Instruction/ maintenance manual of the product XC70 (2005) Volvo
Go to page of 259
2005 V70, V70 R & X C70 VO L VO 2 0 0 5 TP 755 3 ( German ). A T 04 46 . P rinted in Sweden, Elanders Infologistics V äst AB, Mölnly c ke 2004 TP 7553 BETRIEBSANLEITUNG WE B ED IT IO N.
1 Contents An alphabetical index is at the back of the book. Page Safety 9 Instruments, switches and controls 29 Climate control 53 Interior 6 5 Locks and alarm 85 Starting, driving, gearshifting 95 W.
2 Main/Dipped beam ............ 40 Position/Parking lamps ...... 40 Fog lamps .......................... 40 Instrument lighting ............ 40 Beam length control ........... 4 0 H U - 4 0 3 DOLBYBNR SPORT COMFORT ADVANCED 8504954m Dashboard - left-hand drive Electronic climate control ECC .
3 DOLBYBNR H U - 4 0 3 ADVANCED COMFORT SPORT 8504955m Dashboard - right-hand drive Hazard warning flashers....45 Display ................................... 35 T achometer .............................. 30 Automatic gearbox ................. 30 Clock .
4 Interior - left-hand drive 8502691M Manual gearbox .................... 99 Automatic gearbox ............... 1 00 Handbrake ............................ 46 Switches in centre console ... 36 Folding down rear seat ............. 76 Folding down head restraint .
5 8502703m Interior - right hand drive Manual adjusting front seats ................... 66 Electrically adjusting front seats .............. 68 Seat heating .............................................. 4 5 Cleaning the upholstery ...................
6 8000256M Exterior Replacing front bulbs ................. 143 Sunroof ........................ 49 Cleaning the car body .............. 1 52 Rustproofing ............................ 150 T ouching up paintwork ............ 151 T yres ................
7 V olvo Cars and the environment Our environmental philosophy Quality, Safety and Environmental care are the three core values which guide all the activities of Volvo Cars. Volvo cars comply with strict international environmental standards and are manufactured in some of the cleanest and most resource-efficient plants in the world.
8 V olvo Cars and the environment 0000324 V olvo workshops and the environment Regular maintenance carried out by an authori- sed Volvo workshop creates the conditions for low fuel consumption and contributes to a cleaner environment.
9 Safety Seat belts 10 Airbags 12 Side impact air bags 15 Collision curtains 18 WHIPS 19 Brake system 21 Stability system 23 Child safety 24.
10 8801947d Seat belts Keep in mind the following: • Do not use clips or anything else that pre- vents the belt from lying correctly . • Ensure the belt is not twisted or caught on anything. • The lap belt should sit low - not over the abdomen. • Stretch the lap belt over the lap by pulling the diagonal shoulder belt as illustrated above.
11 Seat belts and belt tensioners Seat belts and belt tensioners Each seat belt is equipped with a belt tensioner . A small mechanism integrated in the inertia reel is triggered at the moment of impact and tightens the belt around the body to reduce the slack caused by soft clothes or the like.
12 Airbags (SRS) Airbag (SRS) on the driver ’ s side T o further increase interior safety , your car is equipped with an airbag (SRS*) to complement the three-point seat belt. The inflatable airbag is folded into the centre of the steering wheel. The steering wheel is marked SRS AIRBAG.
13 Airbag (SRS) W ARNING! Airbag (SRS) - passenger side • Never place a child in a child seat or on a booster cushion in the front seat if the air- bag (SRS) is activated*. • Never allow a child to stand or sit in front of the front passenger seat.
14 Airbags (SRS) SRS system, left-hand drive Airbag (SRS system) The system consists of a gas generator surrounded by the inflatable airbag. If there is a collision of sufficient severity , a sensor reacts by activating the gas generator igniter thereby inflating the airbag.
15 SIPS airbag The SIPS airbag system is an electronic system consisting of two main components: the side airbag and the sensors. The side airbags are mounted in the backrest frames of the front seats while the sensors are located inside the centre and rear pillars.
16 8803406m Activating/deactivating the front passenger airbag (SRS) (option) Indicator showing that the passenger airbag (SRS) is deactivated. Activating/deactivating The switch is located on the passenger end of the dashboard and is accessible when the passenger door is open.
17 Which position should the switch be set to? ON = Airbag (SRS) activated . With the switch in this position, anyone over never a child in a child seat or booster cushion.
18 IC system (Inflatable Curtain) Always use the safety belts! If there are rear seat passengers, make sure the outer head restraints are upright and that the centre head restraint is correctly adjusted for anyone sitting there. 8802260n 8802259m IC system (Inflatable Curtains) The IC system protects the head from blows against the car interior .
19 WHIPS (Whiplash Protection System) 8502213e WHIPS This system consists of energy absorbing backrests and specially developed head restraints in both front seats. WHIPS seat WHIPS is activated in event of a collision from behind, based on the collision angle, speed and nature of the colliding vehicle.
20 When do the airbags and curtain inflate? The SRS system senses the collision in the level of braking and the speed reduction caused by the collision. The sensor determines whether the collision is of the character and nature requiring airbag deployment.
21 Brake system/ABS/EBD If a brake circuit fails If a fault should occur in one of the circuits it is still possible to stop the car . Press the pedal hard once - not repeatedly . The brake pedal can be depressed further and feels a little softer than usual.
22 Brake system/ABS/EBD W ARNING! If both the BRAKE and ABS warning symbols are lit up there is a risk that the rear end will have a tendency to slide during heavy braking. If the level in the brake fluid reservoir is normal, drive carefully to the nearest authorised V olvo workshop to have the brake system checked.
23 Stability system When the stability system is in action, it may seem like the car does not respond normally to acceleration. This is because the system detects the amount of friction on the road surface and allows the different stability system functions to operate.
24 Children in the car Important tips! When using other child safety products available on the market it is important that the installation instructions are carefully read and closely followed.
25 Integrated booster cushion for outer seats (option) 1 3 2 8502798a Outer seat - raising 1. Pull the handle so that the booster cushion rises up. 2. Grasp the cushion in both hands and move it rearwards. 3. Press the cushion until it locks into place.
26 Isofix bracket system for child seats (option) , accessories W ARNING! If the integrated booster cushion has been exposed to heavy load, in a collision for example, the entire booster cushion, including the seat belt and screws, must be replaced.
27 Location of the child in the car W eight / Age Front seat, alternatives* Centre rear seat, alternatives Outer rear seats, alternatives <10 kg (0 - 9 months) 9 - 18 kg (9-36 months) 15 - 36 kg (3-12 years) 1. Rear-facing child seat, secured with seatbelt.
28.
29 Instruments, switches and controls Combined instrument panel 30 Indicator and warning symbols 31 Messages in the display 35 Switches in the centre console 36 T rip computer 38 Cruise control 39 Hea.
30 Combined instrument panel 1. T emperature gauge Displays the engine cooling system tempera- ture. If the temperature is abnormally high and the needle enters the red field, a message is shown in the display .
31 Indicator and warning symbols W arning symbol in centre of dashboard This symbol shines as an yellow or red light depending on the severity of the fault discov- ered. See next page for more information! The indicator and warning symbols light when the ignition key is turned to driving position (position II) before starting.
32 W ARNING! If both the BRAKE and ABS warning symbols are lit up there is a risk that the rear end will have a tendency to slide during heavy braking. If BRAKE and ABS warning symbols light up at the same time, there may be a problem in the brake force distribution.
33 Indicator and warning symbols The indicator and warning symbols light when the ignition key is turned to driving position (position II) before starting. This shows that the symbols are functioning. When the engine is started all the symbols go out.
34 Indicator and warning symbols The indicator and warning symbols light when the ignition key is turned to driving position (position II) before starting. This shows that the symbols are functioning. When the engine is started all the symbols go out.
35 Messages in the display A 3 Messages in the display Whenever a warning or indicator symbol lights up, a message is displayed. When you have read and understood, press the READ button (A). Read messages are then erased from the display and are put into the memory .
36 The STC/DSTC system* This button is used to reduce or reactivate the functions in the STC/DSTC system. When the LED in the button comes on, the STC/DSTC system is activated (if no fault arises). In order to reduce the effect of the STC/DSTC system for reasons of safety the button must be held in for at least a half second.
37 3603551m 3603550m Switches in the centre console and dashboard Deactivating the deadlock function and detectors Use this button if you wish to shut off the deadlock function (deadlock means that the doors cannot be opened from the inside when they are locked).
38 T rip computer Controls - trip computer In order to access the trip computer information turn the ring (B) in steps, either forwards or backwards. By turning again you return to the starting point. A verage speed The average speed since the last reset ( RESET ).
39 Cruise Control (option) T emporary disengagement Press 0 to disengage the cruise control temporarily . CRUISE will be shown on the combined instrument panel.
40 Headlamps, Fog lamps, Beam length control, Instrument lighting D E A B C 3500824d A – Headlamps and position/ parking lamps All lighting off. Cars with daytime running lights: Ignition key in position II: Dipped beam lit (and front and rear position/parking lamps, numberplate lighting and instrument lighting).
41 W ARNING! Adjust the steering wheel before driving, never while driving. Ensure that the steering wheel is locked. Steering wheel adjustment The steering wheel can be adjusted both vertically and front-rear . Push down the control on the left-hand side of the steering column.
42 3601913d 3 1 2 1 2 Direction indicators, Follow-me-home Direction indicators, main/dipped beam switch and main beam flash 1 “Resistance point position” For turns requiring small steering adjustments (lane changing, overtaking) move the lever up or down and hold it with a finger .
43 Windscreen wipers/washer Rain sensor (option) The rain sensor automatically increases or decreases the speed of the windscreen wipers based on how much water it detects on the windscreen. The sensitivity of the rain sensor can be adjusted using the ring (1).
44 W iper/washer function - r ear window Rear window washer and wiper Move the lever forward to start the rear window washer . 1. Rear window wiper - intermittent wiping 2. Rear window wiper - normal speed Wiper - reversing If you put the car in reverse when the wind- screen wiper is engaged, the rear window wiper will be set to intermittent mode*.
45 Hazard warning flashers, Rear defroster , Heated seats Hazard warning flashers The hazard warning signal flashers (all direction indicator lamps flash) should be used when you are forced to stop or park the car where it is a hazard or hindrance to traffic.
46 Parking brake lever Parking brake, Electrical socket/cigarette lighter 64 68 72 76 80 64 68 72 76 80 3601943e Parking brake (handbrake) The lever is located between the front seats. The parking brake operates on the rear wheels. The warning symbol in the combined instrument panel lights when the brake is applied.
47 Power windows *When you have finished your trip and removed the ignition key , you can still close or open the windows as long as you have not opened either of the front doors . Switch to deactivate rear power windows The power window switches in the rear seat can be blocked from the switch on the driver ’ s door switch panel.
48 Rear-view mirrors 8301394M Rearview mirror A Normal position. B Dimming position. Use this if headlamps from the cars behind irritate you. Certain models have an autodim function, which means that dimming is automatic, based on current light conditions.
49 Sunroof Power sunroof (option) Sunroof controls are located in the headlining. The sunroof can be opened in two different ways: · Raise/lower trailing edge (ventilation position) · Rearwards/forwards (opening position/ comfort position*) The ignition key must be in position I or II.
50 Sun screen, Laminated front and rear side windows (option) Sun screen The sunroof also has an inner manually sliding sun screen. The sun screen slides back automatically when the sunroof is opened. 8301256d Pinch protection NOTE! The sunroof pinch protection function is activated if the hatch is blocked by an object.
51 Rearview mirror/door mirrors In certain weather conditions, the function of the dirt-repellent coating is improved if the door mirror defroster is used; see page 45. Defrost the door mirrors: · if they are covered with ice or snow · in heavy rain and dirty road conditions · if they are misted.
52.
53 Climate control Air distribution 54 Useful hints 55 Electronic Climate Control ECC 56 Manual climate control with air conditioning A/C 60 Fuel-driven parking heater 62.
54 Air distribution Air vents in the dashboard A Open B Closed C Directing airflow sideways D Directing airflow vertically · Aim the outer vents towards the side windows to remove misting. · In cold climates: close the centre vents for the most comfortable climate and best demisting.
55 Y our climate control system - useful hints Misting on window interiors A good way to reduce the problem of misting on the insides of the windscreen and other windows is to clean them. Use a normal window cleaner . Bear in mind that you must clean them more often if someone smokes in the car .
56 22 18 20 26 24 8704253d 20 18 22 24 26 MAN AUT Electronic Climate Control ECC Seat heater , right-hand side Defr oster , rear window and door mirr ors Defr oster , windscreen and side windows T emp.
57 Points to remember: · Make it a rule to have the air quality sensor activated at all times. · Recirculation is limited in cold climates to avoid misting. · In the event of misting, you should disconnect the air quality sensor . · In the event of the windows misting up you can also use the windscreen and side window defroster functions.
58 Electronic Climate Control ECC (option) AUTO The AUTO function regulates climate control so that the selected temperature is attained. The automatic function controls heating, air condition- ing, fan speed, recirculation and air distribution. If you select one or more functions manually , the other functions continue operating automatically .
59 8702776d AC - On/Off When the ON LED lights the air conditioning (A/C) system is controlled automatically by the system. In this way incoming air is cooled and moderately dehumidified. When AC OFF is selected and the OFF LED lights the air conditio- ning (A/C) system is always disconnected, other functions are still controlled automatically .
60 Manual climate control with air conditioning A/C 8702777d 8702831d Fan Fan speed can be increased or decreased by turning the knob. If the knob is set to 0, the air conditioning is disconnected. Recirculation Recirculation, together with your air conditioning (A/C) control, helps to cool a warm cabin more quickly .
61 Defroster - rear window and door mirrors Use this button to rapidly remove misting or ice from the rear window and the door mirrors. See page 45 for further informa- tion about this function.
62 Fuel-driven parking heater (option) A B C 3602296d General The electrical system must be ”awakened” before the parking heater can be programmed. This is most easily done by: · pressing the READ button or · pressing the main beam flash or · turning on the ignition.
63 Fuel-driven parking heater (option) Setting TIMER 1 and 2 For reasons of safety , you can only programme times for the following 24 hours, not several days in a row . 1. Use the ring (B) to toggle to TIMER 1. 2. Briefly press the RESET button (C) so that the hours setting starts to flash.
64.
65 Interior Seats 66 Interior lighting 69 Storage compartments 70 Rear seat and cargo area 75 Loading 80 Cargo net 81 Cargo area cover , Extra seat in cargo area 83 Spare wheel 84.
66 Front seats Seating position The driver ’ s and passenger seats can be adjusted to the optimum sitting and driving positions 1. Forward/rearward: lift the handle to adjust the distance to the steering wheel and pedals. Check that the seat is locked after changing position.
67 Folding the front passenger seat 8501727A Folding the front passenger seat The front passenger seat backrest can be folded to a horizontal position to make room for a long load. Fold the backrest as follows: · Move the seat as far back as possible.
68 Front seats Power seat (option) Preparations The seat is usually adjusted with the ignition key is in position I or II. It can also be adjusted within 4.
69 Interior lighting Rear reading lamps General lighting and fr ont reading lamps General lighting General lighting lights up and goes out when you press the button. General lighting comes on automatically and remains lit for 30 seconds: · When you unlock the car from the outside using the key or remote control.
70 W ARNING! Make sure that no hard, sharp or heavy objects lie on or in any of the storage compartments where they might cause injury during heavy braking. Always fasten large heavy objects with one of the seat belts. Ashtray (option) T o empty the ashtrays: Front seat: open the ashtray , pull out the insert.
71 1. Rear storage compartment (under armrest) The rear storage compartment of the centre console can be used to store CDs and the like. This storage compartment can be equipped with: - Privacy handset + holder (option) 2.
72 Extra handle XC70 Extra handle V olvo XC70 is equipped with an extra handle on the passenger side of the centre console storage compartment. This handle gives extra support when driving gravel roads, etc. W ARNING! The handle may become extremely warm if the car is parked in direct sunlight/warm temperatures.
73 Storage compartments, front Coat hanger The coat hanger is only intended for light garments. Cup holder (option) · Press on the holder to open it. · Press the holder back in place after use. NOTE! Never use glass bottles. Also bear in mind that hot beverages could scald you.
74 W aste bin, Collapsible table in rear seat 8802312m Bottle holder for rear seat passengers (option) Do as follows to use the bottle holder: 1. Open the holder . 2. Insert the bottle. The bottle holder can also serve as a waste bin. Insert a bag into the holder and fold it over the edges.
75 8503022m Centre seat head restraint (V70) Lower the centre seat head restraint if it is raised. Press the release button behind the right- hand support. See illustration. Rear seat and cargo area Centre seat head restraint (XC70) (Models with 3-portion rear seat) Raise : Pull the head restraint straight up.
76 B A 8503020m Tipping the backrest forwards Press the backrest catch to the rear and tip the backrest forwards. Folding the centre portion of the backrest (XC70) (Models with 3-portion rear seat) The left-hand and centre portions of the backrest can be folded individually .
77 Rear seat and cargo area W ARNING! (XC70 with 3-portion rear seat) · For reasons of safety , the centre seat backrest should never be left loose in the car . · If the centre seat backrest is removed, hard braking may cause unsecured objects in the cargo area to be thrown forward between the outer backrests.
78 Rear seat and cargo area 8503150m A - Catch in closed position B - Catch in open position Rear seat backrest position You can adjust the positions of the two rear seat backrests. T o adjust a backrest to the cargo position* : · Press the catch until the red mark is visible.
79 Cargo area 3903052m 8901657m Holder for grocery bags (option) Open the tailgate. Hang or secure your grocery bags by means of tensioning straps or holders. T o remove the plastic trough (option), turn the two knobs at the sides. Cargo area lighting An extra roof lamp is fitted at the end of the cargo area.
80 W ARNING! · Do not position heavy items right up against the front seats. The forward-folded backrest will then be pressed down unnecessarily hard. Never load above the level of the backrests. If you do, the cargo could be thrown forward during heavy braking or in a collision and seriously injure you or your passengers.
81 Cargo net 8503129m Protective grate XC70 For reasons of safety, the protective grate in the cargo compartment must always be fastened and secured correctly . Do the following to fit the protective grate: · Fold down the backrests. · Use a Torx screwdriver to press in and turn the knob (1) to red (to unlock).
82 Cargo net XC70 Nylon cargo net (Models with 3-portion rear seat) Volvo XC70 can be equipped with a cargo net made of strong nylon fabric, attachable to designated brackets in the roof headlining and tightened from eyelets on the floor*. The net can be fastened behind the upright backrests of the rear seats.
83 Cargo area cover , Extra seat in cargo area W ARNING! If your car is equipped with an extra seat, the tailgate must have a lock cylinder . The tailgate can now be unlocked from outside as normal (key in driver ’ s door and/or with remote control) as well as with the key in the tailgate lock.
84 7700566m Spare wheel Spare wheel Mounting Spare tyre, tools, jack - cars with bass speakers (option) The jack and tool kit are in a compartment above the spare wheel. Do the following to remove the spare wheel: · Remove the back floor hatch by unlocking it and pulling back 45°.
85 Locks and alarm Immobilizer , Remote control 86 Locking and unlocking 87 Replacing the battery in the remote control 88 When it is dark, Deadlocks 89 Child safety lock 90 Alarm 91.
86 Service key* For driver's door, ignition switch and steering wheel lock only . * certain markets only 8302187m Doors and locks Keys - Immobilizer Y our car is delivered with two master keys and one service key . One of the master keys is foldable and equipped with an integrated remote control.
87 Locking and unlocking Locking and unlocking the car from the outside All doors and the tailgate can be locked simultaneously from the outside using the master key or its remote control. In this mode, the door lock buttons and the interior door handles are disconnected.
88 Locking and unlocking Replacing the remote control battery If the locks repeatedly fail to react to signals from the remote control at a normal distance, the battery should be replaced at the next service interval or within the course of a couple of weeks.
89 When it is dark, deadlocks Deadlocks* Your car has a special deadlock position which means that the doors cannot be opened from the inside if they are locked. Deadlocks can only be activated from the outside by the driver ’ s door being locked with the key or remote control.
90 Contr ol for child safety lock - left rear door Child safety lock Contr ol for child safety lock - right rear door W ARNING! Remember that in the event of an accident, rear seat passengers cannot open the rear doors from the inside if the child safety locks are activated.
91 The alarm system (option) When the alarm is connected, it continually monitors all alarm points. The alarm is triggered if... · ...the bonnet is opened. · ...the tailgate is opened. · ...a side door is opened. · ...the ignition switch is turned with a non-approved key or subjected to force.
92 Alarm Status indicator lamp on the dashboard An indicator lamp (LED) at the top of the dashboard gives a description of the alarm system status: · Lamp not lit: alarm is deactivated. · The lamp flashes once every other second: the alarm is armed.
93 Alarm T esting the alarm system T esting the movement detector for the passenger compartment: 1. Open all windows. 2. Activate the alarm. Alarm activation is confirmed by the LED flashing slowly . 3. W ait 30 seconds. 4. T est movement detector in the passenger compartment by lifting a bag or similar from the seat.
94.
95 Starting, driving, gearshifting Fuel filler flap, Starting the engine 96 Economical driving 97 Starting the engine 98 Manual gearbox 99 Automatic gearbox 10 0 All Wheel Drive, Active chassis, FOUR-.
96 Fuel filler flap, Starting the engine Fuel filling The fuel cap is inside the fuel filler flap on the right rear wing. In high exterior temperatures there can be overpressure in the fuel tank. Open the filler cap slowly. Do not overfill the fuel tank.
97 Drive with anticipation Economical driving results from driving gently with anticipation and adapting your driving style and speed to the situation. Keep in mind the following: · Drive the engine to operating temperature as soon as possible! That is to say: do not let the engine idle, but drive with a light load as soon as you can.
98 Starting the engine Do not allow the engine and cooling system to overheat Under certain conditions, e.g. when driving in hilly terrain and with a heavy load, especially in warm weather, there is a risk of the engine and cooling system overheating.
99 Manual gearbox Gear positions, 5-speed Depress the clutch pedal fully with every gear change. Remove your foot from the clutch pedal between changes! Be sure to follow this shifting pattern. For the best possible fuel economy , use the highest gear possible as often as possible.
100 Gear selector positions Automatic gearbox N – Neutral position N is the neutral position. The engine can be started, but no gear is selected. Apply the parking brake when the car is stationary with the gear lever in N. D – Driving position D is the normal driving position.
101 Automatic gearbox 4302106d Mechanical gear selector inhibitor The gear selector can be moved freely between N and D . Other positions are locked with a latch that is released with the inhibitor button on the gear selector . Press the inhibitor button to move the lever forward or back between the different gear positions.
102 All-Wheel Drive (four-wheel drive) , Active chassis, FOUR-C All-Wheel Drive (A WD) (option) All-wheel drive is always engaged. All-wheel drive means that all four road wheels are driven at the same time. Power is automati- cally distributed between front and rear wheels.
103 Parking assistance (option) 3603495m 3602947r Parking assistance, fr ont and rear General Parking assistance is used as an aid to parking. A signal indicates the distance to an object. The frequency of the signal increases a you come closer to an object in front* of or behind the car .
104 3603503m Parking assistance Fault indicator The information symbol shines with a steady glow P ARK ASSIST SER VICE REQUIRED is shown in the information display in the centre of the combined instrument panel together with the symbol.
105 T owing – General information T owing eye, front T owing eye, rear A B C 8600422M If you need to be towed · Unlock the steering wheel lock so that the car can be steered.
106 W ARNING! Batteries can generate oxyhydrogen gas, which is highly explosive. One spark, which can be generated if you connect the jump leads incorrectly , is sufficient to make the battery explode. The battery contains sulphuric acid, which can cause serious burns.
107 Driving with braked trailer Driving with trailer · The towing bracket on the car must be of an approved type. Y our V olvo dealer can advise you as to which towing bracket to use.
108 Driving with braked trailer 0300202M Level control If you car is equipped with automatic levelling, the rear suspension always retains the correct ride height regardless of the load. When the car is stationary , the rear suspension sinks, which is completely normal.
109 T owing bracket IMG-201504 T owbars The towball must be cleaned and greased regularly . If a towball hitch with vibration damper is used, it is not necessary to grease the towball. If the car is equipped with a detachable towbar, follow the towball mounting instructions carefully .
110 8902085m A 8902084m T owing bracket Distance A above: Fixed tow hitch V70/V70 A WD: 1094 mm XC70: 1125 mm Max. ball pressure: 75 kg Attachment points under the car Distance B above: V70/V70 A WD: .
111 Detachable towbar – mounting the ball section IMG-20418 0 IMG-2041 8 8903789j Mounting the ball section 1. Remove the guard plug. 2. Ensure that the mechanism is in the unlocked position by turning the key clockwise. 3. Check that the indicator window (3) shows red.
112 IMG-2041 8 IMG-2041 8 IMG-20418 IMG-204191 4. Insert the towball section until there is an audible click. NOTE! The trailer ’ s safety cable must be connected to the attachment on the towbar . 5. Check that the indicator window shows green. 6. T urn the key anticlockwise to the locked position.
113 Detachable towbar – mounting the ball section IMG-2041 8 IMG-20418 8 IMG-20418 IMG-20419 0 1. Insert the key and turn it clockwise to the unlocked position. 2. Push in the locking wheel and turn it anticlockwise until there is an audible click. 3.
114 Load carrier cover Use the lug on the on the torque wrench (see illustration) or the ignition key to unscrew or secure the cover . T urn a quarter turn. 8901671d Roof loads – roof rails and the load carriers Fitting the load carriers Make sure that the load carrier is pressed firmly out against the roof rail.
115 Load carrier - Roof loads Loading General Load capacity is affected by extra accessories mounted on the car, such as a towbar, the load on the towball (75 kg with trailer hitched), load carriers and roof box, as well as the passengers’ combined weight.
116 Adjusting the headlamp beam pattern Correct beam pattern for left or right-hand traffic So as not to dazzle oncoming drivers, the headlamp beam pattern can be altered by masking the headlamps.
117 Masking templates for halogen headlamps, LHD variant Masking templates for halogen headlamps, RHD variant 5 8 3 4 7 6 3501781m 7 3501784m 5 1 8 6 2 Adjusting the headlamp beam pattern.
118 Adjusting the headlamp beam pattern Headlamp masking Copy the templates and transfer the pattern to a self-adhesive, waterproof material such as opaque tape or the like. The mask is positioned using the dot (5) in the headlamp lens as a reference point.
119 Masking templates for Bi-Xenon headlamps, LHD variant Masking templates for Bi-Xenon headlamps, RHD variant Adjusting the headlamp beam pattern.
120 1 - BLIS camera, 2 - Indicator lamp, 3 - BLIS symbol BLIS (Blind Spot Information System) BLIS BLIS is an information system which indicates whether there is another vehicle moving in the same direction in the "blind spot". The system is based on digital camera technolo- gy .
121 W ARNING! - BLIS does not work in sharp bends. - The system does not work if the camera lenses are covered. In this case the BLIS indicator lamps flash and a text message is shown in the display (see table on page 122). - BLIS does not work when the car is re- versing.
122 System status T ext in the display BLIS not functioning BLIND-SPOT SYST SER VICE REQUIRED Right-hand camera blocked BLIND-SPOT SYST R CAMERA BLOCKED Left-hand camera blocked BLIND-SPOT SYST L CAME.
123 Wheels and tyres General about wheels and tyres 12 4 T yre pressures 1 2 6 W ear , Spare wheel 1 27 Changing wheels 12 8 T emporary puncture repair and tools 1 3 0.
124 General New tyres Bear in mind that tyres are perishable goods - after a few years they begin to harden while their friction properties deteriorate little by little. Try to use fresh tyres when changing. This is especially important for winter tyres.
125 Winter tyres W e recommend winter tyres of dimension 195/65 R15 except for cars with turbo engines. 205/55 R16, 215/65 R16 (for XC70) and 225/45 R17 (for V70R) are recommended for these vehicles. Always use winter tyres on all four wheels! NOTE: Always consult your V olvo dealer as to which wheel and tyre type is appropriate for your car .
126 T yre pressures 7700242d Important Only V olvo-approved snow chains are permitted. Use of other snow chains could damage your car . Never drive faster than 50 km/h when snow chains are fitted! Never use ”quick links” because the space between the disc brakes and the wheels is too small.
127 Wheels and tyres T yres with tread wear indicators T read wear indicators are narrow , raised areas across the tread that have approximately 1.6 mm less tread depth than the remainder of the tyre (the letters TWI are on the side of the tyre). When this bar is visible, only 1.
128 Changing wheels Insert socket wrench and turn Pull the hub cap straight out (steel wheel rim) Remove wheel studs · Cars with steel rims have removable wheel covers. Prise off the wheel cover with a thick screwdriver or the like. If tools are not available, the wheel cover can be prised off by hand.
129 Changing wheels 7700245d 7700316m 7700244d Jack for cars with all-wheel drive (A WD and XC) The jack should be located so · Hold the jack against the pin in the jacking point as illustrated and wind down the jack foot so that it is pressed flat against the ground .
130 T emporary puncture repair and tools 1 Certain variants and markets General Cars which do not have a spare tyre are instead equipped with an emergency puncture repair kit. This kit can be used to both seal the puncture and to check and adjust the tyre pressure.
131 T emporary puncture repair and tools Inflating tyres Set up the warning triangle if a tyre must be inflated in an area where there is other traffic. · Ensure that the orange-coloured switch (2) is in position 0 and take out the cable (5) and air hose (4) from the side compartment (3).
132 T emporary puncture repair and tools Sealing punctured tyres Set up the warning triangle if an emergency tyre repair must be carried out in an area where there is other traffic.
133 · Check the tyre pressure again: NOTE! Do not open the orange-coloured part (7) when only the compressor will be used for inflating. 1) Connect the air hose (4) to the air valve on the tyre. 2) Connect the cable (5) to the 12 V socket. 3) Read the pressure on the compressor .
134 T emporary puncture repair and tools Replacing the sealant canister The sealant canister should be replaced before the expiration date has passed, see date decal (1), or after the tyre has been sealed. After use, the canister (6) with holder (8) and air hose (10) should be replaced.
135 T emporary puncture repair and tools · Check that the seal (7) on the new canister is not damaged. Screw the holder (9) onto the canister (6) and turn it anticlockwise until there is an audible click. · Refit the casing (3). Check that the casing is correctly mounted, screw it on with the screws (2).
136.
137 Fuses, bulb replacement Fuses 138 Replacing bulbs 14 3.
138 Fuses All electrical functions and components are protected with a number of fuses to protect your car ’ s electrical system from damage by short-circuits or overloads. Fuses are housed in four different locations in the car: 1. Integrated relay/fuse box in engine compart- ment.
139 3702167m 8 7 6 5 4 3 2 1 16 15 14 13 12 11 10 9 24 23 22 21 20 19 18 17 XXXXXX Fuse pliers Intact fuse Blown fuse A. Press in the catches on the rear of the box and pull the cover up A Relay/Fuse box in the engine compartment Fuse box in the engine compartment There are 24 fuse positions in the fuse box in the engine bay .
140 22 24 23 21 29 27 28 26 25 9 8 7 19 18 17 16 4 5 6 3 2 13 14 15 12 11 38 36 37 33 34 35 31 32 20 1 10 30 3701482D Fuse box in passanger compartment at dashboard end on driver ’ s side Located here are 38 fuse positions. The fuses are located inside the access panel on the end face of the dashboard.
141 3703457r 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Fuses in the passenger compartment within the sound barrier on the driver ’ s side This fuse box contains 36 fuse positions. The fuses are fitted inside the sound wall on the left- hand side.
142 Fuse box in cargo compartment N o Ampere rating 1. Reversing lamp ..................................... 10 2. Parking lamps, fog lamps, cargo compartment lighting, numberplate lighting, LEDs in brake lighting ........... 20 3. Accessories (AEM) ..
143 Replacing bulbs Replacing front bulbs All front bulbs (except fog lamps) are replaced via the engine compartment. W ARNING! On cars with Bi-Xenon headlamps, all work on the lamps should be carried out by an authorised V olvo workshop. Bi-Xenon headlights must be handled with extreme care due to the high-voltage unit.
144 Replacing bulbs Dipped beam T o remove the bulb: · Switch off all lights and turn the ignition key to position 0 . · Remove the cover . · Unplug the connector . · Disconnect the spring clamp. First push to the right so that the spring clamp discon- nects, then out and down.
145 Replacing bulbs Position and parking lamp T o remove the bulb: · Switch off all lights and turn the ignition key to position 0 . · Remove the cover (same cover as for dipped beam). · Pull out the bulb. · Unplug the connector . T o fit: · Fit the new bulb.
146 Replacing bulbs Side marker light · T urn the bulb holder clockwise and pull it out. · Replace the bulb. · Refit the bulb holder by turning it anticlock- wise. Fog lamp (option) T o remove the bulb: · Switch off all lights and turn the ignition key to position 0 .
147 3501707m Replacing bulbs Replacement of tail, position/ parking, and fog lamps in the rear · Switch off all lights and turn ignition key to position 0. · Open the access panel. · T wist the bulb holder anti-clockwise and remove it. · Press the bulb inwards, turn anti- clockwise and take out the bulb.
148 Replacing numberplate lighting bulb · Switch off all lights and turn ignition key to position 0! · Remove the screw with a screwdriver . · Loosen the whole lamp housing carefully and pull it out. · T urn the connector anticlockwise and pull out the bulb.
149 Car care and Service Rustproofing 1 50 Checking and repairing paintwork damage 15 1 W ashing 152 Service 155 Environmental care, Fuel consumption 15 7 Engine compartment 15 8 Diesel engine 15 9 Co.
150 Rustproofing - check and repair Rustproofing Y our V olvo received a very thorough and complete rustproofing at the factory . The body consists of galvanized sheet steel.
151 Repairing paintwork damage 8100503A Mask if necessary Paint Paint is an important part of the car’s rustproo- fing and should therefore be checked regularly .
152 W ARNING! After washing: always test the braking so that moisture and corro- sion do not affect the brake pads and impair the brakes! Depress the brake pedal lightly now and again when driving longer distances in the rain or slushy snow to warm up and dry the brake discs and pads.
153 W ashing Automatic car wash An automatic car wash is a simple and fast way of washing the car . Remember that an automatic car wash can never replace a proper handwash. The brushes of an automatic car wash do not fully reach all areas. During the first months of the car ’ s life it is recommended that you only handwash the car .
154 Cleaning door mirrors and front side windows with water-repellent coating (option) Never use products such as car wax, degreaser or similar on mirror/glass surfaces as this could ruin their water-repellent properties. Take care when cleaning so as not to damage the glass surface.
155 V olvo Service programme Before the car left the factory , it was thoroughly test driven. It was checked again in accordance with V olvo Car Corporation regulations before it was handed over to you.
156 V olvo Service 7700243d W ARNING! The car ignition system has very high voltage! The voltage in the ignition system is dangerous! Do not touch spark plugs, ignition cables or the ignition coil when the engine is running or the ignition is switched on! The ignition should be switched off when: · Conducting engine tests.
157 Bonnet, Engine compartment 8200092d 8200095d 1 2 3 4 5 6 7 8 9 10 7a 2000276m Opening the bonnet Pull the handle on the far left or right under the dashboard. Y ou hear when the lock releases. Insert your hand in the centre of the front edge of the bonnet and press up the safety catch handle.
158 Diesel Fuel system Diesel engines are very sensitive to contamination. Only use diesel fuel from a well-known oil company that fulfils the requirements for recom- mended fuel grade as described on page 174. Never use diesel of doubtful quality . The major oil companies can also of fer a special diesel fuel for winter use.
159 IMG-203460 Engine oil Checking and changing engine oil and filte r Certain engine variants have an engine oil decal on the bonnet. See page 166 for the location of the decal. The specification on the decal indicates what grade and viscosity the engine oil should have.
160 Checking and topping up coolant When topping up the coolant, follow the instructions on the packaging. It is important that the mixture of coolant concentrate and water is correct for the prevailing weather conditions. Never top up with water only .
161 Brake fluid, Power steering, Windscreen washer fluid Clutch and brake fluid reservoir The brake and clutch fluid have a common reservoir 1 . The fluid level must be between the MIN and MAX marks. Check the level regularly . Change the brake fluid every other year or at every other regular service.
162 Battery care · Check all battery cells. Use a screwdriver to remove the caps. Each cell has its own maximum level mark. · If necessary , top up with distilled water to the battery’ s maximum mark. · Never fill above the maximum mark (A). Important! Always use distilled or deionised water (battery water).
163 3100181 m Battery care W ARNING! Batteries can generate oxyhydrogen gas, which is highly explosive. One spark, which can be generated if you connect the jump leads incorrectly , is sufficient to make the battery explode. The battery also contains sulphuric acid, which can cause serious burns.
164 Replacing wiper blades 3602076D Replacement of headlamp wiper blade s 1 · Fold the wiper arm forward. · Pull the wiper blade outwards. · Press the new wiper blade into position. · Check that it is properly secured. Replacement of rear window wiper blades · Pull the wiper arm out away from the glass.
165 Specifications T ype designations 1 6 6 Dimensions and weights 16 7 Engine specifications 16 8 Capacities 170 Fuel 173 Catalytic converter and suspension 17 5 Electrical system 17 6.
166 Specifications T ype designation When contacting your V olvo dealer about your car and when ordering spare parts and accesso- ries, it makes things easier if you know your car ’ s type designation, vehicle identification number and engine number .
167 Dimensions and weights 0300047A KG KG KG 1. KG 2. VOLVO CAR CORP. SWEDEN MADE IN 1 2 3 4 Dimensions Length ................... 472 (XC 473) cm Width .................... 180 (XC 186) cm Height* ................. 147-149 (A WD 148-151/XC 155-156/R 145-149) cm Wheelbase .
168 2.0T BIFUEL BIFUEL 2.4 2.0T 2.5T 2.4 2.5T A WD Engine variant B5204T5 B5244SG B5244SG2 B5244S B5244 S2 B5254T2 B5244T4 a Output* (kW/rps) 132/92 103/97 103/85 125/100 103/75 154/83 162/83 AW D - -.
169 T5 R D5 2.4D 2.4D A WD D5 A WD Engine variant B5244T5 B5254T4 D5244T D5244T2 D5244T 3 a Output* (kW/rps) 191/92 220/92 120/67 96/67 85/67 A W D - 220/100 - - - (hp/rpm) 260/5500 300/5500 163/4000 130/4000 116/4000 A WD - 300/6000 - - - T orque ( Nm/rps) 350/35-83 400/33-88 340/29-50 280/29-50 280/29-46 A WD - 350/31-100 - - - (kpm/rpm) 35.
170 V olume Recommended grade T ransmission fluid Manual, 5-speed (M56/M58) 2.1 litre Transmission fluid 1 : MTF 97309 Manual, 6-speed (M66) 2.0 litre Automatic gearbox (A W55-51) 7.2 litre Transmission fluid 1 : JWS 3309 Coolant Petrol engines without turbo 8.
171 Capacities The oil grade requirement must be fulfilled even if a different viscosity is chosen. Important! Always use oil of the recommended grade and correct viscosity . Never use oil additives. These can damage the engine. If the system is topped up with a different oil, contact the nearest V olvo workshop for servicing.
172 1 Including filter change 2 If a different viscosity than that listed in this table is selected following the information in the diagram, the engine grade requirement must be fulfilled.
173 Fuel Fuel consumption and carbon dioxide emissions 2.4 B5244S2 Manual 5-speed (M56) 9.0 214 70 Automatic gearbox (AW55-51) 9 . 7 2 3 1 2.4 B5244S Manual 5-speed (M56) 9.2 220 70 Automatic gearbox ( A W55-51) 9 . 8 23 4 2.0T B5204T5 Manual 5-speed (M56) 9.
174 Fuel Specified fuel consumption Official fuel consumption figures are based on a standard driving cycle in accordance with EU Directive 80/1268 comb. Fuel consumption figures may change if the car is equipped with extra equipment that affects the car ’ s weight.
175 Catalytic converter and suspension Catalytic converter The purpose of the catalytic converter is to purify exhaust. It is located in the exhaust flow near the engine to quickly reach operating temperature. The catalytic converter consists of a monolith (ceramic or metal) with channels.
176 Electrical system General 12-volt system with voltage regulated alterna- ting current generator . Single pole system in which the chassis and engine block are used as conductors. The negative pole is connected to the chassis. The car is equipped with an extra ground lead to reduce the magnetic fields.
177 Audio (option) Overview Stereo HU-450 17 8 Overview Stereo HU-650 17 9 Overview Stereo HU-850 18 0 Audio functions 18 1 Radio functions 18 4 Cassette player 19 2 CD player 19 3 Dolby Surround Pro .
178 Stereo HU-450 5. SCAN - Automatic station search 6. EXIT - Scroll back in the menu 7. Navigation buttons – CD/radio - seek/change station or track Cassette - Fast forward/rewind /select next/previous track 8. Display 9. FM - Shortcut between FM1, FM2, FM3 10.
179 Stereo HU-650 1. POWER (On/Off) - Press VOLUME - Turn 2. Station storing buttons selection of disc in CD changer (1-6) 3. BASS – Press out and turn 4. TREBLE – Press out and turn 5. BALANCE – Press out and turn 6. F ADER – Press out and turn 7.
180 Stereo HU-850 1. POWER (On/Off) - Press VOLUME - Turn 2. Station storing buttons/selection of disc in CD changer (1-6) 3. BASS - Press and turn 4. TREBLE - Press out and turn 5. BALANCE - Press and turn 6. F ADER - Press and turn 7. SOURCE PUSH MENU – Open the main menu - Press T urn to select: Radio - FM, AM CD CD changer (option) 8.
181 Audio functions HU-450/650/850 Strömbrytare till/frånpå knappen för att sätta på eller stänga av radion. V olymkontroll Vrid ratten medurs för att höja volymen. V olymkontrollen är elektronisk och saknar ändlägen. Om du har knappsats i ratten, öka eller minska volymen med + respektive - knapparna.
182 3901858d Audio functions HU-450 Fader - Balance front/rear Set a suitable balance between the front and rear speakers by pressing out the knob and turning it to the right (volume of front pair higher) or the left (volume of rear pair higher). Balance is normalised in the centre position.
183 Balance - right/left Adjust balance by pressing the knob and turning it left or right.Balance is normalised in the centre position. Press the knob back to its original position after setting.
184 Steering wheel keypad If you have a keypad in the steering wheel, press the right or left arrow to select preset stations. NOTE: If the car is equipped with an integrated telephone, the steering wheel keypad can only be used for telephone functions when the telephone is activated.
185 Programming stations 1. Set the desired frequency . 2. Briefly press the PRESET/CD knob. Select a number by turning forwards or back- wards. Press again to store the desired frequency and station. Preset T o select a preset radio programme, turn the PRESET/CD knob to the stored number .
186 Autostoring stations AUTO seeks and stores up to ten strong AM or FM stations in a separate memory . If more than ten stations are found, the ten strongest are selected. This function is particularly useful areas in which you are unfamiliar with the radio stations and their frequencies.
187 Radio Data System - RDS RDS is a system that links specific network transmitters. It is used, for example, to tune the correct frequency of a station irrespective of the transmitter or the active sound source (e.g. CD). The system can also be used for receiving traffic information and for finding broadcasts of a specific type.
188 TP search This function allows you to listen to traffic information when travelling between different areas and countries without selecting a station. 1. Select radio mode using the FM button and press SOURCE. 2. T urn SOURCE, select ADV ANCED MENU and press SOURCE.
189 Programme types Displayed O F F PTY OFF New features New features Current affairs Current Information Info Sports Sports Education Educ Theatre Theater Culture and Art Culture Science Science Ente.
190 Automatic frequency updating The AF function is normally activate and ensures that the radio tunes to the strongest available transmitter . Activating AF: 1. Select radio mode using the FM button and press SOURCE. 2. T urn SOURCE, select ADV ANCED MENU and press SOURCE.
191 Radio functions HU-450/650/850 Resetting RDS functions Resets all radio settings to the original factory settings. 1. Select radio mode using the FM button and press SOURCE. 2. T urn SOURCE, select ADV ANCED MENU and press SOURCE. 3. T urn SOURCE, select RESET TO DE- F AUL T and press SOURCE.
192 Cassette player HU-450 3901876d 3901857d DOLBYBNR Fast forward/rewind The tape is fast forwarded by pressing and holding and is rewound with . ”FF” (fast forward) or ”REW” (rewind) is shown in the display during this time. Fast forward/rewind is interrupted if you press the button again.
193 CD player HU-650 CD player Insert a CD. If there is already a CD in the player, activate it by turning the SOURCE knob or pressing the CD shortcut key . CD eject If you press this button the CD stops playing and the disc is ejected. NOTE : For reasons of traffic safety , you have 12 seconds to handle the ejected CD.
194 External CD changer CD changer The external CD changer (option) is mounted behind the panel on the rear left side of the cargo compartment. Turn the SOURCE knob to activate CD changer mode. The CD changer resumes playing the disc and track that was playing last.
195 Internal CD changer HU-850 Internal CD changer HU-850 contains an internal 6-disc CD changer . Press the CD shortcut key or turn the SOURCE knob to activate the CD player . The CD player resumes playing the disc and track last played. Y ou can insert 6 discs in the CD player .
196 Dolby Surround Pro Logic II HU-850 Dolby Surround Pro Logic II Mode T o select Dolby Surround Pro Logic II Mode, press “ PL II ”. " PL II " is displayed.
197 Centre Level This function is used to set the level of the centre channel. 1. Press SOURCE. 2. T urn SOURCE, select ADV ANCED MENU and press SOURCE. 3. T urn SOURCE, select AUDIO SETTINGS and press SOURCE. 4. T urn SOURCE, select CENTRE LEVEL and press SOURCE.
198 T echnical data - Audio Alarm “Alarm!” is shown in the radio display when an alarm message is transmitted. The function is used to warn the driver of serious accidents or catastrophes, such as collapsed bridges, earthquakes or nuclear accidents.
199 T elephone (option) T elephone system 20 0 Operating 2 02 Call options 20 3 Memory functions 20 6 Menu functions 20 7 Miscellaneous information 21 1.
200 T elephone General rules · Put traffic safety first! If you as the driver must use the privacy handset in the armrest, park the car in a safe place. · Switch off the telephone when refuelling. · Switch off the telephone in areas where blasting work is being carried out.
201 T elephone 3905079m V70,XC70 V70 R.
202 T elephone Operating 3902219d 3903019m Switching the telephone on and off T o switch the telephone on: Turn the ignition key to position I. Press the button marked in the illustration. T o switch the telephone of f: Press the same button for three seconds.
203 T elephone Call options Making and receiving calls To place a call : enter the number and press on the steering wheel or centre console keypad (or lift up the handset). To receive an incoming call: Press the button (or lift the privacy handset). Y ou can also use Automatic answer, see menu function 4.
204 T elephone Call options (cont.) Privacy handset If you wish to talk undisturbed, use the privacy handset . 1. Lift up the handset. Enter the chosen number on the centre console keypad. Press to place a call. Adjust the volume with the knob on the side of the handset.
205 T elephone Functions during a call The following functions are available during a call (scroll with arrows): Secret mode on/off Secret mode Hold/No hold Choose if the current call is to be parked, i.
206 T elephone 3902221d Calling from the memory 1. Go into active mode and press . 2. Choose from the following alternatives: · Press and scroll with the arrows until you find the desired name. · Press the key of the first letter in the name (or enter the name) and press .
207 T elephone Menu functions 3902222d Menu function Go into active mode. Press to come to the menu function. The following applies in the menu function: · A long press on means you exit the menu function. · A short press on means that you retract, cancel or reject an alternative.
208 T elephone Main menus/submenus 1. Call register 1.1 Missed calls 1.2 Received calls 1.3 Dialled calls 1.4 Erase list 1.4.1 A ll 1.4.2 Missed 1.4.3 Received 1.4.4 Dialled 1.5 Call duration 1.5.1 L ast call 1.5.2 Number of calls 1.5.3 T otal time 1.
209 T elephone Menu 1. Call register 1.1 Missed calls: A list of missed calls is shown here. Y ou can choose to call, erase or store the number in the telephone or SIM card memory for later use. 1.2 Received calls: A list of received calls is shown here.
210 T elephone Menu 4. Call options 4.1 T ransmit number: Choose whether or not to display your number to the person you call. Contact your service provider for a permanently concealed number . 4.2 Call waiting: Choose whether or not you want to be alerted during a phone call that there is another call coming in.
211 T elephone Miscellaneous information 3903022 m 3902239d Specifications Output 2 W SIM card small Memory positions 255* SMS (Short Message Service) Y e s Computer/Fax N o Dual band Y es (900/1800) * 255 memory positions in the telephone memory . The number of memory positions on the SIM card varies depending on your subscription.
212.
213 A verage fuel consumption .................... 3 8 B Bass speaker ................................. 84, 181 Battery (jump start) ............................. 1 0 6 Battery care ................................ 162, 163 Beam length control .......
214 Direction indicators and brake lamps (rear) .......................................... 1 4 7 Direction indicators .............................. 4 2 Dolby Pro Logic Surround Sound .................................. 1 9 6 Door mirror defroster ....
215 Rails ..................................................... 1 1 4 Rain sensor (option) ............................. 4 3 Range to empty fuel tank ..................... 3 8 Rear fog lamp ........................................ 3 4 Rear seat backrest positions .
216 T yres, air pressure ................................ 1 2 6 T yre dimensions .................................. 1 2 4 T yres, direction of rotation ................. 1 2 7 T yres, driving characteristics .............. 1 2 6 T yres, fitting ......
217.
218.
219.
220.
221.
222.
223.
224.
2005 V70, V70 R & X C70 VO L VO 2 0 0 5 TP 7551 ( English ). A T 04 46 . P rinted in Sweden, Elanders Infologistics V äst AB, Mölnly c ke 2004 TP 7551 O W N E R ' S MA N U AL.
06 Maintenance and specifications Engine compartment 06 226 General Volvo service programme To keep the car as safe and reliable as possi- ble, follow the Volvo service programme as specified in the Service and Warranty Booklet. Have an authorised Volvo workshop carry out service and maintenance work.
06 Maintenance and specifications Engine compartment 06 `` 227 Engine oil dipstick Radiator Filler opening for engine oil Brake and clutch fluid reservoir (left-hand drive) Battery Relay and fuse box, engine compartment Filling washer fluid Air filter.
06 Maintenance and specifications Engine compartment 06 228 Filling and dipstick G031914 Petrol engine. G031915 Diesel engine. Change in accordance with the intervals speci- fied in the Service and Warranty Booklet. IMPORTANT When filling oil to top up, the oil being filled must have the same grade, see page 273.
06 Maintenance and specifications Engine compartment 06 `` 229 Coolant Checking and topping up the coolant G031918 When topping up the coolant, follow the instructions on the packaging. It is important that the mixture of coolant concentrate and water is correct for the prevailing weather con- ditions.
06 Maintenance and specifications Engine compartment 06 230 Filling The fluid reservoir is located on the driver's side. The fluid reservoir is protected under the cover over the cold section in the engine compart- ment. The round cover must be removed first before the reservoir cap can be reached.
06 Maintenance and specifications Lamps 06 `` 231 General All bulbs are specified, see page 237. Bulbs and spotlights that are of a special type or that are only suitable for replacement by a work- sh.
.
.
.
06 Maintenance and specifications Lamps 06 `` 235 Location of rear bulbs G031939 Lamp lens, right-hand side Position (LED)/side marker lamps Side reflector, rear Brake light Reversing lamp Indicator Brake light (LED) Brake lights and reversing lamps G032485 Both the brake light and the reversing lamp bulbs are replaced from inside the cargo area.
.
.
.
.
06 Maintenance and specifications Battery 06 240 Warning symbols on the battery Use protective goggles. Further information in the owner's manual. Store the battery out of the reach of children. The battery contains cor- rosive acid. Avoid sparks and naked flames.
.
.
06 Maintenance and specifications Fuses 06 `` 243 General All electrical functions and components are protected by a number of fuses in order to pro- tect the car's electrical system from damage by short circuiting or overloading.
.
.
06 Maintenance and specifications Fuses 06 246 Pos Function A Compressor A/C 15 Relay coils 5 Starter motor relay 30 Ignition coils 20 Glow system (5-cyl.
.
.
.
06 Maintenance and specifications Fuses 06 250 * Option/accessory, for more information, see Introduction. Pos Module (white). Function A Parking assistance, Parking camera* 5 Control module Four C* 1.
.
06 Maintenance and specifications Wheels and tyres 06 252 Wear and maintenance The correct tyre pressure results in more even wear, see page 262. Driving style, tyre pres- sure, climate and road condition affect how quickly your tyres age and wear.
.
.
06 Maintenance and specifications Wheels and tyres 06 `` * Option/accessory, for more information, see Introduction. 255 A foam block, located in the cargo area, con- tains all tools. The tools consist of a towing eye, jack* and wheel wrench*. The foam block is screwed into a bracket in the bottom of the spare wheel well.
06 Maintenance and specifications Wheels and tyres 06 256 WARNING Check that the jack is not damaged, that the threads are thoroughly lubricated and that it is free from dirt. NOTE Use the jack belonging to the car. 2. Take out the spare wheel, jack, wheel wrench and wrench for the lockable wheel bolts.
06 Maintenance and specifications Wheels and tyres 06 `` * Option/accessory, for more information, see Introduction. 257 G021780 4. Tighten the wheel bolts crosswise. It is important that the wheel bolts are tight- ened properly. Tighten to 140 Nm. Check the torque with a torque wrench.
06 Maintenance and specifications Wheels and tyres 06 258 3. Lift up the emergency puncture repair kit. Replace the parts after use. WARNING You should not drive faster than 80 km/h after the emergency tyre repair kit has been used. The temporarily sealed tyre must be changed as soon as possible (maximum driving distance: 200 km).
An important point after buying a device Volvo XC70 (2005) (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Volvo XC70 (2005) yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Volvo XC70 (2005) - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Volvo XC70 (2005) you will learn all the available features of the product, as well as information on its operation. The information that you get Volvo XC70 (2005) will certainly help you make a decision on the purchase.
If you already are a holder of Volvo XC70 (2005), but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Volvo XC70 (2005).
However, one of the most important roles played by the user manual is to help in solving problems with Volvo XC70 (2005). Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Volvo XC70 (2005) along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
