Instruction/ maintenance manual of the product ML-136095 Vulcan-Hart
Go to page of 20
INS T ALL A TION & OPER A TION MANU AL GAS 2/3 JACKETE D S TA TIO NAR Y AND TI L TING KETTLES MODELS K20GL ML - 136090 K40GL ML - 136091 K60GL ML - 136092 K20G L T ML - 136094 K40G L T ML - 136095.
G AS K ETTLES — 2 — IMPORT AN T FOR YOUR SAFETY THIS M AN U AL H AS BEEN PRE P AR E D FOR PERSONNEL Q UALIFIED T O INS T ALL GA S EQUIPMEN T , WH O SHOUL D PERFOR M TH E I NITI A L FIE L D ST AR T -U P AND A DJUSTMENTS OF THE EQUIPM ENT CO VERE D BY THIS M AN U AL .
G AS K ETTLES — 3 — CONTENT S GENERAL ................... .......... ............... .......... ............... .......... ............... ............... .......... ............... .... . 4 INS T ALL A TION ..................... .......... ......
G AS K ETTLES — 4 — INS T A LLA T ION , OPER A TION AND MAINTE NANCE OF KGL A ND KG L T SERIES GAS KETTLES SA VE THESE INSTRUCTIONS FOR FUTURE USE GENERAL V ulcan gas 2/3 jack eted kettles are produced wit h qualit y workmanship and mat erial. Proper installation, usage and maintenance will result in many y ears of satis factory performance.
G AS K ETTLES — 5 — INS T ALL A TIO N UN P A CKING This k ettle wa s inspec ted bef ore leaving the factor y . The transportation company assumes full responsibility for safe deliv er y upon acceptance of the shipment. Immediately aft er unpac king, check for possibl e shippi ng da mag e.
G AS K ETTLES — 6 — G AS CONNECTIONS Gas supply connections and any pipe joint compound must be res istant to the action of propane gases. Codes require that a gas shuto f f valve be installe d in the gas line ahead o f the ke ttle. Connect the gas s upply line to the gas val ve on t he kettle.
G AS K ETTLES — 7 — Gas Connection Data FLEXIBLE G AS CONNEC T ORS BTU/h r . FLO W CA P AC I T Y 1, 2 LEN GTH 3 L ENG TH 3 End Fittings - ( 1) Q ui ck Disconnect & (1) Threade d End Fittings -.
G AS K ETTLES — 8 — G AS AN D A L TITUDE CONVERSI ON The kettle can be f ield converted to propane gas or for operat ion at altitudes above 2 000f t elevation . A manomet e r tha t r ead s in 1/100 " W C an d port abl e comb usti o n analyze r ar e req uire d.
— 9 — G AS K ETTLES A lti tude: 1. Remove the right side controls compartment side panel. 2. Locate the gas combination valv e located in the bottom of the controls compartment. 3. T urn S2 screw (Fi g. 1) (using 5/64” Allen wrench), ½ turn cl ock w ise 4.
— 10 — G AS K ETTLES LOC A TION Position the ke ttle in it s final locat ion. Check tha t there are s uff ic ie nt clearanc es for operating and servicing the k et tl e, and f or proper clearance of t he cover when raised. Keep the ke ttle f ree and clear from all combustible substances.
— 11 — G AS K ETTLES T ilting Kett le "Q" "P" "E" "F" "M" ADD 2" FOR PLUG VALVE "L" "K" "B" "N" "A" 12.0 [305] 9.3 [235] 4.1 [104] ELEC SHOW N W ITH OPTIONAL DRA W - OFF VALVE ( 2" PLUG VALVE) "R" 17.
— 12 — G AS K ETTLES the kettle. OPERA TION The kettle and its parts are hot. Use care w hen operat ing, cleaning or serv icing CONTROLS AND INDIC A T ORS Contro l Functio n V acuum/Pr essure Gaug e Indicates t he vacuum (in inches) and pr essure (in PSI) inside the kettle jacket.
— 13 — G AS K ETTLES BEFORE OPER A TION 1. Check G aug e Pressu re – should read 20 - 30 In . Hg . below zero wh e n cold. ( Higher r eadin g indicates air in jacket. See V enting instructions.) 2. Check to make sure gas supply valve is turned on.
— 14 — G AS K ETTLES VENTING W hile the kettle is cold, check the vacuum/pressure gauge. The ga uge sho uld be in the v acuum zone measuring between 20 to 30 in. Hg (84 to 100kPa). If n ot, t her e is air in the j ack et and it m ust be removed by venting f or pr oper heating.
— 15 — G AS K ETTLES ST A INLESS ST EEL EQUIPMENT C AR E A N D CLE A NING (Supplied courtesy of NAF EM. For more i nformatio n, vi sit their w eb site at ww w .nafem.org) Contrary to popular belief, sta inless steels A R E suscepti ble to rusting.
— 16 — G AS K ETTLES 4. T reat your w at e r . Though this is not always pr actical, sof te ni ng hard water can do much to reduce deposits. T here are certain f ilters th at can be installed to remove distasteful and corrosive elements. T o insure proper water treatment, call a treatment specialist.
— 17 — G AS K ETTLES CLE A NING The kettle and its parts are hot. Use care w hen operat ing, cleaning or serv icing the kettle. Disconnect the electrical po w er to the machine and fo llo w lockout / t agout procedure, before cleaning or servicing.
— 18 — G AS K ETTLES PLUG V A L VE CL EANING INSTRUCTIO NS Daily A fter Use Remove draw -of f valve plug for cleaning (Fig. 3). 1. Unscrew the retaining ring and remove it and the bottom w ashe r . 2. Pull t he va lve plug s tr aig ht up to remove from valve bod y .
— 19 — G AS K ETTLES M AI N T E N AN C E The kettle and its parts are hot. Use care w hen operat ing, cleaning or serv icing the kettle. VENTING W hen c old, the pressure gauge vacuum measuring z one should be between 20 to 30 I n. Hg (84 t o 100kPa).
G AS K ETTLES F- 35461 ( June 2012) — 20 — PRINTED IN U.S. A. TROUBLE SHOOTI NG Prob lem Possible Causes / Sug gested Co rr ect i ve A cti on W ill Not T urn On, no pow er light Kett le is not plugged i n / Plug in power cord. Power switc h is o ff / T urn on power sw itch.
An important point after buying a device Vulcan-Hart ML-136095 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vulcan-Hart ML-136095 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vulcan-Hart ML-136095 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vulcan-Hart ML-136095 you will learn all the available features of the product, as well as information on its operation. The information that you get Vulcan-Hart ML-136095 will certainly help you make a decision on the purchase.
If you already are a holder of Vulcan-Hart ML-136095, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vulcan-Hart ML-136095.
However, one of the most important roles played by the user manual is to help in solving problems with Vulcan-Hart ML-136095. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vulcan-Hart ML-136095 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
