Instruction/ maintenance manual of the product 9100/9400/9600 Wayne-Dalton
Go to page of 18
GARAGE DOORS & OPENERS Part No. IMPORT ANT NO TICES! Wayne-Dalton highly recommends that you read and fully under - stand the Installation Instructions and Owner’ s Manual before you attempt this installation. T o avoid possible injur y , read the enclosed instructions carefully before installing and operating the garage door .
2 Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.W ayne-Dalton.com A.
I m p o r t a n t S a f e t y I n s t r u c t i o n s Definition of key words used in this manual: W ARNING W ARNING INDICA TES A POTENTIALL Y HAZARDOUS SITUA TION WHICH; IF NOT AVOIDED , COULD RESUL T IN SEVERE OR FA T AL INJURY . CAUTION: PROPER TY DAMAGE OR INJURY CAN RESUL T FROM FAILURE TO FOLLOW INSTRUCTIONS.
5/16” x 1 5/8” Hex head lag screws (as required) 1/4”-20 x 11/16” Self drilling screws (as required) 1/4”-14 x 5/8” Self tapping screws (as required) (2) #12 x 1/2” Phillips head screws .
and flush with the inside edge of the jamb. T emporarily secure the weatherstrip with equally spaced nails. Repeat for other side. This will keep the bottom section from falling out of the opening during installation. Equally space nails approximately 12” to 18” apart.
INST ALLA TION Before installing your door , be certain that you have read and followed all of the instruc- tions covered in the pre-installation section of this manual. Failure to do so may result in an improperly installed door . NOTE: Reference TDS 160 for general garage door terminology at www.
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.W ayne-Dalton.com section until it is seated against bottom section.
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.W ayne-Dalton.com T op Section T ools: Hammer , Step ladder , T ape measure 14 Place the top section in the opening.
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.
Door Arm Hookup T ools: Needle nose pliers Align hole in the door arm with holes in drawbar operator bracket tabs, as shown. Insert 5/16” x 1-1/4” clevis pin, making sure hole in clevis pin is outside of second tab of drawbar operator bracket. Insert hairpin cotter into clevis pin hole and spread hairpin cotter to secure assembly , as shown.
Second section 1/8” Inside lock End cap (4) 1/4”-20 x 11/16” Self drilling screws Square hole in vertical track Pull Down Rope T ools: Power drill, 1/8” Drill bit, T ape measure W ARNING W ARNING DO NOT INST ALL PULL DOWN ROPE ON DOORS WITH OPERA TORS.
Cleaning Y our Garage Door IMPORT ANT : DO NOT USE A PRESSURE W ASHER ON YOUR GARAGE DOOR! While factory-applied finishes on garage doors are durable, it is desirable to clean them on a routine basis. Some discoloration of the finish may occur when a door has been exposed to dirt-laden atmosphere for a period of time.
Lifetime Limited Warranty Models 9100, 9400, 9600 Subject to the terms and conditions contained in this Lifetime Limited Warranty , Wayne-Dalton, A Division Of Overhead Door Corporation (“Manufactur.
.
AFTER INST ALLA TION IS COMPLETE, F ASTEN THIS MANUAL NEAR THE GARAGE DOOR. Please Do Not Return This Product T o The Store Thank you for your pur chase. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pa ges business listings or go to the Find a Dealer section online at www .
An important point after buying a device Wayne-Dalton 9100/9400/9600 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Wayne-Dalton 9100/9400/9600 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Wayne-Dalton 9100/9400/9600 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Wayne-Dalton 9100/9400/9600 you will learn all the available features of the product, as well as information on its operation. The information that you get Wayne-Dalton 9100/9400/9600 will certainly help you make a decision on the purchase.
If you already are a holder of Wayne-Dalton 9100/9400/9600, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Wayne-Dalton 9100/9400/9600.
However, one of the most important roles played by the user manual is to help in solving problems with Wayne-Dalton 9100/9400/9600. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Wayne-Dalton 9100/9400/9600 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
