Instruction/ maintenance manual of the product GS60E ML-52660 Vulcan-Hart
Go to page of 12
GS, GL & GT SERIES FULL Y STEAM JACKETED GAS KETTLES MODEL GS25E ML-52633 GS30E ML-52634 GL40E ML-52635 GS60E ML-52660 GL80E ML-52637 GT100E ML-52638 GT125E ML-52639 GT150E ML-52640 VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201-0696, TEL.
– 2 – IMPORT ANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED.
– 3 – T ABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
– 4 – Installation, Operation and Care of GS, GL & GT SERIES FULL Y STEAM JACKETED GAS KETTLES KEEP THESE INSTRUCTIONS FOR FUTURE USE GENERAL Your Vulcan steam jacketed kettle is produced with quality workmanship and material. Proper installation, usage and maintenance will result in many years of satisfactory performance.
– 5 – INSTALLATION CODES AND STANDARDS In the United States, Vulcan kettles must be installed in accordance with state and local codes, with the National Fuel Gas Code, (ANSI-Z223.1, latest edition) available from the American Gas Association, 1515 Wilson Boulevard, Arlington, VA 22209, with the National Electrical Code (ANSI/NFPA No.
– 6 – FAUCET BRACKET A bracket is provided for mounting a faucet on the kettle; this would allow the addition of water to the kettle for the convenience of the food preparer. A faucet is available as an accessory. NOTE: Do not use tap water from faucet to fill kettle jacket.
– 7 – OPERA TION WARNING : THE KETTLE AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANING AND SERVICING THE KETTLE. Before operating, check the jacket water level by looking at the sight glass at the rear of the kettle with both upper and lower valves open.
– 8 – CONTROLS — KETTLES WITH ELECTRONIC IGNITION (Prior Construction, Fig. 2) Thermostat — Controls heat in the kettle. High dial settings are for cooking; low settings are for holding. On – Off Switch — Located on the upper right-hand corner of the control panel.
– 9 – Fig. 4 Low Water Cutoff — Pilot and Main Burner won't operate if water level in jacket is low. Pressure Relief Valve — Protect the kettle against excessive pressure should the thermo- Pressure Limit Switch stat malfunction.
– 10 – TURNING ON A KETTLE EQUIPPED WITH ELECTRONIC IGNITION (Applies to Fig. 1 or Fig. 2) Before lighting the pilot, both the burner and pilot must have been off at least 5 minutes. 1. Remove the control panel cover screw. 2. Remove the control box cover (lift, pull out at bottom, lower).
– 11 – CLEANING After each use, clean and flush the kettle liner immediately, especially if the product cooked contained salt, vinegar or acid in any concentration. Do not use chlorine based cleaning products. Do not use metalic scouring pads or brushes.
– 12 – MAINTENANCE WARNING : THE KETTLE AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANING AND SERVICING THE KETTLE. WARNING : DISCONNECT THE ELECTRICAL POWER TO THE MACHINE AND FOLLOW LOCKOUT / TAGOUT PROCEDURE. PRESSURE RELIEF VALVE Open the pressure relief valve at least once a day to avoid lime build-up.
An important point after buying a device Vulcan-Hart GS60E ML-52660 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vulcan-Hart GS60E ML-52660 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vulcan-Hart GS60E ML-52660 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vulcan-Hart GS60E ML-52660 you will learn all the available features of the product, as well as information on its operation. The information that you get Vulcan-Hart GS60E ML-52660 will certainly help you make a decision on the purchase.
If you already are a holder of Vulcan-Hart GS60E ML-52660, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vulcan-Hart GS60E ML-52660.
However, one of the most important roles played by the user manual is to help in solving problems with Vulcan-Hart GS60E ML-52660. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vulcan-Hart GS60E ML-52660 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
