Instruction/ maintenance manual of the product H-2412G Wells
Go to page of 16
PRINTED IN UNITED ST A TES OF AMERICA WELLS BLOOMFIELD, LLC 2 ERIK CIRCLE, P . O. Box 280 V erdi, NV 89439 www .wellsbloomfield.com telephone: 775-689-5703 fax: 775-689-5976 IMPORTANT: DO NOT DI SCARD.
M228 306916 OpM H-2412 Instant-On Dual Pilot Gas Hotplate Unless otherwise specified, all commercial cooking equipment manufactured by WELLS BLOOMFIELD, LLC is warranted against defects in ma terials .
W A R R A N T Y x i S P E C I F I C A T I O N S 1 FEATURES & OPERATING CONTROLS 2 PRECAUTIONS & GENERAL INFORMATION 3 AGENCY APPROVAL INFORMATION 3 I N S T A L L A T I O N 4 I N I T I A L A D .
BURNERS Provide cooking heat Front and rear burners are individually controllable Removable for easy cleaning BURNER CONTROL Provide individual control of front and re ar burners KNOBS PILOT LIGHT Provides ignition source for main burners ACTUATOR Admits gas to burner when depres sed.
This appliance is intended for use in commercial establishments only. This appliance is intended to prepare food for human consumpti on. No other use is recommended or autho rized by the manufacturer or its agents. This hotplate must be installed by a technician qualifie d and certifie d or licensed to install gas-fired equipme nt.
INSTALLATION NOTE: DO NOT discard the carton or other packing materials until you have inspected the appliance for hidden damage and tested it for proper operation. Refer to SHIPPING DAMAGE CLAIM PROCEDURE on the inside front cover of this manual. DANGER: HEALTH HAZARD This appliance must be properly ventilated.
INSTALLATION (continued) GAS APPLIANCE CODE COMPLIANCE The installation of gas piping from the outlet side of the ga s meter or service regulator to the hotplate must be performed by a technician qualified and certified or licensed to install gas-fire d e quipment.
INSTALLATION (continued) INSTALLING THE HOTPLATE Refer to the nameplate. Verify the fuel type and pressure, which must match the nameplate specifications. Conne cting the hotplate to the wrong fuel type and/or pressure will compromise the safety and/or performance of the appliance.
INITIAL ADJUSTMENT SET GAS PRESSURE: Turn the gas shut-off valve OFF . A gas pressure test tap is provided on the gas suppl y manifold. Remove both burner control knobs and the front pan el. Remove plug in gas pressure test tap and attach a manometer.
OPERATION GENERAL OPERATIONAL NOTES Carefully read the description of the hotplate operation on the specification sheet. Do NOT use this appliance if it has been subm erged in water. Call a qualified technician to examine the applia nce and to service or replace any component whi c h has been subme r ged.
WARNING: FIRE HAZARD NEVER attempt to force or repair a stuck control valve. Contact your Authorized Wells Service Agency for repair s. Forced or improperly repaired valves pose the ri sk of fire and/or explosion.
TROUBLESHOOTING 10 SYMPTOM POSSIBLE CAUSE SUGGESTED REMEDY Pilot will not light Gas supply off Check main / unit gas valves Air in lines Turn gas valve on.
CLEANING INSTRUCTIONS PREPARATION Turn gas shut-off valve OFF before clea ning. Allow hotplate to cool completely before cleani ng. FREQUENCY: Daily TOOLS Bristle Brush Clean Cloth or Sponge Mild Detergent Cleaner Formulated for Stainless Steel Warm Water CLEANING Turn gas shut-off valve OFF before clea ning.
CLEANING INSTRUCTIONS (continued) 12 Fig. 7 Hotplate Assembly FRONT BURNER Slides over RIGHT nozzle; hooks into FRONT slots on pilot support REAR BURNER Slides over LEFT nozzle; hooks into REAR slots on pilot support GRA TE ASSEMBL Y Sets in place above burners DRIP TRA Y Drops in place exposing tops of burners 1.
DESCRIPTION PART NO. CUST OMER SERVICE DA T A please have this information av ailable if calling for service RESTAURANT ___________ __________________ LOCAT ION _____________ INSTALLATION DATE _______.
Genuine Parts Protect - YOU - All - Ways SER VICE TRAINING - QUALITY SER VICE SER VICE TRAINING - QUALITY SERVICE CUSTOMER SA TISF ACTION CUSTOMER SA TISF ACTION Commercial Food Equipment Service Asso.
An important point after buying a device Wells H-2412G (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Wells H-2412G yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Wells H-2412G - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Wells H-2412G you will learn all the available features of the product, as well as information on its operation. The information that you get Wells H-2412G will certainly help you make a decision on the purchase.
If you already are a holder of Wells H-2412G, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Wells H-2412G.
However, one of the most important roles played by the user manual is to help in solving problems with Wells H-2412G. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Wells H-2412G along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
