Instruction/ maintenance manual of the product K20DL Vulcan-Hart
Go to page of 16
INST ALLA TION & OPERA TION MANUAL FORM 35459 (May 201 1) DIRECT STEAM 2/3 JACKETED ST A TIONAR Y AND TIL TING KETTLES MODELS K20DL ML-136081 K40DL ML-136082 K60DL ML-136083 K20DL T ML-136086 K40D.
IMPORT ANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREP ARED FOR PERSONNEL QUALIFIED TO INST ALL PLUMBING AND MUST BE ABLE TO PERFORM THE INITIAL FIELD ST ART -UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death.
— 3 — DIRECT STEAM KETTLES CONTENTS GENERAL ....................................................................................................................... ....................4 INST ALLA TION ..............................................
— 4 — DIRECT STEAM KETTLES INST ALLA TION, OPERA TION AND MAINTENANCE OF KDL AND KDL T SERIES DIRECT STEAM KETTLES SA VE THESE INSTRUCTIONS FOR FUTURE USE GENERAL V ulcan direct steam 2/3 jacketed kettles are produced with quality workmanship and material.
— 5 — DIRECT STEAM KETTLES INST ALLA TION UNP ACKING This kettle was inspected before leaving the factory . The transportation company assumes full responsibility for safe delivery upon acceptance of the shipment. Immediately after unpacking, check for possible shipping damage.
— 6 — DIRECT STEAM KETTLES LOCA TION Plumbing connections must comply with applicable sanitary , safety and plumbing codes. Stationary Kettle Position the kettle in its fi nal location. Check that there are suf fi cient clearances for operating and servicing the kettle, and proper clearance of the cover when raised.
— 7 — DIRECT STEAM KETTLES Tilting Kettle Position the kettle in its fi nal installed location to provide drainage directly below pour path, with suf fi cient rear clearance from the wall to allow the kettle to tilt completely without obstruction.
— 8 — DIRECT STEAM KETTLES INST ALLA TION PROCEDURE Make sure the kettle is in its fi nal location before performing the installation procedure. It may be necessary to increase the height of the kettle when leveling to clear the draw-off valve on tilting kettles.
— 9 — DIRECT STEAM KETTLES Maximum Flow Rate of Dry Steam in Pounds per Hour Supply Pressure Standard Pipe Size 1 / 2 " 3 / 4 "1 " 1 1 / 4 "1 1 / 2 "2 " 5 PSIG 20 40 .
— 10 — DIRECT STEAM KETTLES OPERA TION The kettle and its parts are hot. Use care when operating, cleaning or servicing the kettle. Food products with milk or egg base should be placed into a cold kettle before cooking. A void sudden contact of these food products to a hot kettle surface because they stick to the surface.
— 1 1 — DIRECT STEAM KETTLES ST AINLESS STEEL EQUIPMENT CARE AND CLEANING (Supplied courtesy of NAFEM. For more information, visit their web site at www .nafem.org) Contrary to popular belief, stainless steels ARE susceptible to rusting. Corrosion on metals is everywhere.
— 12 — DIRECT STEAM KETTLES 4. T reat your water . Though this is not always practical, softening hard water can do much to reduce deposits. There are certain fi lters that can be installed to remove distasteful and corrosive elements. T o insure proper water treatment, call a treatment specialist.
— 13 — DIRECT STEAM KETTLES CLEANING The kettle and its parts are hot. Use care when operating, cleaning or servicing the kettle. The kettle interior and exterior should be thoroughly washed after each use when a different food is to be cooked next or when cooking is completed for the day .
— 14 — DIRECT STEAM KETTLES PLUG V AL VE CLEANING INSTRUCTIONS Daily After Use Remove draw-off valve plug for cleaning (Fig. 4). 1. Unscrew the retaining ring and remove it and the bottom washer . 2. Pull the valve plug straight up to remove from valve body .
— 15 — DIRECT STEAM KETTLES MAINTENANCE SERVICE T o obtain service and parts information concerning this unit, contact the V ulcan-Hart Service Agency in your area (refer to listing supplied with the kettle), or contact the V ulcan-Hart Service Department at the address or phone number shown on the front cover of this manual.
— 16 — DIRECT STEAM KETTLES F-35459 (May 201 1) PRINTED IN U.S.A..
An important point after buying a device Vulcan-Hart K20DL (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vulcan-Hart K20DL yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vulcan-Hart K20DL - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vulcan-Hart K20DL you will learn all the available features of the product, as well as information on its operation. The information that you get Vulcan-Hart K20DL will certainly help you make a decision on the purchase.
If you already are a holder of Vulcan-Hart K20DL, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vulcan-Hart K20DL.
However, one of the most important roles played by the user manual is to help in solving problems with Vulcan-Hart K20DL. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vulcan-Hart K20DL along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
