your purchase receipt or other proof of purchase in a safe place; you will need to have it should the product require attention under guarantee. You should also complete the details below; it will help us assist you when requesting service.
Technical data Performance Energy efficiency class Energy consumption - Kwh / year Net storage - vol fresh food litres (cu. ft) Net storage - vol frozen food Itrs (cu.
WIRING DIAGRAM 25.
BELLING CUSTOMER CARE In case of difficulty within the UK, please call Belling Customer Care Centre Helpline on 0871 22 22 503 When you dial this number you will hear a recorded message and be given a number of options. This indicates that your call has been accepted and is being held in a queue.
An important point after buying a device Belling BE815 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Belling BE815 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Belling BE815 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Belling BE815 you will learn all the available features of the product, as well as information on its operation. The information that you get Belling BE815 will certainly help you make a decision on the purchase.
If you already are a holder of Belling BE815, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Belling BE815.
However, one of the most important roles played by the user manual is to help in solving problems with Belling BE815. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Belling BE815 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
