Instruction/ maintenance manual of the product ECO4S ML-52501 Vulcan-Hart
Go to page of 20
ECO4D FORM 30932 Rev. C (2-99) MODEL ECO4S ML-52501 ECO4D ML-52502 ECO4C ML-52503 ECO6D ML-52504 ECO6C ML-52505 ECO SERIES ELECTRIC CONVECTION OVENS INST ALLA TION & OPERA TION MANUAL VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201-0696, TEL.
– 2 – T ABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . .
– 3 – Installation, Operation And Care Of ECO SERIES ELECTRIC CONVECTION OVENS KEEP THESE INSTRUCTIONS FOR FUTURE USE Your Vulcan Electric Convection Oven is produced with quality workmanship and material. Proper installation, usage and maintenance of your oven will result in many years of satisfactory performance.
– 4 – INST ALLA TION UNPACKING Immediately after unpacking the oven, check for possible shipping damage. If this oven is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery.
– 5 – 3. Mount the oven on top of the stand or cabinet (Fig. 1). Assembling the Chimney and Flue Extension Remove the oven chimney and flue extension from the rear of the oven (motor compartment) and use the screws provided to fasten the chimney to the top rear of the oven.
– 6 – CASTERS If the oven is to be installed on casters, assemble the casters to the legs provided. Place the locking casters on the front legs and non-locking casters on the rear legs.
– 7 – Electrical Connections WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING: DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH TO INDICATE THAT YOU ARE WORKING ON THE CIRCUIT.
– 8 – PL-51827 O FF O N TURN GAS VALVE "ON" PUSH MASTER SWITCH TO "ON" POSTION. IF OVEN DISCONNECT SUPPLY BEFORE CHANGING FUSES, CLEANING OR ANY OTHER SERVICE 15 AMP CLASS G FU.
– 9 – 2-SPEED MOTOR — LO / HI — Adjusts air velocity in the oven. Use the HI setting as the usual operating speed and the LO setting for delicate product like meringue which might be blown around in the oven. FUSE HOLDERS — Replace fuses with appropriate type described on control panel.
– 10 – PL-51829 TURN GAS VALVE "ON" PUSH MASTER SWITCH TO "ON" POSTION. IF OVEN DISCONNECT SUPPLY BEFORE CHANGING FUSES, CLEANING OR ANY OTHER SERVICE 15 AMP CLASS G FUSES WARN.
– 11 – Temperature Knob (When Not Timing Product) 1. Sets the roast temperature when the Roast Button light is lit. The Roast Button light can be turned on by pressing the Roast Button. 2. Sets the hold temperature when the Hold Button light is lit.
– 12 – Thermometer Button When pressed, causes actual cavity temperature to display for about 8 seconds, then display returns to set temperature. Heat Light When lit, indicates that power is being supplied to the heating elements. Ready Light Will be lit any time the actual temperature is within +/- 5 ° F (+/- 2.
– 13 – Gentle Bake Button Selects the gentle bake time setting. A roast time must be set first. The gentle bake time can then be set equal to or less than the roast time. The gentle bake time will be the portion of roast time to operate in the gentle bake mode.
– 14 – BEFORE FIRST USE Before using the oven for the first time, it must be "burned in" to release any odors that might result from heating the new surfaces in the chamber. 1. Using a clean damp cloth, wipe the inside of the oven, including the racks.
– 15 – Cooking 1. Open doors and load the product into the oven. Place pans in the center of the racks. Close doors. 2. Set Roast temperature and time. Set Hold temperature and Gentle Bake time, if desired. Gentle Bake time may not be more than roast time.
– 16 – 400 º F 300 º F 200 º F 100 º F ROAST AND HOLD DIAGRAM - Time vs. Temperature SHORT BEEP. TIMER DISPLAY FLASHES 00:00. ROAST THERMOSTAT OFF. HEATERS OFF UNTIL HOLD TEMPERATURE IS REACHED. LONG BEEP (20 SEC.) HEATERS MAINTAIN HOLD TEMPERATURE.
– 17 – COOKING GUIDELINES — MODELS ECO4S AND ECO4D/ECO6D OVENS PRODUCT TEMPERATURE TIME NUMBER OF RACKS ° F ( ° C) (MIN.) BREAD PRODUCTS Bread (24, 1-lb.
– 18 – TIMER SETTINGS FOR ROLLED BEEF ROASTS — MODEL ECO4C/ECO6C OVENS ROAST TEMPERATURE 200 ° F (93 ° C) 250 ° F (121 ° C) 300 ° F (149 ° C) HOLD TEMPERATURE 140 ° F (60 ° C) DONENESS R.
– 19 – POWER OUTAGE In case of a power outage, the oven will automatically shut down. When power is restored to the lines, the oven will resume its normal operation. However, if the oven is to be left unattended during a power outage, push the master switch to the OFF position.
– 20 – FORM 30932 Rev. C (2-99) PRINTED IN U.S.A. MAINTENANCE WARNING: TURN OVEN OFF AND UNPLUG POWER SUPPLY CORD BEFORE PERFORMING ANY MAINTENANCE. The fan motor comes with sealed bearings and requires no lubrication. Annually check the flue, when cool, to be sure it is free of obstructions.
An important point after buying a device Vulcan-Hart ECO4S ML-52501 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vulcan-Hart ECO4S ML-52501 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vulcan-Hart ECO4S ML-52501 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vulcan-Hart ECO4S ML-52501 you will learn all the available features of the product, as well as information on its operation. The information that you get Vulcan-Hart ECO4S ML-52501 will certainly help you make a decision on the purchase.
If you already are a holder of Vulcan-Hart ECO4S ML-52501, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vulcan-Hart ECO4S ML-52501.
However, one of the most important roles played by the user manual is to help in solving problems with Vulcan-Hart ECO4S ML-52501. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vulcan-Hart ECO4S ML-52501 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
