Instruction/ maintenance manual of the product TZDA 503 Beko
Go to page of 9
TZDA 503 Printed in T urkey Part no: 48 6370 00 00 BEKO plc Beko House Caxton Way Watford Hertfordshire WD18 8UF T el: 0845 6004911 Fax: 0845 6004922 e-mail: service@beko.
CONTENTS P AGE SAFETY FIRST / ELECTRICAL REQUIREMENTS TRANSPORT A TION INSTRUCTIONS INST ALLA TION INSTRUCTIONS ST ARTING TEMPERA TURE CONTROL AND ADJUSTMENT STORING FROZEN FOOD FREEZING FRESH FOOD MA.
ELECTRICAL REQUIREMENTS Before you insert the plug into the wall socket make sure that the voltage and the frequency shown in the rating plate inside the appliance corresponds to your electricity supply . Rating label is on the left hand side of the freezer liner .
IMPORT ANT INST ALLA TION INSTRUCTIONS 1. The space in the room where the appliance is installed must not be smaller than 10 cubic metres. 2. If possible avoid placing the appliance near cookers, radiators or in direct sunlight as this will cause the compressor to run for long periods.
7 8 STORING FROZEN FOOD Prepacked commercially frozen food should be stored in accordance with the frozen food manufacturer's instructions for a frozen food storage compartment. T o ensure that the high quality achieved by the frozen food manufacturer and the food retailer is maintained the following should be remembered: 1.
9 10 FREEZING FRESH FOOD Freezing capacity of your appliance in a 24 hours period is 11 kg (24.2 lb). Never exceed this maximum capacity . If large amounts of fresh food are going to be frozen, adjust the control knob to Fast Freeze. 24 hours before putting the fresh food in the fast freeze compartment.
11 CLEANING AND CARE ** W e recommend that you switch of f the freezer at the socket outlet and pull out the mains plug before cleaning. ** Never use any sharp abrasive instrument, soap, household cleaner , detergent and wax polish for cleaning. ** Use luke warm water to clean the cabinet of the freezer and wipe it dr y .
13 14 8 5 REVERSING THE DOOR W e recommend that you reverse the door before switching on for the first time. T ools required: Small and medium size flat and cross-headed screwdrivers, a pair of pliers.
15 16 GUARANTEE DET AILS Y our new Beko product is guaranteed against the cost of breakdown repairs for twelve months from the date of the original purchase. What is covered? • Repairs necessar y as a result of faulty materials, defective components or manufacturing defect.
An important point after buying a device Beko TZDA 503 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Beko TZDA 503 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Beko TZDA 503 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Beko TZDA 503 you will learn all the available features of the product, as well as information on its operation. The information that you get Beko TZDA 503 will certainly help you make a decision on the purchase.
If you already are a holder of Beko TZDA 503, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Beko TZDA 503.
However, one of the most important roles played by the user manual is to help in solving problems with Beko TZDA 503. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Beko TZDA 503 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
