Instruction/ maintenance manual of the product VGL60 Vulcan-Hart
Go to page of 12
VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201-0696, TEL. (502) 778-2791 FORM 30909 (1-95) VGL SERIES GAS STEAM KETTLES MODEL VGL20 VGL40 VGL60 VGL20E VGL40E VGL60E INST ALLA TION & OPERA.
– 2 – IMPORT ANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED.
– 3 – Installation, Operation, and Care of VGL SERIES GAS STEAM KETTLES SA VE THESE INSTRUCTIONS FOR FUTURE USE GENERAL The VGL Series Gas Steam Kettles use efficient gas heat and thermostat controls to provide superior cooking performance. The VGL Kettles are intended for commercial use only; not for household use.
– 4 – LEVELING THE APPLIANCE To level the kettle, use a spirit level in all directions on the top of the kettle with the lid up. Units with legs — adjust the bottom foot in each leg to overcome an uneven floor.
– 5 – GAS CONNECTION The data plate on the lower right side of the kettle indicates the type of gas your unit is equipped to burn. DO NOT connect to any other gas type. A 1" NPT line is provided at the rear for the connection. Each kettle is equipped with an internal pressure regulator which is set for 4" W.
– 6 – ELECTRICAL CONNECTION Refer to the electrical diagram attached to the inside of the front panel and to ELECTRICAL DATA. ELECTRICAL DATA MODEL Volts / Hz / Ph Standard / Optional Amps Circuit Requirement VGL Series 115 / 60 / 1 Standard 2.0 15 Amp Cord/Plug 208 / 60 / 1 or 3 Optional 1.
– 7 – USING THE GAS CONTROL (Kettles with Pilot Lights) A. Lighting 1. Turn thermostat to lowest position and turn the power switch OFF. 2. Open control panel access door. 3. Turn dial on combination control to pilot position. NOTE : Any gas service valves exterior to the unit should be open.
– 8 – USING THE GAS CONTROL (Kettles with Electronic Ignition) Units equipped with electronic ignition do not require "lighting" the pilot with a match. A. Lighting 1. Turn thermostat to lowest position and turn the power switch OFF. 2. Open control panel access door.
– 9 – ON OFF POWER COOKING LOW WATER COOK TEMP. ▼ OFF PRESSURE WATER LEVEL OPERA TION WARNING : THE STEAM KETTLE AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANING, AND SERVICING THE STEAM KETTLE. CONTROLS (Figs. 1, 2) Main Power Switch — Turns main power ON or OFF.
– 10 – DAILY OPERATION Daily operation should consist of turning on the power switch and setting the thermostat for the desired temperature. It is recommenced the kettle be preheated empty prior to use. Milk or egg based products should be placed in the kettle before heating, however, to prevent sticking.
– 11 – CLEANING WARNING : DISCONNECT ELECTRICAL POWER BEFORE CLEANING. Clean inside the kettle daily by wiping with a clean damp cloth. Clean the exterior daily with soap and detergent and water. Rinse thoroughly and wipe dry with a soft clean cloth.
– 12 – FORM 30909 (1-95) PRINTED IN U.S.A..
An important point after buying a device Vulcan-Hart VGL60 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vulcan-Hart VGL60 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vulcan-Hart VGL60 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vulcan-Hart VGL60 you will learn all the available features of the product, as well as information on its operation. The information that you get Vulcan-Hart VGL60 will certainly help you make a decision on the purchase.
If you already are a holder of Vulcan-Hart VGL60, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vulcan-Hart VGL60.
However, one of the most important roles played by the user manual is to help in solving problems with Vulcan-Hart VGL60. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vulcan-Hart VGL60 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
