Instruction/ maintenance manual of the product GCT72 Vulcan-Hart
Go to page of 16
INSTALLATION & OPERATION MANUAL VULCAN ENDURANCE Series Gas Hot Plates MODELS: GCT12 GCT2 4 GCT36 GCT4 8 GCT60 GCT7 2 www.vulcanhart.com ITW Food Equipment Group, LLC 10405 Westlake Drive Charlotte, NC 28273 RETAIN THIS MANUAL FOR FUTURE USE FORM F38202 Rev .
IMPORTANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSO NNEL QUALIFIED TO INSTALL GA S EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. POST IN A PROMINENT LOCATION THE IN STRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED.
- 3 - INSTALLATION, OPERATION AND CARE OF VULCAN ENDURANCE SERIES GAS HOT PLATES PLEASE KEEP THIS MANUAL FOR FUTURE USE GENERAL Vulcan hot plates are produced with quality workmanship and material. These hot plates are designed with efficiency in cooking performance, sanitation, and ea se of cleaning in mind.
- 4 - The hot plate(s) must be installed so that the flow of combustion and ventilation air will not be obstructed. Adequate clearance for air openings into the hot plate(s) must be provided. Make sure there is an adequate supply of air in the room to allow for combustion of the gas at th e burners.
LEVELING To level the hot plate, place a carpenter's level on the hot plate and check leveling of the unit side to side and front to rear. Achieve leveling by turning each foot section of the unit's leg as needed. Turning the foot in a counter clockwise directi on will increase height and clockwis e will decrease.
gases be ventilated to the outside of the building through a ventilation system installed by qualified personnel. From the termination of the flue to the filters of the hood venting system, a minimum clearance of 18" (457 mm) must be maintained.
- 7 - Vulcan equipment is strongly constructed and is designed to give you long, satisfactory service at low cost, provided you give it proper care. Frequent cleaning and occasional adjusting should reward you with low operating and maintenance costs and faster, better service.
- 8 - calling for service, the following information must be available: model number, serial number, and gas type. This information can be found on the main data plate, located on the side of the unit. PRECAUTIONS When scraping off heavy deposits of grease or oil fr om stainless steel equipment, never use ordinary steel scrapers.
MODE D’INSTALLATION ET MODE D’EMPLOI PLAQUES CHAUFFANTES DE LA SÉRIE VULCAN ENDURANCE MODÈLES: GCT12 GCT24 GCT36 GCT48 GCT60 GCT72 www.vulcanhart.com Une division de Groupe ITW Équipement alimentaire, LLC 10405 Westlake Drive Charlotte, NC 28273 DOCUMENT À CO NSERVER EN CAS DE BESOIN F38202 Rév.
MESURES DE SÉCURITÉ IMPORTANTES CE MANUEL A ÉTÉ PRÉPARÉ À L ’INTENTION D’UN PERSONNEL QUALIFIÉ ET AUTORISÉ À INSTALLER DES APPAREILS FONCTIONNANT AU GAZ ET À EFFECTUER LE DÉMARRAGE INITIAL CHEZ LE CLIENT DE MÊME QUE LE RÉGLAGE DES APPAREILS CONCERNÉS DANS CE MANUEL.
- 3 - Installation, fonctionnement et entretien PLAQUES CHAUFFANTES DE LA SÉRIE VULCAN ENDURANCE GÉNÉRALITÊS Les plaques chauffantes Vulcan sont fabriqués avec le plus grand so in et à partir des meilleurs matériaux.
- 4 - Les plaques chauffantes doivent se trouver dans un endroit suffisamment espacé pour permettre leur entretien et leur fonctionnement appropriés.
NIVELAGE Pour niveler la plaque chauffante, déposer un niveau de menuisier sur la surface de la plaque chauffante et procéder à son nivelage d’un côté à l’autre et d’avant vers l’arrière. Terminer le nivelage en tournant chaque section de pattes si nécessaire.
FONCTIONNEMENT La plaque chauffante et ses composants sont chauds. Exercer une extrême prudence lors de son utilisation, nettoyage ou entretien. COMMANDES Robinet de brûleur de surface de cuisson – Permet d’acheminer le gaz vers les brûleurs de la surface de cuisson.
- 7 - remettre en place sur la plaque chauffante), enduire les grilles d’une mince couche d’huile végétale ou vaporiser de l’huile à cuisson. Remettre les grilles en place après leur apprêtage.
- 8 - PRÉCAUTIONS Ne jamais utiliser une racle ordinaire en acier inoxydable pour enlever les dépôts tenaces de graisse ou d’huile sur une surface en acier inoxydable.
An important point after buying a device Vulcan-Hart GCT72 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vulcan-Hart GCT72 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vulcan-Hart GCT72 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vulcan-Hart GCT72 you will learn all the available features of the product, as well as information on its operation. The information that you get Vulcan-Hart GCT72 will certainly help you make a decision on the purchase.
If you already are a holder of Vulcan-Hart GCT72, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vulcan-Hart GCT72.
However, one of the most important roles played by the user manual is to help in solving problems with Vulcan-Hart GCT72. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vulcan-Hart GCT72 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
